Operation Manual. Europe Bill Acceptor EBA SD2 CHAPTER 2. JAPAN CASHMACHINE CO., LTD. Copyright 1997 Japan Cash Machine
|
|
- Jeffery Wade
- 5 years ago
- Views:
Transcription
1 Europe Bill Acceptor EBA SD2 CHAPTER 2 Operation Manual DWG No Date JAPAN CASHMACHINE CO., LTD. Copyright 1997 Japan Cash Machine
2 1 Features Validator EBA-10-SD2 provides the following features.!setting for accepting a bill You can set the DIP switch to accept or refuse each of 5 types of bills independently. You can also set the DIP switch to accept all 5 types of bills.!simple bill collection Since you can detach the stacker box itself from the main unit, the bills can be collected easily. Also, the stacker box is provided with a lock to offer high security. The stacker box can store up to 400 bills.! Bill theft prevention mechanism A security device is installed to prevent any illegal action. Once a bill is fed into the unit, it cannot be pulled out. Japan Cash Machine Co., Ltd. Class EBA-10-SD2 Chapter 2(4) Date Dwg No Page 1
3 2 Component Name Red LED Japan Cash Machine Co., Ltd. Class EBA-10-SD2 Chapter 1 Date Dwg No Page 1
4 3 Precautions 1. Do not insert a torn, 2. Never expose the unit in 3. Do not install the unit wet bill. It will get in water. The unit in a dusty invironment. Jammed in the unit. contain several precision Dust will lower the electronic devices which can be damaged if water or any liquid is sprayed or spilled into the unit. performance of the bill sensor. 4 Collecting Bills 1. Unlock and pull out the stacker box. 2. Take out the bills. Japan Cash Machine Co., Ltd. Class EBA-10-SD2 Chapter 1 Date Dwg No Page 1
5 5 When the Acceptor is Jammed (1) When bills are jammed near the entrance of the stacker box, unlock the box and pull it out to remove the jammed bills. (2) Loosen 2 knobs each from either side to open the acceptor head and remove the jammed bills. Japan Cash Machine Co., Ltd. Class EBA-10-SD2 Chapter 2(4) Date Dwg No Page 4
6 (1) When you cannot remove jammed Bills even after opening the acceptor head, open the cover of bill theft prevention unit to remove the jammed bills and strings. (4) When bills are jammed in the feed route, remove 2 screws at the back and 2 screws each from either side of the stacker storage unit to pull out the feed unit and remove the jammed bills. Japan Cash Machine Co., Ltd. Class EBA-10-SD2 Chapter 2(4) Date Dwg No Page 5
7 6 Cleaning When the scanning unit and its sensor becomes dirty, this could cause paper jams and deterioration of the bill sensing capability. Periodically open the acceptor and bill theft prevention unit and clean the inner parts of these units. Use a soft cloth or cotton swab to clean the inner parts. If you cannot remove a stain, wipe it using a cloth or cotton swab moistened with a standard head cleaner sold in the market. Never use organic solvents such as thinners to clean the inside parts: Do no use organic solvent like thinner. Japan Cash Machine Co., Ltd. Class EBA-10-SD2 Chapter 2(4) Date Dwg No Page 6
8 7 Installation (1) Installing the unit: There are 4 installation holes each on the rear and bottom cover panels of the unit. (2) Replacing the width guides of the bill insertion slot To replace the width guides of the bill insertion slot, remove the screws from the back side of these width guides. Bank notes to accept Between Width min 65mm ~ 78 mm Length min 125mm ~ 170mm Japan Cash Machine Co., Ltd. Class EBA-10-SD2 Chapter 2(4) Date Dwg No Page 7
9 8 Outline of Interface The following 2 types of interfaces can be provided in Validator EBA-1 O-SD2, depending on the ROM. (1) ID-001 interface The ID-001 interface offers parallel interface support for 7 output lines and 3 input lines. The status of the acceptor is output by the ABN, BSY, and STKT output signals. The type of currency received is output by the VED1 to VEND3 and VALID output signals. The acceptor operation can be controlled by the ACK, REJ, and INH input signals. See the attached "Communications Specifications ID-001 for communication specifications. (2) ID-003 interface The ID-003 interface is a 2-way serial interface. You can control the acceptor status and operation of the acceptor and confirm the settings of each function by sending a polling "Status Request" and commands ("Operation command" and "Setting command") from the controller. See the attached "Communications Specifications ID-003" for communication specifications. Japan Cash Machine Co., Ltd. Class EBA-10-SD2 Chapter 2(4) Date Dwg No Page 8
10 9 Input/Output ID-001 interface circuit ID-003 interface circuit circuit for output signal to turn ON the display LED Japan Cash Machine Co., Ltd. Class EBA-10-SD2 Chapter 2(4) Date Dwg No Page 9
11 10 Cabling Japan Cash Machine Co., Ltd. Class EBA-10-SD2 Chapter 2(4) Date Dwg No Page 10
12 12 DIP Switch Setting DIP switch setting (ID-001) You can set the type of currency to be received, the escrow mode, and other functions using the DIP switch settings. DIP switch setting (ID-003) The available DIP switch settings are as follows. Japan Cash Machine Co., Ltd. Class EBA-10-SD2 Chapter 2(4) Date Dwg No Page 13
13
14
15
16
Europe Bill Acceptor EBA xx
Europe Bill Acceptor EBA - 10 - xx CHAPTER 1 Table of Contents & Model Numbers DWG No. 992-11-01-01 Date 97-11 JAPAN CASHMACHINE CO., LTD. Copyright 1997 Japan Cash Machine Co., Ltd. Contents Contents
More informationSYSTEM 600 GENERAL MAINTENANCE AND ADJUSTMENT GUIDE
SYSTEM 600 GENERAL MAINTENANCE AND ADJUSTMENT GUIDE If you follow a routine maintenance schedule your system 600 will give you years of reliable service with a minimum of down time. This guide outlines
More informationST-07 Series. Bill Validators. Operation Manual
ST-07 Series Bill Validators Operation Manual 998-999 CashCode Co. Inc. Contents Page. Overview. 3. Main Parts..... 4 3. Precautions....... 5 4. Banknote Stacking.... 5 5. Banknote Jam....... 6 6. Maintenance..........
More informationSection 6 Bill Validator VMC/Peripheral Communication Specifications
Section 6 Bill Validator VMC/Peripheral Communication Specifications 6.1 Introduction This section defines the communication bytes sent and received between a Bill Validator and the VMC. As defined in
More informationHF2000 HF3000 HF2500 HF3500. Operator s Manual. Seaga Manufacturing, Inc. 700 Seaga Drive Freeport, IL USA
HF2000 HF3000 HF2500 HF3500 Operator s Manual Seaga Manufacturing, Inc. 700 Seaga Drive Freeport, IL USA 61032 www.seagamfg.com The Elite Automatic Series Vendor INTRODUCTION This manual is divided into
More informationJuly P Wide Format Stacker User Guide
July 2009 701P49768 Wide Format Stacker User Guide 2009 Xerox Corporation. All rights reserved. Xerox and the sphere of connectivity design are trademarks of Xerox Corporation in the United States and/or
More informationS-1600 Series Currency Counter Operating Manual. Models S-1600, S-1615 and S-1625 Including "V" Series
S-1600 Series Currency Counter Operating Manual Models S-1600, S-1615 and S-1625 Including "V" Series CONTENTS Introduction 1 Front View Counter Diagram 2 Rear View Counter Diagram 3 Control Panel Overview
More informationModel S-2200 Single Pocket Currency Discriminator Operating Manual
Model S-2200 Single Pocket Currency Discriminator Operating Manual SEMACON MODEL S-2200 SINGLE POCKET CURRENCY DISCRIMINATOR This Operating Manual provides general guidelines for the operation of your
More informationS-1000 Mini Series Currency Counter Operating Manual. Models S-1000, S-1015 and S-1025
S-1000 Mini Series Currency Counter Operating Manual Models S-1000, S-1015 and S-1025 Contents Section Page Introduction 1 Currency Counter Machine Diagrams 2 Control Panel Diagrams And Functions 4 Placing
More informationOwner s Manual Currency Counter
Owner s Manual Currency Counter TABLE OF CONTENTS 1. Product View 1.1. Front and Rear Views 1.2. LED Display/Control Panel 2. Operation 2.1 Getting Started 2.2 Operation Modes 2.3 The Right Way to Load
More informationRook Currency Counter
Rook Currency Counter TM This manual contains important information on safety measures and operational features. Please read it carefully before operating your currency counter and keep it for future reference.
More informationOperation and Service Manual
BillPro TM Bill Acceptor Operation and Service Manual TABLE OF CONTENTS Section : General Information Introduction... Models... For Your Records... Features... After Unpacking... Main Logic Board Assembly...
More informationWELCOME. Standard Change Makers, Inc. Changer Maintenance Overview General Maintenance Guide for Standard Change-Makers Machines
WELCOME Standard Change Makers, Inc. Changer Maintenance Overview - - - General Maintenance Guide for Standard Change-Makers Machines Service Maintenance School Reviewing: The SC System Product Line. The
More informationS-1100 Series Currency Counter Operating Manual. Models S-1100, S-1115 and S-1125
S-1100 Series Currency Counter Operating Manual Models S-1100, S-1115 and S-1125 Contents Section Page Introduction 1 Currency Counter Machine Diagrams 2 Control Panel Diagrams And Functions 4 Placing
More informationVista 2-NT / Vista 3 & Suprema
Vista 2-NT / Vista 3 & Suprema Bill Acceptor Installation Instructions Bill Acceptor Installation (N016387) October 4, 2001 Page 1 of 10 The following instructions will guide you through the installation
More informationTOSHIBA REMOTE RECEIPT PRINTER TRST-A15 SERIES. Maintenance Manual. Document No. SPAA-214-R1. Original Nov., 2007 (Revised ) PRINTED IN SINGAPORE
TOSHIBA REMOTE RECEIPT PRINTER TRST-A15 SERIES Maintenance Manual Original Nov., 2007 (Revised ) Document No. SPAA-214-R1 PRINTED IN SINGAPORE WARNING! Follow all manual instructions. Failure to do so
More informationATTENTION: OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES
NOTE: Do not follow these instructions for Elite Edge. Please see the Elite Edge Instruction section. 1. Turn off and unplug the game. 2. Unlock and open the CPU section, then place something in front
More informationfinancial services applications like Account Opening Kiosks, Currency Exchange Machines, Bitcoin Teller Machines, and Postal Kiosks.
SC Advance SC Advance Description Featuring enhanced recognition technology, faster note-to-note speed, and improved barcode recognition, the MEI SC Advance offers a variety of cashbox options to ensure
More informationCashCode. MSM BackLoad Bill Validator
CashCode MSM BackLoad Bill Validator Operation and Service Manual Part 1. Operation Manual Rev. 1 Part 1. Operation Manual PAGE 1-1 CONTENTS INTRODUCTION... 3 PRODUCT OVERVIEW... 4 DIMENSIONS...9 GENERAL
More informationMA SERIES Owner's Manual
TEC MA-600 Series owners programming Manual TEC Electronic Cash Register MA-600-1 SERIES Owner's Manual FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital
More informationEB-300 / EB-310. Simple Counter with Detection. (Counting/Detecting) SERVICE MANUAL
EB-300 / EB-310 Simple Counter with Detection (Counting/Detecting) SERVICE MANUAL E-Banking Tech Co., Ltd. #A-1104, Digital Empire 11F, 906-1 Gwanyang, Dongan, Anyang, Gyeonggi, Korea 431-060 TEL : 031-8086-7979~83
More informationWarning: This device complies with part 15 of the FCC Rules. Operation is subject to
CR2 www.carnation-inc.com Warning: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2)
More informationHorizontal Belt Stacker
Shipping & Mailing Inserter Horizontal Belt Stacker TM for Relay Systems Operator Guide International English Edition August 1, 2015 Note: This equipment has been tested and found to comply with the limits
More informationCA11 11 Column. Operator s Manual. To Purchase This Item, Visit BMI Gaming LIMITED WARRANTY
LIMITED WARRANTY Seaga warrants to the original purchaser that the equipment is free from defects in material and factory workmanship for a period of one (1) year from date of shipment. Repair or replacement
More information$250 Capacity ChangeMaker Operator s Manual
$250 Capacity ChangeMaker Operator s Manual Rev. 2017.11.17 1 INTRODUCTION Congratulations on the purchase of your new ChangeMaker. This ChangeMaker has been designed to give you many years of dependable
More informationOperational Manual for the HV-X Validator
Operational Manual for the HV-X Validator Document #101-0029 12/26/02 ABOUT THIS MANUAL This manual will enable the operator to complete basic maintenance, identify error codes, and perform basic troubleshooting.
More informationMagPro TM Bill Acceptor Operation and Service Manual TABLE OF CONTENTS Section 1: General Information Introduction 4 Models 4 For Your Records 4 Features 4 After Unpacking 4 Main Logic Board Assembly
More informationMoving money forward UV MG
Moving money forward T This manual contains important information on safety measures and operational features, please read it carefully before operating your currency counter and keep it for future reference.
More informationUM Owner s Manual
Owner s Manual 2005520UM Currency Counter TABLE OF CONTENTS 1. Product View 1.1. Front and Rear Views 1.2. Control Panel 2. Operation 2.1 Operation Modes 2.2 The Right Way to Load the Bills 3. Troubleshooting
More informationInnovative Technology Limited NV10 Bank Note Validating System. The Future of Smiley Bank Note Handling. Operations Manual GA333-5
Innovative Technology Limited NV10 Bank Note Validating System The Future of Smiley Bank Note Handling Operations Manual GA333-5 Revision History NV10 Operations Manual GA333-5 Innovative Technology Ltd
More informationJCM Company & Product Introduction. 09. Nov. 2011
JCM Company & Product Introduction 09. Nov. 2011 JAPAN CASH MACHINE OVERVIEW PROFILE Established: January 1955 Japan Cash Machine headquarters Tokyo Office, Japan Headquarters: Osaka, Japan Capital: JPY
More informationSnap TM 500 Short Feed
Users Manual Snap TM 500 Short Feed Addendum NEW SHORT FEED NIP ROLLER AVERY DENNISON Manual Edition.2 06 December 200 Manual Part Number 58396 This page intentionally blank Contents Scope 4 Introduction...4
More informationDMC When Accuracy Counts
DMC-1000 Automati c Bi l l Counter When Accuracy Counts Operation Manual 74638 DMC-1000 Automatic Bill Counter Operation Manual Page 3 Index GENERAL 4 PART ONE BASIC INSTRUCTIONS FOR ALL TYPES OF MACHINES
More informationOperating Manual. Professional Weighing Equipment. TB Series intelligent weighing machine. Touch Color Screen HIGH RESOLUTION BALANCE
Professional Weighing Equipment Operating Manual TB Series intelligent weighing machine Touch Color Screen HIGH RESOLUTION BALANCE 1 Introduction What you should know about these Operating Instructions:
More informationOcé DFS10. Operator Manual
Océ DFS10 Operator Manual Océ-Technologies B.V. All rights reserved Id: 7241873 Approvals and certifications Safety Europe Approved by Underwriters Laboratories Inc. North America This equipment is listed
More informationMagner /35-3 Series Currency Counter. Operator's Manual
Magner 35-2003/35-3 Series Currency Counter Operator's Manual Magner 35-2003 / 35-3 Series Introduction. The MAGNER 35-2003 / 35-3 is the most advanced Currency Counter available today. MAGNER's Design
More informationSMARTSCAN 8000 SERIES MUTE MODULES Series Mute Accessories Installation Sheet ( CD174A and CD174B )
SMARTSCAN 8000 SERIES MUTE MODULES 1 8000 Series Mute Accessories Installation Sheet ( CD174A150805 and CD174B080605 ) Unpacking Remove all packaging material and retain it Locate and keep the delivery
More informationF56/F53 Bill Dispenser Unit Maintenance Training Summary
F56/F53 Bill Dispenser Unit Maintenance Training Summary Contents 1, F56/F53 BDU F56/F53 BDU Outline Description 2, D level command / test program 3, Error codes, Maintenance tracking procedure 4, RAS
More informationFirmware Version:1.137 Display Version:2.06a. Xrd-384 Stacker Installation Manual
Firmware Version:1.137 Display Version:2.06a Xrd-384 Stacker Installation Manual 1 Content 1. Safety Precaution 3 2. To use instrument safety 3-4 3. Instruction for use 4 4. Specifications 5 5.Overview
More informationSERVICE MANUAL THEORY OF OPERATION DF Ver. 2.0
SERVICE MANUAL THEORY OF OPERATION DF-601 2004.09 Ver. 2.0 After publication of this service manual, the parts and mechanism may be subject to change for improvement of their performance. Therefore, the
More informationField Installation of Adjustable PAPI Baffles
Field Installation of Adjustable PAPI Baffles Document No. ALN063 Issued: April 18, 1995 Rev. E: June 05, 2009 ADB Copyright 2002 by ADB Airfield Solutions, Incorporated. All rights reserved. Field Installation
More informationSingle Stacker Operational Manual
Single Stacker Operational Manual Document #0-0008 //05 TABLE OF CONTENTS I. INTRODUCTION... 4 Compatibility... 4 Validator... 4 Operation... 4 II. INSTALLATION... 5 Front Load Cabinet... 5 Rear Load Cabinet...
More informationMAGNER START
- Contents Important Safety Precautions... 4 Warning... 4 1. START 1-1. Packing List... 5 1-2. Options... 5 1-3. Appearance... 6 2. BASIC OPERATION 2-1 Self-Diagnosis... 7 2-2. Counting Notes... 8 2-3.
More informationVolume MMF POS. Instruction Manual /User Guide
ENGLISH Volume 1 MMF POS Instruction Manual /User Guide Advantage Series Cash Drawer featuring LockIt - Stop Shrinkage Where it Starts The Advantage Series solution has been engineered to offer a full-size
More informationMODEL BE-100HT HEADSET TELEPHONE OWNER S MANUAL PLEASE READ THIS INSTRUCTION MANUAL CAREFULLY.
MODEL BE-100HT HEADSET TELEPHONE OWNER S MANUAL PLEASE READ THIS INSTRUCTION - 1 - MANUAL CAREFULLY. - 2 - TABLE OF CONTENTS Introduction -------------------------------------------------------------------4
More informationVertical Power Stacker
Shipping & Mailing Inserter Vertical Power Stacker TM for Relay Systems Operator Guide International English Version August 1, 2015 Note: This equipment has been tested and found to comply with the limits
More informationV21 Parts & Service Manual All V21 Identified Equipment REV A 10/2013 P/N: GENERAL INFORMATION. V21 General Information G-1
GENERAL INFORMATION V21 General Information G-1 GENERAL INFORMATION This manual contains programming, operation, and complete parts and electrical wiring diagrams. The V21 controller is a microprocessor
More informationInstallation. Smart-UPS VT in Parallel kva 380/400/415 V 208/220 V 200/208 V
Installation Smart-UPS VT in Parallel 10-40 kva 380/400/415 V 208/220 V 200/208 V Contents Safety... 1 IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS.............................. 1 Prepare for
More informationAP5K-C Precision AC Double-Pulse Spot Welding Machine User s Manual Shenzhen Will-Best Electronics Co., Ltd
AP5K-C Precision AC Double-Pulse Spot Welding Machine User s Manual Shenzhen Will-Best Electronics Co., Ltd 1 Content 1. Introduction...3 1.1 Functions...3 1.2 Units of AP5K-C...4 2. The Initial Installation
More informationCamera Eyepiece. User s Manual. KS035200G4-Ver1.0
Camera Eyepiece User s Manual Content CHAPTER 1 NOTES AND SAFETY REQUIREMENTS ------------------------- - 1-1.1 Cautions and Notes ------------------------------------------------------------------- -
More informationBANKNOTE READER BT-11
English Jofemar BANKNOTE READER BT-11 User s Manual MNP85ENV00 Rev.02 (2014-01-07) Page 1 of 20 Note WARNING Read these instructions carefully before using the appliance: This symbol means there are more
More informationIntroduction to APG Cash Drawers. Cash Drawer Accessories. APG Integration Products. APG Interfaces
APG Products 101 Introduction to APG Cash Drawers Cash Drawer Accessories APG Integration Products APG Interfaces APG Cash Drawer Product Durability Product Durability: Good Better Best You can see the
More informationNational Vendors Changetron 2/4 Validator Installation Instructions
National Vendors Changetron 2/4 Validator Installation Instructions Kit Overview This kit is designed to update National Vendors Changetron 2/4 dollar bill changers that use hopper drums to dispense coins.
More informationOperating Manual. Professional Weighing Equipment SCT SERIES Small Counting Scales. SCT 600g SCT 1200g
Professional Weighing Equipment SCT SERIES Small Counting Scales SMALL COUNTING SCALE WITH CHECK-WEIGHING FUNCTION Operating Manual SCT 600g SCT 1200g 1 Declaration of Conformity Declaration of conformity
More informationProfessional Weighing Equipment. Wheelchair Scale. Operating Manual LWC 800
Professional Weighing Equipment Wheelchair Scale Operating Manual LWC 800 Declaration of Conformity Declaration of conformity for apparatus with CE mark: We hereby declare that the product to which this
More informationRoyal Sovereign RSL 2701 Laminator
Royal Sovereign RSL 2701 Laminator Instruction Manual Provided By http://www.mybinding.com http://www.mybindingblog.com TABLE OF CONTENTS Introduction -----------------------------------------------------------------------------------
More informationOperational Manual. Spectrophotometer Model: SP-830 PLUS. Metertech Inc. Version 1.07
Operational Manual Spectrophotometer Model: SP-830 PLUS Metertech Inc. Version 1.07 Metertech Inc. provides this publication as is without warranty of any kind, either express or implied, including, but
More informationConversion Station Model 711
Conversion Station Model 711 Automatic Tag Dispenser Guide 3M Library Systems 3M Center, Building 225-4N-14 St. Paul, Minnesota 55144-1000 www.3m.com/library Copyright 2000-2004, 3M IPC. All rights reserved.
More informationDESIGNERS AND BUILDERS OF CURRENCY CHANGERS AND ALLIED SYSTEMS SINCE 1921 FOR RLC-2 / RLC-3. Manual Part No Revision No.
DESIGNERS AND BUILDERS OF CURRENCY CHANGERS AND ALLIED SYSTEMS SINCE 1921 SERVICE & PARTS MANUAL FOR RL-2 / RL-3 & RLC-2 / RLC-3 Manual Part No. 95-0011 04-27-00 Revision No. 001 RL-2/RL-3 & RLC-2/RLC-3
More informationFour Stacker Card Dispenser
SPECIFICATION A 1 OF 32 2008. 08.18. KYT-46XXSeries Four Stacker Card Dispenser KYTronics Corp., Ltd. 3rd Floor, A-Dong, Twins Town-Bldg, 703-2, Gojan-Dong,Danwon-Gu, Ansan-City, KyungKi-Do, Korea Tel:
More informationHST -B Interlocking device (Translation of Original Manual)
Installation and Operating Manual for Components HST -B Interlocking device (Translation of Original Manual) HST-B Ident.-No.: 10201 HST-B Ident.-No.: 10207 HST-B Ident.-No.: 10202 HST-B Ident.-No.: 10208
More informationBPS 200. Desktop Banknote Processing System
BPS 200 Desktop Banknote Processing System Cutting costs with the BPS 200 Currency processing costs money Increasing pressure on costs in all areas of cash handling means that new solutions are needed.
More informationSYSTEM 600 BILL CHANGER INSTALLATION INSTRUCTIONS Congratulations...
www.standardchange.com 1-800-968-6955 Technical Phone Support is from 8:00AM to 7:30PM E.S.T., Monday-Friday Walk-in Service is from 8:00AM to 4:30PM E.S.T., Monday-Friday Parts Department is from 8:00AM
More information09/04 Rev MANUAL Jumbo Stacker. Setup, Service
09/04 Rev. 3.00-02 MANUAL Setup, Service General... 2 Intended purpose... 2 Mode of operation... 2 System requirements... 3 Safety notes... 3 Setting up... 4 Positioning the stacker... 4 Setting the material
More informationQUICK REFERENCE GUIDE
QUICK REFERENCE GUIDE i-link QUICK REFERENCE GUIDE i-link Retailer Terminal - HOME SCREEN On the left side of the screen are the Main Terminal Functions. Remember, the main terminal functions that appear
More informationXerox Wide Format Stacker HS
February 2010 701P30730 Xerox Wide Format Stacker HS 2010 Xerox Corporation. All rights reserved. Xerox, the sphere of connectivity design, and Xerox Wide Format Stacker HS, are trademarks of Xerox Corporation
More informationTF20 Tray Feeder. Instruction Manual. for JEDEC and IEC Standard Trays
for JEDEC and IEC Standard Trays Instruction Manual 096-0243-003 Data I/O assumes no liability for errors, or for any incidental, consequential, indirect, or special damages, including, without limitation,
More informationCRT-541 Card Dispenser Machine
CRT-541 Machine Ver 1.0 PRODUCT SPECIFICATION CREATOR (CHINA) TECH CO., LTD. 2F, M-10 Building, Center Area, Hi-tech Industrial Park, Shenzhen Guangdong China TEL:+86 755 26710691 FAX:+86 755 26710105
More informationCutlass Fasteners, Inc. 83 Vermont Ave., Unit 6, Warwick, RI Tel: (401) Fax: (401) cutlass-studwelding.com
MODEL : A-58 ARC WELD GUN PART NO. : 602-378A SERIAL NO. : PLEASE READ THIS OPERATION AND MAINTENANCE MANUAL CAREFULLY BEFORE USING YOUR NEW CUTLASS STUD WELDER. COPYRIGHT CFI 2009 email: sales@ PAGE -
More informationCutlass Fasteners, Inc. 83 Vermont Ave., Unit 6, Warwick, RI Tel: (401) Fax: (401) cutlass-studwelding.com
MODEL : PHM-12 ARC WELD GUN PART NO. : PHM-12 (PHM-12-RS) SERIAL NO. : PLEASE READ THIS OPERATION AND MAINTENANCE MANUAL CAREFULLY BEFORE USING YOUR NEW CUTLASS STUD WELDER. COPYRIGHT CFI 2009 email: sales@
More informationFIRE-RESISTANT PM8 INSTALLATION GUIDE
FIRE-RESISTANT PM8 INSTALLATION GUIDE This installation method will enable you to prepare and easily fit your Plafometal metal ceiling. Please contact us and refer to the Fire Resistance Report prior to
More information2-finger angular gripper SGB 32-50
www.comoso.com Translation of the original manual 2-finger angular gripper SGB 32-50 Assembly and Operating Manual Superior Clamping and Gripping Imprint www.comoso.com Imprint Copyright: This manual remains
More informationQuick Installation Guide. MVC-PTZ-23X Indoor/Outdoor 23 PTZ Speed Dome Camera
MVC-PTZ-23X Indoor/Outdoor 23 PTZ Speed Dome Camera Quick Installation Guide 5101 NW 21st Ave, Suite 210 Fort Lauderdale, FL 33309 www.mace.com (877) 585-6223 Table of Contents 1 QUICK INSTALLATION SPEED
More informationPORTRAIT WARNING HOT GLASS WILL CAUSE BURNS. DO NOT TOUCH GLASS UNTIL COOLED. NEVER ALLOW CHILDREN TO TOUCH GLASS. 569 Ledge Front
PORTRAIT 569 Ledge Front CSA approved for use with Valor Models 530I Heaters ONLY INSTALLATION INSTRUCTIONS! WARNING HOT GLASS WILL CAUSE BURNS. DO NOT TOUCH GLASS UNTIL COOLED. NEVER ALLOW CHILDREN TO
More informationFIRE-RESISTANT ORIAL INSTALLATION GUIDE
FIRE-RESISTANT ORIAL INSTALLATION GUIDE This installation method will enable you to prepare and easily fit your Plafometal metal ceiling. Please contact us and refer to the Fire Resistance Report prior
More informationProduct Information. Pallet change system NSR-A 100
Product Information NSR-A 100 NSR-A Compact. Loadable. Precise. NSR-A Pneumatic pallet change system with patented locking system Field of application For automatic changing of tools such as pallets in
More informationDouble Tidy Rail. Assembly Instructions- Please keep for future reference. Important - Please read these instructions fully before starting assembly
Double Tidy Rail ssembly Instructions- Please keep for future reference 87198 Dimensions Width - 89cm Depth - 8cm Height - 101/17cm Important - Please read these instructions fully before starting assembly
More informationThis product has been tested and certified to conform to ASTM F2456, Youth Resistant Firearms Container.
Owner s Manual This product has been tested and certified to conform to ASTM F2456, Youth Resistant Firearms Container. RAPiD SAFE 2600KP Item No. 98177 Fold out for mounting template This device complies
More informationAutomatic Key Cutting MachineCONDOR XC-MINI CONDOR. Automatic Key Cutting Machine XC-MINI. User Manual
CONDOR Automatic Key Cutting Machine XC-MINI User Manual TABLE OF CONTENTS 1)SAFETY PRECAUTIONS AND WARNINGS ------------------------------------------02 2)GENERAL INFORMATION --------------------------------------------------------03
More informationVolume MMF POS. Instruction Manual /User Guide
ENGLISH Volume 1 MMF POS Instruction Manual /User Guide Advantage Series User Manual A cash drawer designed to provide an advantage over security, quality, and functionality concerns. The Advantage Series
More informationOwner s Manual PCD-42
PCD-42 Owner s Manual Take the time to read through this owner s manual. Familiarity with installation and operation procedures will help you obtain the best Performance from your new CD-receiver. Page
More informationZX70 & ZX80 SERIES PRECISION DECADE RESISTANCE BOX
ZX70 & ZX80 SERIES PRECISION DECADE RESISTANCE BOX OPERATING INSTRUCTIONS SUBJECT TO CHANGE WITHOUT NOTICE This manual superseded all previous versions please keep for future reference TINSLEY, A DIVISION
More informationThank you for purchasing the SC-CONVERSION System 500/600 Conversion Kit. This Kit is available in two different versions:
Rev. 1 (Jun 30, 2016) Thank you for purchasing the SC-CONVERSION System 500/600 Conversion Kit. This Kit is available in two different versions: Part # 4K01328-FI SC-CONVERSION Conversion Kit with MEI
More informationSystem messages (Cash Devices)
System messages (Cash Devices) CSC-W32 V2.1/20 User manual Questions and suggestions Do you have...... any questions or suggestions regarding... any technical questions or problems? this manual? Please
More information(12) United States Patent (10) Patent No.: US 6,896,116 B2
USOO6896.116B2 (12) United States Patent (10) Patent No.: Deaville et al. (45) Date of Patent: May 24, 2005 (54) BILL ACCEPTOR 5,411.249 A 5/1995 Zouzoulas... 271/181 5,630,755 A * 5/1997 Walsh et al....
More informationCOLD SOLVENT CLEANING AND STRIPPING OPERATIONS (Adopted & Effective 5/23/07) (2) Any cleaning of application equipment is not subject to this rule.
RULE 67.6.1 COLD SOLVENT CLEANING AND STRIPPING OPERATIONS (Adopted & Effective 5/23/07) (a) APPLICABILITY (1) Except as provided in Section (b), this rule is applicable to all cold solvent cleaning and
More informationDynatronics Parallel Bars
Dynatronics Parallel Bars Operation & Service Manual For: Electric Height & Width Parallel Bars Electric Height Parallel Bars Platform Parallel Bars Folding Parallel Bars Dynatronics Corporation Dynatronics
More informationFW66 FORESTRY WINCH FW66. Owner s Manual 19/02/2016
FW66 FORESTRY WINCH FW66 19/02/2016 Owner s Manual TABLE OF CONTENTS INTRODUCTION ---------------------------------------------------------------------------------- 2 INTENDED USE -----------------------------------------------------------------------------------
More informationAutomatic Key Cutting Machine - CONDOR XC-007 CONDOR. Automatic Key Cutting Machine XC-007. User Manual V1.2
1 CONDOR Automatic Key Cutting Machine XC-007 User Manual V1.2 2 Table of Contents 1) Safety Precautions and Warnings --------------------------------------------3 2) General Information -------------------------------------------------------4
More informationBike Fixtation LLC th Ave S, Unit 1 Minneapolis, MN Phone:
Bike Fixtation LLC 2647 37th Ave S, Unit 1 Minneapolis, MN 55406 Phone: 612-568-3494 Email: sales@bikefixtation.com 1 Installation Figure: Showing mounting height and electrical hookup location 1. Identify
More informationThe frame elements, accessories and additional elements are maintenance-free!
FULLWHITE MANUAL GENERAL QUALITY AND SAFETY: This projection screen is in accordance with the safety regulations in DIN standard 19045. The screen fabric is comply with DIN 4102 part 1 and the specifications
More informationWelding & Fabrication Tools Mini VaR Tool Kit
With Volta Tools You Can Never Go Wrong! Fast and simple belt installation. Unique and versatile design - compact, rugged and easy-to-use. Designed for both shop and field use. Light-weight construction.
More informationSCR Advance. SCR Advance. Description. Benefits
SCR Advance SCR Advance Description Stemming from its roots in Gaming, having the ability to facilitate payout in banknotes, instead of coins, just makes sense. Eliminating hopper starvation improves machine
More informationGlide-Line Standard Lift Locate Unit (SLLU)
V1.0 Glide-Line Standard Lift Locate Unit (SLLU) Installation & Maintenance Manual Easy Flexible Precise Fast i V1.0 Manual Information Throughout this manual are the following information blocks indicated
More informationUniversal Tactical Light
M2 Universal Tactical Light Operator s Manual MADE IN THE USA WARNINGS 1. Before handling the firearm or the M2 UTL, read and understand the entire contents of the firearm and M2 UTL Operator s Manuals,
More informationStacker 1000 Operator Manual 701P98048
Stacker 1000 Operator Manual 701P98048 Welcome! Congratulations on acquiring the Stacker 1000. Team looks forward to supporting you and helping you increase your organizational productivity. The integrated
More information78-RK VARIABLE SPEED HEAVY DUTY VIBRATOR OPERATING MANUAL
78-RK VARIABLE SPEED HEAVY DUTY VIBRATOR OPERATING MANUAL IMPORTANT INSTRUCTIONS WARNING! FOR YOUR SAFETY PLEASE READ INSTRUCTIONS BEFORE OPERATING TOOL & WEAR EYE PROTECTION FD.08/2009 THANK YOU FOR PURCHASING
More informationnual k Excella E-1 Open Air Shaker N) manual New Brunswick Excella E-1 Open Air Shaker Operating manual
nual k Excella E-1 Open Air Shaker N) manual New Brunswick Excella E-1 Open Air Shaker Operating manual Copyright 2014 Eppendorf AG, Germany. No part of this publication may be reproduced without the prior
More informationVENDING MACHINE CONTENTS CHAPTER 1 QUICK INSTRUCTION... 2 CHAPTER 2 CAUTIONS... 4 CHAPTER 3 DESCRIPTIONS OF VENDING MACHINE... 5
CONTENTS CHAPTER 1 QUICK INSTRUCTION... 2 1.1 PRE-USE PRELIMINARIES... 2 1.2 CUSTOMER S OPERATION GUIDE... 2 CHAPTER 2 CAUTIONS... 4 CHAPTER 3 DESCRIPTIONS OF VENDING MACHINE... 5 3.1. SPECIFICATIONS AND
More informationWAKE UP DESCRIPTION ORDERING INFORMATION SAFETY: WARNINGS T01-E INSTALLATION INSTRUCTIONS MIRRORS K-13013T/K-13014T/K-13015T
WAKE UP INSTALLATION INSTRUCTIONS MIRRORS K-303T/K-304T/K-305T BEFORE YOU BEGIN Warning! Risk of personal injury and product damage. Mirrored cabinets are very heavy and should not be lifted or installed
More information