2547 FRONT END LOADER

Transcription

1 2547 FRONT END LOADER Published 10/11 PARTS MANUAL SECTION 1-37 MATERIAL HANDLING PARTS MANUAL

2 PARTS ORDERING GUIDE The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this section. 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required. 2. The Purchase Order must include the name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered. 3. The Purchase Order must clearly list the quantity of each part, the complete and correct part number (be sure to include all periods), and the basic name of the part. 4. The Manufacturer reserves the right to substitute parts where applicable. 5. Some parts are unlisted items which are special production items not normally stocked and are subject to special handling. Request a quotation for such parts before sending a Purchase Order. 6. The Manufacturer reserves the right to change prices without prior notice. For maximum safety and to guarantee optimum product reliability, always use genuine BUSH HOG Parts. The use of inferior replacement parts may causepremature or catastrophic failure which could result in serious injury or death.direct any questions regarding parts to: BUSH HOG 2501 Griffin Ave. Selma, AL Contact Us Alamo Group Inc.

3

4 LIMITED WARRANTY Bush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an authorized Bush Hog dealer, that the equipment be free from defects in material and workmanship for a period of one (1) year for non-commercial, state and municipalities use and ninety (90) days for commercial use from date of retail sale. The obligation of Bush Hog to the purchaser under this warranty is limited to the repair or replacement of defective parts. Replacement or repair parts installed in the equipment covered by this limited warranty are warranted for ninety (90) days from the date of purchase of such part or to the expiration of the applicable new equipment warranty period, whichever occurs later. Warranted parts shall be provided at no cost to the user at an authorized Bush Hog dealer during regular working hours. Bush Hog reserves the right to inspect any equipment or parts which are claimed to have been defective in material or workmanship. DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGES Bush Hog s obligation under this limited warranty, to the extent allowed by law, is in lieu of all warranties, implied or expressed, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE and any liability for incidental and consequential damages with respect to the sale or use of the items warranted. Such incidental and consequential damages shall include but not be limited to: transportation charges other than normal freight charges; cost of installation other than cost approved by Bush Hog; duty; taxes; charges for normal service or adjustment; loss of crops or any other loss of income; rental of substitute equipment, expenses due to loss, damage, detention or delay in the delivery of equipment or parts resulting from acts beyond the control of Bush Hog. THIS LIMITED WARRANTY SHALL NOT APPLY: 1. To vendor items which carry their own warranties, such as engines, tires, and tubes. 2. If the unit has been subjected to misapplication, abuse, misuse, negligence, fire or other accident. 3. If parts not made or supplied by Bush Hog have been used in connection with the unit, if, in the sole judgement of Bush Hog such use affects its performance, stability or reliability. 4. If the unit has been altered or repaired outside of an authorized Bush Hog dealership in a manner which, in the sole judgement of Bush Hog, affects its performance, stability or reliability. 5. To normal maintenance service and normal replacement items such as gearbox lubricant, hydraulic fluid, worn blades, or to normal deterioration of such things as belts and exterior finish due to use or exposure. 6. To expendable or wear items such as teeth, chains, sprockets, belts, springs and any other items that in the company s sole judgement is a wear item. NO EMPLOYEE OR REPRESENTATIVE OF BUSH HOG IS AUTHORIZED TO CHANGE THIS LIMITED WARRANTY IN ANY WAY OR GRANT ANY OTHER WARRANTY UNLESS SUCH CHANGE IS MADE IN WRITING AND SIGNED BY BUSH HOG S SERVICE MANAGER, 2501 GRIFFIN AVE., SELMA, ALABAMA Record the model number, serial number and date purchased. This information will be helpful to your dealer if parts or service are required. MODEL NUMBER SERIAL NUMBER DATE OF RETAIL SALE MAKE CERTAIN THE WARRANTY HAS BEEN FILED WITH BUSH HOG SELMA, ALABAMA

5 TABLE OF CONTENT 2547 FRONT END LOADER ITEM FRAMES Mainframe & Subframe A-1 MOUNTING KITS Kit John Deere 5200, 5300 & WD & FWA ROPS B-1 Kit New Holland 2810, 2910, 3910 FWA, WD ROPS, 3230, 3430, 3930, 4630, 4830 and WD and FWA ROPS or Cab B-2 Kit New Holland 3230, 3430, 3930 & WD and ROPS, 4000, 4100, 4600 & WD All Purpose ROPS B-3 Kit Kubota M4030, M4030F, M4030SU, M5030, M5030F, M5030SU, M6030, M6030F, M6030SU 2WD & M4030DT, M5030DT, M5030SUMDT & M6030DT FWA ROPS B-4 Kit Kubota M730 SUDT FWA & M7030SU 2WD B-5 Kit Case IH 595, 695 & 8952WD ROPS B-6 Kit Massey Ferguson 360 2WD & FWA, 360 Utility 2WD & 362 2WD or FWA ROPS B-7 Kit John Deere 2350, 2550, 2355, 2555, 2750, WD & FWA ROPS or Cab B-8 Kit Massey Ferguson 375 2WD & FWA ROPS & 383 2WD with or without Cab B-9 Kit Kubota M4700 & M4500 FWA ROPS B-10 Kit Kubota M6800 & FWA ROPS or Cab B-11 Kit Case IH C50 & C60 2WD & FWA ROPS B-14 Kit Kubota M4800, M4900 & M5700 2WD & FWA ROPS or Cab M4800SU 2WD ROPS & M4800SUD FWA ROPS B-12,1-37B-13 Kit John Deere 5410, 5420, 5425, 5510, 5520, 2WD & FWA ROPS or Cab B-15 Kit New Holland TL70 & TL80 2WD & FWA ROPS or Cab B-16 Kit New Holland 4835, 5635, 6635, 7635, TL90 & TL100 2WD & FWA ROPS or Cab B-17 Kit New Holland TN55, TN55D, TN60A, TN60DA, TN65, TN65D, TN70, TN70A, TN70D, TN70DA, TN75, TN75A, TN75D & TN75DA 2WD & FWA ROPS or Cab B-18 Kit John Deere 5210, 5220, 5225, 5310, 5320,& WD, FWA, ROPS or Cab B-19 Kit New Holland TT55 2WD & FWA w/rops b-20 Kit New Holland TT75 2WD & FWA w/rops b-21 Kit Case IH JX1080U, JX1090U & JX1100U 2WD & FWA ROPS & Cab New Holland TL80A, TL90A & TL100A 2WD & FWA ROPS or Cab B-22 Kit New Holland TT60A, TT75A 2WD & FWA w/rops b-23 ATTACHMENTS Material Bucket - Pin On C-1 Bale Spear (Pin On) C-2 Pallet Fork (Pin On) C-3 Implement Boom (Pin On) C-4 Rollback Protector (Pin On) C-5 Material Bucket - Quick Attach C-6 Bale Spear - Single Probe C-7 Pallet Fork Assembly C-8 SSL Quick Attach Device C-9 Bale Spear - Dual Probe C & 72 Brush Grapple Assembly & C-11 Wear Edges C-12 Tooth Bar & for 72 & 84 Bucket C-13 PAGE (Continued)

6 TABLE OF CONTENT, CONT D 2547 FRONT END LOADER ITEM ATTACHMENTS (Cont d) Weight Bracket C-14 No Tools Quick Attach C-15 Hydraulic Self Leveling Kit C-16 Self Leveling Valve C-17 Electronic Third Function Kit C-18, 1-37C-19 3rd Function Hose Kit C-20 Selector Valve - Electronic Third Function Kit C-21 HYDRAULICS Hydraulic System D-1 Valve Assembly ( Prince LVR Parallel) D-2, 1-37D-3 Valve Assembly ( Prince LVS Series) D-4, 1-37D-5 Valve Assembly ( Dukes DV-27 Control Valve) D-6, 1-37D-7 Valve Assembly ( Prince RD-5200 Control Valve) D-8 Lift & Bucket Cylinder D-9 Hydraulic Cylinder - Brush Grapple D-10 Hose Kit ( Rear Remote Outlets with Male Quick Couplers) E-1 Hose Kit ( Rear Remote Outlets without Male Quick Couplers) E-2 Hose Kit Massey Ferguson 360, 360 Utility, 362, 375, E-3 Hose Kit Case IH JX1080U, JX1090U & JX1100U New Holland 4835, 5635, 6635, 7635,TL70, TL80, TL90, TL100, TL80A, TL90A & TL100A E-4 Hose Kit Case IH JX1080U, JX1090U & JX1100U New Holland 4835, 5635, 6635, 7635,TL70, TL80, TL90, TL100, TL80A, TL90A & TL100A E-5 Hose Kit New Holland TN55, TN55D, TN60A, TN60DA, TN65, TN65D, TN70, TN70A, TN70D, TN70DA, TN75, TN75A, TN75D & TN75DA E-6 Hose Kit New Holland TN55, TN55D, TN60A, TN60DA, TN65, TN65D, TN70, TN70A, TN70D, TN70DA, TN75, TN75A, TN75D & TN75DA E-7 Hose Kit John Deere 5210, 5220, 5225, 5310, 5320, 5325, 5410, 5420, 5425, 5510, 5520 & E-8 Hose Kit John Deere 5210, 5220, 5225, 5310, 5320, 5325, 5410, 5420, 5425, 5510, 5520 & E-9 Hose Kit New Holland TN55, TN55D, TN60A, TN60DA, TN65, TN65D, TN70, TN70A, TN70D, TN70DA, TN75, TN75A, TN75D & TN75DA E-10, 1-37E-11 Valve Kit John Deere 5200, 5300 & F-2, 1-37F-3 Valve Kit Case IH 595, 695 & 895 FWA F-1 Valve Kit Massey Ferguson 360 & F-4, 1-37F-5 Valve Kit John Deere 2350, 2355, 2550 & F-6, 1-37F-7 Valve Kit New Holland 4000, 4100, 4600, 2810, 2910, 3910, 4610, 3230, 3430, 3930, 4630, 4830 & 5030 ROPS F-8, 1-37F-9, 1-37F-10, 1-37F-11 Valve Kit Massey Ferguson 375 & F-12, 1-37F-13 Valve Kit Case IH C50 & C60 ROPS F-14, 1-37F-15 Valve Kit New Holland TT55 & TT F-16, 1-37F-17 Valve Kit New Holland TN55, TN60A, TN65, TN70, TN70A, TN75 & TN75DA ROPS F-18, 1-37F-19 Valve Kit Kubota M4030, M4030F, M4030SU, M5030, M5030F, M5030SU, M6030, M6030F, M6030SU & M7030 SUDT F-20, 1-37F-21 Valve Kit Kubota M4700 & M F-22, 1-37F-23 PAGE (Continued)

7 TABLE OF CONTENT, CONT D 2547 FRONT END LOADER ITEM HYDRAULICS (Cont d) Valve Kit Kubota M4800SU, M4800SUD, M4800, M4900, M5700 & M6800 ROPS F-24, 1-37F-25 Valve Kit Case IH JX1080U, JX1090U & JX1100U ROPS or Cab New Holland TL80A, TL90A & TL100A ROPS or Cab F-26, 1-37F-27 Valve Kit ( Universal - ROPS Cab Open Center w/power Beyond Sleeve F-28, 1-37F-29 Valve Kit John Deere 5210, 5310, 5410, 5510, 5220, 5320, 5420, 5520, 5225, 5325, 5425, 2WD or FWA, ROPS F-30, 1-37F-31 Valve Kit New Holland TT60A & TT75A F-32, 1-37F-33 Spool Mono-Block Valve Assembly F-34 Spring Center Float Detent & Regen Assembly F-35 Spring Center Assembly F-36 Joystick Assembly F-37 Joystick and Cable Harness F-38, 1-37F-39 GRILL GUARD Grill Guard Kit New Holland 00, 10 & 30 Series G-1 Grill Guard Kit New Holland 35 Series G-2 Grill Guard Kit Kubota M G-3 Grill Guard Kit Kubota M4800SU, M4700, M4900, M5400 & M G-4 Grill Guard Kit Case IH C50, CX50, C60 & CX G-5 Grill Guard Kit New Holland TL70, TL80, TL90 & TL G-6 Grill Guard Kit New Holland TT55 & TT G-7 Grill Guard Kit Case IH JX1080U, JX1090U & JX1100U New Holland TL80A, TL90A & TL100A G-8 Grill Guard Kit New Holland TT60A, TT75A G-9 DECALS Decal - Placement H-1 Decal - Pictorials H-2 PAGE

8 NOTES:

9 MAINFRAME & SUBFRAME Frame, Lift Boom With Decals Cylinder, Bucket (Code JL) Cylinder, Lift (Code JK) Frame, Side Left With Decals Frame, Side Right With Decals Pin, 1-1/4" x 7-1/4" Pin, 1-1/4" x 6-7/8" Pin, 1-1/4" x 6-1/4" Pin, 1-1/4" x 5-7/8" Pin, 1-1/4" x 5-1/2" Bolt, Shoulder Pin, Cotter, 1/8" x 1" Rod, Bucket Level Indicator Tube, Guide Hinge Bolt, Assembly Flatwasher, 3/4" Bolt, Carriage 3/4"-10 x Fitting, Grease, 1/4"-28 Straight Capscrew, 3/8"-16 x 2-3/4" Hex Nut, 3/8" Capscrew, 3/8"-16 x 2-3/4" Locknut, 3/4" Nut, Elastic, 3/ Fitting, Grease, 1/4"-28, Flatwasher, 3/8" A-1

10

11 MOUNTING KIT John Deere 5200, 5300 & WD & FWA ROPS Bracket, Front Mounting Crossplate Bracket, Midmounting, Right Bracket, Midmounting, Left (Not Shown) Capscrew, Metric, 16mm-2.0mm x 40mm Flatwasher, 5/8 SAE Yoke Assembly Capscrew, 3/4-10 x Locknut, 3/ Capscrew, Metric, 20mm-2.50mm x 40mm Lockwasher, 5/ Capscrew, 3/4-10 x 2-1/ Capscrew, 3/4-10 x 1-3/ Capscrew, 5/8-11 x 1-1/ Lockwasher, 3/ Decal, Warning "No Tow" Lockwasher, 20mm B-1

12 MOUNTING KIT New Holland - see Price Sheet for Models Bracket,Front Mounting Crossplate Bracket, Midmounting, Right Bracket, Midmounting, Left (Not Shown) Pedestal, Mid Mounting Pedestal, Mid Mounting Yoke Assembly Bracket, Hose Restraint Capscrew, 3/4 x 10 x 2-1/ Capscrew, 3/4-10 x Capscrew, 3/4-10 x 1-1/ Screw, Self Tapping, 1/4 x Capscrew, 5/16 x 3/ Bracket, Muffler Mounting Extension Lockwasher, 3/ Flatwasher, 3/ Locknut, 3/ Locknut, 5/ Decal, "Warning, Do Not Use For Towing" Stop, Axle, Right (FWA Only) Stop, Axle, Left (FWA Only) Spacer, Flat Bracket, Light Remounting Foot, Yoke, Adjustable Capscrew, 1/2-13 x 1-1/ Locknut, 1/ B-2

13 MOUNTING KIT New Holland - see Price Sheet for Models NO. NO. DESCRIPTION QTY Bracket, Front Mounting Crosstie, Assembly Bracket, Midmount, Right Bracket, Midmount, Left Flat, Crosstie Clamp Spacer, Flat, 1-1/2 x 1-1/2 x 4-1/ Yoke Assembly Bracket, Hose Restraint Screw,Cap,3/4-10 x 2-1/ Capscrew, 3/4-10 x Screw,Cap,3/4-10 x Capscrew, 3/4-10 x 3-1/ Capscrew, 5/16 x 3/ Bracket, Muffler Mounting Extension Lockwasher, 3/ Flatwasher, 3/ Locknut, 3/ Locknut, 5/ Decal, "Warning, Do Not Use For Towing" Spacer, Flat, 1/2 x 1-1/2 x 4-1/ Spacer, Plate Capscrew, 3/4-10 x Capscrew, 3/4-10 x Foot, Adjustable, Yoke Capscrew, 1/2-13 x 1-1/ Locknut, 1/ B-3

14 MOUNTING KIT Kubota - see Price Sheet for Models Bracket, Front Mounting Crossplate Bracket, Midmounting, Right Bracket, Midmounting, Left Yoke Assembly Bar, Reinforcing Bracket, Rear Channel Capscrew, 5/8-11 x 1-3/ Capscrew, 16mm-1.50 x 120mm (Not Used On M4030SU) Capscrew, 16mm-150 x 40mm Flatwasher, 5/ Lockwasher, 5/ Locknut, 3/ Locknut, 5/ Capscrew, 3/4-10 x 2-1/ Capscrew, 3/4-10 x Decal, "Warning, Do Not Use For Towing" Capscrew, 16mm-1.50mm x 45mm (Used On M4030SU Only) Support Plate B-4

15 MOUNTING KIT Kubota - M7030 SUDT FWA & M7030SU 2WD Bracket, Front Mounting Crossplate Bracket, Midmounting, Right Bracket, Midmounting, Left Yoke Assembly Capscrew, 16mm-1.50mm x 45mm Bracket, Rear Channel Capscrew, 5/8-11 x 1-3/ Capscrew, 16mm-1.50 x 100mm Capscrew, 16mm-1.50 x 40mm Flatwasher, 5/ Lockwasher, 5/ Locknut, 3/ Locknut, 5/ Capscrew, 3/4-10 x 2-1/ Capscrew, 3/4-10 x Decal, "Warning, Do Not Use For Towing" Step Assembly Capscrew, 1/2-13 x 1-1/ Locknut, 1/ B-5

16 MOUNTING KIT Case IH - 595, 695 & 895 2WD ROPS Bracket, Front Mounting Extension, Yoke, Assembly Bracket, Midmounting, Right Bracket, Midmounting, Left Yoke Assembly Lockwasher, 3/ Locknut, 3/ Capscrew, 3/4-10 x 1-1/ Capscrew, 3/4-10 x 2-1/ Capscrew, 3/4-10 x Decal, "Warning, Do Not Use For Towing" Capscrew, 1/2-13 x 1-1/ Locknut, 1/ Flatwasher, 3/ Cotter, Hairpin Pin, Clevis, 1/2 x 1-5/ B-6

17 MOUNTING KIT Massey Ferguson WD & FWA, 360 Utility 2WD, & 362 2WD or FWA ROPS Bracket, Front Mounting Bracket, Midmounting Plate, Cover Yoke Assembly Capscrew, 5/8-11 x Capscrew, 5/8-11 x 1-1/ Capscrew, 5/8-11 x 2-1/ Lockwasher, 5/ Locknut, 3/ Capscrew, 3/4-10 x 2-1/ Decal, "Warning, Do Not Use For Towing" B-7

18 MOUNTING KIT John Deere , 2550, 2355, 2555, 2750, WD & FWA ROPS or Cab Bracket, Front Mounting Crossplate Bracket, Midmounting, Right Bracket, Midmounting, Left Yoke Assembly Locknut, 3/ Capscrew, 3/4-10 x 2-1/ Decal, "Warning, Do Not Use For Towing" Angle, Step Spacer, Plate Spacer, Tube, 5/8 x 3/ Capscrew, 5/8-11 x 1-3/ Locknut, 5/ Capscrew, 3/4-10 x Lockwasher, 3/ Capscrew, 1/2-13 x 1-1/ Locknut, 1/ Lockwasher, 5/ Capscrew, 5/8-11 x 3-3/ B-8

19 MOUNTING KIT Massey Ferguson WD & FWA ROPS & 383 2WD with or without Cab Bracket, Front Mounting Bracket, Right, Midmounting Bracket, Left, Mid Mounting (Not Shown) Cross Tie Assembly Plate, Cover Yoke Assembly Capscrew, 5/8-11 x Capscrew, 5/8-11 x Lockwasher, 5/ Locknut, 3/ Capscrew, 5/8-11 x 1-1/ Capscrew, 3/4-10 x 2-1/ Decal, "Warning, Do Not Use For Towing" Locknut, 5/ Capscrew, 5/8-11 x 2-3/ Flatwasher, 5/ Capscrew, 3/4-10 x 1-1/ Flatwasher, 3/ Lockwasher, 3/ Plate, Spacer (Tractors With Cab Oniy) Tube, Spacer, 5/8 (Tractors Less Cab Only) Tube, Spacer, 1-3/4 (Tractors Less Cab Only) B-9

20 MOUNTING KIT Kubota - M4700 & M5400 FWA ROPS Bracket, Front Mounting Crossplate Bracket, Midmounting, Right Bracket, Midmounting, Left Yoke Assembly Capscrew, 5/8-11 x Capscrew, 16mm-1.50 x 100mm Capscrew, 16mm-1.50 x 45mm Lockwasher, 5/ Locknut, 3/ Locknut, 5/ Capscrew, 3/4-10 x 2-1/ Decal, "Warning, Do Not Use For Towing B-10

21 MOUNTING KIT Kubota - M6800 & FWA ROPS or Cab Bracket, Front Mounting Crossmember, Front Bracket, Midmounting, Right Bracket, Midmounling, Left Yoke Assembly, With Decals Crossmember, Rear Capscrew, 16mm-1.50 x 100mm Spacer Plate Lockwasher, 5/ Locknut, 3/ Locknut, 5/ Capscrew, 3/4-10 x 2-1/ Decal, "Warning, Do Not Use For Towing" Capscrew, 16mm-1.50 x 35mm Capscrew, 16mm-1.50 x 75mm Capscrew, 5/8-11 x 1-3/ Capscrew, 14mm-1.50 x 90mm Lockwasher, 9/ Flatwasher, 5/ Capscrew, 1/4-20 x 3/ Lockwasher, 1/ Nut, 1/ Mounting Plate Spacer Tube B-11

22 MOUNTING KIT Kubota - M4800, M4900 & M5700 2WD & FWA ROPS or Cab M4800SU 2WD ROPS & M4800SUD FWA ROPS 1-37B-12

23 MOUNTING KIT Kubota - M4800, M4900 & M5700 2WD & FWA ROPS or Cab M4800SU 2WD ROPS & M4800SUD FWA ROPS Bracket, Front Mounting Crossmember, Front Bracket, Mid Mounting, Right Bracket, Mid Mounting, Left Bracket, Yoke, With Decals (Includes Item 13.) Crossmember, Rear Capscrew, 16mm-1.50 x 100mm Spacer, Plate (Rops Only) Lockwasher, 5/8" Locknut, 3/ Locknut, 5/8-11 (Use Only Qty. 8 For Tractors Equipped With Cab.) Capscrew, 3/4-10 x 2-1/2" Decal, Warning, Do Not Use For Towing (Included With Item 5.) Capscrew, 16mm-1.50 x 35mm Capscrew, 16mm-1.50 x 75mm Capscrew, 5/8-11 x 1-3/4" Capscrew, 18mm-1.50 x 50mm Lockwasher, 18mm Flatwasher, 5/8" (Rops Only) Capscrew, 1/4-20 x 3/4" Lockwasher, 1/4" Locknut, 1/ Mounting Plate Capscrew, 16mm-1.50 x 40mm (Rops Only) Plow, Bolt, 5/8-11 x 2-3/4" (Rops Only) Spacer, Tube B-13

24 MOUNTING KIT Case IH - C50 & C60 2WD & FWA ROPS Bracket, Mounting, Front (Includes Item 15) Bracket, Mounting, Mid, Left Bracket, Mounting, Mid, Right Bracket, Yoke, With Decal Oscillation Stop, Left Oscillation Stop, Right Spacer, Plate, 3/8 x 5 x 9" Spacer, Plate, 3/8 x 2-1/4 x 5" Spacer, Plate, 1/4 x 1-1/2 x 4-1/4" Capscrew, 3/4-10 x 2-1/2", Grade Capscrew, 20mm-2.5 x 60mm, Class Capscrew, 20mm-2.5 x 50mm, Class Lockwasher, 20mm Locknut, 3/4-10, Type-N Decal, Warning: Do Not Tow B-14

25 MOUNTING KIT John Deere , 5420, 5425, 5510, 5520, 2WD & FWA ROPS or Cab Front Mount Bracket Mid Mount Assembly, Left Mid Mount Assembly, Right Yoke Assembly, With Decals Oscillation Stop Assembly, Left Oscillation Stop Assembly, Right Spacer Capscrew, 3/4-10 x 2-1/ Capscrew, 3/4-10 x 2-1/4, Gr Capscrew, 5/8-11 x 1-1/ Capscrew, 20mm-2.5 x 50mm Capscrew, 16mm-2.0 x 65mm Capscrew, 16mm-2.0 x 45mm Locknut, 3/ Lockwasher, 5/ Lockwasher, 3/ Lockwasher, 20mm Flatwasher, 5/ Decal, Warning B-15

26 MOUNTING KIT New Holland - TL70 & TL80 2WD & FWA ROPS or Cab Bracket, Front Mounting Bracket, Midmounting, Left Bracket, Midmounting, Right Yoke Assembly Decal, "Warning, Do Not Use For Towing" Tie Strap, Adjustable, 3/16 x Capscrew, mm x 60mm Lockwasher, 7/ Flatwasher, 7/ Capscrew, mm x 120mm Capscrew, mm x 90mm Locknut, 3/ Capscrew, 3/4-10 x 2-1/ Lockwasher, 5/ Oscillation Stop, Left Oscillation Stop, Right Capscrew, mm x 40mm B-16

27 MOUNTING KIT New Holland - see Price Sheet for Models Bracket, Front Mounting Bracket, Midmounting, Left Bracket, Midmounting, Right Yoke Assembly Decal, Warning, Do Not Use For Towing Capscrew, 20mm-2.5 x 40mm Capscrew, mm x 60mm Lockwasher, 7/ Flatwasher, 7/ Capscrew, mm x 120mm Capscrew, mm x 90mm Locknut, 3/ Capscrew, 3/4-10 x 2-1/ Lockwasher, 5/ Oscillation Stop, Left (Not Shown) Oscillation Stop, Right Flatwasher, 5/ Capscrew, mm x 100mm B-17

28 MOUNTING KIT New Holland - see Price Sheet for Models Front Mount Bracket Mid Mount Assembly, Left Mid Mount Assembly, Right Yoke Assembly Lockwasher, 20mm Flatwasher, 7/ Capscrew, 20mm-2.5 x 40mm Capscrew, 3/4-10 x 2-1/ Locknut, 3/ Capscrew, 3/8-16 x Capscrew, 20mm-2.5 x 45mm Capscrew, 20mm-2.5 x 50mm Locknut, 3/ Oscillation Stop Assembly, Left Oscillation Stop Assembly, Right Decal, Warning Trim, Black, Plastic, 6" Spacer Block Capscrew, 20mm-2.5 x 75mm B-18

29 MOUNTING KIT John Deere , 5220, 5225, 5310, 5320 & WD, FWA, ROPS or Cab Front Mount Bracket Mid Mount Assembly, Left Mid Mount Assembly, Right Yoke Assembly, With Decals Oscillation Stop Assembly, Left Oscillation Stop Assembly, Right Spacer Capscrew, 3/4-10 x 2-1/ Capscrew, 3/4-10 x 2-1/4, Gr Capscrew, 5/8-11 x 1-1/ Capscrew, 20mm-2.5 x 50mm Capscrew, 16mm-2.0 x 65mm Capscrew, 16mm-2.0 x 45mm Locknut, 3/ Lockwasher, 5/ Lockwasher, 3/ Lockwasher, 20mm Flatwasher, 5/ Decal, Warning B-19

30 MOUNTING KIT New Holland - TT55 2WD & FWA w/rops Bracket, Mid Mounting, Left Bracket, Mid Mounting, Right Bracket, Front Mounting Yoke, Loader Front, With Decals Capscrew, 16mm-1.5 x 40mm, Class Capscrew, 16mm-1.5 x 60mm, Class Flatwasher, 5/8" Lockwasher, 5/8" Capscrew, 3/4-10 x 1-3/4", Grade Lockwasher, 3/4" Capscrew, 3/4-10 x 2-1/2", Grade Locknut, 3/4-10, Type N, Grade Decal, Warning, Do Not Tow B-20

31 MOUNTING KIT New Holland - TT75 2WD & FWA w/rops Bracket, Mid Mounting, Left Bracket, Mid Mounting, Right Bracket, Front Mounting Yoke, Loader Front, With Decals Capscrew, 16mm-1.5 x 40mm, Class Capscrew, 16mm-1.5 x 60mm, Class Flatwasher, 5/8" Lockwasher, 5/8" Capscrew, 3/4-10 x 1-3/4", Grade Lockwasher, 3/4" Capscrew, 3/4-10 x 2-1/2", Grade Locknut, 3/4-10, Type N, Grade Decal, Warning, Do Not Tow B-21

32 MOUNTING KIT Case IH - see Price Sheet for Models New Holland - see Price Sheet for Models Bracket, Mid Mounting, Left Bracket, Mid Mounting, Right Bracket, Front Mounting Yoke Assembly Decal, Warning, "Do Not Use For Towing" Spacer, Rear Spacer, Front Capscrew, 16mm-1.50mm x 65mm Capscrew, 20mm-2.50mm x 80mm Capscrew, 20mm-2.50mm x 65mm Capscrew, 16mm-1.50mm x 90mm Capscrew, 20mm-2.50mm x 50mm Capscrew, 20mm-2.50mm x 70mm Lockwasher, 20mm Lockwasher, 5/ Capscrew, 3/4-10 x 2-1/ Locknut, 3/ B-22

33 MOUNTING KIT New Holland - TT60A, TT75A 2WD & FWA w/rops Wdmt, Left Mid-Mount Wdmt, Right Mid-Mount Wdmt, Front Clevis Mount Wdmt, Yoke Extension, Foot Capscrew, 16mm-1.5 x 45 Mm Class 8.8 YDP Capscrew, 16mm-1.5 x 50 Mm Class 8.8 YDP Capscrew, 16mm-1.5 x 70 Mm Class 8.8 YDP Flatwasher, 5/8 2 NO. NO. DESCRITION QTY Lockwasher, 5/ Capscrew, 3/4-10 x 2-1/2 Gr Locknut, 3/4-10 Gr Capscrew, 1/2-13 x 1-1/4 Gr Locknut, 1/2-13 Gr Decal, Warning, Do Not Tow Mount, Tool Box Flatwasher, 1/ Spacer, 1/ B-23

34

35 MATERIAL BUCKET - PIN ON 1 * Bucket, 72 Standard (Includes Cutting Edges) 1 * Bucket, 72" Heavy Duty (Includes Cutting Edges) 1 * Bucket, 84" Heavy Duty (Includes Cutting Edges) Cutting Edge, Left Side (72 Std.) Cutting Edge, Left Side (72 H.D. & 84 H.D.) Cutting Edge, Bottom (72" Std.) Cutting Edge, Bottom (72 H.D.) Cutting Edge, Bottom (84 H.D.) Cutting Edge, Right Side (72 Std.) Cutting Edge, Right Side (72 H.D. & 84 H.D.) 1 *Not sold as repair part. Order from Whole Goods 1-37C-1

36 BALE SPEAR (PIN ON) 1 * Bracket, Round Bale Spear Spike, Round Bale Spear Capscrew, 1/2-13 x 3-1/ Locknut, 1/ * Bracket Assembly Not Sold As Repair Part 1-37C-2

37 PALLET FORK (PIN ON) Frame, Pallet Fork Capscrew, 5/16-18 x Locknut, 5/ Tine, Pallet Fork Shaft, Tine Decal, Warning: Pinch Area Decal, Pallet Fork Rating Flatwasher, 1-3/ C-3

38 IMPLEMENT BOOM (PIN ON) Boom Assembly, Main Boom Assembly, Inner Shaft, Boom Mounting Hook, Grab Hair Pin, Clip Pin, Latch Hanger, Boom Clevis Pin Hair Pin, Clip Decal, Warning, Do Not Use Decal, Boom Rating C-4

39 ROLLBACK PROTECTOR (PIN ON) Rollback Protector Capscrew, 5/8-11 x Locknut, 5/ Capscrew, 5/8-11 x 1-1/ C-5

40 MATERIAL BUCKET - QUICK ATTACH 1 * Bucket, 72 Standard Quick Attach (Includes Cutting Edge) 1 * Bucket, 72 Heavy Duty Quick Attach (Includes Cutting Edge) 1 * Bucket, 84 Heavy Duty Quick Attach (Includes Cutting Edge) 1 * Bucket, 84 Snow & Light H.V. Mat l Quick Attach (Includes Cutting Edge) Cutting Edge, Left Side (72 Std.) Cutting Edge, Left Side (72 H.D., 84 H.D. & 84 Snow & Light H.V. Mat l) Cutting Edge, Bottom (72 Std., No Holes) Cutting Edge, Bottom (72 H.D., w/holes) Cutting Edge, Bottom (84 H.D., w/holes) Cutting Edge, Bottom (84 Snow & Light H.V. Material, No Holes) Cutting Edge, Right Side (72 Std.) Cutting Edge, Right Side (72 H.D., 84 H.D. & 84 Snow & Light H.V. Mat l) 1 *Not sold as repair part. Order from Whole Goods 1-37C-6

41 BALE SPEAR-SINGLE PROBE * Bracket, Round Bale Spear Spike, Round Bale Spear Capscrew, 1/2-13 x 3-1/ Locknut, 1/ Step, Anti Slip 2 * Not sold as repair part 1-37C-7

42 PALLET FORK ASSEMBLY Frame, Pallet Fork Tine Assembly, Pallet Fork Decal, Pallet Fork Rating C-8

43 SSL QUICK ATTACH DEVICE Frame Assembly Handle Fitting, Grease, 1/ G Spring Pin, 1/4 x 1-1/ Jam Nut, 1/ Disc Spring Pivot Assembly Pivot Pin Cotter Pin 5/32 x Spade Bolt Assembly Spring Pin, Clevis Pin, Latch Spring Guide Assembly Spacer Sheet, Decal (Includes Two Decals) C-9

44 BALE SPEAR-DUAL PROBE Wdmt, Bale Spear Frame, Dual, SS QA Spear, Bale, Super Penetrator Locknut, M28 x C-10

45 60 & 72 BRUSH GRAPPLE ASSEMBLY & Wdmt, Brush Grapple Arm A Hydraulic Cylinder Pin, Hyd. Cylinder Flatwasher, 1, N-SAE, YDP Cotter Pin, 3/16 x Clevis Pin 1 x 2, TCP Tube Adapter, Elbow, Short Fitting,Tee, Bulkhead W/Lknut Nut/ Lock Bulkhead 3/4-16 (Included In Item 8) Hose #8-8FJX90 Short-8MB-33 Lg Nylon Sleeve 2.06 x Hose #6-8FJX -8FJX -35 Lg Hose #6-8FJX -8FJX -44 Lg Decal,Warning 2 17 D516 Decal,Danger-Crush Hazard C-11

46 WEAR EDGES 1 * " Bolt On Reversible Blade 1 * " Bolt On Reversible Blade Plow Bolt, 3/4 x 2-1/ Hex Nut, 3/ Lockwasher, 3/4 - *Order From Wholegoods 1-37C-12

47 TOOTH BAR & for 72 & 84 Bucket 1 * Tooth Bar, Assembly, 72 Bucket 1 * Tooth Bar, Assembly, 84 Bucket Carriage Bolt, 5/8-11 x 1-1/ Lockwasher, 5/ Hex Nut, 5/ Pin, Retaining 7/ Tooth 7/ Shank, Tooth (Replacement) 7/8 *Order from Wholegoods 1-37C-13

48 WEIGHT BRACKET for New Holland 00, 10 & 30 Series Tractors Bracket, Weight Adapter Capscrew, 3/4-10 x 1-1/ Locknut, 3/ C-14

49 NO TOOLS QUICK ATTACH Rod, Tension Linkage Assembly Pin, Clevis 2 4 G Pin, Cotter Handle, No-Tools Pin, Spring Tee-Bolt, Weldment Grip, Handle Decal Right Decal, Left C-15

50 HYDRAULIC SELF LEVELING KIT Valve, Self Leveling Carriage Bolt, 5/16-18 x 2-1/ Hex Nut, 5/ Lockwasher, 5/ Fitting, 3/4-3/4 Tee Fitting, 3/4-3/4 x Fitting, 7/8-3/4 x Hose, 3/8 x 40" Hose, 3/8 x 22" Strap, Reusable Tie Fitting, 7/8-3/4 Male C-16

51 SELF LEVELING VALVE Plug Kit, Unloading Spool Spring, Unloading Spool Plug Kit, Flow Divider Spool Plunger, Load Check Spring, Load Check Plug Kit Load Check Plunger, Load Check Spring, Load Check Plug Kit, Load Check Pin, Adjustment Cap, Adjustment Setscrew, 1/4-28 x Jam Nut, 1/ Cover, Adjustment Repair Kit, Seal C-17

52 ELECTRONIC THIRD FUNCTION KIT C-18

53 ELECTRONIC THIRD FUNCTION KIT Valve, Double Selector Bracket, Mounting Cover, Valve, Assembly Capscrew, 1/4-20 x Hex Nut, 1/ Fitting, Elbow, 3/4-16 x 3/ , (Extra Long) Fitting, Elbow, 3/4-16 x 3/ Fitting, Adapter, 3/4-16 O-Ring x 3/8 NPT Fitting, Coupler, Female Wiring Harness, 300" Connector, Wire, 14 Ga Hose, 1/2 x 72" Screw, Hex Head Self Tapping, 1" Tee, Swivel Nut Run Cap, End, 3/4-16 JIC Strap, Plastic Adjustable, 1/2" Angle Bracket Bracket, Switch Plate, Clamp Machine Screw, #4-40 x 3/ Switch, Push Button Setscrew, 1/4-28 x 3/8 Square Head Hose, 1/2 x 28" Holder, Fuse Fuse, 10 Amp Wiring Harness Strap, Adjustable, Plastic, 3/16" Clamp, Tube, 1/ Band, Plastic, Spiral, Blue Band, Plastic, Spiral, Red Plug, Dust Connector, 2 Pole Terminal, 3/8 x 14 Ga Machine Screw, #4-40 x 5/ Connector Tab Plastice Cover Flatwasher, 1/4 SAE YDP Spacer, Plate Nylon Sleeve, 1.75 x 72" C-19

54 3rd FUNCTION HOSE KIT Bracket, Quick Coupler Screw, Hex Head Self Tapping, 1/4-14 x 1-1/ Coupler, Quick, Female Band, Spiral, Blue, 5/ Band, Spiral, Red, 5/ Bushing, 3/4 x 1-1/ Spacer, Plastic Tie Strap, 1/2 x Hose, 3/8 x C-20

55 SELECTOR VALVE - ELECTRONIC THIRD FUNCTION KIT 1 * Plug Spring 1 3 * Body 1 4 * Spool O-Ring 1 6 * Tube Binder Coil Binder Retainer C-21

56

57 HYDRAULIC SYSTEM Hose, 3/8" x Hose, 3/8" x Hose, 3/8" x Hose, 3/8" x Oil Line (LCB) Oil Line (LCR) Oil Line (TCR) Oil Line (TCB) Adj, Strap 3/16" x Pad, Oil Line Oil Line Clamp Flange Nut, 3/8" Shield, Oil Line Spacer, Rubber Canister, With Cap & Seal Seal, Manual Canister Capscrew, 1/4-20 x.75" Flatwasher, 1/4" Locknut, 1/4" D-1

58 VALVE ASSEMBLY PRINCE (LVR) 3000 PSI & 2500 PSI RELIEF 1-37D-2

59 VALVE ASSEMBLY PRINCE (LVR) 3000 PSI & 2500 PSI RELIEF Valve Assembly (3000 PSI Relief) Valve Assembly (2500 PSI Relief) Seal Kit Power Beyond Sleeve Relief Valve (3000 PSI) Relief Valve (2500 PSI) Relief Valve (3000 PSI) Float Kit, (Includes 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, And 26) Regen Kit, (Includes Items 12, 13, 14, 15, 16, 17, 19, 20, 21, 24, And 26) Boot, Rubber, Valve Handle Stud, Spool Adapter Plate Rod End Rod End, Assembly Clevis End Cap (HC-V-AA26) stamped on end cap, identifies valve and relief setting End Cap (HC-V-AA23) stamped on end cap, identifies valve and relief setting Capscrew, Socket Head, 1/4-20 x 1/ Plug, Load Check Hex Nut, 5/ Capscrew, Socket Head, 1/4-20 x 7/ Plate Washer, Shim, 5/ Hex Nut, 7/ End, Spool Handle, Valve, Standard Ball, Handle Capscrew, Socket Head, 5/16-24 x 3/ Lockwasher, 7/ D-3

60 VALVE ASSEMBLY PRINCE (LVS) 3000 PSI, 2500 PSI & 2000 PSI RELIEF 1-37D-4

61 VALVE ASSEMBLY PRINCE (LVS) 3000 PSI, 2500 PSI & 2000 PSI RELIEF Valve Assembly (3000 PSI Relief) Valve Assembly (2500 PSI Relief) Valve Assembly (2000 PSI Relief) Seal Kit, Prince LVS Valve Relief Valve (2000 PSI) Relief Valve (2500 PSI) Relief Valve (3000 PSI) Plug, Load Check Float Kit (Includes Items 6, 7, 8, 10, 11, 12, 13, 14, 15, 16, 17, And 18) Regen Kit (Includes Items 6, 7, 9, 10, 11, 12, 13, 14, 15, 16, 17, And 18) End Cap, (HC-V-AA25) stamped on end cap identifies valve and relief setting Handle, Valve, Standard Hex Nut, 7/ Lockwasher, 7/16" Boot, Rubber, Valve Handle Ball, Handle Tie Strap, 3/16" Wide x 13" Long Disk, Adapter, Handle To Linkage Capscrew, Socket Head, 5/16-24 x 3/4" Rod End, Assembly Rod End Stud, Spool Hex Nut, 5/ Clevis, Lock, Housing Capscrew, Socket Head, 1/4-20 x 1-3/4" Capscrew, Socket Head, 1/4-20 x 3/4" Flatwasher, 1/4" Knob, Spool Lock Handle, Spool Lock Blade Lock Ring, Retaining, External Spring 1 40 G Roll Pin D-5

62 VALVE ASSEMBLY DUKES DV-27 CONTROL VALVE 1-37D-6

63 VALVE ASSEMBLY DUKES DV-27 CONTROL VALVE Valve Assembly 1 1 * Valve 1 2 * O-Ring, Spool 4 3 * Washer, Return 2 4 * Spring, Return 1 5 * Spacer, Spring 1 6 * Sleeve 1 7 * Stud, Detent 1 8 * Ring, Retaining 2 9 * Gasket, End Cap 1 10 * Cap, End 1 11 * Screw, Slotted 1 12 * Ball, Steel 2 13 * Spring, Detent 2 14 * Screw, Detent 2 L5 * Spacer, Spring 1 16 * Spring, Return 1 17 * Poppet, Load Check 2 18 * Spring, Load Check 2 19 * O-Ring, Load Check Plug 2 20 * Plug, Load Check 2 21 * O-Ring, Power Beyond 1 22 * Washer, Backup 1 23 * O-Ring, Power Beyond 1 24 * Sleeve, Power Beyond 1 25 * O-Ring, Relief 1 26 * Washer, Backup 1 27 * O-Ring, Relief 1 28 * Washer, Backup 1 29 * Cartridge, Relief Repair Kit, Load Check Repair Kit, Pilot Operated Relief Sleeve Kit, Power Beyond Repair Kit, Spring Centering Repair Kit, Valve Seals (Contains Items 2, 9, 19, 21, 22, 23, 25, 26, 27, & 28) 1 * Parts Are Included In Appropriate Repair Kit 1-37D-7

64 VALVE ASSEMBLY PRINCE RD-5200 CONTROL VALVE Valve Assembly Repair Kit, Seal Repair Kit, Relief Valve Repair Kit, Detent Spring Centering Repair Kit, Spring Centering Handle, Knob Replacement, Handle Knob Hex Nut, 7/ Lockwasher, 7/ Bellows, Molded Adapter, Handle Jam Nut, 3/ Stud, Pivot Pivot, Center Block, Side Slide Capscrew, Hex Soc Hd, 1/4-20 x 3/ Plate, Retainer Plate, Base Jam Nut, 1/ G Pin, Spring, 1/4 x 1-1/ Adapter, Spool Block, Top Slide Lockwasher 1/ Capscrew, 1/4-20 x 1-1/ Backup, Spool Seal Repair Kit, Load Check Plug, Open Center Plug, Closed Center Sleeve,Power Beyond D-8

65 LIFT & BUCKET CYLINDER Rod, Cylinder, (Lift Cylinder) Rod, Cylinder, (Bucket Cylinder) 1 2 * Seal, Wiper 1 3 * Seal, Rod Head, Cylinder (Lift Cylinder) Head, Cylinder (Bucket Cylinder) 1 5 * Ring, Wear 1 6 * Washer, Backup 1 7 * O-Ring 1 8 * Seal, Piston 1 9 * O-Ring Piston (Lift Cylinder) Piston (Bucket Cylinder) 1 11 * Ring, Wear Nut, Lock 1-14 (Lift Cylinder) Nut, Lock 1-14 (Bucket Cylinder) Tube, Cylinder (Lift Cylinder) Tube, Cylinder (Bucket Cylinder) 1 14 * Wire, Retaining Kit, Lift Cylinder Repair, Includes * Items Kit, Bucket Cylinder Repair, Includes * Items D-9

66 HYDRAULIC CYLINDER - BRUSH GRAPPLE 8727A Hydraulic Cylinder 2-1/2 x Clevis Cap 2.5-3/4 ORB Rod Cap /4 ORB Piston S Hall W/Ring Rod Cyl A Cylinder Tube Rod,Tie 3/8 x Thread Lock Rod Clevis Sc Sckt Set 3/8UNC x 1/2 Knur Hex Nut 3/8-16 Gr Locknut TLM 3/4 NF PLC O-Ring Plug,3/4-16 UNF,Socket Seal Kit For 8727A & 8728A Cyl D-10

67 HOSE KIT Rear Remote Outlets with Male Quick Couplers Hose, 1/2 x 170" Strap, Rubber Strap, Adjustable Tie Coupler, Male E-1

68 HOSE KIT Rear Remote Outlets without Male Quick Couplers Hose, (3/4 JIC x 1/2 NPT) 1/2 x 170" Strap, Rubber Strap, Adjustable Tie E-2

69 HOSE KIT Massey Ferguson - 360, 360 Utility, 362, 375, Hose, 1/2 x 170" Strap, Rubber Strap, Adjustable Tie Valve, Relief Cartridge, Relief Fitting, Tee, 9/16-18 JIC x 9/16-18 JIC, Swivel Fitting, Adapter, 3/4-16 x 9/ Hose, 1/4 x Fitting, Adapter, 3/4-16 x 9/16-18, Swivel E-3

70 HOSE KIT Case IH - JX1080U, JX1090U & JX1100U New Holland - see Price Sheet for Models Hose, 1/2 x 150" Strap, Adjustable Tie Coupler, Male, 1/ E-4

71 HOSE KIT Case IH - JX1080U, JX1090U & JX1100U New Holland - see Price Sheet for Models Fitting, Adapter, 18mm-1.50 x 1/2 NPT Coupler, Male, 1/ Coupler, Female, 1/ Hose, 1/2 x Hose, 1/2 x Fitting, Elbow, 1/2-14 NPT x 1/2-14 NPT, Fitting, Elbow, 1/2-14 NPT x 1/2-14 NPT, Fitting, Adapter, 1/2-14 NPT x 1/2-14 NPT Tarp Strap Spiral Band, 1 Inch, Blue Spiral Band, 1 Inch, Red Spiral Band, 1 Inch, Yellow Spiral Band, 1 Inch, Green E-5

72 HOSE KIT New Holland - see Price Sheet for Models Hose, 3/8 x Fitting, Adapter, 1/ Strap, Adjustable, 1/2 x Sleeve, Nylon Dust Cap (Red) Dust Cap (Blue) Dust Cap (Yellow) Dust Cap (Green) Spiral Band, 1", Plastic, Blue Spiral Band, 1", Plastic, Red Spiral Band, 1", Plastic, Yellow Spiral Band, 1", Plastic, Green E-6

73 HOSE KIT New Holland - see Price Sheet for Models Hose, 3/8 x Hose, 3/8 x Fitting, Adapter, 1/ Sleeve, Nylon Strap, Adjustable, 1/2 x Spiral Band, 1", Plastic, Blue Spiral Band, 1", Plastic, Red Spiral Band, 1", Plastic, Yellow Spiral Band, 1", Plastic, Green Tarp Strap Dust Cap (Blue) Dust Cap (Red Dust Cap (Yellow) Dust Cap (Green) E-7

74 HOSE KIT John Deere - see Price Sheet for Models Hose, 3/8 x Sleeve, Nylon, 1-3/4 x Tarp Strap Strap, Adjustable Coupler, Male Spiral Band, Blue, 1" Spiral Band, Red, 1" Spiral Band, Yellow, 1" Spiral Band, Green, 1" Dust Cap, Blue Dust Cap, Red Dust Cap, Yellow Dust Cap, Green Spiral Band, Blue, 5/ Spiral Band, Red, 5/ Spiral Band, Yellow, 5/ Spiral Band, Green, 5/ E-8

75 HOSE KIT John Deere - see Price Sheet for Models Hose, 3/8 x Sleeve, Nylon, 1-3/4 x Tarp Strap Strap, Adjustable Coupler, Male Spiral Band, Blue, 1" Spiral Band, Red, 1" Spiral Band, Yellow, 1" Spiral Band, Green, 1" Dust Cap, Blue Dust Cap, Red Dust Cap, Yellow Dust Cap, Green Spiral Band, Blue, 5/ Spiral Band, Red, 5/ Spiral Band, Yellow, 5/ Spiral Band, Green, 5/ E-9

76 HOSE KIT New Holland - see Price Sheet for Models 1-37E-10

77 HOSE KIT New Holland - see Price Sheet for Models Fitting, Adapter, Straight, 3/4-16 SAE Male x Metric Male Fitting, Adapter, Straight, 3/4-16 JIC Male x Metric Male Fitting, Elbow, 90, 3/4-16 O-Ring To 3/4-16 JIC Coupler, Quick, Female, 1/2" (3/4-16 SAE) Hose, 3/8 x 70" Sleeve, Nylon Hose, 1-1/4 I.D. x 76" Strap, Adjustable, 1/2 x Dust Plug, Red Dust Plug, Blue Dust Plug, Yellow Dust Plug, Green Fitting, Elbow, 90, "Street," 1/2-14 NPT x 1/2-14 NPT Fitting, Adapter, Straight, 3/4-16 JIC Female x 3/4-16 SAE Male Dust Cap, Red Dust Cap, Blue Dust Cap, Yellow Dust Cap, Green Strap, Tarp Coupler, Quick, Male, 1/ E-11

78

79 VALVE KIT Case IH - 595, 695 & 895 FWA Valve, Prince, HC-V-K2 (Includes Single Control Handle) Bracket, Valve Mounting Fitting, Elbow, 7/8-14 x 1 1/ Fitting Adapter O-Ring 7/8-14 x 1/2 NPT Coupler, Female Quick Attach 1/ Capscrew, 3/8-16 x Locknut, 3/ Strap, Rubber Strap, Adjustable Fitting, Adapter, 1/2 NPTF x 1/2 NPSM Coupler, Quick Attach, Male 1/ Band, Spiral, Blue Band, Spiral, Red Band, Spiral, Yellow Band, Spiral, Green Hose, 3/8 x 130" Decal, Joystick Control F-1

80 VALVE KIT John Deere , 5300 & F-2

81 VALVE KIT John Deere , 5300 & Valve, Prince, HC-V-K2 (Includes Single Control Handle) Bracket, Valve Mounting Fitting, Elbow, 7/8-14 x 1 1/ Fitting, Adapter, Straight, 7/8-14 x 11/ Fitting, Elbow 7/8-14 JIC 7/8-14 JIC Fitting, Adapter, Power Beyond Fitting Adapter O-Ring 7/8-14 x 1/2 NPT Coupler, Female Quick Attach 1/ Hose, 1/2 x 84" Capscrew, 3/8-16 x Locknut, 3/ Strap, Rubber Strap, Adjustable Fitting, Elbow, 7/8-14 JIC x 22mm-1.5mm Metric O-Ring Fitting, Straight. 7/8-14 JIC x 22mm-1.5mm Metric O-Ring Capscrew, 1/2-13 x 2-1/ Flatwasher, 1/ Fitting, Adapter, 1/2 NPTF x 1/2 NPSM Coupler, Quick Attach, Male 1/ Band, Spiral, Blue Band, Spiral, Red Band, Spiral, Yellow Band, Spiral, Green 2 21 G Plug, Pipe, NPTF 3/8-18 Hex Socket Hose, 3/8 x 130" Decal, Joystick Control Locknut, 1/ F-3

82 VALVE KIT Massey Ferguson & F-4

83 VALVE KIT Massey Ferguson & Valve, Prince, HC-V-K2 (Includes Single Control Handle) Bracket, Valve Mounting Fitting, Elbow, 7/8-14 x 1 1/ Fitting Adapter O-Ring 7/8-14 x 1/2 NPT Coupler, Female Quick Attach 1/ Capscrew, 3/8-16 x Locknut, 3/ Strap, Rubber Strap, Adjustable Fitting, Adapter, 1/2 NPTF x 1/2 NPSM Coupler, Quick Attach, Male 1/ Band, Spiral, Blue Band, Spiral, Red Band, Spiral, Yellow Band, Spiral, Green Hose, 3/8 x 96" Decal, Joystick Control Fitting, Adapter, 7/8-14 x 1-1/16-12, Straight Hose, 1/2 x Hose, 1/2 x Hose, 1/2 x Fitting, Elbow, 7/8-14 x 7/8 x 14, Capscrew, 1/2-13 x 2-1/ Flatwasher, 1/ Locknut, 1/ Fitting, Power Beyond Fitting, Swivel, Adapter, F-5

84 VALVE KIT John Deere , 2355, 2550 & F-6

85 VALVE KIT John Deere , 2355, 2550 & Valve, Prince LVR (2500 PSI) Bracket, Valve Mounting Handle, Standard Angle, Decal Mounting Plate, Valve Mounting Capscrew, 5/16-18 x 3/ Lockwasher, 5/ Ball, Handle Tarp Strap Hose, 1/2 x Hose, 3/8 x Nylon Sleeve Capscrew, 3/8-16 x 2-1/ Locknut, 3/ Coupler, Female Spiral Band, Plastic, Blue, 1 1 * Spiral Band, Plastic, Red, 1 1 * Spiral Band, Plastic, Yellow, 1 1 * Spiral Band, Plastic, Green, Capscrew, 1/2-13 x 2-1/ Plug, 3/4-16 O-Ring Locknut, 1/ Decal, Single Handle Control Hex Nut, 7/ Strap, Adjustable Fitting, Adapter, 3/4-16 O-Ring x 3/8 NPT Boot Coupler, Male Spiral Band, Plastic, Blue 5/8 1 * Spiral Band, Plastic, Red 5/8 1 * Spiral Band, Plastic, Yellow 5/8 1 * Spiral Band, Plastic, Green 5/ F-7

86 VALVE KIT (PART 1) New Holland - see Price Sheet for Models 1-37F-8

87 VALVE KIT (PART 1) New Holland - see Price Sheet for Models * Hose, 1/2 x 54.00", 3/4-16 JIC, Female, Swivel (Both Ends) 1 * Hose, 1/2 x 72.00", 3/4-16 JIC, Female, Swivel (Both Ends) 1 * Hose, 1/2 x 48.00", 3/4-16 JIC Male x 3/4-16 JIC Female, Swivel Fitting, Elbow, 3/4-16 O-Ring x 3/4-16 Flare x Fitting, Straight, 1-3/8-12 UNF x 1/2-14 NPT Fitting, Tee, Street, 1/2-14 x 1/2-14 x 1/2-14 NPT Fitting, Elbow, 1/2-14 NPT x 3/4-16 Flare x G Fitting, Plug, 1/2-14 NPT Spacer,.50 Thick x 1.5 Wide x 4.50 Long Hose, 1/2 x 39", 1/2-14 NPT x 3/4-16 JIC Hose, 1/2 x 120", 1/2-14 NPT x 3/4-16 JIC Female Swivel Coupler, Male Quick Band, Spiral, 1, Blue Band, Spiral, 1, Red Band, Spiral, 1, Yellow Band, Spiral, 1, Green Strap, Reusable Tie, 3/16 x Strap, Rubber Tie Adapter (Used With 7/8-14 JIC Oil Lines Only) Fitting, Elbow 3/4-16 O-Ring x 3/4-16 Flare Hose, 1/2 x 14", 1/2-14 NPT x 3/4-16 JIC Hose, 1/2 x 39", 3/4-19 JIC, Female Swivel (Both Ends) F-9

88 VALVE KIT (PART 2) New Holland - see Price Sheet for Models 1-37F-10

89 VALVE KIT (PART 2) New Holland - see Price Sheet for Models * Valve, DFP Model 1627 JE 1 * Angle, Handle Attachment 1 * Screw, Flat Head Socket, 5/16-24 x 3/4 1 * Screw, Socket Head Cap, 5/16-24 x 3/4 1 * Lever, Valve Handle 1 * Ball Joint, Male 2 * Ball Joint, Female 1 * Stud, Ball Joint 1 * Screw, Socket Head Cap, 1/4-28 x 3/4 3 * Flatwasher, 1/4 3 * Lockwasher, 1/4 2 * Hex Nut, 1/ * Locknut, 1/ * Fitting. Power Beyond Sleeve 1 * Elbow, 9/16 SAE x 3/4 JIC x 90 1 * Hose, 3/8 x 6 7/8 Long 1 * Hose, 3/8 x 7 7/8 Long 1 * Hose, 3/8 x 8 1/2 Long 1 * Hose, 3/8 x 13 Long 1 * Box, Valve Mounting 1 * Cover, Valve Box 1 * Capscrew, 1/4-20 x 2 2 * Locknut, 1/ * Spacer, Quick Coupler 4 * Spiral Band,Plastic-Blue-1" ID Spiral Band,Plastic-Red- 1" ID Spiral Band,Plastic-Yel-1" ID Spiral Band,Plastic-Green-1"ID 4 * Quick Coupler (F) 4 * Panel, J-Clip 2 * Boot 1 * Cap Nut 1 * Knob, Valve Handle 1 * Screw, Pan Head, Type AB, #10-16 x 1/2 2 *32 G Fitting, Reducer Bushing, 1/2 NPT x 3/8 NPT 4 * Dust Cap, 1/2 4 * Hose, 1/2 x 54.00", 3/4-16 JIC, Female, Swivel (Both Ends) 1 * Hose, 1/2 x 72.00", 3/4-16 JIC, Female, Swivel (Both Ends) 1 * Hose, 1/2 x 48.00", 3/4-16 JIC Male x 3/4-16 JIC Female, Swivel 1 * Fitting, Straight, 9/16-18 x 3/ * Fitting, 45 3/4-16 JIC 1 * Bracket, Valve Mounting 1 * Capscrew, 3/8-16 x 2-1/4 2 * Locknut, 3/ Capscrew, 3/4-10 x Lockwasher, 3/ Spacer,.50 Thick x 1.5 Wide x 4.50 Long Decal, Valve Operation Hose, 1/2 x 12", 3/4-16 JIC, Female Swivel (Both Ends) (Not Shown) Used In Optional 2 Two Pump Hydraulics Kit ( ) * Items 1 thru 41 have been pre-assembled 1-37F-11

90 VALVE KIT Massey Ferguson & F-12

91 VALVE KIT Massey Ferguson & 383 NO. NO. DESCTIPTION QTY Valve, Prince LVR (2500 PSI) Bracket, Valve Mounting Handle, Standard Angle, Decal Mounting Decal, Single Handle Control Capscrew, 5/16-18 x 3/ Lockwasher, 5/16 TCP Ball, Handle Fitting, Elbow 3/4-16 JIC x 3/4-16 O-Ring, Hose, 1/2 x 120 (Power Beyond) Hose, 1/2 x 104 (Pressure) Hose, 1/2 x 96 (Tank) Hex Nut, 7/ Boot Coupler, Female Spiral Band, Plastic, Blue Spiral Band, Plastic, Red Spiral Band, Plastic, Yellow Spiral Band, Plastic, Green Capscrew 1/2-13 x 2-1/ Flatwasher, 1/ Locknut, 1/ Hose, 3/8 x Strap, Adjustable Fitting, Adapter 3/4-16 O-Ring x 3/8 NPT Coupler, Male Spiral Band, Plastic, Blue 5/ Spiral Band, Plastic, Red 5/ Spiral Band, Plastic, Yellow 5/ Spiral Band, Plastic, Green 5/ F-13

92 VALVE KIT Case IH - C50 & C60 ROPS 1-37F-14

93 VALVE KIT Case IH - C50 & C60 ROPS Valve, Prince LVR (2500 PSI) Capscrew, 3/8-16 x 2-1/ Handle, Standard Angle, Decal Mounting Locknut, 3/ Capscrew, 5/16-18 x 3/ Lockwasher, 5/ Ball, Handle Plug, 1-1/ Hose, 3/8 x 78 (Pressure) Fitting, Adapter, 1 3/16-12 ORB x 7/8-14 JIC Elbow, 90 7/8 JIC Hex Nut, 7/ Boot Coupler, Female Spiral Band, Plastic, Blue, Spiral Band, Plastic, Red, Spiral Band, Plastic, Yellow, Spiral Band, Plastic, Green, Hose, 3/8 x Spiral Band, Plastic, Blue, 5/ Spiral Band, Plastic, Red, 5/ Spiral Band, Plastic, Yellow, 5/ Spiral Band, Plastic, Green, 5/ Coupler, Male Decal, Single Handle Control Strap, Adjustable Fitting, Adapter, 3/4-16 O-Ring x 3/8 NPT Plate, Valve Mounting Tube, Valve Mounting Flatwasher, 1/ Capscrew, 1/2-13 x 2-1/ Cap, 7/8-14 JIC Hose, 3/8 x 72 (Tank) Locknut, 1/ F-15

94 VALVE KIT New Holland - TT55 & TT F-16

95 VALVE KIT New Holland - TT55 & TT Valve, Prince LVR (3000 PSI) Capscrew, 3/8-16 x 2-1/4, Grade Handle, Valve, Standard * Bracket, Decal Mounting Plate Locknut, 3/8-16, Type N Capscrew, 5/16-18 x 3/4 Grade Lockwasher, 5/ Ball, Handle * Fitting, Elbow, 90, 3/4-16 JIC x 3/4-16 SAE O-Ring Strap, Adjustable, 1/2 x Hose, 1/2 x 96 (Tank) Hose, 1/2 x 78 (Power Beyond) Hex Nut, 7/16-20 * Boot, Rubber, Valve Handle * Coupler, Quick, Female, 3/ Band, Plastic Identification, Blue, Band, Plastic Identification, Red, Band, Plastic Identification, Yellow, Band, Plastic Identification, Green, Hose, 1/2 x 48 (Loader Boom Oil Lines) Band, Plastic Identification, Blue, 5/ Band, Plastic Identification, Red, 5/ Band, Plastic Identification, Yellow, 5/ Band, Plastic Identification, Green, 5/ Coupler, Quick, Male, 3/ Decal, Single Handle Control Strap, Plastic Tie, 3/16 x Fitting, Straight Hex Nipple, 3/4-16 SAE Male x 3/4-16 SAE Male Plate, Valve Mounting Tube, Valve Mounting Fitting, Straight Adapter, 3/4-16 JIC x 22mm-1.5 Metric Flow Bolt, 22mm-1.5 Metric x 9/16-18 SAE Hose, 1/2 x 112 (Pressure) Capscrew, 1/2-13 x 2-1/ Flatwasher, 1/2 SAE Locknut, 1/2-13, Type-N Fitting, Straight Adapter, 9/16-18 SAE O-Ring x 3/4-16 JIC Sleeve, Hose, Nylon, 1-1/4 ID x 78 Long Sleeve, Hose, Nylon, 1-1/4 ID x 96 Long Sleeve, Hose, Nylon, 1-1//4 ID x 112 Long Sleeve, Hose, Nylon, 1-3/4 ID x 48 Long Lockwasher, 7/16 * F-17

96 VALVE KIT New Holland - see Price Sheet for Models 1-37F-18

97 VALVE KIT New Holland - see Price Sheet for Models Valve, Prince LVR (3000 PSI) Cable Assembly Joystick Assembly, Indemar Mount Plate, Valve Bracket, Joystick Mounting Capscrew, 5/16-18 x 3/4 YDP Lockwasher, 5/16 YDP Fitting, Elbow, 3/4-16 JIC x 3/4-16 O-Ring, Hose, 3/8 x 84 Tank Hose, 3/8 x 90 Pressure Hose, 3/8 x 60 Power Beyond Capscrew, 20mm-2.50mm x 65mm Lockwasher, 20mm Coupler, Quick, Female, 3/4-16 O-Ring YDP Dust Plug, Blue Dust Plug, Red Dust Plug, Yellow Dust Plug, Green Fitting, Straight, 3/4-16 O-Ring x 3/4-16 O-Ring Sleeve, Nylon, 1-1/4 x Sleeve, Nylon, 1-1/4 x Sleeve, Nylon, 1-1/4 x Fitting, Straight, 3/4 BSPP x 7/8-14 JIC Fitting, Elbow, 7/8-14 JIC x 7/8-14 JIC Fitting, Elbow, 3/4-16 JIC x 3/4-16 JIC Fitting, Straight, 18mm-1.5 x 3/4-16 JIC Strap, Adjustable.50 x Strap, Tarp Capscrew, 5/16-18 x 3-1/ Flatwasher, 5/ Capscrew, Hex Head, 5/16-18 x Locknut, 5/ Hose, 3/8 x Sleeve, Nylon, 1-1/4 x Coupler, Quick, Male Dust Cap, Blue Dust Cap, Red Dust Cap, Yellow Dust Cap, Green F-19

98 VALVE KIT Kubota - see Price Sheet for Models 1-37F-20

99 VALVE KIT Kubota - see Price Sheet for Models * Valve, Prince LVS, Series, 2-Spool (2500 PSI) 1 * Handle, Valve, Standard 1 * Hex Nut, 7/ * Lockwasher, 7/16 1 * Boot, Valve Handle Linkage 1 * Ball, Valve Handle Fitting, Elbow, 90, 9/16-18 SAE O-Ring Male x 9/16-18 JIC Female Fitting, Straight, 9/16-18 SAE O-Ring Male x 9/16-18 JIC Female Fitting, Straight, 3/8 NPT Male x 9/16-18 JIC Male Coupler, Female Quick, 3/ Spiral Band, Plastic, Blue, Spiral Band, Plastic, Red, Spiral Band, Plastic, Yellow, Spiral Band, Plastic, Green, Plate, Valve Mounting Spacer, Tube, 1 O.D. x 1/2 I.D. x 1-1/4 Long Tube, Valve Mounting Capscrew, 3/8-16 x 3-1/ Locknut, 3/ Plug, Square Tube Shield, Series Valve, With Decals Decal, Single Handle Control Decal, Warning: Do Not Tamper With Valve Relief Setting Decal, Lock/Unlock Capscrew, 5/16-18 x Capscrew, 5/16-18 x 3/ Lockwasher, 5/ Capscrew, 1/2-13 x 2-1/ Flatwasher, 1/ Locknut, 1/ Hose, 3/8 x 96, 9/16-18 JIC Female Swivel x 3/4-16 Str. Thd. With O-Ring Male Hose, 3/8 x 48, 3/4-16 JIC Female Swivel x 3/4-16 Str. Thd. With O-Ring Male Sleeve, Hose, 96 Long (For Tank Hose) Sleeve, Hose, 50 Long (For Pressure & Power Beyond Hoses) Fitting, Elbow, 90, 22mm-1.5 Male x 1/2-14 Male Fitting, Straight, 1/2 NPT Female x 3/4-16 JIC Male Fitting, Elbow, 90, 9/16-18 JIC Male x 1/2-14 NPTF Male Strap, Plastic, Adjustable, 3/16 Wide x 11 Long Hose, 3/8 x 72, 3/8 NPTF x 3/4 JIC Swivel (Loader Control) Sleeve, Hose, 76 Long (For Loader Control Hoses) Coupler, Male Quick, 3/ Spiral Band, Plastic, Blue, 5/ Spiral Band, Plastic, Red, 5/ Spiral Band, Plastic, Yellow, 5/ Spiral Band, Plastic, Green, 5/ Strap, Tarp 1 * Items 2 Through 6 Are Included With Valve, Item F-21

100 VALVE KIT Kubota - M4700 & M F-22

101 VALVE KIT Kubota - M4700 & M5400 * Valve, Prince LVS, Series, 2-Spool (2000 PSI) 1 * Handle, Valve, Standard 1 * Hex Nut, 7/ * Lockwasher, 7/16 1 * Boot, Valve Handle Linkage 1 * Ball, Valve Handle Fitting, Elbow, 90, 9/16-18 SAE O-Ring Male x 9/16-18 JIC Female Fitting, Straight, 9/16-18 SAE O-Ring Male x 9/16-18 JIC Female Fitting, Straight, 3/8 NPT Male x 9/16-18 JIC Male Coupler, Female Quick, 3/ Spiral Band, Plastic, Blue, Spiral Band, Plastic, Red, Spiral Band, Plastic, Yellow, Spiral Band, Plastic, Green, Plate, Valve Mounting Spacer, Tube, 1 O.D. x 1/2 I.D. x 1-3/4 Long Tube, Valve Mount Capscrew, 3/8-16 x Locknut, 3/ Plug, Square Tube Shield, Series Valve, With Decals Decal, Single Handle Control Decal, Warning: Do Not Tamper With Valve Relief Setting Decal, Lock/Unlock Capscrew, 5/16-18 x Capscrew, 5/16-18 x 3/ Lockwasher, 5/ Capscrew, 1/2-13 x 2-1/ Flatwasher, 1/ Lockwasher, 1/ Hose, 3/8x70 3/4 Str. /W O-Ring x 9/16 JIC Swivel (Pressure & Power Beyond) Hose, 3/8 x 40, 3/4 Str. /W O-Ring x 9/16 JIC Swivel (Tank) Sleeve, Hose, 76 Long Sleeve, Hose, 40 Long Fitting, Straight, 3/8 NPTF Male x 9/16 JIC Male Fitting, Elbow, 45, 9/16 JIC Female x 9/16 JIC Male Fitting, Elbow, 90, 1/2 NPT Male x 9/16 JIC Male Strap, Plastic, Adjustable, 3/16 Wide x 11 Long Hose, 3/8 x 50 3/8 NPTF Swivel Female x 3/4 JIC Swivel Male (Loader Control) Sleeve, Hose, 50 Long Coupler, Male Quick, 3/ Spiral Band, Plastic, Blue, 5/ Spiral Band, Plastic, Red, 5/ Spiral Band, Plastic, Yellow, 5/ Spiral Band, Plastic, Green, 5/8 1 * Items 2 Through 6 Are Included With Valve, Item F-23

102 VALVE KIT Kubota - see Price Sheet for Models 1-37F-24

103 VALVE KIT Kubota - see Price Sheet for Models * Valve, Prince LVS, Series, 2-Spool (3000 PSI) 1 * Handle, Valve, Standard 1 * Hex Nut, 7/ * Lockwasher, 7/16" 1 * Boot, Valve Handle Linkage 1 * Ball, Valve Handle Fitting, Elbow, 90, 9/16-18 SAE O-Ring Male x 9/16-18 JIC Female Fitting, Straight, 9/16-18 SAE O-Ring Male x 9/16-18 JIC Female Fitting, Straight, 3/8 NPT Male x 9/16-18 JIC Male Coupler, Female Quick, 3/8" Spiral Band, Plastic, Blue, 1" Spiral Band, Plastic, Red, 1" Spiral Band, Plastic, Yellow, 1" Spiral Band, Plastic, Green, 1" Plate, Valve Mounting Spacer, Tube, 1" O.D. x 1/2" I.D. x 3/4" Long Tube, Valve Mount Capscrew, 3/8-16 x 3" Locknut, 3/ Plug, Square Tube Shield, Series Valve, With Decals Decal, Single Handle Control Decal, Warning: Do Not Tamper With Valve Relief Setting Decal, Lock/Unlock Capscrew, 5/16-18 x 1" Capscrew, 5/16-18 x 3/4" Lockwasher, 5/16" Capscrew, 1/2-13 x 2-1/2" Flatwasher, 1/2" Locknut, 1/ Fitting, Straight, 3/4-16 JIC Male x 3/4-16 SAE O-Ring Male Hose, 3/8 x 90", 3/4-16 JIC Female Swivel, Both Ends (Tank) Hose, 3/8 x 72", 3/4-16 JIC Female Swivel x 3/8-18 NPTF Male (Pressure) Hose, 3/8 x 78", 3/4-16 JIC Female Swivel, Both Ends (Power Beyond) Sleeve, Hose, 90" Long Sleeve, Hose, 78" Long Fitting, Elbow, 45, 3/4-16 JIC Male x 3/8-18 NPTF Male Fitting, Elbow, 90, 3/4-16 JIC Male x 1/2-14 NPT Male Strap, Plastic, Adjustable, 3/16" Wide x 11" Long Hose, 3/8 x 44", 3/8 NPTF x 3/4 JIC Swivel (Loader Control) Sleeve, Hose, 44" Long Coupler, Male Quick, 3/ Spiral Band, Plastic, Blue, 5/8" Spiral Band, Plastic, Red, 5/8" Spiral Band, Plastic, Yellow, 5/8" Spiral Band, Plastic, Green, 5/8" 1 * Items 2 Through 6 Are Included With Valve, Item F-25

104 VALVE KIT Case IH - JX1080U, JX1090U & JX1100U ROPS or Cab New Holland - TL80A, TL90A & TL100A ROPS or Cab 1-37F-26

105 VALVE KIT Case IH - JX1080U, JX1090U & JX1100U ROPS or Cab New Holland - TL80A, TL90A & TL100A ROPS or Cab Valve, Prince LVR (Parallel), 3000 PSI Joystick Assembly, Cable Controlled Valve Cable Assembly Bracket, Mounting, Joystick, Cable-Controlled Valve Bracket, Decal Mounting, Joystick Operation Decal, Joystick Loader Operation Bracket, Mounting, Valve, Cable-Controlled, Under Platform Spacer, Round, 7/8 O.D. - 5/8 I.D. x 1-1/8 Long Clevis, Cable End Adapter, To Handle, 6mm-1.00 x 13mm Eff Thread Capscrew, 5/16-18 x 3-1/ Locknut, 5/ Capscrew, 5/16-18 x 3/ Lockwasher, 5/ Capscrew, 16mm-2.00 x 80mm Lockwasher, 5/ Capscrew, 10mm-1.5 x 60mm Lockwasher, 7/ Fitting, Elbow, 90, 1/2-14 Female x 1/2-14 Male Coupler, Quick, Female Coupler, Quick, Male Fitting, Straight, 3/4-16 SAE O-Ring Male x 1/2-14 NPT Male Fitting, Elbow, 90, 7/8-14 JIC Male x 3/4-16 SAE O-Ring Male Fitting, Elbow, 90, 7/8-14 JIC Male x 1-1/16-12 JIC Female Swivel Dust Plug, Quick Coupler, Red Dust Plug, Quick Coupler, Blue Dust Plug, Quick Coupler, Yellow Dust Plug, Quick Coupler, Green Band, Plastic Spiral, Color Identification, 1, Red Band, Plastic Spiral, Color Identification, 1, Blue Band, Plastic Spiral, Color Identification, 1, Yellow Band, Plastic Spiral, Color Identification, 1, Green Hose, 1/2 x 42 (Power Beyond) Hose, 1/2 x 54 (Pressure) Hose, 1/2 x 60 (Tank) Hose, 1/2 x 63 (Loader Control) Sleeve, Nylon Hose, 1-1/4 x Sleeve, Nylon Hose, 1-1/4 x Sleeve, Nylon Hose, 1-1/4 x Sleeve, Nylon Hose, 2 x Strap, Plastic Tie, Adjustable, 1/2 x Strap, Tarp, Rubber With S-Hooks F-27

106 VALVE KIT Universal - ROPS Cab Open Center w/power Beyond Sleeve 1-37F-28

107 VALVE KIT Universal - ROPS Cab Open Center w/power Beyond Sleeve Valve, Loader Control, 2-Spool, 3000 PSI, Parallel Cable Assembly, Push-Pull, 50 Nominal Length Control Handle Assembly, Single Joystick, Dual Axis, Cable Coupler, Quick, Male, 3/8 Nominal, 3/8-18 Female Threads Coupler, Quick, Female, 3/8 Nominal, 3/8-18 Female Threads Pedestal, Control Handle Stand Hose, 3/8 x 44, 3/8 NPTF x 3/4-16 JIC Female Swivel Band, Plastic Spiral, Color Identification, 5/8, Blue Band, Plastic Spiral, Color Identification, 5/8, Red Band, Plastic Spiral, Color Identification, 5/8, Yellow Band, Plastic Spiral, Color Identification, 5/8, Green Band, Plastic Spiral, Color Identification, 1, Blue Band, Plastic Spiral, Color Identification, 1, Red Band, Plastic Spiral, Color Identification, 1, Yellow Band, Plastic Spiral, Color Identification, 1, Green Fitting, Straight, 3/4-16 SAE O-Ring Male x 3/8-18 NPT Male Sleeve, Nylon Hose, 44 Long Strap, Tie, Plastic, Adjustable 3/16 x Capscrew, Hex Head, 5/16-18 x 3-1/2, Grade Flatwasher, 5/16 N-SAE Locknut, 5/16-18, Type N Plate, Valve Mounting, Bolt-On Plug, Plastic, Square Tube Dust Plug, Black, 3/8 Quick Coupler Fitting, Straight, 3/4-16 SAE O-Ring Male x 7/8-14 JIC Male Fitting, Elbow, 90, 7/8-14 JIC Female Swivel x 7/8-14 JIC Male Strap, Rubber, Tarp, With Hooks, 19 Long Capscrew, Hex Head, 5/16-18 x 3/4, Grade Lockwasher, 5/ Capscrew, Hex Socket, 1/4-20 x 3/ Clevis, Cable End Adapter, To Handle, 6mm-1.00 x 13mm Eff Thread Plug, Power Beyond, Open Center Fitting, Elbow, 90, 3/4-16 SAE O-Ring Male x 3/4-16 JIC Male F-29

108 VALVE KIT John Deere - see Price Sheet for Models 1-37F-30

109 VALVE KIT John Deere - see Price Sheet for Models Valve, Prince LVR (2500 PSI) Capscrew, 3/8 x 2-1/ Handle, Standard Angle, Decal Mounting Locknut, 3/ Capscrew, 5/16 x 3/ Lockwasher, 5/ Ball, Handle Fitting, Elbow, 7/8-14 JIC x 3/4 O-Ring, Fitting, Elbow, 7/8-14 JIC x 7/8 x 14 JIC, Hose, 1/2 x 96 (Power Beyond) Hose, 1/2 x 96 (Tank & Pressure) Hex Nut, 7/ Boot Coupler, Female Spiral Band, Plastic, Blue, Spiral Band, Plastic, Red, Spiral Band, Plastic, Yellow, Spiral Band, Plastic, Green, Hose, 3/8 x Spiral Band, Plastic, Blue, 5/ Spiral Band, Plastic, Red, 5/ Spiral Band, Plastic, Yellow, 5/ Spiral Band, Plastic, Green, 5/ Coupler, Male Decal, Single Handle Control Strap, Adjustable Fitting, Adapter, 3/4 O-Ring x 3/8 NPT Plate, Valve Mounting Bracket, Valve Mounting Fitting, Adapter, 7/8 x M ISO Capscrew, 20mm-2.50 x 65mm Lockwasher, 20mm Valve Mounting Tube Plug Capscrew, 1/2 x 2.75 Gr Hex Nut, 1/ Flatwasher, 1/ Nylon Sleeve Nylon Sleeve G Pipe Plug, NPTF 3/8-18 Hex Socket Adapter, Male Metric 1 1/16 x 27mm Elbow, 90 7/8-1/4 JIC x 1 1/16 JIC Swivel F-31

110 VALVE KIT New Holland - TT60A & TT75A 1-37F-32

111 VALVE KIT New Holland - TT60A & TT75A Valve, Prince Hose 0.375ID x 78 (Tank) Hose 0.375ID x 85 (Power Beyond) Hose 0.375ID x 42 (Pressure Non-Aux) Hose 0.375ID x 42 (Pressure Non-Aux) Hose 0.375ID x 76 (Pressure Aux) (Not Shown) Hose #6-6MB-8FJX - 50 (Loader Lines) Hose #6-6MB-8FJX - 53 (Loader Lines) Plate, Valve Mounting Tube, Valve Mounting Sleeve, Hose, Nylon,1-1/4 ID x 78 Long Sleeve, Hose, Nylon,1-1/4 ID x 86 Long Sleeve, Hose, Nylon,1-1/4 ID x 50 Long Sleeve, Hose, Nylon,1-1/4 ID x 54 Long Sleeve, Hose, Nylon,1-1/4 ID x 76 Long (Not Shown) Sleeve, Hose, Nylon,1-1/4 ID x 42 Long Flow Bolt M x 2.56 (Non-Aux) Flow Bolt M x 1.56 (Aux) (Not Shown) Adapter, 8MB-6MJ Long Adapter, 9/16 JIC x 3/4 O-Ring Fitting, 9/16 O-Ring x 9/16 JIC Swivel Coupler, 3/8 Female Coupler, 3/8 Male Dust Plug, Dust Cap, Elbow Tee Elbow, 7/8 JIC x 7/8 JIC Swivel Band, Plastic Identification, Blue, 5/ Band, Plastic Identification, Red, 5/ Band, Plastic Identification, Yellow, 5/ Band, Plastic Identification, Green, 5/ Strap, Adjustable,1/2 x Strap, Plastic Tie, 3/16 x Capscrew, 5/16-18 x.75, Grade Lockwasher, 5/ Capscrew, 3/8-16 x 2-1/4, Grade Locknut, 3/8-16, Type N Capscrew, 1/2-13 x 2-1/ Flatwasher, 1/2 SAE Locknut,1/2-13,Type-N Flatwasher, 3/ F-33

112 SPOOL MONO-BLOCK VALVE ASSEMBLY 1 N/A Body, 2 Spool Valve (See Note) 1 2 N/A Spool (See Note) 2 3 * 114 O-Ring 4 4 * 908 O-Ring Back-Up 1 6 * 014 O-Ring 1 7 * 906 O-Ring Plug, Load Check Spring, Load Check Poppet, Load Check Kit, Seal, Includes * Items Plug, Relief Plug, 1/4-NPTF Pipe 1 Note: 1. These Are Matched Parts And Not Sold As Service Parts. 1-37F-34

113 SPRING CENTER FLOAT DETENT & REGEN ASSEMBLY 1 * Spacer 1 2 * Cup, Stop 1 3 * Spring 1 4 * Washer 1 5 * Retainer, Detent 1 6 * Ball, Steel 2 7 * Spring 1 8 * Poppet 1 9 * Screw, Cap 2 10 * Cap, End 1 11 * Sleeve, Float Detent (A-B Spool) 1 12 * Retainer 1 13 * Sleeve, Regen (C-D Spool) Kit, Spring Center With Float Detent, Includes All Items Except Kit, Spring Center With Regen, Includes All Items Except F-35

114 SPRING CENTER ASSEMBLY NO. NO. DESCRIPTION QTY 1 * Cup, Stop 1 2 * Spring 1 3 * Cup, Stop 1 4 * Adapter, Spool 1 5 * Cap, End 1 6 * Capscrew Kit, Spring Center, Includes * Items F-36

115 JOYSTICK ASSEMBLY 1 * Clevis, Spool Lock 1 2 * Plate, Adapter Stud, Spool End, Rod 1 5 * Capscrew Assy, Rod End 2 7 * Hex Nut 3 8 * Capscrew 2 9 * Capscrew 1 10 * Flatwasher Kit, Spool Lock Hardware Kit, Bent Handle Kit, Straight Handle Kit, Boot/Cable Tie Adapter, Float Spool Adapter, Regen Spool Kit, Sub-Assy, Includes Items F-37

116 JOYSTICK AND CABLE HARNESS 1-37F-38

117 JOYSTICK AND CABLE HARNESS Handle, Plastic, Joystick Setscrew, 6mm-1.00 x 8mm Long Boot, Handle Linkage, Cable-Control Joystick 1 4 * Handle, Cable Control Joystick 1 5 * Retaining Ring, External 15/ * Rod End, Single 1 7 * Rod End, Double Bolt, Pan Head Slotted, 6mm-1.00 x 22mm Long 1 9 * Clevis, Cable Control Handle 1 10 ** Locknut, Nylon Insert, 6mm Base, Cable Control, With Lock Mechanism Lockwasher, 1/4" Capscrew, Socket Head, 6mm-1.00 x 30mm Cable Tie, 3/16 (Not Available As Separate Repair Part*) Cable Adapter Cable (Not Available As Individual Service Part, See Item 26) Jam Nut, 3/ Lockwasher, Internal Tooth, 3/4" Nut, Knurled, 3/ Strap, Valve Adapter Jam Nut, 5/ Pin, Cotter, 3/32 x 3/ Pin, Clevis, 5/16 x Clevis, Spool, For Cable Control Capscrew, Socket Head, 1/4-20 x 3/ Cable Assembly, 80 (Includes Items 16, 17, 18, 19, 20, 21, 22, 23 & 24) 1 27 ** Pin, 1/ ** Retaining Ring, External, 1/ ** Capscrew, Socket Head, 6mm-1.00 x 75mm * Kit, Handle Assy Repair (Includes Items 4-7 & 9) ** Kit, Pin/Cable Retainer (Includes Items 10 & 27-29) Joystick Assembly (Includes Items 1-14 & 27-29) F-39

118

119 GRILL GUARD KIT New Holland 00, 10 & 30 Series Grille Protector, Assembly Strut Angle Bushing, 3/ Locknut, 1/ Capscrew, 1/2-13 x 1-1/ Capscrew, 3/4-10 x 2-1/ Lockwasher G-1

120 GRILL GUARD KIT New Holland 35 Series Guard, Grille, Assembly Bracket, Grille Guard Strut Spacer, 1/4 x 2-1/ Spacer, 3/4 x 2-1/ Bearing, Rotation, 5/8 x 7/ Spacer, 7/8 x 3/ Flatwasher, 1/2 (Use With Mount Kit) Capscrew, 1/2-13 x 1-1/ Pin, Clevis Lockwasher, 7/ Capscrew, mm x 80mm Cotter, Hair Pin Locknut, 1/ G-2

121 GRILL GUARD KIT Kubota M Grille Guard Assembly Capscrew, 16mm-1.5mm x 35mm Lockwasher, 5/ Capscrew, 9/16-12 x Locknut, 9/ Flatwasher, 9/ G-3

122 GRILL GUARD KIT Kubota M4800SU, M4700, M4900, M5400 & M Grille Guard Assembly Capscrew, 16mm-1.5mm x 35mm Lockwasher, 5/ Capscrew, 1/2-13 x 2-1/ Locknut, 1/ Flatwasher, 1/ G-4

123 GRILL GUARD KIT Case IH C50, CX50, C60 & CX Grille Guard Stabilizer Tube, Grille Guard Spacer, Round Capscrew, 20mm-2.50 x 50mm, Class Capscrew, 20mm-2.50 x 40mm, Class Capscrew, 1/2-13 x 2-1/2", Grade Lockwasher, 20mm Flatwasher, 1/2", N-SAE Locknut, 1/2-13, Type N G-5

124 GRILL GUARD KIT New Holland TL70, TL80, TL90 & TL Capscrew, 1/2-13 x 1-1/ Flatwasher, 1/ Spacer, Tube Spacer Capscrew, 20mm-2.50 x 60mm Lockwasher, 20mm Bracket, Lower Support Grille Guard Assembly Locknut, 1/ G-6

125 GRILL GUARD KIT New Holland TT55 & TT Mounting Plate, Grille Guard, Left Mounting Plate, Grille Guard, Right Grille Guard Capscrew, 1/2-13 x 1-1/2", Grade Flatwasher, 1/2", N-SAE Locknut, 1/2-13, Type N Spacer Tube, 0.75 O.D " I.D. x 17/32" Capscrew, 16mm-1.5 x 40mm, Class Lockwasher, 5/8" Pin, Clevis, 1/2" x 2" Pin, Hair, Cotter, Ø.148" x 2.69" 2 * Flatwasher, 5/8", W-STD G-7

126 GRILL GUARD KIT Case IH JX1080U, JX1090U & JX1100U New Holland TL80A, TL90A & TL100A Grille Guard Bracket, Grille Guard Support, Left Bracket, Grille Guard Support, Right Spacer, Plate Spacer, Tube Capscrew, 20mm-2.50 x 50mm Capscrew, 1/2-13 x 1.50, Grade Lockwasher, 20mm, Grade Flatwasher, 1/ Locknut, 1/ G-8

127 GRILL GUARD KIT New Holland TT60A, TT75A Wdmt, Grille Guard Mount Plate, Left Mount Plate, Right Lockwasher 5/ Capscrew, 1/2-13 x 1-1/2 Grade Locknut, 1/2-13, Type-N Pin, Hair, Cotter.148 x Pin, Clevis, 1/2 x Flatwasher, 1/2 N-SAE Capscrew, 16mm-1.50 x 40mm, Class Tube, Spacer,.75 O.D. x.51 I.D Flatwasher, 5/8, W-STD G-9

128

129 DECALS - PLACEMENT Decal, Bush Hog Decal, Model D468 Decal, Danger-Multi-Hazard Decal, Warning, Oil leaks Decal, Push Lock, Pull Unlock Decal, Single Handle Control 1 7 D469 Decal, Warning-General Safety 1 8 D471 Decal, Warning-Injury or Death Decal, Danger, Rops/Seat Belt Emblem, SMV Canister Assy Manual, Operators H-1

130 DECALS - PICTORIALS Decal, Bush Hog Decal, Model Decal, Warning, Oil Leak Decal, Push lock, Pull Unlock 1 5 D469 Decal, Warning-General Safety Decal, Single Handle Control Decal, Danger, ROPS/Seat Belt 1 8 D468 Decal, Danger-Multi-Hazard 2 9 D471 Decal, Warning-Injury or Death H-2