TECHNICAL MANUAL CONTROL, TRANSPONDER SETS C-6280(P)/APX (NSN ) AND C-6280A(P)/APX (NSN )

Size: px

Start display at page:

Download "TECHNICAL MANUAL CONTROL, TRANSPONDER SETS C-6280(P)/APX (NSN ) AND C-6280A(P)/APX (NSN )"

Lindsay Moody
5 years ago
Views:

1 TM P TECHNICAL MANUAL ORGANIZATIONAL AND DIRECT SUPPORT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LISTS (INCLUDING DEPOT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS) FOR CONTROL, TRANSPONDER SETS C-80(P)/APX (NSN ) AND C-80A(P)/APX (NSN ) This publication has been printed by the UNITED STATES ARMY PUBLICATIONS CENTER, ST. LOUIS, MISSOURI, to meet your needs on a timely basis. HDQUARTERS, DEPARTMENT OF THE ARMY DECEMBER 978

3 TM P T ECHNICAL M ANUAL No P HDQUARTERS DEPARTMENT OF THE ARMY WASHINGTON, DC, 9 December 978 ORGANIZATIONAL AND DIRECT SUPPORT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LISTS (INCLUDING DEPOT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS) FOR CONTROL, TRANSPONDER SETS C-80 (P)/APX (NSN ) AND C-80A(P)/APX (NSN ) Current as of August 978 REPORTING OF ERRORS You can improve this manual by recommending improvements using DA Form 08- located in the back of the manua]. Simply tear out the self addressed form, fill it out as shown on the sample, fold it where shown, and drop it in the mail. If there are no blank DA Form 08- in the back of your manual, use the standard DA Form 08 (Recommended Changes to Publications and Blank Forms) and forward to the Commander, us Army communications and Electronics Materiel Readiness Command, ATTN: DRSEL-ME-MQ, Fort Monmouth, NJ In either case a reply will be furnished direct to you. Table of Contents Page Illus Figure SECTION I. Introduction II. Repair parts list Group 00 Control Transponder Sets C-80(P)/APX, , Section III. Special tools list (Not applicable) IV. National stock number and part number index This manuel supersedes TM P, February 97.

5 SECTION I INTRODUCTION TM P. Scope This manual lists spares and repair parts; special tools; special test, measurement, and diagnostic equipment (TMDE), and other special support equipment required for performance of organizational and direct support maintenance of the C-80(P)/APX and C-80A(P)/APX. It authorizes the requisitioning and issue of spares and repair parts as indicated by the source and maintenance codes.. General This Repair Parts and Special Tools List is divided into the following sections: a. Section II. Repair Parts List. A list of spares and repair parts authorized for use in the performance of maintenance. The list also includes parts which must be removed for replacement of the authorized parts. Parts lists are composed of functional groups in numeric sequence, with the parts in each group listed in figure and item number sequence. b. Section III. Special Tools List. Not applicable. c. Section IV. National Stock Number and Part Number Index. A list, in National item identification number (NIIN) sequence, of all National stock numbers (NSN) appearing in the listings, followed by a list, in alphameric sequence, of all part numbers appearing in the listings. National stock numbers and part numbers are cross-referenced to each illustration figure and item number appearance. 3. Explanation of Columns a. Illustration. This column is divided as follows: () Figure number. Indicates the figure number of the illustration on which the item is shown. () Item number. The number used to identify item called out in the illustration. b. Source, Maintenance, and Recoverability (SMR) Codes. () Source code. Source codes indicate the manner of acquiring support items for maintenance. repair, or overhaul of end items. Source codes are entered in the first and second positions of the Uniform SMR Code format as follows: Code Definition PA Item procured and stocked for anticipated or known usage. XD A support item that is not stocked. When required, item will be procured through normal supply channels. NOTE Cannibalization or salvage may be used as a source of supply for any items source coded above except those coded XA and aircraft support items as rest restricted by AR () Maintenance code. Maintenance codes are assigned to indicate the levels of maintenance authorized to USE and REPAIR support items. The maintenance codes are entered in the third and fourth positions of the Uniform SMR Code format as follows: (a) The maintenance code entered in the third position will indicate the lowest maintenance level authorized to remove, replace, and use the support item. The maintenance code entered in the third position will indicate one of the following levels of maintenance: Code Application/Explanation O - Support item is removed, replaced, used at the organizational level. F - Support item is removed, replaced, used at the direct support level. (b) The maintenance code entered in the fourth position indicates whether the item is to be repaired and identifies the lowest maintenance level with the capability to perform complete repair (i.e., all authorized maintenance functions). This position will contain one of the following maintenance codes: Code Application/Explanation F - The lowest maintenance level capable of complete repair of the support item is the direct support level. Z - No repair is authorized. (3) Recoverability code. Recoverability codes are assigned to support items to indicate the disposition action on unserviceable items. The recoverability code is entered in the fifth position of the Uniform SMR Code format as follows: Recoverability codes Definition Z - Nonreparable item. When unserviceable, condemn and dispose at the level insicated in position 3. F - Reparable item. When uneconomically reparable, condemn and dispose at the direct support level. c. National Stock Number. Indicates the National stock number assigned to the item and will be used for requisitioning purposes. d. Part Number. Indicates the primary number used by the manufacturer (individual, company,

6 TM P firm, corporation, or Government activity), which controls the design and characteristics of the item by means of its engineering drawings, specifications, standards, and inspection requirements to identify an item or range of items. NOTE When a stock numbered item is requisitioned, the repair part received may have a different part number than the part being replaced. e. Federal Supply Code for Manufacturer (FSCM). The FSCM is a 5-digit numeric code listed in SB 708- which is used to identify the manufacturer, distributor, or Government agency, etc. f. Description. Indicates the Federal item name and, if required, a minimum description to identify the item. g. Unit of Measure (U/M). Indicates the standard of the basic quantity of the listed item as used in performing the actual maintenance function. This measure is expressed by a two-character alphabetical abbreviation (e.g., ea, in, pr, etc). When the unit of measure differs from the unit of issue, the lowest unit of issue that will satisfy the required units of measure will be requisitioned. h. Quantity Incorporated in Unit. Indicates the quantity of the item used in the breakout shown on the illustration figure, which is prepared for a functional group, subfunctional group, or an assembiy.. Special information a. Usable on codes are shown in the description column. Uncoded items are applicable to all models. Identification of the usable on codes used in this publication are: Code Used on CK C-80(P)/APX Code Used on AS3 C-80A(P)/APX b. The following publication pertains to the C-80(P)/APX, C-80A(P)/APX and its components: TM , Control, Transponder Set C-80(P)/APX, C-80A(P)/APX, C-77/APX and C-783/APX. 5. How to Locate Repair Parts a. When National stock number or part number is unknown. () First. Using the table of contents, determine the functional group within which the item belongs. This is necessary since illustrations are prepared for functional groups and listings are divided into the same groups. () Second. Find the illustration covering the functional group to which the item belongs. (3) Third. Identify the item on the illustration and note the illustration figure and item number of the item. () Fourth. Using the Repair Parts Listing, find the figure and item number noted on the illustration. h. When National stock number or part number is known. () First. Using the Index of National Stock Numbers and Part Numbers, find the pertinent National stock number or part number. This index is in NIIN sequence followed by a list of part numbers in alphameric sequence, cross-referenced to the illustration figure number and item number. () Second. After finding the figure and item number, locate the figure and item number in the repair parts list.. Abbreviations Not applicable. (Next printed page is.)

7 TM P Figure..

8 TM P Figure..

9 () ILLUSTRATION (a) (b) FIG ITEM NO. NO. SECTI0N II () SMR CODE TM P (3) () (5) () (7) (8) NATIONAL DESCRIPTION QTY STOCK INC NUMBER PART IN NUMBER FSCM USABLE ON CODE U/M UNIT GROUP 00 CONTROL, TRANSPONDER SET C-80(P)/APX,C-80A(P)/APX AN507C0R SCREW,MACHINE STUD ASSY TURNLOCK AS STUD,TURNLOCK MS LAMP,INCANDESCENT MS LIGHT,INCANDESCENT PAFZZ 3 PAOZZ 5 PAOZZ XDOZZ 7 PAFZZ 7 PAFZZ 8 PAFZZ PAFZZ PAOZZ PAOZZ PAOZZ PAOZZ PAFZZ XDFFF XDFFF MS D53 533C3-533C3- MS50-3 MS MS500-A MS500-A MS MS AN508C0R LENS,INDICATOR PANEL,LIGHT AS3 PANEL,LIGHT CK DIAL,CONTROL DIAL,CONTROL SETSCREW SCREW,MACHINE LENS LAMPFILTER LENS,LAMP,FILTER LAMP,INCANDESCENT,8 VOLTS SELECT LAMP,INCANDESCENT, VOLTS SELECT LENS,LAMPHOLDER PANEL,MOUNTING AS3 PANEL,MOUNTING CK PANEL AS3 PANEL CK SCREW,MACHINE NUT,PLAIN,CLINCH EYELET,TURNLOCK CK EYELET,TURNLOCK SPRING SWITCH ASSEMBLY SELECT SWITCH ASSEMBLY SELECT PANEL,MOUNTING CK TERMINAL,LUG MS SCREW,MACHINE AS AN938 MS WASHER,LOCK...AS3 NUT,PLAIN,HEXAGON AS3 SWITCH,ROTARY PAFZZ AF3 785 SWITCH,ROTARY NUT,SELF-LOCKING AS3 3 80J3873 PANEL ASSEMBLYF MS SCREW,MACHINE

10 SECTION II () () (3) () ILLUSTRATION (a) (b) NATIONAL FIG ITEM SMR STOCK NO. NO. PART CODE NUMBER NUMBER (5) () DESCRIPTION FSCM TM P USABLE ON CODE (7) (8) QTY INC IN U/M UNIT 33 80A MS MS MS MS XDFFF CABLE ASSY SPRING PAFZZ MSRB55PN 990 CONN,RECEP,ELEC PAFZZ 50PAFZZ 5 PAFZZ 5 PAFZZ 53PAFZZ 5 PAFZZ MS MS C MS MS MS MS55C MS MS5-0P MS78 80A C C PLATE PANEL ASSEMBLY BACK SPRING SCREW,MACHINE CK SCREW,MACHINE SCREW,MACHINE WASHER,LOCK PANEL,BACK WASHER,LOCK NUT,PLAIN,HEXAGON BRACKET,ANGLE BRACKET,SWITCH NUT,PLATE ASSY POST,ELECTRICAL CK SWITCH, TOGGLE SWITCH, TOGGLE SWI TCH, TOGGLE SWITCH, TOGGLE SWITCH, TOGGLE CONTACT SLING,PLUG PLATE RIVET COVER ASSEMBLY,DUST DUST COVER STUD EYELET /(7 blank)

12 TM P Figure. Control, Transponder Set C-80(P)/APX, C-80A(P)/APX, Thumb Wheel Switch Section Exploded View. 8

13 SECTION II () () (3) () (5) () ILLUSTRATION DESCRIPTION (a) (b) NATIONAL FIG ITEM SMR STOCK PART NO. NO. CODE NUMBER NUMBER FSCM TM P USABLE ON CODE (7) U/M (8) QTY INC IN UNIT XDFFF XDOFF XDFFF C C N0EXR C359 MS C350 M C AN507C0R C SPRING HELICAL STUD,ARM DETENT ARM AND RL STUD,ROLLER ROLLER,DETENT ARM,DETENT SHAFT AND GR NUT,SLEEVE WASHER,NONMETALLIC CLIP,SPRING TENSION SCREW,MACHINE S WITCH,ROTARY STUD,IDLER DETENT WHEEL AND RING,RETAINING WASHER,SPRING WASHER,FLAT THUMBWHEEL AS3 KNOB ASSEMBLY AS3 DIAL,CONTROL CK DIAL,CONTROL AS3 GR,SPUR STUD RIVET NUT,SPECIAL CLIP,SPRING TENSION SCREW,MACHINE SHAFT,THUMB WHEEL CHASSIS ASSEMBLY CHASSIS,TH,SWITCH

14 SECTION IV NATIONAL STOCK NUMBER INDEX NOTE: LATEST NATIONAL STOCK NUMBER ASSIGNMENTS ARE INCLUDED AT END OF INDEX. FIGURE ITEM STOCK NUMBER NO. NO. STOCK NUMBER TM P FIGURE NO. ITEM NO PART NUMBER AN507C0R AN507C0R5 AN508C0R AN938 MS-50 MS5-0P MSRB55PN MS500-A MS500-A MS50-3 MS50-3- MS55C3 MS50-5 MS MS MS78 MS MS MS MS MS MS MS359- MS359- MS50-3 MS5957- MS MS MS MS5957 MS N0EXR D53 533C3-533C3- FSCM FIG. NO. ITEM NO PART NUMBER A A C350 80C C350 80C353 80C359 80C353-80C358 80C C359 80D D350-80D35 80D353 80D35 80D D D355 80D387 80D387 80D378 80J D FSCM 0078 FIG. NO. ITEM NO l LATEST NATIONAL STOCK NUMBER ASSIGNMENTS FIG. ITEM STOCK NUMBER NO. NO LATEST PART NUMBER ASSIGNMENTS PART NUMBER MS AF3 FIG. ITEM FSCM NO. NO

23 TM P

25 This fine document... Was brought to you by me: Liberated Manuals -- free army and government manuals Why do I do it? I am tired of sleazy CD-ROM sellers, who take publicly available information, slap watermarks and other junk on it, and sell it. Those masters of search engine manipulation make sure that their sites that sell free information, come up first in search engines. They did not create it... They did not even scan it... Why should they get your money? Why are not letting you give those free manuals to your friends? I am setting this document FREE. This document was made by the US Government and is NOT protected by Copyright. Feel free to share, republish, sell and so on. I am not asking you for donations, fees or handouts. If you can, please provide a link to liberatedmanuals.com, so that free manuals come up first in search engines: <A HREF= Military and Government Manuals</A> Sincerely Igor Chudov Chicago Machinery Movers