AMPLUS INDUSTRIAL LTD.

Transcription

1 AMPLUS INDUSTRIAL LTD. SWITCHING ADAPTOR SPECIFICATIONS REF No AMPLUS W04159-ADAPTOR Page 1

2 TABLE OF CONTENTS 1. SCOPE 2. SPECIFICATION NUMBER 3. ENVIRONMENTAL REQUIREMENTS 4. INPUT REQUIREMENTS 5. INTRODUCTION 6. DC INSULATION RESISTANCE 7. DIELECTRIC WITHSTAND-VOLTAGE 8. MAIN FUSE 9. INRUSH CURRENT 10. TIME SEQUENCE 11. EFFICIENCY 12. SAFETY STANDA 13. RFI EMISSION 14. OUTPUT RATED & ELECTRICAL SPECIFICATIONS 15. RELIABILITY TESTING 16. MODEL LIST REF No AMPLUS W04159-ADAPTOR Page 2

3 1. SCOPE This document is applied to model of S.M.P.S 2. SPECIFICATION NUMBER AMPLUS part number : Customer part number: AM ENVIRONMENTAL REQUIREMENTS Operating temperature: Storage temperature : Operating humidity : 30% -- 95% Storage humidity : 30% --98% Operating bar : 1BAR 4. INPUT REQUIREMENTS Regular input voltage: AC 100 AC 240V Variable input voltage range : AC 90V AC264V Rating frequency : 50Hz 60Hz Frequency range : 47Hz 63Hz Input current : 0.18Arms MAX (at regular voltage & current) 5. INTRODUCTION The S.M.P.S operated at input regular voltage AC 100V 240V The S.M.P.S should be capable of a total continuous DC power output of 4Watts. The S.M.P.S should be capable of a total peak 7.5 Watts. The S.M.P.S is single output and the voltage can be changed R12. Refer output rated & electrical specifications table The S.M.P.S should not be fired or emitted smoke by protection when the circuit is short. The S.M.P.S design with current limit circuit. The S.M.P.S design with over load protection. REF No AMPLUS W04159-ADAPTOR Page 3

4 6. DC INSULATION RESISTANCE Input Output :50MΩminimum (at 500VDC) Input Body Metal : 50MΩminimum (at 500VDC) 7. DIELECTRIC WITHSTAND - VOLTAGE Input Output : 3750VAC minimum (2S) Input Body Metal : 3750VAC minimum (2S) 8. MAIN FUSE Input fuse is 10 OHM 1W fusible resistor 9. INRUSH CURRENT Peak inrush current shall be limited to 10A for a cold start 10. TIME SEQUENCE Time sequence should be satisfied to power ON/OFF AC switch at ON/OFF AC input 95%V 100%V 95%V DC output 0.5 S 20m S 11. EFFICIENCY The efficiency of the S.M.P.S must be satisfied the minimum 55%. REF No AMPLUS W04159-ADAPTOR Page 4

5 12. SAFETY STANDA To meet EN60950, IEC RFI EMISSION To meet EN55011, FCC PART OUTPUT RATED & ELECTRICAL SPECIFICATIONS RATED OUTPUT (V) Rated current(a) Short output current(a) Max. output voltage(v) Min. output voltage(v) Ripple & Noise(mV) Max Current limit YES YES YES YES YES YES YES YES YES YES Rated power(w) Switch frequency(khz) Insulation class II II II II II II II II II II Consumes(W) <0.2 <0.2 <0.2 <0.2 <0.2 <0.2 <0.2 <0.2 <0.2 <0.2 REF No AMPLUS W04159-ADAPTOR Page 5

6 15. RELIABILITY TESTING A. CO PUSH/PULL TEST OF I/O CONECTOR SIDE NO CUTTING INNER WIRE Test condition: 8kgf X10sec at Y axis; 5kgfX10sec at other 4 direction verticality 5kgfx10s 5kgfx10s 8kgfx10s 5kgfx10s 5kgfx10s B. CO PUSH/PULL TEST OF ADAPTER SIDE NO CUTTING INNER WIRE Test condition: 8kgf X10sec at 5 direction verticality. 8kgfx10s 8kgfx10s 8kgfx10s 8kgfx10s 8kgfx10s C. CO BENDING TEST OF I/O CONECTOR SIDE NO CUTTING INNER WIRE Test condition: =1 cycle, 30 cycle/1min, weight = 200g, from step 1 to step 2 continuously Step cycle for difficult bending direction Step cycle for easy bending direction 60' 60' 60' 60' REF No AMPLUS W04159-ADAPTOR Page 6

7 D. CO BENDING TEST OF ADAPTER SIDE NO CUTTING INNER WIRE Test condition: =1 cycle, 30 cycle/1min, weight = 500g, from step 1 to step 2 continuously Step cycle for difficult bending direction Step cycle for easy bending direction 60' 60' 60' 60' E. BLADE PUSH/PULL TEST BLADE SHOULD NOT BE FAILLEN OUT NO ANY IRREGULLAR CONDITION, SLIGHT BEND AFTER TEST IS ACCEPTABLE Test condition: weight = 10kg, Duration = 60sec, Hold 60 seconds putting the force of push and pull to the tip of blade, then confirm appearance and condition. F. INDIVIDUAL DROP TEST WITHOUT OPENING OF CASE Test condition: 6 face, AND CRACK, etc. each face 1 time 70 cm, ELECTRIC CHARACTERISTIC on the 5mm wooden board SHALL BE SATISFIED. LIGHT CRACK AFTER TEST IS ACCEPTABLE. G. LOW TEMPERATURE STORAGE TEST PASS Keep on -30 (Packing) for 168 hours, and check the action after 3 hours in 25. REF No AMPLUS W04159-ADAPTOR Page 7

8 H. HIGH TEMPERATURE STORAGE TEST PASS Keep on +70 (Packing) for 168 hours, and check the action after 3 hours in 25. I. HIGH HUMIDITY STORAGE TEST PASS Keep on %RH (Packing) for 168 hours, and check the action after 3hour in 25. J. TEMPERATURE CYCLE TEST PASS Keep on -45 (Packing) for 1 hour, then keep on +85 (Packing) for 1 hour Repeat this cycle until 10 cycle, check the action after an hour in 25. K. CURRENT- CARRYING OF HIGH VOLTAGE TEST ANY CASE DEFORMATION, SMOKING, OR BURN BY HEAT SHOULD NOT BE FOUND. Select higher load condition of power consumption at a non-load condition or standard load condition. The test samples shall be active with input voltage is 280V/50Hz,50,48 hours, confirm its operation after left in the standard condition for 1 hour. REF No AMPLUS W04159-ADAPTOR Page 8

9 16. MODEL LIST MODEL No. RATED OUTPUT VDC 0-800mA VDC 0-800mA VDC 0-800mA VDC 0-670mA VDC 0-570mA VDC 0-500mA VDC 0-440mA VDC 0-400mA VDC 0-360mA VDC 0-330mA REF No AMPLUS W04159-ADAPTOR Page 9