Technical Specifications and General Guidelines for Mass Flow Meters at Petroleum Oil Installations. Note:
|
|
- Elfreda Farmer
- 6 years ago
- Views:
Transcription
1 Technical Specifications and General Guidelines for Mass Flow Meters at Petroleum Oil Installations Note: These are general specifications and guidelines for Mass Flow Meters for Petroleum Oil Installations. The scope of this tender is limited to the following components of the system; 1. Supply of Mass Flow Meters of 4, 6 & 8 sizes 2. Annual Calibration of Meters 3. Annual Maintenance contract 4. Supervision of Installation & Commissioning Specifications/provisions relevant to the above scope of supply shall be applicable for this tender. Site execution works including any cabling, installation, control system, software, integration with existing terminal automation systems are not part of the scope of this tender.
2 1. Application SPECIFICATION OF CORIOLIS MASS FLOW METER FOR LIQUID HYDROCARBONS To measure the mass flow rate of MS/HSD/SKO during custody transfers in pipelines. 2. Measurement Standard API, Manual of Petroleum Measurement Standard s Chapter 5 Metering Section 6 Measurement of Liquid Hydrocarbons by Coriolis Meters. 3. Operating conditions 3.1 Flow Rate Operating: Minimum 100 KL/HR ; Maximum : 2000 KL/HR 3.2 Pressure Operating: Min :1 kg/cm2; Max : 6 kg/cm2 for 150# 3.3 Operating Temperature:5 0 C (Min); 50 0 C (Max) 3.4 Density /Viscocity/Other parameters : Please refer BIS Standards IS-1459 for SKO; IS-1460 for HSD & IS-2796 for MS 3.5 Allowable Pressure drop : 0.5 kg/cm2 (max) of the maximum flow 3.6 Corrosive Components:2500 ppm (Max) of sulphur and substantial amount of caustic is present in Hydrocarbon. 4. Process connections 3 to 10 with flanged ends 150/300/600# as per ANSI B Installation Location The proposed mass flow meter shall be installed on horizontal pipe line section which is at 0.3M-1.2M elevation above ground, supported on concrete sleepers/ Structural Supports and the mass flow meter construction/design shall comply with the installation location aforesaid. The Bidder shall provide a drawing of the recommended installation arrangement with the piping modified proposed, along with the bid. 6. Materials of construction 6.1 Coriolis Mass flow sensor (Wetted Parts): The wetted parts shall be SS316 / SS 904 L for all products. The sensor design shall consist of two U tubes of appropriate shape and shall be continuously excited at their resonant frequency. 6.2 Housing of the Flow Transmitter: Epoxy coated die-cast Aluminium 7.0. Accuracy of the Mass Flow measurement and factory calibration: 7.1 Maximum allowable error: ± 0.1 % of the reading 7.2 Repeatability& Linearity: ± 0.05% of the reading 7.3 Density accuracy : ± gm/cc
3 7.4 Density repeatability : ± gm/cc or better 7.5 Factory Calibration: The Coriolis Mass Flow meter shall be calibrated at a calibration rig which is accredited to ISO/IEC The calibration method shall be based on gravimetric measurement with weighing container. 7.6 No of calibration/test points: ISO/IEC accreditation: A copy of the ISO/IEC accreditation certificate of the calibration facility/calibration rig, shall be submitted along with the technical bid. Note : i. In case Strainer and Air eliminator are required to provide the accuracy mentioned, above the vendor shall provide the same within the quoted rate. ii. Successful vendor to satisfy himself with respect to external vibrations that may affect the accuracy of the mass flow meter before installation.suitable modifications required in piping supports may be suggested before installation so that accuracy of the meter is not affected. 8. Flow Transmitter/Display Unit 8.1 Type : Integrally mounted on the sensor unit 8.2 Display : Backlit LCD for clear visibility during poor illumination levels 8.3 Process variables available on display Mass flow in engineering Units: Volumetric Flow in engineering units: Density: Process Temperature: 8.4 Reset counter and cumulative totalizer :The Flow Transmitter/Display Unit shall be equipped with 8 Digits Cumulative Totalizer & 5 Digit Reset Counter with programmable decimal point. The reset counters shall keep track of total amount of mass transferred during each product transfer and can be viewed, started, stopped and reset through front panel controls. The cumulative totalizer shall track the same mass as reset counter but reset facility shall not be allowed. 8.5 Self Diagnostic functions The Flow Transmitter/Display Unit shall be capable of performing selfdiagnostic tests on hardware and displaying diagnostic messages and alarm features on indicator. 8.6 Output signals
4 8.6.1 The Flow Transmitter/Display unit shall have RS 485 output over MODBUS RTU and shall also be capable of generating active 4 20 ma dc current signal which is linearly proportional to the mass flow rate for remote indication The Flow Transmitter/Display unit shall be capable of generally active pulse output which can be configured to indicate the mass transferred. Number of pulses generated for a unit mass transferred, shall be user configurable. 8.7 Communication functionality: The mass flow meter could be configured, calibrated remotely using MODBUS output / HART calibrator. All the measured readings shall be transmitted over MODBUS output. Bidder shall assist the client s TAS vendor in establishing the communication with automation system. 8.8 Surge Protection: The Mass flow Meter Hardware shall be protected against surges, transients induced either by switching of heavy electrical loads or lightning. Compatible surge protectors recommended by OEM for signal and power supply, with necessary mounting accessories shall be provided. The surge protector shall be designed and tested as per the requirements of BS EN or IEEE C Ingress Protection Class: Ingress Protection Class as per IP65 as per IEC/EN Electrical Connection: ½ 14 NPT or M Coriolis mass flow meter shall be of in-line mounting design with flow direction clearly marked on the flow tube to ensure proper installation 8.12 Coriolis Flow meter shall be provided with internal temperature sensor for fluid temperature compensation 8.13 The flow meter shall be capable of computing field density and shall incorporate temperature sensor for fluid temperature measurement 8.14 The transmitter and sensor unit are separate as specified in data sheets. The interconnecting cable and suitable cable glands with PVC Shrouds shall be supplied by the bidder 8.15 Meter electronics shall be provided with security locking password to ensure restricted access to configuration & modification in settings 9.0 EMC Compliance The mass flow shall comply with generic immunity standards EN 50081, EN and EN for emission Hazardous Area Certification: Shall have approval from ATEX 11 2G Exd 11AT6 and CCOE for use in hazardous area, Zone Power supply available at the installation:240v, 50 Hz 12.0 Environmental Conditions 12.1 Ambient temperature:5 0 C 50 0 C
5 12.2 Relative Humidity: 5% - 9% non-condensing 13.0 Quality Standard/Accredited Calibration Facility The Mass Flow Meter shall be factory calibrated at a calibration rig which is accredited by the national metrology authority of the manufacturing country in accordance with ISO/IEC 17025, General requirements for the competence of testing and calibration laboratories. A copy of the ISO/IEC accreditation certificate shall be submitted along with the bid. Mass flow meters shall be flow calibrated with gravimetric method using water and shall have calibration certificate duly signed by weights and measures authority such as NMI, PTB or other reputed National standard flow Laboratory. Flow meter shall have international & national legal metrology approvals for custody transfer application. Calibration mechanism of the mass flow meters shall be sealed by weights and measures department to prevent tempering by unauthorised personnel. Calibration and sealing through weights and measures department at the time of supply and for warranty period, AMC period shall be included in the Bidder s scope. Suitable provision shall be in-built with transmitter for putting the W&M seal Custody Transfer Approvals The MFM shall have custody transfer approvals ( for Mass Flow measurement & volumetric Flow Measurement) as per OIML R117 from OIML approved Laboratories ( e.g. NMI /PTB etc.) The MFM shall also have custody transfer approvals from W&M, India. for Mass Flow measurement & volumetric Flow Measurement 14.3 Each MFM shall be calibrated at FCRI,Palghat & sealed/ stamped by W&M Dept, India,for custody transfer applications as part of original order In case approval from State W&M is required for the location in which the mass flow meter would be installed then the vendor shall have to arrange for same The supplied mass flow meter shall have facility for W&M hardware lock and software lock Warranty The mass flow meter shall be a proven design and availability of spares shall be guaranteed for at least 10 years period. The supplier shall guarantee that the design engineering and equipment supplied shall be free from defects and shall confirm to specification. All defective material shall be replaced free of charge within 24 months from the date of commissioning or 30 months from the date of delivery of last consignment whichever is earlier Documentation and operation and maintenance manuals 16.1 Product catalogues containing technical specification, options, features and functions, dimensional drawings, installation arrangements with proposed piping modifications, ISO/IEC accredited certificate for the calibration rig and hazardous area certification from CCOE of the quoted model shall be submitted with the bid.
6 16.2 Operation and maintenance manuals containing installation procedures terminal connections, wiring details, spare part lists etc. shall be supplied along with the equipment delivery The mass flow meter shall be calibrated at a calibration facility accredited by the national metrology authority of the manufacturing country in accordance with ISO/IEC 17025, prior to shipment and certified 5 point calibration test report shall be submitted along with equipment delivery. All literature shall be in English Language Calibration facility available: The location of the ISO/IEC accredited calibration facility at which recalibration services for the mass flow meter could be obtained. The vendor shall separately provide quote for carrying out calibration facility one a year from the above accredited laboratory for a period of 5 years. The rate shall include necessary to and fro freight, cost of calibration in the laboratory. SENSOR Sensor Vendor to specify Service MS/HSD/SKO Volumetric flow range Operating flow Maximum pressure Process temperature Density of fluid (Range) Viscosity Line size Process connection RF Flanged as per ANSI B 16.5 Accuracy +/- 0.1% of reading or better for mass flow Repeatability/Linearity +/- 0.05% of measured value or better Material of construction of tube SS316 or better MOC of flanges, reducer, SS 304 or better expander, nuts, bolts etc Transmitter: Power supply Output Local display Zero and span adjustment Operating temperature Safety classification Ingress Protection Transmitter housing 240 V 50 Hz RS 485 over MODBUS and 4 to 20 ma with HART communication LCD Should be possible with and without HART communicator. 5 Deg C (Min); 50 Deg. C (max) Instruments shall be suitable for working in n Zone 1, Group 2A type hazardous area as per IEC (1991) classification. IP65 Should be painted with anti-corrosive epoxy paint All standard accessories such as flanges, reducer, expander, nuts, bolts and any other accessory not mentioned but required for completeness should be supplied along with the instrument. Approved Makes: Endress& Hauser, Siemens, Forbes Marshall, Honeywell, ABB, Emerson, Rheonic,
7 Henrich, Krohne or approved equivalent (See Note 3 below) Notes: 1) Detailed technical catalogue/literature should be sent along with the offer. 2) All test/calibration certificates along with instruction manual / Operation manual in English should be provided at the time of supply. 3) A make shall be considered as approved only if Custody transfer Approval as per Clause 14 are available. 4) SS tag plate with tag number, CCOE/PESO certificate no.,process parameters and other relevant information shall be fixed on the instrument.
XMP i. Precision Pressure Transmitter for the Process Industry with HART -Communication. Stainless Steel Sensor
Precision Pressure Transmitter for the Process Industry with HART -Communication Stainless Steel Sensor accuracy according to IEC 0770: 0. % FSO Nominal pressure from 0... 00 mbar up to 0... 00 bar Output
More informationXMP i. Precision Pressure Transmitter for the Process Industry with HART -Communication. Stainless Steel Sensor
Precision Pressure Transmitter for the Process Industry with HART -Communication Stainless Steel Sensor accuracy according to IEC 0770: 0. % FSO Nominal pressure from 0... 400 mbar up to 0... 00 bar Output
More informationRosemount 1152 Alphaline Nuclear Pressure Transmitter
Product Data Sheet 00813-0100-4235 Rev BA Rosemount 1152 Rosemount 1152 Alphaline Nuclear Pressure Transmitter INDUSTRY LEADING PERFORMANCE Qualified per IEEE Std 323-1971 and IEEE Std 344-1975 Mild environment
More informationARRANGEMENT AND WORKING OF MULTIPORT FLOW SELECTOR VALVE IN PRODUCTION MANIFOLD:
GENERAL DESCRIPTION Crude oil well test manifold to be provide as Multiport Flow Selector (MPFS) technology. It provides a cost effective method for selecting and diverting well fluids from an individual
More informationVersaFlow Coriolis 1000 Mass Flow Sensor Specifications
VersaFlow Coriolis 1000 Mass Flow Sensor Specifications 34-VF-03-03 June 2012 The Superior Solution The VersaFlow mass flow sensor is the only mass flow sensor with a straight measuring tube that is available
More informationPlastic tube flowmeters Series PT/PS Variable area flowmeter for liquids and gases
Plastic tube flowmeters Series PT/PS Variable area flowmeter for liquids and gases Low cost, excellent readability and light weight Simple installation (flanged, threaded or socket ends for solvent or
More informationRosemount 1154 Alphaline Nuclear Pressure Transmitter
Product Data Sheet 00813-0100-4514 Rev BA Rosemount 1154 Rosemount 1154 Alphaline Nuclear Pressure Transmitter INDUSTRY LEADING PERFORMANCE Qualified per IEEE Std. 323-1974 and IEEE Std. 344-1975 1.1 10
More informationPD662 Loop-Powered Meter Instruction Manual
PD662 Loop-Powered Meter C US 4-20 ma Input Loop-Powered -1999 to 2999 Display Easy Four-Button Programming NEMA 4X Enclosure Loop-Powered Backlight Option 1.7 Volt Drop without Backlight 32-Point and
More informationRed Eye Multiphase Water-Cut Meter
Red Eye Multiphase Water-Cut Meter Water-cut measurements in multiphase flow. Weatherford has redefined the water-cut meter market by addressing many of the difficulties in accurately measuring water cut
More information8.27/210 * 7.28/ / / /108. n x d. b f ML00343b. Dimensions are in inches/millimeters *8.86/225 for Pg 13.5 with adapter 2.
SITRANS P DSIII Pressure Transmitters All versions of the SITRANS P transmitter, DS III series, are smart two-wire transmitters The output signal is a load-independent direct current of 4 to 20 ma proportional
More informationProline Prosonic Flow B 200 For reliable biogas flow measurement without compromise
HAASE Energietechnik AG, Neumünster Proline Prosonic Flow B 200 For reliable biogas flow measurement without compromise Process monitoring and energy balancing made easy Innovative measurement industry-optimized
More informationProduct Datasheet July Liquid Ultrasonic Flow Meters. Daniel 3812 Liquid Ultrasonic Flow Meter
Liquid Ultrasonic Flow Meters Daniel 3812 Liquid Ultrasonic Flow Meter TM Daniel 3812 Liquid Ultrasonic Flow Meter A Reliable and Economical Solution for Liquid Products Measurement Daniel 3812 Liquid
More informationHINDUSTAN PETROLEUM CORPORATION LIMITED ADDL. TANKAGE PROJECT- MUNDRA TERMINAL
NOTICE FOR INVITATION OF BIDS (DOMESTIC) FOR AUTOMATION TENDER FOR MUNDRA ADDL. TANAKGE PROJECT MUNDRA TERMINAL 1.0 BRIEF SCOPE OF SUPPLY Hindustan Petroleum Corporation Limited (HPCL) intends to augment
More informationTemperature Controllers: JC Series Digital Indicating Controllers. JC Series. High Performance Controllers...at the lowest prices anywhere!
JC Series High Performance Controllers...at the lowest prices anywhere! Structure Units available in standard DIN sizes (1/16, 1/8, and 1/4 DIN) NEMA 4X protective construction Black enclosure Programmable
More informationPro-V Multivariable Flowmeter Model M23 Insertion Vortex
Pro-V Multivariable Flowmeter Model M23 Insertion Vortex Pro-V TM Advantage: Volumetric or mass flow monitoring of most liquids, gases, and steam Multivariable meter delivers mass flow, temperature, pressure,
More informationx act i Precision Pressure Transmitter for Food Industry, Pharmacy and Biotechnology Stainless Steel Sensor accuracy according to IEC 60770: 0.
Precision Pressure Transmitter for Food ndustry, Pharmacy and Biotechnology Stainless Steel Sensor accuracy according to EC 60770: 0. % FSO Nominal pressure from 0... 400 mbar up to 0... 40 bar Output
More informationPro-V Multivariable Flowmeter Model M23 Insertion Vortex
Pro-V Multivariable Flowmeter Model M23 Insertion Vortex Pro-V TM Advantage: Volumetric or mass flow monitoring of most liquids, gases, and steam Multivariable meter delivers mass flow, temperature, pressure,
More informationILMK 382. Stainless Steel Probe. Ceramic Sensor. accuracy according to IEC 60770: standard: 0.35 % FSO option: 0.25 % FSO.
ILMK 8 Stainless Steel Probe Ceramic Sensor accuracy according to IEC 60770: standard: 0.5 % FSO option: 0.5 % FSO Nominal pressure from 0... 40 cmh O up to 0... 00 mh O Output signals -wire: 4... 0 ma
More informationVolume Flow and Gas Flow Measuring Devices
Product Overview FLOWSIC Volume Flow and Gas Flow Measuring Devices Natural Gas Metering Process Applications Emission Monitoring Ultrasonic technology made by SICK: Measurements of gas flow rates at the
More informationEuropean MID Directive for Custody Transfer Measuring Instruments Proven, certified technology for Fiscal & Custody transfer applications
European MID Directive for Custody Transfer Measuring Instruments Proven, certified technology for Fiscal & Custody transfer applications European Metrology Directive Legal metrology in Europe has undergone
More informationx act i Precision Pressure Transmitter for Food Industry, Pharmacy and Biotechnology Stainless Steel Sensor accuracy according to IEC 60770: 0.
Precision Pressure Transmitter for Food ndustry, Pharmacy and Biotechnology Stainless Steel Sensor accuracy according to EC 60770: 0. % FSO Nominal pressure from 0... 400 mbar up to 0... 40 bar Output
More informationVortex Flowmeter FV4000 (TRIO-WIRL V) Swirl Flowmeter FS4000 (TRIO-WIRL S)
Vortex Flowmeter FV4000 (TRIO-WIRL V) Swirl Flowmeter FS4000 (TRIO-WIRL S) For flow rate and volume measurement of liquids, gases and steam Fluid temperatures up to 400 C (752 F) High accuracy Short inlet
More informationProducts Solutions Services. Successful Tank Farm and Terminal Management It starts with safety, efficiency and simplicity
Products Solutions Services Successful Tank Farm and Terminal Management It starts with safety, efficiency and simplicity 2 Successful Tank Farm and Terminal Management Keep your tank farm running safe,
More informationLiquid level switch BW 17
KROHNE 09/2001 7.02369.21.00 GR/PRINTO Liquid level switch Status: 10/99 Variable area flowmeters Vortex flowmeters Flow controllers Electromagnetic flowmeters Ultrasonic flowmeters Mass flowmeters Level
More informationOPTIMASS 7400 Technical Datasheet
OPTIMASS 7400 Technical Datasheet Sensor for mass flow The optimum meter for demanding applications A single straight measuring tube Choice of 4 tube materials The documentation is only complete when used
More information3 PHASE ENERGY ELECTRONIC METERS MKB-363-M INSTRUCTION MANUAL ( M / 00 B
3 PHASE ENERGY ELECTRONIC METERS MKB-363-M INSTRUCTION MANUAL ( M 981 198 / 00 B ) (c) CIRCUTOR S.A. -- MKB-363-M ELECTRONIC METERS -- M-981198 -- Page Nº 2 THREE-PHASE THREE-WIRE ACTIVE ENERGY ELECTRONIC
More informationGilflo flowmeters. for steam, liquids and gases
Gilflo flowmeters for steam, liquids and gases The Gilflo spring loaded variable area flowmeter... offers an unrivalled 1:1 turndown and can be used to meter most industrial fluids including steam and
More informationShur-Shot X-Proof Hydrogen Fluoride Alarm Operations Manual
Shur-Shot X-Proof Hydrogen Fluoride Alarm Operations Manual P/N 1000006053 Rev E $7%$QDO\WLFV// //& 733 Dairy Rd. Parkton, Md. 21120 www.atbanalytics.com (410) 733-6365 Table of Contents Chapter 1: Getting
More informationGENERAL PROVISIONS: Furnish and install one steel deck platform motor truck scale and associated electronic controls.
GENERAL PROVISIONS: Furnish and install one steel deck platform motor truck scale and associated electronic controls. The scale shall have a clear and unobstructed weighing surface of not less than 70
More informationFGA 300 Panametrics Flue Gas Oxygen Analyzer. GE Sensing. Features. Applications
Applications An ex situ zirconium oxide analyzer for excess oxygen measurement in dirty, rugged combustion applications such as: Boilers: all fuels and all types, including marine, recover, and utility
More informationWP-SDC COPPER CAN REGISTER WOLTMAN WATER METER
WP-SDC COPPER CAN REGISTER WOLTMAN WATER METER WP-SDC Copper Can Register Woltman (Turbine) Belanto WP-SDC is TURBINE Woltman water meter with magnetic transmission, super dry type register for industrial
More informationTSK S 3. Flap Flowmeter for liquids. Range: m 3 /h. Accuracy: ± 2.0 of reading. : PN 40, t max: C. p max
Flap Flowmeter for liquids measuring monitoring analysing TSK Range: 0.5-3.5 200-1500 m 3 /h Accuracy: ± 2.0 of reading p max : PN 40, t max: -40 +300 C Connection: wafer flange DN 25 500 Material: stainless
More informationDigital E3 Modulevel Liquid Level Displacer Transmitter
Digital E3 Modulevel Liquid Level Displacer Transmitter D E S C R I P T I O N The Digital E3 Modulevel is an advanced, intrinsically safe two-wire instrument utilizing simple buoyancy principle to detect
More informationSITRANS F X SITRANS F. Answers for industry. Vortex flowmeter The optimum measurement device for steam, gases and liquids
SITRANS F X Vortex flowmeter The optimum measurement device for steam, gases and liquids SITRANS F Answers for industry. Totally integrated solutions from a single supplier Industry segments: Chemical
More informationDIVA flowmeter. for saturated steam flow measurement
DIVA flowmeter for saturated steam flow measurement DIVA the Direct In-line Variable Area flowmeter... Energy is often treated as an overhead but can represent a considerable part of the cost of production
More informationLIQUID CONTROLS. Terminal and Bulk Plant Metering Applications. Application Brochure:
LIQUID CONTROLS Terminal and Bulk Plant Metering Applications Application Brochure: 200-40 www.lcmeter.com Premier products, premier performance Liquid Controls Group offers a broad selection of positive
More informationELECTRONIC EARTHING EQUIPMENT SERIES GRD 4200
ELECTRONIC EARTHING EQUIPMENT SERIES GRD 4200 The GRD 4200 is an electronic earthing equipment for tankers during loading and unloading operations of flammable liquids in places with danger of explosion.
More informationFlow Measurement SITRANS F M
Overview The MAG is an electromagnetic flow sensor in a large variety that meets the demands of almost every flow application. Benefits Wide range of sizes: DN 15 to DN 2000 (½ to 78 ) The flexible design
More informationVERIS Accelabar. Superior Flow Measurement Accuracy
VERIS Superior Flow Measurement Accuracy Designs, materials, weights and performance ratings are approximate and subject to change without notice. Visit for up-to-date information. ...A New Idea in Flow
More informationThe following document can be provided to an Engineer, Contractor, or Owner to allow them to
MESAN series MXL Engineering Guide Specifications The following document can be provided to an Engineer, Contractor, or Owner to allow them to properly specify MESAN s MXL series Cooling Towers. 15XXX-
More informationTank Scale Service Checklist
Tank Scale Service Checklist Specifying Service for Optimized Weighing Processes Selecting the right weighing equipment is an important first step to ensuring that your weighing processes are able to meet
More informationTSK. Flap Flow Meter for Liquids. Range: m 3 /h Accuracy: ± 2.0 of reading p max
Flap Flow Meter for Liquids measuring monitoring analysing TSK Range: 0.5-3.5 200-1500 m 3 /h Accuracy: ± 2.0 of reading p max : PN 40, t max: -40 +300 C Connection: wafer flange DN 25 500 Material: stainless
More informationP.V.C. INSULATED ALUMINIUM SERVICE MAIN WIRE-FINISHED PRODUCT
CEB SPECIFICATION 005-1: 2012 P.V.C. INSULATED ALUMINIUM SERVICE MAIN WIRE-FINISHED PRODUCT CEYLON ELECTRICITY BOARD SRI LANKA Telephone: +94 11 232 0953 Fax: +94 11 232 3935 CONTENTS PAGE 1. Scope 03
More informationUsing the PPM2 Portable Trace Moisture Transmitter
APPLICATION NOTE 2016_0106 PPM2 Using the PPM2 Portable Transmitter The Model PPM2 Portable analyzer is a compact, cost effective, analyzer specifically designed to continuously measure low levels of moisture
More information.2 The scales and automated system for each of the three (3) scales shall be supplied from a single manufacturer.
New Entrance and Scale Facility Page 1 of 6 1. GENERAL 1.1 Work Included.1 The intent of the work under this section is to supply and install three (3) complete low profile platform (pitless) truck scales
More informationData Sheet. Measuring System trikon Vortex Flow Meter EDZ 420 in Microprocessor Technology. Vortex meter trikon EDZ 420.
Data Sheet Measuring System trikon Vortex Flow Meter EDZ 420 in Microprocessor Technology Application Metering and recording of volume or mass flow of gases, liquids and steam. Vortex meter trikon EDZ
More informationMATERIAL AND EQUIPMENT STANDARD FOR PIG LAUNCHING AND RECEIVING TRAPS
MATERIAL AND EQUIPMENT STANDARD FOR PIG LAUNCHING AND RECEIVING TRAPS CONTENTS : PAGE No. 1. SCOPE... 3 2. SOURCES AND REFERENCES... 3 2.1 Sources... 3 2.2 References... 4 3. UNITS... 5 4. SERVICE CONDITIONS...
More informationLEASE AUTOMATIC CUSTODY TRANSFER UNITS (LACT UNITS)
LEASE AUTOMATIC CUSTODY TRANSFER UNITS (LACT UNITS) The Custody Transfer concept applies when the possession of crude oil or petroleum product is transferred from one legal entity to another. LACT units
More informationBioTector System-C. Online TOC Analyzer for Clean Water Applications
NEW BioTector System-C Online TOC Analyzer for Clean Water Applications SMALL ANALYZER BIG IMPACT! The NEW BioTector System-C Online TOC Analyzer is designed to meet the needs of Condensate Return, Cooling
More informationVortex Mass Flowmeter
Technology Solutions TE-VOR 1300C Vortex Mass Flowmeter FOW www.tek-trol.com Flow evel Temperature Pressure Valves Analyzers Accessories TekValSys Introduction A Tek-Vor 1300C Vortex Flowmeter (also called
More informationAT9000 Advanced Transmitter Absolute Pressure Transmitters
No. SS2-GTX00A-0500 AT9000 Advanced Transmitter Absolute Pressure Transmitters OVERVIEW AT9000 Advanced Transmitter is a microprocessor-based smart transmitter that features high performance and excellent
More informationResults of the IEC Functional Safety Assessment
Results of the IEC 61508 Functional Safety Assessment Project: 3051S Electronic Remote Sensors (ERS ) System Customer: Emerson Automation Solutions (Rosemount, Inc.) Shakopee, MN USA Contract No.: Q16/12-041
More informationF Series Flow Meter F300. User Manual
F Series Flow Meter F300 User Manual Contents 1. F300 Series Flow Meter ------------------------------------- 2 1.1 F300 Series Flow Meter Structure Drawing ---------------------------- 2 1.2 Introduction
More informationTABLE OF CONTENT
Page : 1 of 9 Project Engineering Standard www.klmtechgroup.com KLM Technology #03-12 Block Aronia, Jalan Sri Perkasa 2 Taman Tampoi Utama 81200 Johor Bahru Malaysia TABLE OF CONTENT SCOPE 2 REFERENCES
More informationVersaFlow Coriolis 200 Sensor for Mass Flow Technical Datasheet. Specification. The solution for bulk mass flow measurement. Features.
VersaFlow Coriolis 200 Sensor for Mass Flow Technical Datasheet 34-VF-03-12 October 2009 Specification The solution for bulk mass flow measurement The VersaFlow Coriolis 200 has been developed to meet
More informationTECHNICAL SPECIFICATIONS for 100Ci Ir-192 source projector(exposure device /Camera )
S-104-Q-ISTOPE CAMERA-PtB TECHNICAL SPECIFICATIONS for 100Ci Ir-192 source projector(exposure device /Camera ) S. No. PARTICULARS BHEL SPECIFICATIONS 1.0 Area of Application For Gamma Radiography of materials
More informationSARDAR VALLABHBHAI NATIONAL INSTITUTE OF TECHNOLOGY,SURAT
SARDAR VALLABHBHAI NATIONAL INSTITUTE OF TECHNOLOGY,SURAT TENDER NOTICE Sealed tenders are invited in duplicate from the supplier/manufacturer/distributor/vendor for the supply of the following items.
More informationGlass Reinforced Polyester Enclosures BPG. Glass Reinforced Polyester Enclosures
BPG 42 The BPG range comprises 16 sizes of enclosure manufactured in glass reinforced polyester (GRP). This material is highly resistant to contamination from oils, fats, aliphatic and aromatic carbohydrates,
More informationTECHNICAL SPECIFICATION FOR CLAMPS & CONNECTORS FOR 66/132/220/400 KV SUB-STATION
GUJARAT ENERGY TRANSMISSION CORPORATION LTD. Sardar Patel Vidyut Bhavan, Race Course, Vadodara: 390 007 TECHNICAL SPECIFICATION FOR CLAMPS & CONNECTORS FOR 66/132/220/400 KV SUB-STATION GETCO/E/TS-C&C
More informationModel BF 720 Incubators Avantgarde.Line with forced convection
Model BF 720 Incubators Avantgarde.Line with forced convection The BINDER incubator of the BF Avantgarde.Line series with forced convection is suitable for all gentle incubation applications, particularly
More informationRotameter. Series 134 glass tube variable area flowmeter. Data sheet Principle of operation. Philosophy. process measurement solutions
process measurement solutions 3 Rotameter Series 3 glass tube variable area flowmeter Data sheet 70 A range of quality glass tube V.A. flowmeters for general purpose & industrial applications Robust construction
More informationTECHNICAL SPECIFICATIONS DIVISION 16 - ELECTRICAL SECTION DETAIL SPECIFICATIONS FOR ELECTRICAL INSTALLATION
PART 1 - GENERAL 1.01 SCOPE The work covered by this section shall include furnishing and/or installation of all electrical and instrumentation equipment and necessary wiring systems required to provide
More informationSPECIFICATION SHEET JUNCTION BOXES
SPECIFICATION SHEET JUNCTION BOXES 8484-SS8201-8010 0 DOCUMENT NO REV SHEET 1 OF 1 CLIENT : HPCL, MUMBAI PROJECT : LPG BOTTLING PLANT, ANANTAPUR PLANT : - LPG BOTTLING PLANT ISSUED FOR : PROPOSAL ENQUIRY
More informationPRODUCT CONFORMITY CERTIFICATE
PRODUCT CONFORMITY CERTIFICATE This is to certify that the FLOWSIC100 Gas Flowmeter Manufactured by: SICK Engineering GmbH Bergener Ring 27 01458 Ottendorf-Okrilla Germany Has been assessed by Sira Certification
More informationTVA Target Variable Area Flowmeter
spiraxsarco.com/global/us TVA Target Variable Area meter for saturated steam 1 2 T V A f l o w m e t e r spiraxsarco.com/global/us Make Your Processes More Productive, Efficient and Sustainable Total Control
More informationMJK Automation YOUR PARTNER FOR WATER PROCESSING INSTRUMENTATION BROCHURE EN 1.00 PRODUCT BROCHURE 1401
MJK has 35 years of experience as a manufacturer and supplier of measuring and control equipment for water and wastewater plants. Our network of MJK sales channels serve 40+ countries worldwide. 1 MJK
More informationSG06UNINC-Series BGA/IP55/P Series in Outdoor Designed
SG06UNINC-Series BGA/IP55/P Series in Outdoor Designed BIOGAS measurement and analysis in continuous of methane, carbon dioxide, hydrogen sulphide, oxygen and hydrogen. BGA/INCA as INnovative Case Analyzer
More informationFlanged Water Meters (non-continuous flow)
Flanged Water Meters (non-continuous flow) Features MW-F Suitable for use with domestic water Pulsed output Low head loss Specification Product Codes Meter: Cold water: Fluid temp. range: Cold 0 to 30
More informationNo.: MTL/PUR/13/06/Pt.XVI/(J)/10 DATE :
No.: MTL/PUR/13/06/Pt.XVI/(J)/10 DATE : 24.05.2006 ASSAM GAS COMPANY LIMITED AN ISO 9001;2000 COMPANY ( A GOVT. OF ASSAM UNDERTAKING ) P.O. DULIAJAN, PIN 786 602 DIST. DIBRUGARH (ASSAM) Sealed tenders
More informationMeasurement & Analytics Measurement made easy. AlSCAN TM and AlSCAN TM Argon Hydrogen analysis in liquid aluminum
Measurement & Analytics Measurement made easy AlSCAN TM and AlSCAN TM Argon Today s global economy and competition have compelled aluminum producers and aluminum foundries to produce the highest possible
More informationSmart Displacement type Level Transmitter
No. SS-SLX100-0100 Smart Displacement type Level Transmitter Model SLX OVERVIEW The SLX series is a complete line of highly accurate and reliable high-performance torque tube type displacement level transmitters
More informationThe Ton-Tel Weighbridge
The Ton-Tel Weighbridge Plug-and-Weigh Technology Built to last in a tough environment Proven reliability, lower total cost of ownership. Digital Load Cell weight sensors sealed to IP68. Plug-and-Weigh
More informationSST-II HYDRAULIC BI-FOLD SPECIFICATIONS
PART 1 GENERAL 1.01 DESCRIPTION A. General 1. Furnish SST-II Hydraulic Bi-Fold System complete from one manufacturer. Provide all labor, materials, tools and equipment to furnish the SST-II Bi-Fold System
More informationThermal Mass Flow Meters Help Reduce Energy Costs and Enhance Emissions Monitoring Systems
Thermal Mass Flow Meters Help Reduce Energy Costs and Enhance Emissions Monitoring Systems Fox Thermal Instruments, Inc. Rich Cada 399 Reservation Rd. Vice President of Sales & Marketing Marina, CA 93933
More informationAddy Baksteen June 20, 2016 HONEYWELL'S VISION ON THE FUTURE OF MEASUREMENT
Addy Baksteen June 20, 2016 HONEYWELL'S VISION ON THE FUTURE OF MEASUREMENT Topic for Today 1 Short Introduction to Elster Precision Solutions Industry Trends History of Diagnostics From Diagnostics to
More informationMechatronic pressure measurement. Applications. Special features. Description
Mechatronic pressure measurement Diaphragm pressure gauge with switch contacts Model 432.56, high overload safety up to 100 bar Model 432.36, safety version, high overload safety up to 400 bar WIKA data
More informationSPRING LOADED THERMOCOUPLE CONFIGURATIONS THERMOWELL & REPLACEABLE INSERT II 2G/D Ex e TCRE/WE
SPRING LOADED THERMOCOUPLE CONFIGURATIONS THERMOWELL & REPLACEABLE INSERT II 2G/D Ex e TCRE/WE C20 C21 C26-2 C26-2 1 FEATURES TECHNICAL SPECIFICATION ASSEMBLY The industrial spring loaded configuration
More informationSIWAREX FTC-B Weighing Module for Belt Scales Set-up of SIWAREX FTC with SIWATOOL FTC_B
SIWAREX FTC-B Weighing Module for Belt Scales Set-up of SIWAREX FTC with SIWATOOL FTC_B Quick Guide For modules with order number 7MH4900-3AA01 1 Hardware Requirements... 3 2 Connections... 5 3 SIWATOOL
More informationMarine motors. 10/2 Orientation 10/2 Overview 10/3 Benefits 10/3 Application 10/3 Technical specifications 10/5 More information
/2 Orientation /2 Overview /3 Benefits /3 Application /3 Technical specifications /5 More information /6 Type approved standard motors up to frame size 315 L /6 Overview /7 Type approved explosion-proof
More informationN N O V A T I O N E F F I C I E N C Y Q U A L I T Y. Vertical Sump Pumps
N N O V A T I O N E F F I C I E N C Y Q U A L I T Y Vertical Sump Pumps For more than 60 years the name Ruhrpumpen has been synonymous worldwide with innovation and reliability for pumping technology Ruhrpumpen
More informationSPECIFICATION SHEET. Measurement method. Measurement range switching. cell. 1 /2 inch dia ppm. cylinder cell. 1 /4 inch dia.
ISO-400 ISO-00 SPECIFICATION SHEET SS CONCENTRATION ANALYZER Model: SSD-0- Model: SSD-20- Model: SSD-30- DKK-TOA manufactures three versions of suspended solids concentration analyzers according to the
More informationSilica Analyzer. Automated Silica Measurement Dependable and Sensitive
Silica Analyzer 2800Si Silica Analyzer Fully automatic calibration Trace sensitivity Grab sample capability Low maintenance Automated Silica Measurement Dependable and Sensitive Silica Analyzer 2800S i
More informationChoosing The Correct Flow Meters For Hydraulic Fracturing
WHITE PAPER Choosing The Correct Flow Meters For Hydraulic Fracturing INTRODUCTION Hydraulic Fracturing requires accurate and durable flow meters to monitor several processes during a fracking treatment.
More informationGENERAL PROVISIONS: Furnish and install one steel platform motor truck scale and associated electronic controls.
GENERAL PROVISIONS: Furnish and install one steel platform motor truck scale and associated electronic controls. The scale shall have a clear and unobstructed weighing surface of not less than 70 feet
More informationSensor unit MC2 for toxic gases and oxygen with analog output
Page 1 July 2016-2 Exchangeable sensor unit including digital value processing, temperature compensation and self control for the continuous monitoring of the ambient air. The sensor unit MC2 houses a
More informationElectromagnetic flowmeter ProcessMaster FEP300/500 The first choice for the process industry
Electromagnetic flowmeter ProcessMaster FEP300/500 The first choice for the process industry ProcessMaster For all applications ProcessMaster is the perfect fl owmeter for various industries: chemical,
More information4690 Series Turbidity systems. Accurate, reliable turbidity measurement
Data sheet DS/4690 EN Rev. B 4690 Series Turbidity systems Accurate, reliable turbidity measurement Flow-through turbidity design Fast response to process turbidity changes due to minimal sample residence
More informationHigh Capacity Weigh Modules
FEATURES Capacity range: 200K and 300K lb (90.7K and 136K kg) Low profile and low deflection with symmetrical mounting bolt pattern for easy installation Floating design allows for thermal expansion and
More informationTHE MICROFLOW SENSOR MICROFLOW SENSOR WITH A WIDE RANGE OF APPLICATIONS THANKS TO THE AVAILABILITY OF DIFFERENT CONNECTION TYPES
THE MICROFLOW SENSOR MICROFLOW SENSOR WITH A WIDE RANGE OF APPLICATIONS THANKS TO THE AVAILABILITY OF DIFFERENT CONNECTION TYPES The manufacturer guarantees only English text. Available on our web site:
More informationTechnical System Catalogue Modular PDU (PSM)
Technical System Catalogue Modular PDU (PSM) Benefits of PSM busbars at a glance Modular configuration, flexibly extendible Redundant designs in busbars are supported Vertical mounting in the rack without
More informationThermocouple for Flue Gas Temperature Measurements,
Electrical Temperature Measurement Thermocouples for Flue Gas Temperature Measurements Model TC81 with Thermowell Model TW81 WIKA Data Sheet TE 65.81 Applications Blast furnaces, air heaters Red-heat and
More informationFlowmeters. Positive Displacement meter. Coriolis mass flowmeter. Turbine flowmeter. Ultrasonic flowmeter
The Satam range is used for the custody transfer measurement of liquid hydrocarbons, liquid gas and liquid chemicals. Consisting of four distinct families, the range is able to meet the needs of most industrial
More informationPIP PCEPA003 Process Analyzer System Field Installation Guidelines
January 2016 Process Control PIP PCEPA003 Process Analyzer System Field Installation Guidelines PURPOSE AND USE OF PROCESS INDUSTRY PRACTICES In an effort to minimize the cost of process industry facilities,
More informationIndustrial Flowmeters
spiraxsarco.com/global/us Industrial Flowmeters High-accuracy solutions for steam, gas and liquid flow applications 1 2 F l o w M e a s u r e m e n t S o l u t i o n s spiraxsarco.com/global/us Make Your
More informationInstruction Manual HI RH/ C Transmitter. This Instrument is in Compliance with the CE Directives.
Instruction Manual HI 8666 RH/ C Transmitter This Instrument is in Compliance with the CE Directives www.hannainst.com Dear Customer, Thank you for choosing a Hanna Instruments Product. Please read this
More informationMETERING TO DATA MANAGEMENT
R MID APPROVED t o 2 0 0 WATER MEASUREMENT NUBIS FROM METERING TO DATA MANAGEMENT PROPELLER WATER METER WITH HORIZONTAL IMPELLER AXLE Nubis is propeller, dry water meter Woltman s type, with horizontal
More informationReduce costs, improve well testing, and maximize production
Reduce costs, improve well testing, and maximize production Integrated Well Testing Skid Solution Proven automation solutions and local expertise to help you overcome your toughest challenges. Informed
More informationFor Safe and Delicious Water
RESIDUAL CHLORINE ANALYZER 400G NON-REAGENT FREE CHLORINE ANALYZER FC400G 400G RESIDUAL CHLORINE ANALYZER FC400G NON-REAGENT FREE CHLORINE ANALYZER Bulletin 12F01A01-01E www.yokogawa.com/an/ For Safe and
More informationASSAM GAS COMPANY LIMITED ( A GOVT OF ASSAM UNDERTAKING) P.O. DULIAJAN, DIST. DIBRUGARH PIN , ASSAM, INDIA
ASSAM GAS COMPANY LIMITED ( A GOVT OF ASSAM UNDERTAKING) P.O. DULIAJAN, DIST. DIBRUGARH PIN 786602, ASSAM, INDIA Tender Notice No. PGC/NRL/COMP/1/04/52 Date: 16/02/2005 Assam gas Company invites sealed
More information