SRCTec, Inc. SUPPLIER QUALITY CLAUSES (SQC S)

Size: px
Start display at page:

Download "SRCTec, Inc. SUPPLIER QUALITY CLAUSES (SQC S)"

Transcription

1 01 SOURCE INSPECTIONS A1. Level 1: Government Source Inspection (GSI) Government Source Inspection is required prior to shipment from your facility. Upon receipt of this purchase order, notify the government representative who services your facility. If a government representative cannot be located, contact the SRCTec Procurement Department immediately. Evidence of GSI (e.g. DCMA Eagle Stamp signifying product acceptance) must accompany each shipment. A2. Level 2: Government Source Inspection (GSI) Government process monitoring and inspection is required. Evidence of GSI (e.g. DCMA Eagle Stamp signifying product acceptance) is not required prior to shipment of this product. Upon receipt of this purchase order, notify the government representative who services your facility. If a government representative cannot be located, contact the SRCTec Procurement Department immediately. B. Customer Source Inspection Source Inspection by a SRCTec non-government customer is required prior to shipment from your facility. Notify SRCTec Procurement Department a minimum of 15 days prior to shipment for scheduling purposes. C. SRCTec Source Inspection SRCTec, Inc. Source Inspection is required prior to shipment from your facility. Evidence of SRCTec Source Inspection must accompany each shipment. Notify SRCTec Procurement Department 5 days prior to shipment for scheduling purposes. SRCTec reserves the right to waive Source Inspection. If so, the SRCTec Quality Assurance Department will notify the supplier in writing. Include copy of notification with shipment papers. * The supplier is responsible for assuring that products are ready for SRCTec source inspection at the scheduled time. The Supplier s readiness includes making available all inspection and test documentation, including the P.O and drawings, inspection/test equipment, and necessary personnel required to complete the source inspection. 07 MATERIAL SAFETY DATA SHEETS A. Supplier shall furnish a legible copy of the most recent Material Safety Data Sheet (MSDS) as published by the original material manufacturer. Revision U Form #: SCM-D-002 Rev Date: 2/6/14

2 08 RE-SUBMISSION OF PRODUCT D. Failure analysis (FA) may be required for returned material. This requirement is noted on the SRCTec non-conforming material report (MDR or DDR) provided to you with the returned material. It is your responsibility to review these documents and submit the FA information as specified below when FA is required. Details shall be recorded on the SRCTec Failure Analysis Inquiry Log, found on the SRCTec website at Suppliers shall submit the FAIL form prior to re-submission of the product. Please send the form electronically to 09 INSPECTIONS/TEST DATA A1. Level 1: Delta First Article Inspection FASA, sample(s), and supporting data submitted to SRCTec. A2. Level 2: Complete First Article Inspection FASA, sample(s), and supporting data submitted to SRCTec. A3. Level 3: Documentation/Other First Article Inspection FASA only, submitted to SRCTec. A4. Level 4: Complete First Article Inspection FASA, sample(s), and supporting data reviewed at suppliers manufacturing location. B. First Article Inspection Sample Part The supplier is required to keep 1 sample (identified properly) at their facility for the life of the product or until another FAI is required, at which time they shall contact SRCTec for direction as to the previous revision sample SRCTec considers this SRCTec property and must be readily available. D. Test Data Test data will be captured electronically and stored on a network server. A backup procedure shall be in place for this server. It is agreed that test data will be supplied to SRCTec upon request. The Certificate of Compliance or shipping documents shall state Test Data available upon request. If test data is not captured electronically, then the test data must be stored in an area that prevents loss, damage, or deterioration. Suppliers shall make the records available within 2 business days from the request date. E. Critical to Function (CTF) - Electrical All characteristics/features identified as CTF must be integrated into the Product Acceptance Test (PAT) for the final assembly. Each characteristic/feature s measurement system must be analyzed for measurement variation and those results along with the PAT must be submitted to SRCTec for review and approval. Once approval has been granted the PAT will be frozen. 100% test is required. Changes Page 2 of 9

3 to the PAT must be submitted to SRCTec for review and approval prior to incorporation. F. Critical to Function (CTF) - Mechanical All characteristics/features identified as CTF must be 100% inspected. If Gage R&R, process stability, and capability can be demonstrated, SRCTec will authorize a sampling plan. 11. CUSTOMER-OWNED MATERIAL A. Direct-Shipped Material The supplier shall maintain certifications from the original seller/manufacturer for all material supplied by SRCTec, but direct-shipped to the supplier. The certifications shall be made available to SRCTec upon request. The supplier shall certify that the direct-shipped material was used in the manufacture of the product supplied under this Purchase Order. The supplier must provide complete traceability for all SRCTec -owned materials, including Work Order number and Purchase Order number on the supplier s C of C. B. Customer-Furnished (Consigned) Material The supplier shall certify that any material supplied by SRCTec was used in the manufacture of the product supplied under this Purchase Order. The supplier must provide complete traceability for all SRCTec-owned materials, including Work Order number and Purchase Order number on the supplier s C of C. The Supplier shall not return unused consigned material without authorization from the SRCTec buyer. 14. CONTROL OF LIMITED SHELF-LIFE MATERIAL This clause covers the certification and shipment requirements of items that require shelf life control of uncured compounds and storage life control of cured elastomers. The items include: Uncured compounds (for example: paint, adhesives, curing agents, primers, varnishes, elastomeric molding compounds, pressure sensitive adhesives, sealants, thread lock, inks etc.) NOTE: Items such as tapes and labels which have pressure sensitive adhesive back are categorized under uncured compounds. Cured Elastomers (for example: O-rings, gaskets, plate seals, molded shapes etc.) A. The supplier shall identify each item, package, or container with the manufacturing date or cure date and shelf/storage-life expiration date. Product shall have no less than 80% of useful life remaining at time of delivery. B. Definitions Page 3 of 9

4 Shelf Life: For uncured compounds - the maximum period of time that the uncured compounds may be stored under the manufacturer s recommended storage condition and remain suitable for use. Storage Life: For cured elastomers - the maximum period of time that the appropriate packaged cured elastomers may be stored under specific conditions, after which time it is regarded as unserviceable for the purposes for which it was originally manufactured. The time of manufacture is the time of cure for thermoset elastomers or the time of conversion into a finished product for thermoplastic elastomers C. System for Shelf Life and Storage Life Control The supplier shall maintain a documented system for storing and controlling uncured compounds with limited shelf-life and age-sensitive cured elastomers. The system shall include a method of identifying and controlling such items. D. Cure Date Identification for Storage Life Controlled Elastomers Elastomeric parts shall be identified by marking the cure date (quarter and year) on the part or container. The year shall be divided into quarters as follows: 1st quarter: January, February, March 2nd quarter: April, May, June 3rd quarter: July, August, September 4th quarter: October, November, December The cure date shall show the applicable quarter of the year by number, the letter Q, and the last two digits of the applicable year. Example: May 2008 would be designated by 2Q08. An elastomeric part cured during any given quarter is not considered one quarter old until the end of the succeeding quarter. E. Certification Requirements When shipping shelf-life controlled compounds and storage-life controlled elastomers, the supplier shall include the following additional information on the Certification of Conformance: Date of manufacture for shelf-life controlled compounds Cure date (QQ/YY) for storage-life controlled elastomers Shelf-life expiration date (MMYY) for shelf-life controlled compounds Storage life expiration date (QQ/YY) for storage-life controlled elastomers Batch and or lot number as applicable Date of shipment Manufacturer s name F. Shelf Life of Compounds Applied to Products The supplier shall maintain a documented system for identification and control of limited shelf life compounds so that compounds that had expired shelf life were not Page 4 of 9

5 used on product shipped to SRCTec. (Examples of limited shelf life compounds are adhesives and paints). G. Storage Life Control of Electronic Components The date codes marked on components shall be no older than specified by the purchase order at time of shipment. 15. TRACEABILITY IDENTIFICATION A. Serial Number Traceability The supplier shall maintain traceability of product supplied under this Purchase Order by marking with a serial number. If a serial number format is not defined on the drawing(s), Statement of Work, or Purchase Order, then the supplier shall use their standard serialization process to generate the serial numbers. B. Product Lot Number or Date Code Traceability The supplier shall maintain traceability of product supplied under this Purchase Order by marking the product (each part) with lot number or date code. If there is a conflict between the drawing and this clause, the drawing shall take precedence. C. Packaging Lot Number or Date Code Traceability The supplier shall maintain traceability of product supplied under this Purchase Order by marking the packaging with lot number or date code. If there is a conflict between the drawing and this clause, the drawing shall take precedence. 16. ELECTRO-STATIC DISCHARGE REQUIREMENT B. Electrostatic Discharge Protection The Supplier shall establish and maintain a written electrostatic discharge control program for the control of Electro-Static Discharge (ESD) during fabrication, handling, and packaging of electrical and electronic parts, assemblies, and equipment. The program must comply with the requirements of the most current version of Mil- Std-1686 or ANSI/ESD S The product supplied under this Purchase Order requires the use of Electrostatic Discharge (ESD) protective packaging. ESD protective packaging and package markings shall be in accordance with the drawing and this clause. If there is a conflict between the drawing and this clause, the drawing shall take precedence. The outer surface of the protective package for each electrostatic discharge sensitive (ESDS) part, shall be marked with an ESD caution symbol (reference EOS/ESD S8.1), notifying material handlers that ESDS items are contained inside. Pictures displayed below are acceptable examples: Page 5 of 9

6 18. COMPONENT LIFECYCLE MANAGEMENT A. The supplier shall notify their SCRTec Supply Chain Lead, in writing, within 10 working days upon learning of a parts obsolescence issue that will affect the support of the supplied product. Any such notification shall be accompanied by 1) a concise problem statement, 2) background data, and 3) specific recommendations to mitigate the problem. As part of the recommendations, the supplier shall propose alternative cost-effective trade-offs. The trade-off analysis shall include, but not be limited to: Determine candidates for End-of-life buys In-house or other vendor re-manufacture of parts Component re-design, development of alternate parts, trade studies, make/buy decisions Use of next higher assemblies The supplier shall provide their SRCTec Supply Chain Lead with a quarterly report regarding lifecycle analysis and lifetime buyout recommendations. 19. SOFTWARE/FIRMWARE A. If the product that is being supplied contains software and/or firmware and there is a need to change it, you must complete a Request for Change Authorization (RCA) per the SRCTec Supply Chain Manual. The completed RCA and the Page 6 of 9

7 software and/or firmware must be submitted to your SRCTec buyer via conventional mail (SW/FW on disk). The file must be revision controlled and traceable to the date of the change and accompanied with a Version Description Document (VDD). AT NO TIME IS SOFTWARE TO BE DELIVERED TO ANYONE OTHER THAN THE BUYER! 20. MATERIAL DISCOVERED TO BE NONCONFORMING AFTER SHIPMENT The Supplier shall promptly notify SRCTEC, in writing, when nonconforming product has been shipped. The notification shall include part numbers and rev, traceability (lot, serial, or manufacturer numbers), ship dates, quantities, and a description of the nonconformance. This applies to any nonconformance that departs from drawing, specifications, or purchase order requirements. 21. AOI REQUIREMENTS* All CCA s shall be programmed on an AOI machine to inspect for: wrong, missing or extra parts; polarity and solder joint criteria. Solder joint criteria may be inspected using X-Ray instead of AOI. Records of AOI operation by UCN and Part number shall be retained by the Seller and made available upon request. 22. AXI (AUTOMATED X-RAY INSPECTION) OF CIRCUIT CARD ASSEMBLIES Automated X-Ray Inspection (AXI) of Circuit Card Assemblies (CCA) Requirement Inspection shall be performed by Automated x-ray (AXI) and/or x-ray. CCA s shall be x- rayed for all hidden solder joints, including BGA and any other inaccessible solder joints, to ensure good solder joints have been achieved. X-ray can be used for other solder joints not inspected during AOI. Records of the AXI or x-ray by UCN and Part number shall be retained by the Seller and made available upon request. 23. CORRECTIONS Changes or corrections to records, regardless of the media, shall be made as follows: draw a single line through the old data, enter the correct data, date, and apply stamp or initials or signature of individual making the correction. No erasures, covering, or "whiteout" allowed. 24. ELECTRONIC PART DEFINITION (SOLID MODEL) Suppliers shall have a SRCTec approved procedure that outlines their translation process. The documentation must demonstrate traceability and compliance to the EPD database. Page 7 of 9

8 Revision History: Revision Date Description A 6/28/06 Initial Release B 8/07/06 Added Revision History Block. Changed QMS-F-402 to QMS-D-402 C 11/17/06 Changed all SRC references to SRCTec D 12/21/06 Changed references to SRC to SRCTec that were missed in prior revisions E 5/4/07 Added Supplier Scrap Requirements Added First Article Requirements F 4/15/08 Changed from Syracuse Research Corporation to SRCTec in 01A and 01B; Added Test Data bullet to 03A; Added last sentence to 08A; Added 08D; Re-wrote 09D. G 8/25/08 Updated various sections. H 03/06/09 Updated to be compatible with the Supply Chain Manual J 11/09/09 Removed clauses 02, 03, 04, 05, 06, 08A, 08B, 08C, 09B, 09C, 10, 12, 13, 16A, 17A, and 17B. These are addressed in the Supply Chain Manual. Clarified 15A and 15B. K 11/17/09 Added 09A Levels 1-4 L 05/04/10 Changed 16A to 16B Auto reformat issue during changes to rev J. Added the A and B back into section 11 Customer-Owned Material M 12/15/10 Updated 01A identified and defined level 1 and level 2. Updated 08D clarified requirement to include RTV Other and RTV debit. Updated 09D when test data is not captured electronically. Added 09E, 09F, and 18A. N 07/11/11 Updated 16B added clarification (text and photos) of proper marking of electrostatic discharge sensitive (ESDS) items. P 07/20/11 Added the following to 16B at the beginning The product supplied under this Purchase Order requires the use of Electrostatic 08D rewritten for clarification Added clause 19. SOFTWARE/FIRMWARE Q 8/24/11 18A: rewritten 15A and 15B: Added If there is a conflict between.. 09B:added R 12/16/11 19: removed or by replaced a detailed description of the change with accompanied with a Version Description Document (VDD). Page 8 of 9

9 S 6/12/12 Clause 16: Changed title from Packaging to Electro-Static Discharge Requirement and added first paragraph. Clause 11: Changed title from Customer-Furnished Material to Customer Furnished (Consigned) Material and added the last sentence in 11B. Added clauses 14B, 14C, 14D, 14E, 14F, 14G, 20, 21, 22, 23, & 24. Clause 14: Changed title from Limited-Life Material to Control of Limited Shelf-Life Material. Added text preceding 14A. T 8/1/13 Clause 08D: Rewritten; Removed * s and accompanying note. U 2/6/14 Changed document number from QMS to SCM Page 9 of 9

SUPPLIER QUALITY CODES

SUPPLIER QUALITY CODES Supplier Quality s D07-00125 Rev A APPROVALS NAME AND TITLE SIGNATURE DATE M.G. Blankenship Senior Director, Operations I. Jimenez Materials Manager D07-00125-02 Page 1 of 5 SQC 1 SQC 2 SQC 3 SQC 4 SQC

More information

Quality Assurance Procurement Clauses and Flow Down Requirements

Quality Assurance Procurement Clauses and Flow Down Requirements Rev: U Page: 2 of 12 5.3 The Purchasing Department will insure all Purchase Orders include the following: 5.4 5.3.1 Vendor is on the Rogerson Kratos Approved Vendor List (AVL). Located on the server in

More information

CTM. SUBJECT: Quality Clauses (Q Clauses) WI The purpose of this work instruction is to control the content of the CTM Quality clauses.

CTM. SUBJECT: Quality Clauses (Q Clauses) WI The purpose of this work instruction is to control the content of the CTM Quality clauses. 1.0 PURPOSE The purpose of this work instruction is to control the content of the Quality clauses. 2.0 PROCEDURE Only the clauses spelled out on the face of the Purchase Order apply. If the supplier cannot

More information

002 Supplier Quality System Compliance with Rocker Quality System for Suppliers is required for this Purchase Order.

002 Supplier Quality System Compliance with Rocker Quality System for Suppliers is required for this Purchase Order. Rocker Industries Supplier Quality Assurance Requirements When any of the following SQAR codes appear on a Purchase Order, the supplier must comply with the requirement. If the supplier has questions or

More information

Supplier Quality Clauses

Supplier Quality Clauses Requirement Name Management System Design, Process, or Material Changes Submission of Nonconforming Material to POC Deviation / Waiver Resubmission of Material Notification of Previous Delivery of Defective

More information

Teledyne QPR 001 Electronic Safety Products Rev F Page 1 of 9 QUALITY INSTRUCTION

Teledyne QPR 001 Electronic Safety Products Rev F Page 1 of 9 QUALITY INSTRUCTION Page 1 of 9 REV DESCRIPTION OF CHANGE APPROVAL NC Initial Release A Added 503 Counterfeit part prevention B C D E F Updated Quality provisions for all clauses Updated Quality provisions for all clauses.

More information

VOLTAGE MULTIPLIERS, INC. QUALITY SUPPLEMENT TO PURCHASE ORDERS

VOLTAGE MULTIPLIERS, INC. QUALITY SUPPLEMENT TO PURCHASE ORDERS The requirements of this supplement apply to the purchase order to which it is attached / referenced, to the extent applicable. Acceptance of the purchase order by the vendor constitutes acceptance of

More information

ThinKom Purchase Order Quality Provisions Number: Q4000 Revision: D

ThinKom Purchase Order Quality Provisions Number: Q4000 Revision: D 1 Purpose and Scope This is a reference document that specifies product unique quality requirements, in addition to those shown on the engineering drawing. These requirements are specified by number on

More information

STANDARD QUALITY ASSURANCE PROVISIONS FOR PURCHASED MATERIALS

STANDARD QUALITY ASSURANCE PROVISIONS FOR PURCHASED MATERIALS 1. GOVERNMENT/CUSTOMER SOURCE INSPECTION: a. Government/Customer inspection is required prior to shipment from your plant. Upon receipt of this order, promptly notify the Government/Customer representative

More information

Revision Date Change Author Change Summary A 04/23/2015 S. Oluwole

Revision Date Change Author Change Summary A 04/23/2015 S. Oluwole Title: Supplier Quality Clauses Page: 1 of 11 Revision Date Change Author Change Summary A 04/23/2015 S. Oluwole In case of any conflict with this document and any other requirements, the order of precedence

More information

Purchasing/Quality Clauses

Purchasing/Quality Clauses PQ-01 Paragon Space Development Corp. Quality Acceptance Articles ordered under this Purchase Order/Contract must be routed through Paragon Space Development Corp. quality department and are subject to

More information

TT Electronics Integrated Manufacturing Services Supplement to Purchase Order Quality Clauses TT Electronics Purchase Order

TT Electronics Integrated Manufacturing Services Supplement to Purchase Order Quality Clauses TT Electronics Purchase Order Q01 Quality System Requirements The supplier shall establish and maintain a quality system that conforms to the requirements of ISO 9001:2008 or AS9100 current revision or previous revision prior to its

More information

Purchase Order Quality Clause SCC20 Revision E, Effective 1/20/2015

Purchase Order Quality Clause SCC20 Revision E, Effective 1/20/2015 Clause A - Quality System Requirements All references to the term Government in any of the documents referenced below shall be replaced with the term Curtiss-Wright and/or the Government. All references

More information

SUPPLIER QUALITY CLAUSES

SUPPLIER QUALITY CLAUSES SECTION A This section defines restrictions and quality system requirements applicable when goods and services are procured to Accu-sembly, Inc. part numbers or Military, Federal or Industry specifications

More information

Trident Precision Manufacturing

Trident Precision Manufacturing Trident Precision Manufacturing QASQC Rev. A 6/7/06 Title: Supplier Quality Clauses Author: April V. Lusk Director of Quality General Suppliers are responsible for compliance to all stated Quality Clauses

More information

FIDELITY TECHNOLOGIES CORPORATION QUALITY CLAUSES

FIDELITY TECHNOLOGIES CORPORATION QUALITY CLAUSES FIDELITY TECHNOLOGIES CORPORATION QUALITY CLAUSES Applicable quality clauses of this attachment are referenced on the face of the purchase order, and are made a part thereof. Failure to include the quality

More information

PCB IPC-A 600 PCB IPC- 6012, 6018

PCB IPC-A 600 PCB IPC- 6012, 6018 APPENDIX 1: QOP-47 Procurement Quality Requirements Rev. E: QA Clauses/Codes The requirements listed in Table 1 are minimum requirements per IPC, Mil & J-standard. Details of each requirement follows Table

More information

Procurement Quality Requirements

Procurement Quality Requirements HLI*:IKII IOI,r> Procurement Quality Requirements Scope This document contains Reinhold s Procurement Quality Requirements (PQRs), which are applicable to all of Reinhold s suppliers. Purchase Order Clauses

More information

Supplier Quality Control Requirements

Supplier Quality Control Requirements 1. PURPOSE To effectively communicate Quality Control requirements to Suppliers. 2. SCOPE This procedure defines Supplier quality control requirements necessary to ensure that all purchased product and

More information

Supplier Quality Requirements Q Clauses

Supplier Quality Requirements Q Clauses Supplier Quality Requirements Q Clauses QA-0100032-Rev D DCR# 1603139 4/8/16 The following supplier quality requirements (Q Clauses), when specifically referenced in the Purchase Order by number, form

More information

Supplier Quality Clauses

Supplier Quality Clauses Requirement Name Management System Design, Process, or Material Changes Submission of Nonconforming Material to POC Deviation / Waiver Resubmission of Material Notification of Previous Delivery of Defective

More information

Special Purchase Order Clauses

Special Purchase Order Clauses SC-1 Quality System: The Supplier shall have a quality management system that conforms to: a) SAE AS9100 Quality Management Systems Aerospace Requirements b) SAE AS9110 Quality Management Systems Aerospace

More information

PROCUREMENT QUALITY REQUIREMENTS

PROCUREMENT QUALITY REQUIREMENTS PROCUREMENT QUALITY REQUIREMENTS S-TEC Corporation One S-Tec Way Mineral Wells, TX 76067 940-325-9406 The supplier shall follow S-TEC Procurement Quality Requirements (PQRs) during the fabrication of all

More information

Quality (Supplier Flow Down) Requirements

Quality (Supplier Flow Down) Requirements Quality (Supplier Flow Down) Requirements Document: F-740-1 Revision: A Date: April 1, 2013 QUALITY MANAGEMENT PROCEDURE REV: A Page 1 of 6 Applicable to All Purchase Orders All items delivered shall be

More information

Helical Products Company

Helical Products Company Q01 GENERAL REQUIREMENTS 1. Supplier Responsibilities 1.1. Delivery Certification By delivering products or services on the Contract, the Supplier certifies that such products or services are in compliance

More information

Supplier Quality Codes

Supplier Quality Codes Supplier Quality Codes Quality Dept. Z Microsystems, Inc. Revisions Rev ECO# Description Date Prepared Approved A D1605 Initial Release 1/20/14 R. Elliott J. Howell B D1653 Remove (including this Quality

More information

AEROJET PURCHASE ORDER QUALITY CLAUSES (FULL TEXT) CONTENTS

AEROJET PURCHASE ORDER QUALITY CLAUSES (FULL TEXT) CONTENTS AEROJET PURCHASE ORDER QUALITY CLAUSES (FULL TEXT) CONTENTS Page 1. GENERAL REQUIREMENTS 4 2. QUALITY SYSTEM 2.1 MIL-STD-45208A 5 2.2 MIL-Q-9858A 5 2.3 ISO 9001 5 2.4 ISO9002 5 2.5 NHB5300.4 (1B) 5 2.6

More information

Purchase Order Quality Clause SCC40 Revision G, Effective 1/20/2015

Purchase Order Quality Clause SCC40 Revision G, Effective 1/20/2015 Clause A - Quality System Requirements All references to the term Government in any of the documents referenced below shall be replaced with the term Curtiss-Wright and/or the Government. All references

More information

PI Purchase Order QC Codes

PI Purchase Order QC Codes Supplier Quality Assurance Codes PURCHASE ORDER ATTACHMENT A NOTE: The following codes are applicable to purchase orders issued to approved suppliers of Brown Precision, Inc. herein after called BPI. The

More information

Orbital ATK Alliant Techsystems Defense Electronic Systems Special Mission Aircraft Fort Worth

Orbital ATK Alliant Techsystems Defense Electronic Systems Special Mission Aircraft Fort Worth QUALITY ASSURANCE PROVISIONS FOR PURCHASE ORDER This document includes all Quality Assurance Provisions and definition available for inclusion on purchase orders and subcontracts issued by, Inc.,,, referenced

More information

EP-QC Supplier s General Requirements. Revision AH

EP-QC Supplier s General Requirements. Revision AH Supplier s General Requirements Revision AH NOTE: Unless identified as DCC CONTROLLED, a printed copy of this document is considered REFERENCE ONLY and may not be the current revision in effect. The current

More information

Supplier Quality Requirements Document (SQRD)

Supplier Quality Requirements Document (SQRD) Supplier Quality Requirements Document (SQRD) D127135 Rev. AE Supplier Quality Requirements Document Page 2 of 8 1.0 SCOPE This document applies to all worldwide production suppliers of Coherent, Inc.

More information

Supplier Quality Requirements Master List

Supplier Quality Requirements Master List Master List 1. Certificate Of Conformance: Certificate of Conformance must accompany each shipment. This certificate must include part numbers, standard / specification, latest applicable revision level

More information

TITLE: TEKTRONIX COMPONENT SOLUTIONS SUPPLIER QUALITY MANUAL

TITLE: TEKTRONIX COMPONENT SOLUTIONS SUPPLIER QUALITY MANUAL DATE OF RELEASE: 02-Jun-2017 Page 1 of 9 TITLE: TEKTRONIX COMPONENT SOLUTIONS SUPPLIER QUALITY MANUAL Change History: REV ECO ECO Completion/ Finished Date Summary of Change A01 S6-10550 29-JUL-15 Initial

More information

Rosen Aviation Supplier Quality Assurance Requirements

Rosen Aviation Supplier Quality Assurance Requirements 1. Purpose This document establishes the Quality Assurance Requirements for all Rosen Suppliers. This document is applicable to all Rosen Aviation Purchase Orders (POs). In addition to the requirements

More information

Compliance with YFTFC001 Quality System for Manufacturers is required for this Purchase Order.

Compliance with YFTFC001 Quality System for Manufacturers is required for this Purchase Order. 001 Customer Source Inspection @ Supplier As specified in the Contract / Purchase Order, YF/TFC's customer representative shall be granted the right to verify at the subcontractors premises that subcontracted

More information

Clauses applicable only when specified by Q-number on the purchase order.

Clauses applicable only when specified by Q-number on the purchase order. Clauses applicable only when specified by Q-number on the purchase order. Q1 Certification of Raw Materials. Seller shall provide with each shipment, a certification of conformance to ARROW s specification

More information

2. GENERAL REQUIREMENTS

2. GENERAL REQUIREMENTS 1. PURPOSE AND SCOPE 1.1 This document defines the Supplier Quality Requirements to be met by suppliers in the performance of the purchase order issued by Sagetech to ensure that externally provided processes,

More information

Title: PROCUREMENT QUALITY REQUIREMENTS CWCDS Dayton, OH

Title: PROCUREMENT QUALITY REQUIREMENTS CWCDS Dayton, OH Page 1 of 7 QUALITY CLAUSES Clause A - Quality System Requirements All references to the term "Government" in any of the documents referenced below shall be replaced with the term "Curtiss Wright Controls

More information

QUALITY CLAUSES. Real Time Logic, Inc Academy Ridge View, Colorado Springs, CO Phone: (719) Fax: (719)

QUALITY CLAUSES. Real Time Logic, Inc Academy Ridge View, Colorado Springs, CO Phone: (719) Fax: (719) Q1 Quality System Requirements The supplier shall implement and maintain a quality management system that complies with ISO 9001:2015 or an equivalent system that provides adequate inspection to verify

More information

LM Logistic Services Quality Notes Conversion Chart

LM Logistic Services Quality Notes Conversion Chart Page 1 of 10 LM Logistic Services s Conversion Chart The latest issue to this document is the version that is available on the Lockheed Martin Logistic Services Supplier Management website: http://www.lockheedmartin.com/us/suppliers/bu-info/aeronautics/sustainment-services.html

More information

PURCHASE ORDER PROCUREMENT CLAUSES QA25 Rev N Date: 11/13/2016

PURCHASE ORDER PROCUREMENT CLAUSES QA25 Rev N Date: 11/13/2016 GENERAL REQUIREMENTS The general Procurement Clauses as listed in Section 1 are applicable to all Sanders Purchase Orders as they pertain to the product being purchased. (for example: A First Article Report

More information

A1 The supplier shall operate and maintain an approved Quality System that is subject to approval by Curtiss Wright Defense Solutions Dayton.

A1 The supplier shall operate and maintain an approved Quality System that is subject to approval by Curtiss Wright Defense Solutions Dayton. Curtiss-Wright Defense Solutions-Dayton (CW-DSD) Quality Procedure QP 8.4.1 Title: Supplier Quality Requirements QP 8.4.1 Revision: 0 Issue Date: 8/1/18 QUALITY CLAUSES Clause A Quality System Requirements

More information

SECURE COMMUNICATION SYSTEMS INC. (Secure) QUALITY CLAUSES

SECURE COMMUNICATION SYSTEMS INC. (Secure) QUALITY CLAUSES SECURE COMMUNICATION SYSTEMS INC. (Secure) QUALITY CLAUSES These quality clauses, when referenced on a Secure s Purchase Order, are considered contractual requirements, in addition to any Purchase Order

More information

PROCUREMENT QUALITY REQUIREMENTS

PROCUREMENT QUALITY REQUIREMENTS PROCUREMENT QUALITY REQUIREMENTS S-TEC Corporation One S-Tec Way Mineral Wells, TX 76067 940-325-9406 The supplier including manufacturers and distributors shall follow S-TEC Procurement Quality Requirements

More information

Satellite Aerospace, Inc. TERMS & CONDITIONS Page 1 of 6

Satellite Aerospace, Inc. TERMS & CONDITIONS Page 1 of 6 TERMS & CONDITIONS Page 1 of 6 1.0 PURPOSE 1.1 Satellite Aerospace, Inc. Quality Requirements to Subtier Sources. 2.0 SCOPE 2.1 This document applies to all purchasing and sales personnel responsible for

More information

EP-QC Supplier s General Requirements. Revision AK

EP-QC Supplier s General Requirements. Revision AK Supplier s General Requirements Revision AK NOTE: Unless identified as DCC CONTROLLED, a printed copy of this document is considered REFERENCE ONLY and may not be the current revision in effect. The current

More information

Quality Management Systems - Requirements for Aviation, Space and Defense Organizations (AS9100)

Quality Management Systems - Requirements for Aviation, Space and Defense Organizations (AS9100) Effective Date: 04/07/2014 AJR1: Quality Management Systems - Requirements for Aviation, Space and Defense Organizations (AS9100) During the performance of this Contract/Purchase Order (C/PO), the seller

More information

GKN Aerospace Advanced Composite Structure

GKN Aerospace Advanced Composite Structure 1.0 PURPOSE To communicate GKN and/or customer specification requirements to the supplier based on all Group I and Group II purchase Orders. 2.0 SCOPE This procedure and the use of GKN Procurement Quality

More information

PO QUALITY CLAUSES PRODUCT MUST COMPLY WITH DFARS PREFERENCE FOR DOMETIC SPECIALTY METALS. MELTED IN USA OR QUALIFYING COUNTRY.

PO QUALITY CLAUSES PRODUCT MUST COMPLY WITH DFARS PREFERENCE FOR DOMETIC SPECIALTY METALS. MELTED IN USA OR QUALIFYING COUNTRY. QA-01 CERTIFICATION OF COMPLIANCE PO QUALITY CLAUSES CERTIFICATION DOCUMENTS ARE REQUIRED FROM SUPPLIER AND SUB-TIER SUPPLIER, AND SHALL BE IDENTIFIED WITH, AND INCLUDE THE FOLLOWING: OUR PURCHASE ORDER

More information

TABLE 1 PCB IPC-A 600 PCB IPC- 6012, 6018

TABLE 1 PCB IPC-A 600 PCB IPC- 6012, 6018 APPENDIX 1: QOP-47 Procurement Quality Requirements - QA Clauses/Codes The requirements listed in Table 1 are minimum requirements per IPC, Mil & J-standard. Details of each requirement follows Table 1.

More information

APPENDIX - A L-3 Communications Corporation Link Simulation & Training Division

APPENDIX - A L-3 Communications Corporation Link Simulation & Training Division Q10 QUALITY SYSTEM REQUIREMENTS Q10A ISO 9001:2008 Seller s quality system shall be in compliance with the requirements of ISO 9001, Model for Quality Assurance in Design, Development, Production, Installation

More information

L-3 PHOTONICS QUALITY CODES Reference

L-3 PHOTONICS QUALITY CODES Reference Number: SOP-068 Revision: A Revision Date: 10/06/2015 Responsible Organization: Quality Author: Grace Ross 1. Q CLAUSES QAPOR 0: NO PURCHASE CODES ASSIGNED DELETED QAPOR 1: SOURCE INSPECTION L-3 PHOTONICS

More information

Electro-Miniatures Corp. 68 West Commercial Ave. Moonachie New Jersey Phone: Fax:

Electro-Miniatures Corp. 68 West Commercial Ave. Moonachie New Jersey Phone: Fax: Electro-Miniatures Corp. 68 West Commercial Ave. Moonachie New Jersey 07074 Phone: 201-460-0510 Fax: 201-935-8153 1. PURPOSE GENERAL SUPPLIER REQUIREMENTS CLAUSE This general requirement describes the

More information

SUPPLIER QUALITY ASSURANCE REQUIREMENTS

SUPPLIER QUALITY ASSURANCE REQUIREMENTS FM-304 8/23/2018 RELEASED Page 1 of 4 1.0 SCOPE 1.1 When specified, this document defines the Quality System requirements to be met by suppliers in the performance of a purchase order issued by Computech

More information

STRAN Technologies Quality Notes

STRAN Technologies Quality Notes STRAN Technologies Quality Notes SQN-01 SQN-02 SQN-03 SQN-04 TEST DATA Test Data is required for all fiber optic cable supplied on this purchase order. An OTDR trace of every optical channel of the fiber

More information

QUALITY DEPT request to have FORM 1135 for REVIEW/APPROVAL Cycle everytime form will be updated/revised.

QUALITY DEPT request to have FORM 1135 for REVIEW/APPROVAL Cycle everytime form will be updated/revised. REF ONLY-DATA MANAGEMENT: 1 ST (2) PAGES IS NOT PART OF FORM 1135. QUALITY DEPT request to have FORM 1135 for REVIEW/APPROVAL Cycle everytime form will be updated/revised. FORM 1135 QUALITY ASSURANCE CLAUSES

More information

Quality Flow-Down Requirements to Suppliers

Quality Flow-Down Requirements to Suppliers 1.0 Calibration System Seller s (herein referred to as Supplier) calibration system shall meet the requirements or standards of; ISO 9001, ISO 10012-1, or AS9100, and ANSI-Z540-1, or MIL-STD-45662. 2.0

More information

APPENDIX A QUALITY ASSURANCE REQUIREMENTS FOR SUPPLIERS

APPENDIX A QUALITY ASSURANCE REQUIREMENTS FOR SUPPLIERS APPENDIX A QUALITY ASSURANCE REQUIREMENTS FOR SUPPLIERS A-1 QUALITY ASSURANCE REQUIREMENTS FOR SUPPLIERS Prepared/Approved By: Director of Quality Assurance Sr. Production/Sr. Supply Chain Manager Micro

More information

SL - MONTEVIDEO TECHNOLOGY, INC.

SL - MONTEVIDEO TECHNOLOGY, INC. The following codes apply when specified in SL-MTI s purchase order Q01: Minimum Quality Requirements: If this Purchase Order is for the acquisition of an article with an SL-MTI inventory part number,

More information

NAME/LOCATION AMETEK POWER AND DATA SYSTEMS 33 LEWIS ROAD BINGHAMTON N.Y 13905

NAME/LOCATION AMETEK POWER AND DATA SYSTEMS 33 LEWIS ROAD BINGHAMTON N.Y 13905 TITLE: QC CODE ASSIGNMENT & SUPPLIER DATA REQUIREMENTS AMETEK AEROSPACE AMETEK QOP NO: 8.001.583-BNG REV LTR: F QOP NUMBER: 8.001.583-BNG QUALITY OPERATING PROCEDURE REVISION LTR: F TITLE: BINGHAMTON QUALITY

More information

Quality Flow-Down Requirements to Suppliers

Quality Flow-Down Requirements to Suppliers 1.0 Calibration System: Seller s (herein referred to as Supplier) calibration system shall meet the requirements or standards of; ISO 9001, ISO 10012-1, or AS9100, and ANSI-Z540-1, or MIL-STD-45662. 2.0

More information

Prototype Integration Facility SUPPLIER QUALITY SYSTEM REQUIREMENTS

Prototype Integration Facility SUPPLIER QUALITY SYSTEM REQUIREMENTS PIF Supplier Quality System Requirements Page 1 of 8 Prototype Integration Facility SUPPLIER QUALITY SYSTEM REQUIREMENTS Approved by: (W. Daniel Featherston- signature on file) PIF Program Manager (Mitchell

More information

PPI/TZ Standard Quality Requirements for Suppliers -SQRS-

PPI/TZ Standard Quality Requirements for Suppliers -SQRS- PPI/TZ Standard Quality Requirements for Suppliers -SQRS- AS9100, ISO 13485 and ISO 9001 Revision: March 19, 2014 For questions concerning Standard Quality Requirements for Supplier (SQRS), please contact

More information

AC Incorporated Quality Clauses

AC Incorporated Quality Clauses AC Incorporated Quality Clauses 001. Quality System: The supplier shall maintain a Quality System that is in compliance with ISO 9001:2000, AS9100, MIL-Q-9858A or NADCAP AC7004 Inspection & test Quality

More information

Purchase Order Quality Requirement Clauses

Purchase Order Quality Requirement Clauses Purchase Order Quality Requirement Clauses Section I: Administrative. 1. Scope. This document lists the quality purchase requirements (QPRs) that JEM Engineering uses in business agreements such as purchase

More information

Requirements for Suppliers

Requirements for Suppliers 1.0 INTRODUCTION This document establishes requirements designed to ensure Park Engineering & Manufacturing Inc. (PEM) suppliers produce product that meets PEM s quality expectations and terms. Only suppliers

More information

Form Fit & Function Engineering, LLC 350 Seminole Drive Spartanburg, SC Supplementary Quality Assurance Clauses

Form Fit & Function Engineering, LLC 350 Seminole Drive Spartanburg, SC Supplementary Quality Assurance Clauses Supplementary Quality Assurance Clauses The Supplementary Quality Assurance Clauses specified on the face of the attached Purchase Order are listed below. Your compliance with these requirements is necessary

More information

PURCHASE ORDER REQUIREMENTS (Quality Assurance Provisions)

PURCHASE ORDER REQUIREMENTS (Quality Assurance Provisions) PURCHASE ORDER REQUIREMENTS (Quality Assurance Provisions) Requirements 1-12 and 18 are applicable to all Mission Aerospace, Inc. purchase orders issued. Requirements 13-17 are applicable when specifically

More information

SL - MONTEVIDEO TECHNOLOGY, INC.

SL - MONTEVIDEO TECHNOLOGY, INC. The following codes apply when specified in SL-MTI s purchase order Q01: Minimum Quality Requirements: If this Purchase Order is for the acquisition of an article with an SL-MTI inventory part number,

More information

STARA Purchase Order Quality Codes

STARA Purchase Order Quality Codes STARA Purchase Order Quality Codes The following quality code provisions, along with STARA s Standard Purchase Order Terms and Conditions become an integral part of the Purchase Order. Some of the codes

More information

THE FOLLOWING GENERAL REQUIREMENTS APPLY ON ALL ORDERS

THE FOLLOWING GENERAL REQUIREMENTS APPLY ON ALL ORDERS PROCUREMENT QUALITY ASSURANCE CLAUSES PAGE 1 OF 9 THE FOLLOWING GENERAL REQUIREMENTS APPLY ON ALL ORDERS A. Each certification document and report required shall be in the English language and identified

More information

SUPPLIER QUALITY REQUIREMENTS

SUPPLIER QUALITY REQUIREMENTS SUPPLIER QUALITY REQUIREMENTS Revision B January 2017 This document establishes general and special product assurance requirements clauses for use on the Purchase Order and is part of the Terms and Conditions

More information

Airborne Systems Purchase Order Quality Clauses

Airborne Systems Purchase Order Quality Clauses Airborne Systems Purchase Order Quality Clauses This document describes in detail the contract requirements for Airborne Systems Purchase Order Quality Clauses. All manufactured goods shall contain new

More information

Supplier Quality Requirements (Including Terms & Conditions)

Supplier Quality Requirements (Including Terms & Conditions) 1 General Quality Requirements 1.1 The Seller shall: a) Meet the requirements of the latest revision of the Supplier Quality Requirements (Including Terms & Conditions) and all applicable requirements

More information

QUALITY CLAUSES. As A Minimum The ATP Shall Include: Test Equipment to be used Alternate Test Equipment specified (If applicable)

QUALITY CLAUSES. As A Minimum The ATP Shall Include: Test Equipment to be used Alternate Test Equipment specified (If applicable) This document contains quality clauses that may form a part of Ocean Systems Purchase Order requirements. The applicable quality clauses will vary by part number. The clauses for each specific part number

More information

SUPPLIER REQUIREMENTS FOR QUALITY, DESIGN & MANUFACTURING

SUPPLIER REQUIREMENTS FOR QUALITY, DESIGN & MANUFACTURING SUPPLIER REQUIREMENTS FOR QUALITY, DESIGN & MANUFACTURING 1.0 PURPOSE The purpose of this document is to define the requirements of Anaren Microwave, Anaren Ceramics and MS Kennedy (collectively Anaren)

More information

PURCHASE ORDER QUALITY CLAUSES

PURCHASE ORDER QUALITY CLAUSES By accepting a purchase contract from Alva Manufacturing, you are accepting responsibility for all quality clauses listed in the body of the Purchase Order as described below: SUPPLIER QUALITY CLAUSE SUMMARY

More information

NAMMO TALLEY INC QUALITY CODES

NAMMO TALLEY INC QUALITY CODES NAMMO TALLEY INC QUALITY CODES Code NTI-001A NTI-001B NTI-001C NTI-002 NTI-003 NTI-004 NTI-005 NTI-007 NTI-008 Description Quality System - The supplier shall have a Quality Management System conforming

More information

D. All distributors shall be reviewed and approved as per company procedure.

D. All distributors shall be reviewed and approved as per company procedure. PROCEDURE Number: QM-251 Purchase Order (QAP) Quality Assurance Provisions Department: Quality Assurance Revision: 5 Publish Date: 2015-11-18 Prepared by: Quality Manager Authorised by: Director of Operations

More information

VACCO. Supplier Training. Updated 8/21/18

VACCO. Supplier Training. Updated 8/21/18 VACCO Supplier Training Updated 8/21/18 1 Table of Contents 1. Website: Quality Clauses a) Purchasing Information b) Purchase Order Review 2. Quality Flow Downs a) Purchase Order example 3. Purchasing:

More information

QUALITY CONTROL INSTRUCTION

QUALITY CONTROL INSTRUCTION QUALITY CONTROL INSTRUCTION NUMBER QCI 103 REVISION N TITLE: Servotronics Inc. Quality Clauses PURPOSE: To establish a system to implement Servotronics & Customer flow down Quality Requirements to Servotronics

More information

Airborne Systems Purchase Order Quality Clauses

Airborne Systems Purchase Order Quality Clauses Airborne Systems Purchase Order Quality Clauses This document describes in detail the contract requirements for Airborne Systems Purchase Order Quality Clauses. All manufactured goods shall contain new

More information

Supplier Quality Requirements(SQR s) SECTION 1

Supplier Quality Requirements(SQR s) SECTION 1 GENERAL REQUIREMENTS The general Supplier Quality Requirements as listed in Section 1 are applicable to all Rubbercraft purchase orders as they pertain to the product being purchased. (example: A First

More information

Supplier Quality Clauses

Supplier Quality Clauses Reviewed: Reviewed: Date: Supplier Quality Clauses 1 TABLE OF CONTENTS 1.0 PURPOSE... 3 2.0 SCOPE... 3 3.0 APPLICABLE DOCUMENTS... 3 4.0 PROCEDURE... 3 5.0 RECORDS... 4 Q1 GENERAL QUALITY ASSURANCE REQUIREMENTS...

More information

Self-Audit Checklist

Self-Audit Checklist Page 1 Company Name: Date of audit: Date of last audit performed: Name of person performing self-audit: Signature: Name of person responsible for quality system: Signature: Page 2 Number of non-compliances:

More information

Quality Management System

Quality Management System Quality Management System 6.1 Quality Q-Codes () 6.1 Quality Q-Codes Quality Clauses The following quality control clauses apply when specifically noted on the Gear Technology purchase order: Q1- Material

More information

Printed versions may not be the latest. Suppliers shall utilize the latest version which can be found on our website at

Printed versions may not be the latest. Suppliers shall utilize the latest version which can be found on our website at 6707 Hardeson Rd Everett, WA 98203-7101 USA 425-405-3500 FAX: 425-405-3599 Printed versions may not be the latest. Suppliers shall utilize the latest version which can be found on our website at www.umbragroup.it.

More information

1.0 Purpose. 2.0 General notes 3.0 QUALITY SYSTEM REQUIREMENTS. Approved by: G. Stugart Prepared by: Schelert

1.0 Purpose. 2.0 General notes 3.0 QUALITY SYSTEM REQUIREMENTS. Approved by: G. Stugart Prepared by: Schelert 1.0 Purpose This document defines PECO-Astronics (PECO) purchased material flow-down requirements. Additional specifications may also apply and will be documented on the purchase order; all requirements

More information

The Supplier shall have a quality management system that conforms to any one of the following, as applicable:

The Supplier shall have a quality management system that conforms to any one of the following, as applicable: Level III QAP 8.4.3-01 Revision B Page 1 of 12 SC-1 Quality Management System: The Supplier shall have a quality management system that conforms to any one of the following, as applicable: a) SAE AS9100D

More information

Supplier Quality Requirements

Supplier Quality Requirements Page 1 of 5 SQR-01 Quality Management Systems AS9100 Suppliers: The supplier will at a minimum maintain and implement a documented quality management system, available in the English language, which is

More information

QUALITY CLAUSE CODES

QUALITY CLAUSE CODES 14201 Myerlake Circle 5307 Luce Avenue, Bldg 243E Clearwater, FL 33760 McClellan, CA 95652 P (727) 539-8585 F (727) 539-0316 THESE ARE IN ADDITION TO THOSE SET FORTH IN ANY DOCUMENT THAT IS PART OF THE

More information

PURCHASE ORDER ATTACHMENT A COX & COMPANY SUPPLIER PRODUCT ASSURANCE PROVISIONS SPAP-1

PURCHASE ORDER ATTACHMENT A COX & COMPANY SUPPLIER PRODUCT ASSURANCE PROVISIONS SPAP-1 Page 1 of 6 PURCHASE ORDER ATTACHMENT A COX & COMPANY SUPPLIER PRODUCT ASSURANCE PROVISIONS SPAP-1 The following Product Assurance Provisions, with their terms and conditions, become an integral part of

More information

Intro Corporation Purchase Order General Terms and Conditions

Intro Corporation Purchase Order General Terms and Conditions 1 General Quality Requirements Intro Corporation Purchase Order General Terms and Conditions 1.1 The Seller shall: a) Meet the requirements of the latest revision of the Supplier Quality Requirements (Including

More information

Axiom Electronics LLC. Axiom Electronic LLC AS9100 Flow-down Requirements for Suppliers

Axiom Electronics LLC. Axiom Electronic LLC AS9100 Flow-down Requirements for Suppliers 1 of 5 Axiom Electronic LLC Q02 Q03 Q04 Q05 Q06 Q08 A legible Certificate of Conformance (C of C) is required with every shipment. Quality Assurance & Control Records used to substantiate conformance must

More information

Replaces: Not applicable.

Replaces: Not applicable. Page 1/12 SCOPE - defines the quality requirements for purchasing materials, parts and services that may affect product quality of Airborne items. does not include requirements for design and development

More information

Procurement Quality Assurance Requirements

Procurement Quality Assurance Requirements 1. REQUIREMENTS 1.1 Quality System This document provides the minimum Quality System Requirements to externally provided processes, products and services to Superior Thread Rolling (STR). Suppliers must

More information

Quality Supplier Requirements for Beckwith Electric Co., Inc.

Quality Supplier Requirements for Beckwith Electric Co., Inc. Quality Supplier Requirements for Beckwith Electric Co., Inc. This Page Left Intentionally Blank To Our Valued Suppliers: One of the primary goals of Beckwith Electric is to provide the highest Quality

More information

PROCUREMENT DOCUMENT QUALITY ASSURANCE REQUIREMENTS

PROCUREMENT DOCUMENT QUALITY ASSURANCE REQUIREMENTS Document Title Document Number PROCUREMENT DOCUMENT QUALITY ASSURANCE REQUIREMENTS STO-QR-0310 Rev. Change Order Checked by: Date Approved by: Date Safety* Date C REVISED PER TR 0051-96 XXXX XX M. Devoe

More information

PMA SUPPLIER QUALITY REQUIREMENTS QS Revision J

PMA SUPPLIER QUALITY REQUIREMENTS QS Revision J PMA SUPPLIER QUALITY REQUIREMENTS Revision Wencor, LLC Corporate Ph. (678) 490-0140 416 Dividend Drive Peachtree City, GA 30269 1625 N 1100 W Springville, UT 84663 Page 1 of 10 Page 2 of 10 SUMMARY Revision

More information