Special Products SPECIAL PRODUCTS SPECIAL PRODUCTS

Transcription

1 Special Products SPECIAL PRODUCTS SPECIAL PRODUCTS

2 Custom Designed Products CROSBY... A NAME THAT ENCOMPASSES YEARS OF ENGINEERING AND MAUFACTURING EXCELLENCE High capacity crane barge McKissick supplied the sheaves for the original vessel Barge s 7,000 ton cranes updated with McKissick sheaves Those who know the name Crosby need no introduction to the significance this name holds within the rigging and lifting industry. It is a name that encompasses years of engineering and manufacturing excellence a legacy founded on the principle of quality without compromise. The Thialf, from Heerema Marine Contractors, is the largest crane ship in the world and Heerema s main deepwater construction vessel (DCV). The Thialf was initially equipped with Crosby McKissick sheaves in In 2014, Heerema Marine Contractors started to refurbish the Thialf crane sheaves. Due to the proven product quality, value-added services and unmatched training that Crosby offers, the Thialf again used Crosby McKissick sheaves to extend its lifetime for another 20 years. While Crosby is a household name for many those who have yet to discover the meaning behind the name need only a brief history to realize that the global achievements associated with Crosby products is a standard of quality, and innovation over the course of the past century. 448 Copyright 2016 The Crosby Group LLC All Rights Reserved

3 Custom Designed Products THE ABILITY TO PROVIDE CUSTOM DESIGNED PRODUCTS HAS ALWAYS BEEN A STRENGTH OF CROSBY Sheaves used in the locks of the Panama Canal Sheaves used to move vessels and gates Roll Forge sheaves produce remarkable performances Whether your need is for a variation of an off the shelf item, or for a special engineered design product, Crosby is your source. The Panama Canal Authority commissioned Crosby to supply several 64.37in./1635mm diameter roll-forged sheaves for a project as part of the Panama Canal Enlargement known as The Third Set of Locks Project. The sheaves are lighter, stronger and more wear-resistant due to our proprietary upset roll-forged process. By combining the experience of our technical support team, our research and development team, our engineering team and our manufacturing team, we are capable of designing and fabricating custom designed products for any special application. SPECIAL PRODUCTS Copyright 2016 The Crosby Group LLC All Rights Reserved 449

4 Innovative Products MANUFACTURING INNOVATIVE PRODUCTS SINCE 1885 Crosby Engine Hook McKissick Fairleader Base McKissick 500 Ton Bridge Crane Block with Duplex Hook Crosby 18 Ton Sorting Hook When you choose Crosby, you choose a trusted partner who is committed to providing you the resources you need to operate with confidence and without compromise. Since 1885, Crosby s first product that has stood the test of time is the Red-U-Bolt. It is still one of the most recognizable products in the material handling industry. Today Crosby continues this legacy by delivering a diverse portfolio of products engineered to exceed the toughest demands of any industry, including land-based / offshore energy, subsea, transportation cargo handling and cell towers. Crosby s product design team will provide your company with innovative, marketable, and manufacture-ready industrial design solutions for your next product. For more information call: 1(800) Copyright 2016 The Crosby Group LLC All Rights Reserved

5 Testing GLOSSARY OF TERMS FOR TESTING AND THIRD PARTY CERTIFICATION American Bureau of Shipping - (ABS) American Bureau of Shipping is a third party certification agency. ABS publishes several guidelines for various lifting applications. Some of the most common lifting guidelines include the following: Guide for Certification of Cranes Requirements for Certification of Construction and Survey of Cargo Gear on Merchant Vessels Guide for the Certification of Drilling Systems (This is not intended to be a complete list of guidelines published by ABS.) A common request is for ABS third party witness of proof test and magnetic particle inspection after proof test. Depending on the type of certification, requirements may include design review, materials testing, non destructive testing, proof load and special packaging. When specifying ABS certification, it is necessary to know to which guideline the product is to be certified (i.e., Guide for Certification of Cranes, etc.). Det Norske Veritas - (DNV) Det Norske Veritas is an independent foundation established in 1864 for safeguarding life, property and the environment. Along with inspection and advisory services, DNV provides the following three types of certification services. Classification - Certification based on DNV Rules or Certification Notes. Statutory Certification - Certification under authority granted by national authorities (i.e., NPD,UK-HSE, Canada, Australia, etc.) according to acts, regulations, statutory instruments given by statutory authorities. Conformity Certification - Certification to client specifications, national standards or recognized codes. Some of the most common DNV certification rules for lifting are: Rules for Certification of Lifting Appliances Certification Notes No Offshore Containers Rules for Classification of Mobile Offshore Units Part 6, Chapter 5. (This is not intended to be a complete list of DNV Rules.) Lifting products may require design review, materials testing, non destructive testing, DNV issued Proof Test Certificate (CG3) and DNV issued Certificate of Conformity (C of C). Type approved products with a Manufacturer s Survey Agreement (MSA), require all the above except: Design Review, DNV issued Proof Test Certificate (CG3) and DNV issued Certificate of Conformity (C of C). For products certified to Specification (Offshore Containers), DNV witnesses proof test and issues their Proof Test Certificate (CG3) and Certificate of Conformity (C of C) to the distributor responsible for building the container set. It is the distributor s responsibility and cost to contact DNV. When specifying DNV certification, always specify one of the three types of services and, if it is a DNV Rule, which Rule is applicable (i.e., Rules for Certification of Lifting Appliances, etc.). American Petroleum Institute - (API) Established in 1919, API writes specifications that are published as aids for the procurement of standardized equipment and materials, as well as instructions to manufacturers of equipment or materials covered by an API specification. Some of the common specifications written by API for Lifting are: Specification for Drilling and Production Hoisting Equipment (API Spec 8C) Specification for Offshore Cranes (API Spec 2C) Specification for Wire Rope (API 9 Spec A) Specification for Quality Programs (API Spec Q1) A standard to which a manufacturer s quality system must comply in order to state that products are manufactured to API requirements, resulting in permission to apply the API monogram. When specifying API, it is necessary to know to which API Specifications the product is to be certified (i.e., Specification for Drilling and Production Hoisting Equipment (API Spec 8C), etc.). Lloyd s Register of Shipping A society established in 1760 and recognized under UK laws to provide third party assurance of compliance to plans, specifications, rules, codes and fitness of use by approving designs, surveys and reports. Lloyd s Register acts on behalf of clients and governments to verify products conform to statutory requirements and provides inspection and advisory services to clients. Some of the most commonly used Lloyd s Register certification types include the following: Code for Lifting Appliances in a Marine Environment Rules and Regulations for the Classification of Ships Rules and Regulations for the Classification of Mobile Offshore Units Container Certification Scheme SPECIAL PRODUCTS Copyright 2016 The Crosby Group LLC All Rights Reserved 451

6 TESTING GLOSSARY OF TERMS FOR TESTING AND THIRD PARTY CERTIFICATION Lloyd s Register of Shipping continued A common request is for Lloyd s Register witness proof test and magnetic particle inspection with certification. However, certification may require design review, material tests or product verification to statutory or customer requirements. When specifying Lloyd s Register of Shipping certification, know the code, standard, statute or customer requirement (i.e., Code for Lifting Appliances in a Marine Environment, etc.). Federal Specifications & Military Standards The Federal Specifications & Military Standards documents specify dimensional, performance and test requirements for products. Some specifications define particular testing that is not normally performed on standard items. Crosby products, when identified in the latest Crosby General Catalog, will meet the requirements when tested by the party awarded the government contract. Certification is usually covered by a Crosby Standard Certificate of Conformance. ISO 9001 A standard defining a manufacturer s or service organization s Quality Management System requiring third party certification. ISO 9001, the most comprehensive ISO certification level, involves the design, development, production and shipping of products. ISO 9001 requires that all procedures, work instructions, processes and additional activities be documented. Attainment of ISO 9001 forms the basis for meeting other world standards and provides customers with documented proof of Crosby s ability to consistently provide product quality and performance. National Association of Chain Manufacturers (NACM) A U.S. Standard specifying dimensional and performance criteria for graded chain. American Society for Testing and Materials (ASTM) American Society for Testing and Materials, established in 1898, is the largest voluntary standards development system in the world. ASTM Standards cover: Inspection Methods (Certificates Required) i.e., Magnetic Particle, Ultrasonic, Dye Penetrant, X-Ray, Hardness, etc. Processes (Standard Certificate of Conformance) i.e., Hot Dip Galvanizing, Electroplate, Mechanical Galvanizing,etc. Material Properties (Tensile Test Report Required) i.e., Specification for Steel Forging, Carbon and Alloy for General Industrial Use (A668), Specification for Steel, Closed-Impression Die Forgings for General Industrial Use (A521), etc. Material Test Methods Covers Tensile and Charpy impact test specimens and test methods, i.e., Test Methods of Tension Testing of Metallic Materials (E8), A370 Test Methods and Definitions for Mechanical Testing of Steel Products (A370), etc. American National Standards Institute (ANSI) American National Standards Institute established in 1916 develops product specific performance standards for items such as cranes, hooks, slings, screw threads, etc., usually covered with a standard Certificate of Conformance. Crosby Standard Testing Upon Request *Crosby Proof Test with Third Party Witness Receive load test certification signed, documented and serial number traceable to these agencies: ABS, DNV, Lloyds, B.V., RINA, Germanischer Lloyd, etc. *Crosby Proof Test with I.L.O. Certificates Standard load test performed and documented on International Labor Organization Form 4 (I.L.O. Form 4). Certified and traceable by serial number. The certificates are maintained at Crosby. *Crosby Standard Certificate of Conformance Part number, description, date and statement of conformity to Crosby literature available at time of manufacture. *Crosby Magnetic Particle Inspection with Certification ASTM E-709 wet or dry method standard at Crosby. Customer can require other types. Certified and traceable to serial number. *Crosby Ultrasonic Inspection with Certification ASTM A-609 for castings, ASTM A-388 for forging standard at CrosbyCustomer can require other types. Certified and traceable to serial number. *Crosby X-Ray with Certification Customer provides x-ray technique and level of acceptance. *Crosby Dye Penetrant Inspection with Certification A liquid penetrant examination to ASTM E-165. Other types of Dye Penetrant certification is available at time of order. Certified and traceable to serial number. *Crosby Material Tensile Test with Certification Tensile test performed per ASTM A370. Test report documents Tensile Strength, Yield Strength, Elongation, and Reduction of Area. *Crosby Material Chemical with Certification Chemical certification provided by steel mill or foundry. Traceable to heat number, heat letters and PIC code. *Crosby Charpy Impact Test with Certification Impact Test per ASTM A370 or ASTM E8 at temperature, location, and energy absorbed requirement as defined by customer or applicable specification. *A charge will be applied. Crosby certification is available when requested at time of order. The items listed above are for standard certification. Additional certification is available and must be requested at time of order. 452 Copyright 2016 The Crosby Group LLC All Rights Reserved

7 Custom Design Hooks Company Name: Address: City, State, Zip Date: Phone: Fax: Country: Customer Contact Name: Quotation Due Date: Crosby / McKissick Proposal Number: CROSBY CUSTOM MACHINED SHANK HOOK & NUT QUOTATION REQUEST FORM Product Delivery Date: Quantity: Dimensions: Frame Size and material Symbol: Working Load Limit (tons) A. Round or Hex Nut B. E.* C.* F. D. * The minimum thread length engaged in the nut should not be less than one (1) thread diameter. For additional information concerning customer design products, contact: In U.S.A. - Crosby s Special Engineered Products Group at In Canada - Crosby Canada at (905) In Europe - N.V. Crosby Europe at (26) Hook Latch Kit SS-4055 Flipper latch PL Flapper latch 4320 Latch SPECIAL PRODUCTS Copyright 2016 The Crosby Group LLC All Rights Reserved 453

8 Custom Split-Nut Hooks ( FOR MOBILE CRANES) Company Name: Date: Address: City, State, Zip Code: Phone: Fax: Country: Customer Contact Name: Quantity: Requested Delivery Date: - INTERNAL USE ONLY - Crosby / McKissick Proposal Number: Crosby McKissick patented (U.S. Patent 7,000,905 and 7,293,763) Split-Nut Hook Retention System featured on McKissick crane blocks makes inspection easier. The hook can be disassembled, inspected and put back into service in a fraction of the time of a conventional threaded nut. 319 Hook Type and Working Load Limit 4:1 Alloy (t) Crosby Hook ID Code A Available Shank Dia. Available Configurations B Dimension C Dimension D Maximum Grip Length (in.) (mm) (in.) (mm) (in.) (mm) (in.) (mm) 15 L N O P S T U W Steps to fit your block with the patented McKissick Split-Nut Hook Retention System 1. Measure side plate to hook tip clearance and record in box G below. (The net length H dimension may be affected by holding the G dimension. If there is adequate clearance at tip of hook, the net length H dimension may be the dimension to specify). 2. Remove hook and thrust bearing from existing crane block. 3. Measure shank diameter and record in box A below. 4. Measure nut thickness and record in box B below. The standard B dimension (shown above) is a minimum and will be utilized unless actual measured B dimension is required. 5. Measure nut diameter and record in box C below. The standard C dimension (shown above) is a minimum and will be utilized. 6. Measure thrust bearing thickness and record in box E below. If known, record thrust bearing manufacturer and stock number below. 7. Measure trunnion thickness through the hook shank hole and record in box F within 1/ The required grip length D will be the addition of the E and F dimensions plus 0.06 for running clearance. 9. Determine the required hook size based on shank diameter and tonnage. Other shank /hook / tonnage combinations may be available. Your supplied information will be reviewed for the Split-Nut application. 10. Complete the form and forward to your local Authorized Distributor for quotation. Required Dimensions Shank Ø Thrust Bearing Standard Bearing Outside Dia. Bearing Thickness (in.) (mm) (in.) (mm) (in.) (mm) Bearing Description T T T T-301-W TP-114 Frame Code or other distinguishable size designator: Material Type: Check One: Carbon Alloy Working Load Limit: Check One: Tons Metric Tonnes Thrust Bearing Identification: Check One: Check One: Hook Latch Kit Check One: Dimension A: Dimension B: (in.) (in.) (mm) (mm) Dimension E: Dimension F: (in.) (in.) (mm) (mm) SS-4055 Flipper latch PL / PL-N Flapper latch S-4320 Latch Dimension C: (in.) (mm) Dimension G: (in.) (mm) Dimension D*: (in.) (mm) Dimension H: (in.) (mm) *D = Bearing Thickness E + Trunnion Thickness F +.06 running clearance. For additional information concerning customer design products, contact: U.S.A. - Crosby s Special Engineered Products Group at Canada - Crosby Canada at (905) Europe - N.V. Crosby Europe at (26) For personnel hoisting applications, only a PL, PL-N or S-4320 shall be utilized. 454 Copyright 2016 The Crosby Group LLC All Rights Reserved

9 Custom Design Hooks McKISSICK DUPLEX HOOK ASSEMBLIES Cast alloy steel. Available in forged steel upon special request. Can be machined to optional dimensions upon request. Furnished complete with two flipper latches. The working load limits shown are in short tons (T) and applicable for loading up to an included sling angle of 90 degrees. For included sling angles up to 60 degrees, the hooks can be rated in metric tons (t). N X 45 B C A D N J K G E F L H O M Stock No. Hook Assembly Duplex Hook with Nut and Latches Dimensions (in.) Weight Each (lbs.) Replacement Latch Kit Stock No. Size (Tons) A B C D E F G H J K L M N O * * Ultimate Load is 4 times the Working Load Limit. * Bolt style latch ton has different prong profile than shown. For the purpose of calculating D/d ratio, utilize dimension O. For additional information concerning custom design products, contact: In U.S.A. Crosby s Special Engineered Products Group at , Fax (918) In Canada Crosby Canada at (905) In Europe N.V. Crosby Europe at (26). SPECIAL PRODUCTS Copyright 2016 The Crosby Group LLC All Rights Reserved 455

10 Bullard Golden Gate Hooks Hook Size: Sales Order: Working Load Limit (Tons) Hoist Name and Model: HOOK DATA FORM Name of Person Completing Form: Telephone: Distributor: Top Hook Bottom Hook Distributor P.O.: Is Self-Closing Gate Required? Yes No Accurate dimensions are important. If you have any questions, contact your authorized Crosby Distributor. Shank Length 1. Measure total USABLE shank length from top of hook shank to top of gate assembly. Gate assembly is not considered part of the USABLE shank. When measuring other manufacturers hooks, measure from the top of the hook shank to the hook shoulder. 2. Measure threaded portion (enter BLANK if threads not required). NOTE: Hook is supplied with Steel Hex-Load Nut and Bronze Load Washer. Hook and Nut threads are National Coarse. If a SPECIAL Load Nut or Load Washer is required, attach a drawing to this form. Shank Diameter 3. Measure width of threaded portion. 4. Measure width of blank portion. Throat Opening 5. ONLY measure throat opening if this distance is critical to customer s operation. Cross Hole in Shank Hooks (complete only if required) 6. Measure shank length from center of hole to top of gate assembly. 7. Measure diameter of hole. Length of Projection Coupler Hook size 11, 12, or 14 may require coupler as shown. Distance Between Plates 456 Copyright 2016 The Crosby Group LLC All Rights Reserved

11 Swivel Hoist Ring Data Form SPECIFICATION SHEET FOR CROSBY HR125, HR125M, HR1000 HOIST RINGS WITH OPTIONAL BOLT LENGTHS Date: CG #: Customer #: Distributor s Name: Distributor s Phone Number: Distributor s P.O. # Crosby Quote Number: Contact: Distributor s Fax Number: Quantity Requested: Crosby Representative: 1. Determine the Type of Threads required on the Hoist Ring - Metric or UNC, UNF, etc. NOTE - NOT DESIGNED FOR PIPE, ACME OR TAPERED THREADS. 2. Determine the Working Load Limit of the requested Hoist Ring. 3. Determine Bolt Diameter - The diameter of the required bolt. 1. Thread Type (Circle One) UNC Thread Metric Thread Other (NOT DESIGNED FOR PIPE, ACME, OR TAPERED THREADS) 2. Hoist Ring Capacity (Working Load Limit) lbs./kgs 4. Determine Effective Thread Length -This is the length the threads must be in order to fully engage, or project through, the work piece. NOTE; If the Effective Thread Length is not known, the Length of Bolt is required. 5. Determine Length of the Bolt - The overall length of the bolt as measured from under the head of the bolt. NOTE: If the Effective Thread Length is not known, the Length of the bolt is required. 6. # of Thread Threads per Inch (Length Between Threads for Metric threads) - This information is required to ensure we ship proper bolt size (i.e., 1/2-13, 7/8-9, 8 x 1.25, etc.). SPECIAL PRODUCTS Copyright 2016 The Crosby Group LLC All Rights Reserved 457

12 Custom Lead Sheaves Company Name: Country: Date: Address: City: State, Zip: Phone: Fax: Country: Customer Contact Name: Quantity: SHEAVE INFORMATION Sheave Diameter: Wire Rope Size: Number of Sheaves: BEARING TYPE Bronze Bushing Roller Bearing Tapered Roller Bearing Other BLOCK INFORMATION Style: Vertical Horizontal Dimensions: A. B. C. D. APPLICATION INFORMATION Line Speed: Single Line Pull: Degree of Wrap: Environment: FREQUENCY OF USE Continuous: Intermittent: One Time: SPECIAL REQUIREMENTS Special Testing: Finish: Third Party Inspection / Approval: (If 3rd Party Inspection or Approval is required, please refer to page Vertical Deck Guide Horizontal Deck Guide 458 Copyright 2016 The Crosby Group LLC All Rights Reserved

13 Custom Lead Blocks Company Name: Country: Date: Address: City: State, Zip: Phone: Fax: Customer Contact Name: Quantity: DIMENSIONAL INFORMATION Nominal Outside Diameter: Wire Rope Size: Rim Width: + Shaft Size: * Hub Width: Nominal Tread Diameter (Optional): + Shaft size is bore size on Plain Bore Sheaves. * Hub width is measured over the cone of the Tapered Bearing Sheaves. Nominal Hub Diameter (Optional): BEARING TYPE Bronze Bushing Ball Bearing Tapered Roller Bearing Roller Bearing (requires hardened and ground shaft) Full Complement Double-Row Cylindrical Roller Bearings with Seals Finish / Plain Bore Underwater Other MATERIAL TYPE Roll Forged (Flame hardened 14 (356mm) and larger) Forged Steel Cast Steel Fabricated APPLICATION INFORMATION Line Pull: Fleet Angle: Domed Other Degree of Wrap: Line Speed: Environment: Groove Angle: SPECIAL REQUIREMENTS Special Testing: Finish: Third Party Inspection / Approval: (If 3rd party inspection or approval is required, please contact Crosby Customer Service.) NOTE: Crosby manufactures sheaves in a wide array of styles and sizes. See page SPECIAL PRODUCTS Copyright 2016 The Crosby Group LLC All Rights Reserved 459

14 Custom Bridge Crane Blocks Company Name: Country: Date: Address: City: State, Zip: Phone: Fax: Customer Contact Name: SHEAVE INFORMATION Sheave Diameter: Wire Rope Size: Number of Sheaves: BEARING TYPE Bronze Bushing Roller Bearing Tapered Roller Bearing Other Quantity: BLOCK INFORMATION Dimensions: A. B. C. D. Working Load Limit: CMAA Rating: LOWER FITTING TYPE Single Point Hook Duplex Hook Swivel Hook Latch Other B A B BLOCK HOTLINE ( ) C E THROAT OPENING APPLICATION INFORMATION Overhaul Weight Requirements: Lead Line Speed: Environment: SPECIAL REQUIREMENTS Special Testing: Finish: Third Party Inspection / Approval: (If 3rd Party Inspection or Approval is required, please refer to page ) Four Position Locking Mechanism Other (Specify) 460 Copyright 2016 The Crosby Group LLC All Rights Reserved

15 High Capacity Snatch Blocks Company Name: Country: Date: Address: City: State, Zip: Phone: Fax: Customer Contact Name: Quantity: SHEAVE INFORMATION Sheave Diameter: Wire Rope Size: Number of Sheaves: BEARING TYPE Bronze Bushing Roller Bearing Tapered Roller Bearing Other BLOCK INFORMATION Working Load Limit: Fitting Type Single Point Hook Shackle Bolt M491 Other Maximum Weight Maximum Length APPLICATION INFORMATION Describe Application: Lead Line Speed: Environment: SPECIAL REQUIREMENTS Special Testing: Finish: Third Party Inspection / Approval: (If 3rd party Inspection or Approval is required, please refer to page ) Other (Specify) SPECIAL PRODUCTS Copyright 2016 The Crosby Group LLC All Rights Reserved 461

16 API 2C Block Systems Material traceability, impact chemistry reports, tensile test reports, magnetic particle inspection per ASTM E-709 on the following components: HOOK, HOOK NUT, HOOK TRUNNION, CENTER PIN, SIDE PLATE, SHEAVE (no MPI or impact on sheave) and DEAD END. Sheave diameter based on D/d ratio based on pitch equal to 18/1. Weight plates produced from plate steel. Design Service Temperature = (standard is 0 C. +32 F) 3rd Party ABS, DNV, etc. Proof test to 2 times the WLL. OVERHAUL BALL REQUIREM Material traceability, chemistry, tensile test, magnetic particle inspection per ASTM E-709 on the following components: SWIVEL EYE, FIXED EYE, SWIVEL BASE, PLUG, CASE PIN, HOOK PIN AND HOOK. Charpy impact tests with reports on HOOK, testing to be performed per API-2C latest revision. Impact test with reports on SWIVEL EYE, FIXED EYE, SWIVEL BASE, PLUG, CASE PIN AND HOOK PIN, testing to be performed per API-2C latest revision. Design Service Temperature = (standard is 0 C. +32 F) 3rd Party ABS, DNV, etc. Proof test to 2 times the WLL. SELECT DESIRED TAG Rating #1: Cv = W.L.L. = (T or mt) with design factor = Rating #2: Cv = W.L.L. = (T or mt) with design factor = Personnel rating = Wire rope size Minimum desired weight Number of sheaves Parts of line = 2 times number of sheaves = Eye to rotate on thrust with grease fitting. Rating #1: Cv = W.L.L. = (T or mt) with design factor = Rating #2: Cv = W.L.L. = (T or mt) with design factor = Personnel rating = Wire rope size Minimum desired weight API-2C BLOCK / BALL API-2C BLOCK / BALL * BLOCK / BALL MEET THE REQUIREMENTS OF API-2C. OR * BLOCK / BALL MEET THE REQUIREMENTS OF API-2C. TO LIFT MEN, USE POSITIVE LOCKING HOOK LATCH PER OSHA (g)(1)(i)(a) & (g)(4)(iv)(b) TO LIFT MEN, USE POSITIVE LOCKING HOOK LATCH PER OSHA (g)(1)(i)(a) & (g)(4)(iv)(b) Material traceability, chemistry, tensile test, magnetic particle inspection per ASTM E-709 on the following components: SOCKET BODY AND PIN. Charpy impact test with reports on SOCKET BODY AND PIN, testing to be performed at per API-2C latest revision. Wire rope size 3rd Party ABS, DNV, etc. 462 Copyright 2016 The Crosby Group LLC All Rights Reserved

17 Custom Swivels Company Name: Address: Date: City: State, Zip: Country: Phone: Fax: Customer Contact Name: Quantity: SWIVEL Angular Contact Bearing Tapered Roller Bearing SWIVEL STYLE Jaw & Hook Eye & Jaw Bullet Jaw & Jaw (ACBS only) Jaw & Jaw Eye & Eye Jaw & Eye Eye & Hook APPLICATION INFORMATION WLL required: Hook Size: FREQUENCY OF USE Continuous: Intermittent: One Time: SPECIAL REQUIREMENTS Special Testing: Finish: Third Party Inspection / Approval: (If 3rd Party Inspection or Approval is required, please refer to page ) Dimensions for Eye A B C D Dimensions for Jaw A B C D E throat opening SPECIAL PRODUCTS Copyright 2016 The Crosby Group LLC All Rights Reserved 463

18 Custom Fairleaders CUSTOM DECK MOUNTED ANCHOR FAIRLEADERS Company Name: Date: Address: City: State, Zip: Phone: Fax: Name: Country: Quantity: SHEAVE INFORMATION Sheave Diameter: Wire Rope Size: Number of Sheaves: 1 or 2 BEARING TYPE- Sheave Bronze Bushing Roller Bearing Tapered Roller Bearing Other BEARING TYPE- Barrel Bronze Bushing Roller Bearing Tapered Roller Bearing Other BLOCK INFORMATION Syle: Pedestal Mount Base Mount Dimensions: A. B. C. D. APPLICATION INFORMATION Lead Line Speed: Single Line Pull: Degree of Wrap: Environment: FREQUENCY OF USE Continuous: Intermittent: One Time: SPECIAL REQUIREMENTS Special Testing: Finish: Third Party Inspection / Approval: (If 3rd Party Inspection or Approval is required, please refer to page ) Base Mount (2 sheave version shown) Pedestal Mount (1 sheave version shown) 464 Copyright 2016 The Crosby Group LLC All Rights Reserved

19 Clamp-Co Pipe Hooks CUSTOM PIPE HOOK FORM Company Name: Country: Date: Address: City: State, Zip: Phone: Fax: Customer Contact Name: Quantity: GENERAL REQUIREMENTS Working Load Limit per pair (weight of load): Handle Required DIMENSIONAL REQUIREMENTS Grip Opening (A): Grip Depth (B): Plate Thickness (C): Shackle Opening (D): SPECIAL REQUIREMENTS Finish: Proof Test Load: MPI UT Third Party Inspection/Approval: SPECIAL PRODUCTS Copyright 2016 The Crosby Group LLC All Rights Reserved 465

20 Approval/Inspection Requirement THIRD PARTY REQUIREMENTS FORM Company Name: Address: City: State, Zip: Date: Phone: Fax: Customer Contact Name: Country: Crosby Proposal Number: Quantity: Equipment Description: Customer P.O.: Type of Application: End Users / Operator: Rig/Vessel Name or I.D.: Geographical Location: REGULATIONS/ CODES/ STANDARDS American Bureau of Shipping Guide for the Classification of Drilling Systems Guide for Certification of Lifting Appliances Guide for Certification of Cranes Det Norske Veritas Standard for Certification No Offshore Containers Standard for Certification No Lifting Appliances Lloyds Register Lifting Appliances in a Marine Environment Other LR API 8C API 2C Other Steel Vessels Rules Offshore Standard DNVGL-OS-E101 Drilling Plant Other Other ABS Rules for Classification: Offshore Units DNVGL-RU-OU-0101 Other: OPERATING CONDITIONS Minimum Design Temperature: Load Conditions: Working Load: EXTENT OF THIRD PARTY INVOLVEMENT: 466 Copyright 2016 The Crosby Group LLC All Rights Reserved