INFORMATION AND PROCEDURES FOR OBTAINING AN ASME CERTIFICATE OF ACCREDITATION AS AN AUTHORIZED INSPECTION AGENCY

Transcription

1 Two Park Avenue New York, NY U.S.A. tel fax www. asme.org INFORMATION AND PROCEDURES FOR OBTAINING AN ASME CERTIFICATE OF ACCREDITATION AS AN AUTHORIZED INSPECTION AGENCY The Standard for Qualification for Authorized Inspection, ASME QAI-1, requires that ASME Authorized Inspection Agencies shall obtain a valid ASME Certificate of Accreditation In order to obtain the Certificate of Accreditation, the Applicant must demonstrate their compliance with ASME QAI-1. Compliance will be verified by an ASME Survey Team at location(s) which control the activity. The survey will be scheduled by mutual agreement with the Applicant and will consist of a review of the Applicant's rules for compliance with QAI-1 and its implementation. The Quality Manual and documentation which support understanding of the program must be in English. Any findings noted during the survey, are discussed between the Applicant and the Team, and subsequently the Team Report is submitted to ASME which either authorizes issuance of the Certificate or requests additional actions by the Applicant. The Survey Team consists of two ASME Consultants experienced in the field of quality assurance. The "Guide for ASME Survey Teams for Accreditation of Authorized Inspection Agencies " provides a checklist of the elements of a Quality Control System. The Applicant is required to indicate the corresponding cross references to the provisions in the Quality Control Manual which address these elements. The completed Guide must be provided by the Applicant to the ASME Survey Team. A fee is charged based on length of time of survey, including travel time, and travel expenses. This could range from $13,000 to $30,000 for North America and $25,000 to $55,000 for International. In addition, there will be a $3,000 three year Certificate fee. Prices are subject to change without notice. Please bear in mind that the fee ranges quoted are based on typical average surveys and that your survey could require more or less time. These estimates are not firm quotations. If your facility requires an extended survey, because of its complexity, the ranges could be exceeded. The Survey Team will make every effort to conclude their visit in a minimum length of time. The Applicant must at the time of the survey present to the Team Leader commission card(s) from the National Board of Boiler and Pressure Vessel Inspectors showing the inspector is employed by the organization whose name the Applicant wishes to appear on their Certificate of Accreditation. ASME will only issue the Certificate of Accreditation to the organization whose name appears on the AI/AIS commission card(s). If the Applicant is delegating part or all of the functions to an agent organization, then both the Applicant and the delegated organization should be represented during the survey. At the conclusion of the survey, ASME will submit an invoice for the balance of the fees and expenses of the ASME Consultants and the ASME administrative expenses. The invoice will include the Certificate fee if accreditation is recommended. The Certificate will be issued upon successful evaluation by the Subcommittee and receipt of your payment. A12.2-2/14 (1/2)LH

2 ASME requires an advanced deposit of $10,000 prior to establishment of survey dates. This deposit will be applied to the cost of the Survey. If the Applicant withdraws their application after the remittance is received by ASME, there is an administrative fee of $500, which will be deducted from the original remittance. This program includes a planned audit program. Accredited Organizations will be required as a condition of continuation of accreditation to accept audits as required by the QAI Subcommittee on Accreditation, including submittal of a deposit and acceptance of all fees involved in the audit. New Certificate Holders will require an audit approximately one year after issuance of their Certificate. Please submit the application through CA Connect. Jurisdictional Applicants must include as part of their application the completed Supplemental Accreditation Agreement for Jurisdictional AIAs. All new Applicants must include as part of their application the completed Form Supplemental Information for New Applicants. Please return the completed Accreditation/Certification Agreement, fees and required forms to: ASME Accreditation/Certification Processing Dept. 22 Law Drive P.O. Box 2900 Fairfield, NJ In addition, it is requested that the Accreditation/Certification Agreement and forms be ed to ca@asme.org. Cancellation of survey dates is subject to a monetary penalty as shown in the following schedule: $ 2,000 for cancellation after acceptance of the survey dates. $ 3,500 for cancellation within 2 months of the survey dates. $ 6,000 for cancellation within 1 month of the survey dates. In addition to the above, the Applicant will be charged for any committed travel and miscellaneous expenses associated with the scheduled survey. ASME will make every effort to conduct an evaluation of an Applicant's program at the earliest possible date after receipt of application forms and deposit. However, it should be expected that a lead time of four months is usual because of scheduled surveys of other companies. ASME can accept no liability for any consequences to the Applicant which may be the result of the survey or subsequent ASME actions. A renewal survey will be scheduled approximately two to three months prior to the current expiration date to assure continuity of the Certificate. Subscription to ASME QAI-1 is required for accreditation to assure that accredited organizations have the latest applicable rules. Also required is a subscription to all BPV Code Sections that are to be covered in the scope of the Certificate and other ASME Standards required for those sections as shown, in the brochure. Effective with the issuance of the 2007 Edition of the Boiler and Pressure Vessel Code, the electronic version, purchased from a licensed reseller is acceptable, as well as the published version by ASME. The rules published in the Standard and BPV Code Sections are subject to revision periodically and become mandatory six months after the date of publication. Additionally, interpretations of the rules are published in supplements to the Standard and BPV Code Sections. These addenda and supplements are provided to subscribers, as part of their basic subscription, to assure their awareness of the latest rules, revisions and interpretations. Reproduced documents from any source are not accepted for ASME accreditation, as they provide no assurance of completeness or that the user will be made aware of revisions and interpretations of the applicable Standard. If you have any questions, please contact the ASME Conformity Assessment Department via ca@asme.org. A12.2-2/14 (2/2)

3 Two Park Avenue, New York, NY ASME Application for Accreditation/Certification Company: (Company name as it will appear on the Certificate) Division: (Division, department, etc., if it is to appear on the Certificate) This application is for the following location: Address: (Give full address) City State Country Postal code Plant New If renewal, complete the following: Field Site Renewal Current Certificate Number(s): Expiration date: Check the Certificate(s) being applied for: *N Nuclear *N3 Transportation/Storage RTP Reinforced Thermoset *NA Nuclear Assembly Containers Plastic Vessels *NPT Nuclear Partials NO Nuclear Owner QEI Qualification of Elevator *NV Nuclear Safety Valves MO Material Organization, Inspectors *NS Nuclear Supports AIA Authorized Inspection BPE BioProcessing Equipment Agency NQA-1 Nuclear Quality Assurance Stamps ASME is switching to a Single Certification Mark. If you are renewing an existing certificate you will be asked to return your Code Symbol Stamp by no later than January 1, For detailed information about the switch to Single Certification Mark please review the FAQ s on New ASME Mark on our website Please indicate below the number of stamps of each size you would like to receive. If you currently hold stamps you may request an equal number of new certification stamps at no charge. Stamps exceeding the number you currently hold will be subject of the standard stamp fee, as will all stamps accompanying new certificate issuances Number of Stamps Requested: ½ ¾ * Important: If marked with an * you must complete the following: The Authorized Inspection Agency performing our Code inspection is Application must be signed on page A9.54-2/14 (1/2) LH Page 1 of 2

4 Company Abbreviation: Please indicate if the company chooses to use an abbreviation on the nameplate or in the stamping. Yes No If yes, the abbreviation will consist of Note: A Certificate Holder may use either the company s full name or the above abbreviation on the nameplate or in the stamping. The Certificate Holder must list the company s full name as listed on the ASME Certificate on the ASME Manufacturer s Data Report. Accreditation/Certification Agreement The organization listed on the front of this Application for Accreditation/Certification (the Applicant ) performs or subcontracts the design, fabrication, production, testing, assembly, construction and/or installation of items, or provides a service to the aforementioned activities, at the address given, and makes this application to The American Society of Mechanical Engineers (ASME) for the appropriate Certificate of Accreditation, Certificate of Acceptance, or Certificate of Authorization permitting use of the associated Certification Mark. The Applicant: (1) Agrees to use the Certificate and/or Stamp in accordance with the applicable ASME Code or Standard and supplemental conformity assessment requirements governing this application. (2) Agrees to return the stamp and/or Certificate anytime ASME may so request, at the time the Applicant discontinues the work covered, or at the time of expiration, if not renewed. (3) Accepts the conduct of announced or unannounced audits as required by the appropriate ASME accreditation/certification body. Access to the inspection site to conduct audits, reviews or surveys, including travel to and from the site, is the responsibility of the Applicant. If access is blocked or impeded, ASME is not responsible for the Applicant failing to receive, or continue to have accreditation/certification. (4) Agrees to indemnify and hold harmless ASME and its agents from and against any costs (including legal fees and expenses) and any direct, indirect, incidental or consequential damages (including loss of profits or business opportunity) arising out of any claim or cause of action in any way related to this Agreement or the subject matter hereof, including but not limited to claims based on contract, tort (including negligence), strict liability or breach of warranty (express or implied). (5) Understands that the Applicant s use of the ASME mark may be allowed provisionally by ASME in its discretion until a decision is made on an appeal of an action of an ASME subcommittee, committee or board and accepts the obligation to pay all legal fees and expenses and ASME's cost for recovering the Certificate and stamp if not returned. (6) Agrees to pay ASME for all fees, expenses and expenditures associated with the Review/Survey/Audit conducted by ASME. Legal Company Name: Signed: Title: Signature must be by a Company Officer or Designee Date: A9.54-2/14 (2/2) Page 2 of 2

5 Two Park Avenue, New York, NY Form D Company: (Company name as it will appear on the Certificate) Division: (Division, department, etc., if it is to appear on the Certificate) Location (provide full address): Corporate/Mailing Plant Field Site Contact name: Fax: Title: Telephone: Company Website: Jurisdictional Authority (if applicable): Authorized Inspection Agency of record (if applicable): Recommended hotel or motel for team (provide name, full address, and telephone numbers): First choice Second choice Recommended airport (include city name): Miles from airport to lodging: Miles from lodging to office/plant/site: Recommended airport to lodging transfer: Taxi Signed: Limo Hotel provided limo Title: Rent car Pickup by company Date: A4.7-3/13 Page 1 of 1

6 Two Park Avenue, New York, NY Form G (Company Name as it will appear on the Certificate) (Department, Division, etc.) Please list below the location(s) where the survey is to be conducted and at which there is documented evidence to demonstrate implementation of the program to be accredited. Office or Field Site Office or Field Site Telephone: ( ) Telephone: ( ) Contact Name: Contact Name: Title: Title: Office or Field Site Office or Field Site Telephone: ( ) Telephone: ( ) Contact Name: Contact Name: Title: Title: Check Applicable Code Sections: (Note: Use Additional Forms as Needed) I VIII Div. 2 III Div. 1 VIII Div. 3 Signed: III Div. 2 X III Div. 3 XI Title: IV XII VIII Div. 1 Date: A12.1-1/13

7 Two Park Avenue New York, NY U.S.A. tel fax SCHEDULING INFORMATION NEW/RENEWAL APPLICANTS ASME will make every effort to conduct an evaluation of an Applicant's program at the earliest possible date after receipt of the application forms and fees. However, there is an average lead time to schedule surveys, from receipt of completed application and fees of four months due to scheduled surveys of other companies. To minimize costs for Applicants, ASME tries to schedule a series of surveys in the same area of the world. Therefore, in order for ASME to schedule your survey, please answer the following two questions. Please note that if you check as soon as possible for Question 1, or a date much earlier than four months, we will in general only be able to schedule at those times, if another company in your area cancels their date. Question 1 What is the earliest date that you are available for a survey? {Note: Renewal surveys are required to be scheduled approximately 8-12 weeks prior to the current expiration date.} As soon as possible, or Question 2 What weeks or dates are not acceptable to you (due to Holidays, plant shutdowns, etc.) between your first available date and eight months from the date of your application? Company Signature: Date: Your survey will be scheduled at the earliest possible date consistent with your responses and in conjunction with other companies in your area. We, therefore, expect you to accept the dates that we assign. Lack of acceptance may result in a long delay until the next series of surveys are scheduled in your area or a substantial increase in your costs if a Team must be sent to do your survey alone. We cannot schedule your survey until the completed application, fees and this completed form are received. ASME Conformity Assessment Department A4.14E2-1/13(1/1)

8 Supplemental Accreditation Agreement For Jurisdictional AIAs This Supplemental Accreditation Agreement is required to be competed by Applicants for Authorized Inspection Agency (AIA) Accreditation that are Jurisdictions as defined in the ASME QAI 1 Standard. The Jurisdiction applying for accreditation must indicate whether they accept the following principles inherent in QAI 1. Responses marked with an asterisk (*) require an explanation, which must be signed and included with this Supplemental Agreement. 1 Reciprocity The Enforcement Authority (Jurisdiction) agrees to accept the results of inspections required by the ASME Boiler and Pressure Vessel Code which have been performed by an ASME accredited AIA as fulfilling ASME Code requirements for inspection. [ ] Accepted [ ] Accepted in principle, not fully implemented* [ ] Not accepted* 2 Integrity The AIA maintains a commitment to the integrity of the inspection process and of the ASME Code Symbol Marks, by fulfilling its obligations under the ASME Boiler and Pressure Vessel Code and by recognizing the role of the third party inspection system. [ ] Accepted [ ] Accepted in principle, not fully implemented* [ ] Not accepted* 3 Openness The Enforcement Authority (Jurisdiction) permits ASME Certificate Holders and Applicants for ASME Certificates of Authorization located within its Jurisdiction to select other ASME accredited AIAs. [ ] Accepted [ ] Accepted in principle, not fully implemented* [ ] Not accepted* 4 Participation in the process The AIA agrees to participate in the development of the ASME Boiler and Pressure Vessel Code by becoming a member of the Conference Committee or the International Interest Review Group (IIRG). [ ] Accepted [ ] Accepted in principle, not fully implemented* [ ] Not accepted* Signed: Date: (Signature must be by officer or designee of Jurisdiction) Jurisdiction: Title: A /05

9 Two Park Avenue New York, NY U.S.A. tel fax Supplemental Information for New Applicants To be filled out by all Applicants for New Accreditation (not Renewals) Use additional sheets if necessary Organization: Type of Organization QAI References Complete Section: Jurisdictional Authority Insurance Company Independent Third-Party Inspection Organization (a), (a), (a), (a) (b), (b), (b), (b) (c), (c), (c), (c) Jurisdictional Authorities 1.1 What is the designation of the law or regulation which documents that the jurisdiction accepts and administers one or more construction code sections of the ASME Boiler and Pressure Vessel Code? Attach documentation. 1.2 What section(s) of the Code does the jurisdiction accept and administer? Section I Power Boilers Section IV Heating Boilers Section VIII Pressure Vessels Section X Fiber Reinforced Plastic Pressure Vessels Section XII Transport Tanks 1.3 Does the jurisdiction delegate administrative authority to one or more organizations to act on its behalf? Yes complete 1.4 No 1

10 1.4 How is the delegation of authority duly authorized by the laws of the jurisdiction? Attached documentation. 2 Insurance Companies 2.1 Is the company structured with separate organizations/operations of insurance and inspection activities? If yes, how is the relationship defined to jointly meet accreditation criteria? 2.2 List at least one state of the United States or province of Canada that the insurance company is registered by to write boiler and pressure vessel insurance. Attach documentation. 3 Independent Third-Party Inspection Organizations 3.1 By what governmental regulatory body is the organization authorized to perform inspection and/or design review of boilers and/or pressure vessels? Attach documentation. 3.2 How has the governmental regulatory body identified in 3.1 been given the responsibility for the enforcement of regulations pertaining to boilers and pressure vessels? Attach documentation. 3.3 How has the applicant s ability to perform inspections and design reviews for boilers and/or pressure vessels been recognized by the governmental regulatory body identified in 3.1? Attach documentation. 2

11 ASME Boiler and Pressure Vessel Code A N I N T E R N A T I O N A L C O D E Invoice Request Form go.asme.org/bpvc13

12 Invoice Request Form: Please complete the following Invoice Request Form; and then send to: ASME Customer Care 22 Law Drive, Box 2300 Fairfield NJ USA Phone: (toll-free), (Monday through Friday, 8:00 a.m.-5:30 p.m., EST) Fax: (24 hours / 7 days) customercare@asme.org ASME Customer Care then will send you a Proforma invoice with applicable sales tax and shipping / handling charges. Ordering information for domestic and international orders may be found below. Prices are subject to change without notice. ASME Account No. (if Available): Ship To: Company NAME: Address: City / STATE / ZiP Or POSTAl Code: Country: TO ThE ATTENTiON OF: Phone: BILL To: Company NAME: Address: City / STATE / ZiP Or POSTAl Code: Country: Phone: TO ThE ATTENTiON OF:

13 ASME s Boiler and Pressure Vessel Code (BPVC) 2013 Sections Publications: order No. isbn Quantity List Price (USD) line Total BPVC-2013 Sections: I, Rules for Construction of Power Boilers $ II, Materials: II-A, Ferrous Material Specifications (two volumes) 60002A $ II-B, Nonferrous Material Specifications 60002B $ II-C, Specifications for Welding Rods, Electrodes, and Filler Metals 60002C $ II-D, Properties (Customary) 60002D $ II-D, Properties (Metric) 6002DM $ III, Rules for Construction of Nuclear Facility Components: III-NCA, General Requirements for Division 1 and Division R $ Division 1: III-NB, Class 1 Components 60003B $ III-NC, Class 2 Components 60003C $ III-ND, Class 3 Components 60003D $ III-NE, Class MC Components 60003E $ III-NF, Supports 60003F $ III-NG, Core Support Structures 60003G $ III-NH, Class 1 Components in Elevated Temperature Service 60003H $ III Appendices 60003A $ Division 2: III-2, Code for Concrete Containments $ Division 3: III-3, Containments for Transportation and Storage of Spent Nuclear Fuel and High Level Radioactive Material and Waste $ Division 5: III-5, High Temperature Reactors $ IV, Rules for Construction of Heating Boilers $ V, Nondestructive Examination $ VI, Recommended Rules for the Care and Operation of Heating Boilers $ VII, Recommended Guidelines for the Care of Power Boilers $ VIII, Rules for Construction of Pressure Vessels: VIII-1, Division $ VIII-2, Division 2, Alternative Rules $ VIII-3, Division 3, Alternative Rules for Construction of High Pressure vessels $ IX, Welding and Brazing Qualifications $ X, Fiber-Reinforced Plastic Pressure Vessels $ XI, Rules for Inservice Inspection of Nuclear Power Plant Components $ XII, Rules for Construction and Continued Service of Transport Tanks $ Code Cases: Boilers and Pressure vessels * $ Code Cases: Nuclear Components 60012N* $ Binder with Label $20.00 Complete BPVC-2013 (approx. 10% discount off Suggested List Price) 6X $12, Complete BPVC 2013 with 34 Binders 6X $13, ASME Customer Care then will send you a Proforma invoice with applicable sales tax and shipping / handling charges. SUBTOTAL: *Codes Cases are issued four times per year. This price reflects inclusive purchase of all Code Cases issued during the upcoming, two-year publishing cycle for BPVC However, individual Code Cases are also available for separate purchase. Visit or contact ASME Customer Care for details.

14 Product Certification Packages List prices indicated in the following Product Certification Packages include pertinent publications of the 2010 Edition of ASME s Boiler & Pressure vessel Code (BPVC). Upon official publication of the 2013 Edition of the BPVC on July 1, 2013, list prices of these Product Certification Packages will be revised accordingly. Please contact ASME CustomerCare for any questions. Publications: order No. Quantity List Price (USD) line Total Product Certification Packages per Designator : A (Assembly of Power Boilers) BPVCB $2, E (Electric Boilers) BPVCE $2, H (Cast Iron Section Heating Boilers) BPVCH2 $ H (Field Assembly of Boilers) BPVCH $1, H (Heating Boilers, Except Cast Iron) BPHLW $3, HLW (Lined Potable Water Heaters) BPHLW $3, HV (Heating Boiler Safety valves) BPVHV $3, M (Miniature Boilers) BPVCM $4, N, NA, NPT, NS (N-Type Certificates of Authorization and Certificates of Accreditation) BPNPT $3, NV (Nuclear Safety and Pressure Relief valves includes BPVC-II-A, Section II, Part A, Ferrous Materials Specifications) BPNVA $3, NV (Nuclear Safety and Pressure Relief valves includes BPVC-II-B, Section II, Part B, Nonferrous Materials Specifications) BPNVB $3, NV (Nuclear Safety and Pressure Relief valves includes BPVC-II-D, Section II, Part D, Properties, Customary or Metric) BPNVD $3, N3 (N-Type Certificates of Authorization and Certificates of Accreditation) PVCN3 $2, QSC (Quality Systems Certificates Material Manufacturers, Material Suppliers) PVCMS - Contact ASME RP (Fiber-Reinforced Plastic vessels) BPVRP $ S (Power Boilers) / PP (Pressure Piping) BPVCA $4, T (Transport Tanks) BPVCT $4, TD (Transport Tanks, Rupture Disc Devices) BPVCTD $3, TV (Transport Tanks, Safety valves) BPVCTV $3, U (Pressure vessels, Division 1) BPVUM $4, UD (Rupture Disc Devices) BPVCUD $4, UM (Miniature Pressure vessels) BPVUM $4, UV (Pressure vessels, Safety valves includes BPVC-VIII-1, Pressure vessels, Division 1) BPUV1 $4, UV (Pressure vessels, Safety valves includes BPVC-VIII-2, Pressure vessels, Division 2) BPUV2 $4, U2 (Pressure vessels, Division 2) BPVU1 $4, UV3 (Pressure vessels, Safety valves) BPUV3 $4, U3 (Pressure vessels, Division 3) BPVU3 $4, V (Boiler Safety valves) BPVCV $3, ASME Customer Care then will send you a Proforma invoice with applicable sales tax and shipping / handling charges. SUBTOTAL: Related ASME Codes and Standards: Publications: order No. isbn Quantity List Price (USD) line Total Official Spanish-language Translations: BPVC-I-2010 Seccion 1, Reglas para la Construccion de Calderas de Energia XS0010* $ B31.8S-2010 Gestión de Integridad de Sistemas de Gasoductos A21410* $95.00 B16 Series on Valves, Fittings, Flanges and Gaskets: B Pipe Flanges and Flanged Fittings: NPS 1/2 through NPS 24 Metric/Inch Standard M01509* $ B Factory-Made Wrought Buttwelding Fittings J10907* $ B Forged Fittings, Socket-Welding and Threaded M01611* $65.00 B valves Flanged, Threaded and Welding End J01809* $ B Large Diameter Steel Flanges: NPS 26 Through NPS 60 Metric/Inch Standard J12911* $115.00

15 Related ASME Codes and Standards (continued): Publications: order No. isbn Quantity List Price (USD) line Total B31 Series on Piping: B Power Piping A05812* $ B Pipeline Transportation Systems for Liquid Hydrocarbons and Other Liquids A03809* $ B Gas Transmission and Distribution Piping Systems A04510* $ B31.8S-2010 Managing System Integrity of Gas Pipelines A45S10* $ B Surface Texture, Surface Roughness, Waviness and Lay A14312* $ BPE-2012 Bioprocessing Equipment A14309* $ CSD Controls and Safety Devices for Automatically Fired Boilers A09112* $93.00 FSS Series: API 579-1/ASME FFS Fitness-For-Service A $ API 579-1/ASME FFS Fitness-For-Service CD Format A164C $ FFS Fitness-for-Service Print and CD Package AX6407 $1, FSS Fitness-For-Service Problem Manual A $ Nuclear: AG Code on Nuclear Air and Gas Treatment A $ N Self-Operated and Power-Operated Safety-Related valves Functional Specification Standard A00084* $35.00 N Nuclear Power Plant Air-Cleaning Units and Components A08502* $75.00 N Testing of Nuclear Air-Treatment Systems A08207* $55.00 N In-Service Testing of Nuclear Air Treatment, Heating, Ventilating, and Air-Conditioning Systems A16507* $39.00 NOG Rules for Construction of Overhead and Gantry Cranes (Top Running Bridge, Multiple Girder) A11910* $ NQA Quality Assurance Program Requirements for Nuclear Facilities A105E $ NUM Rules for Construction of Cranes, Monorails, and Hoists (with Bridge or Trolley or Hoist of the Underhung Type) J14309* $ OM-2009 Operation and Maintenance of Nuclear Power Plants A $ QAI Qualifications for Authorized Inspection J95010* $60.00 QME Qualification of Active Mechanical Equipment Used in Nuclear Power Plants A13607* $95.00 RA-S-2008 Standard for Level 1 / Large Early Release Frequency Probabilistic Risk Assessment for Nuclear Power Plant Applications A $ Pcc Series on Post Construction: PCC Guidelines for Pressure Boundary Bolted Flange Joint Assembly A15010* $89.00 PCC Repair of Pressure Equipment and Piping A17511* $ PCC Inspection Planning Using Risk-Based Methods A16807* $69.00 PTB Series on Pressure Vessels: PTB ASME Section viii division 2 Criteria and Commentary A19509* $ PTB Guide to Life Cycle Management of Pressure Equipment Integrity A19609* $95.00 PTB ASME Section viii division 2 Example Problem Manual A20410* $ PTC Pressure Relief Devices C06108* $95.00 PVHO Safety Standard for Pressure vessels for Human Occupancy A09212* $ RTP Reinforced Thermoset Plastic Corrosion Resistant Equipment J127E1* $ ASME Customer Care then will send you a Proforma invoice with applicable sales tax and shipping / handling charges. SUBTOTAL: *Also available as digital download (single-user PDF.) Visit or contact ASME Customer Care for details.

16 ASME s Boiler and Pressure Vessel Code (BPVC) 2013 For all other ASME programs -- including product / personnel certifications, training & development courses, professional conferences and publications visit: Ordering Information When ordering with your company purchase order, please make sure that your ASME account number, if available, is indicated. This account number can be found on ASME invoices, packing lists and statements. CA, FL, GA, IL, KY, TX and DC purchasers will be invoiced for applicable sales tax. Canadian purchasers will be invoiced 7% GST, unless ASME is furnished with a valid tax exemption certificate. For international funds transfers, please indicate your ASME order number, invoice number, and account number. Failure to indicate your ASME order number, invoice number, and account number may delay shipment considerably. Please be sure to include your bank s wire transfer fees in the total amount submitted. Proforma invoices showing all charges, including shipping / handling charges, will be furnished upon receipt of order. Orders received with payment will be invoiced for shipping / handling charges. ASME s standard shipping / handling charges may be viewed here: International Orders Advance payment is required for all international orders. ASME accepts most major credit cards, including MasterCard, VISA, American Express, Discover and Euro. ASME also accepts checks written in some international currencies. Contact ASME to determine which currencies are acceptable or visit: Prices are subject to change without notice. Two Park Avenue New York, NY U.S.A.