AMR658 / AF029 Issue date: Product Data FASSON Transfer PET white PT / S8001 / BG42WH

Transcription

1 Facestock A gloss white polyester film with print treated surface for enhanced ink adhesion. Basis weight: 71 g/m² ISO 536 Caliper: 0,050 mm ISO 534 Adhesive S8001 is a permanent acrylic adhesive with good initial tack and high ultimate adhesion onto a variety of substrates including apolar plastics and lacquers. It also offers good resistance to solvents and cleaners. Type: Emulsion acrylate Coat weight: 27 g/sqm Initial Tack: 480 N/m FTM 9 glass Peel Adhesion: 420 N/m FTM 2 steel 24 hrs. Min. application temperature: +5 C Min. service temperature: -40 C Max. service temperature: +150 C Liner BG42 white: siliconized glassine paper, wood-free, super calandered and extremely tough and tearrestistent despite its thinness. Without back imprint. Basis weight: 65 g/m² ISO 536 Caliper: 0,058 mm ISO 534 Transparency: 48 % DIN Tensile Strength MD: 105 N/15mm ISO This liner is not recommended for fanfolding. Total construction caliper 0,135 mm Applications and use Transfer PET white PT / S8001 is specifically developed for labelling electronic, home appliance and other electrical items due to its good bonding performance and low ooze on a wide range of polar and apolar surfaces including metals, polycarbonate, ABS and polypropylene. Thanks to the special coating, printed labels for information, tracking and compliance can be created by thermal transfer and conventional print. For special requirements we strongly recommend application tests. Printing and conversion In addition to thermal transfer printing (for further information please see appendix) the product can also be printed by all conventional roll label techniques, such as flexo, UV letterpress, silkscreen. Specific testing is required. For easy diecutting sharp corners should be avoided. UL approval This product is UL recognized for indoor and outdoor use, the file number is MH For specific information on approved conditions, see appendix 2. RoHS / Regulation 2002/95/EU The substances listed in article 4 lid 1 of 2002/95/EU (RoHS) are not intentionally used in this product. The concentration limits of these substances will not exceed the set maximum concentration limits as provided in the proposed amendment for 2002/95/EU. Shelf life Two years when stored at 22 C and 50 %rh. Typical Values Typical values, not for specification use: see Appendix 1. 1/5

2 Appendix 1: Performance Data Note: the following technical data should be considered representative or typical only and should not be used for specification purposes. Peel Adhesion: FTM1: 180, 300 mm/min, dwell time: 48 hours Surface N/25mm ABS 13,0 Aluminium 11,5 Automotive lacquered panels 10,5 Glass 12,0 HDPE 7,5 LDPE 8,0 PA6 10,5 Stainless Steel 15,0 Chemical Resistance: The performance results are based on 4 hours immersions at room temperature unless otherwise noted. Samples were applied to the test panel and conditioned for 24 hours before immersion and evaluated immediately upon removal. Peel adhesion was measured according to FTM1. Chemical Test Substrate N/25mm Visual appearance Edge Penetration (mm) Ad blue 1 Aluminium 11,5 No change 0 Biodiesel Glass 11,0 No change 0 Bioethanol E85 2 Glass 11,5 No change 2 Brake Fluid 3 Glass 11,0 No change 0 Diesel 4 Glass 11,0 No change 0 Engine Oil 5 Glass 11,5 No change 0 Gasoline 6 Glass 8,0 No change 3 Heptane Glass 10,0 No change 3 Water, distilled Aluminium 7,5 No change 0 All purpose cleaner 7 Glass 8,5 No change 0 Bathroom cleaner 8 Glass 9,0 No change 0 Bleach 9 Glass 7,5 No change 0 Dishwashing detergent 10 Glass 9,0 No change 0 1 Aral 2 CropEnergies CropPower85 3 DOT 4 Synthetic (One Way) 4 TOTAL 5 TOTAL quartz 700, 10 W 40 6 TOTAL Euro 95 7 Sagrotan sea breeze (Reckitt Benckiser) 8 Cillit Antikalk (Reckitt Benckiser) 9 Danklorix (Colgate Palmoliv) 10 Fairy lemon (Procter& Gamble) 2/5

3 Thermal Transfer Printing: Printability Physical Resistance Flat head printers (tests were performed with the printer Zebra XII 140):: Ribbon Settings speed energy Print Quality ANSI Grade Scratch resistance Tape resistance Armor AXR B Dai Nippon R A Dai Nippon R A Ricoh B110Cx A Near edge printers (tests were performed with the printer Avery TTX 450 Near Edge): Ribbon Settings Print Quality ANSI Grade Scratch resistance Tape resistance Armor AXR /s 0 D ++ o Armor AXR /s ++ C ++ - Ricoh B120 E 4 /s ++ C ANSI (American National Standards Institute) Grade: information about barcode quality A: excellent B: good C: acceptable D: readable with difficulty ++: excellent +: good o: acceptable -: poor Chemical Resistance The printed samples were wetted on the surface with a soft clean cotton cloth soaked in the test solution by wiping 10 times back and forth with light pressure. After 5 seconds they were dried with a clean dry soft cloth. After 15 minutes the evaluation took place. AXR7+ R300 R510 B110Cx AXR600 AXR800 B120 E Ad Blue Anti-Freeze Biodiesel Bioethanol E Brake fluid 4 - o Cleaner solvent 5 o Engine oil Gasoline Hard wax polish 8 - o Isopropanol o + + o - o - +: good (no change) o: acceptable (minor change, still readable) -: poor 1 Aral 2 Speedfrost "Speedfroil" 1:1 in water 3 CropEnergies CropPower85 4 ATE SL DOT 4 5 Caramba Cold Cleaner 6 BP 15 W-40 7 Super unleaded 8 Nigrin Hard Wax Polish 3/5

4 Appendix 2: Compliance Data UL Underwriters Laboratories File Number: MH27538 This material is UL recognized for exposure indoors and outdoors to high humidity or occasional exposure to water. Surface Minimum Maximum I I/O Temperature ( C) Temperature ( C) Acrylic paint X X Acrylic powder paint X X Alkyd paint X X Aluminum X X Epoxy paint X X Epoxy powder paint X X Galvanized steel X X Polyester paint X X Polyester powder paint X X Polyurethane powder paint X X Porcelain X X Stainless steel X X Melamine X X Nylon Polyamide X X Phenolic - Phenol Formaldehyde X X Polycarbonate X X Unsaturated polyester - thermoset X X Acrylonitrile butadiene styrene (ABS) X X Polybutylene terephthalate (PBT) X X Polyethylene (PE) X - Polyphenylene oxide/ether (PPOX) X X Polypropylene (PP) X X Polystyrene (PS) X X Polyvinyl chloride (PVC) X X I: indoors, I/O: indoors and outdoors The UL certification includes the printing with one or more of the following thermal transfer ribbons: Armor "AXR-7+","AXR600", DNP "R510", Ricoh "B110C", "B110CX", Sony "5075". 4/5

5 Warranty All statements, technical information and recommendations about AVERY DENNISON products are based upon tests believed to be reliable but do not constitute a guarantee or warranty. All AVERY DENNISON products are sold with the understanding that PURCHASER has independently determined the suitability of such products for its purposes. AVERY DENNISON products are warranted to be free of defects in material or workmanship for a period of one year from the date of shipment. Any product shown to the satisfaction of AVERY DENNISON within the time provided to be so defective shall be replaced without charge or AVERY DENNISON may issue credit in such amount as it deems reasonable however, in no event shall AVERY DENNISON be responsible for claims beyond the replacement value of the defective product or in any way liable or responsible for consequential or incidental damages. NO EXPRESS WARRANTIES AND NO IMPLIED WARRANTIES, WHETHER OF MERCHANTIBILITY OR FITNESS FOR ANY PARTICULAR USE, OR OTHERWISE, EXCEPT AS SET FORTH ABOVE (WHICH IS MADE EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES) SHALL APPLY TO PRODUCTS SOLD BY AVERY DENNISON. AVERY DENNISON SPECIFICALLY DISCLAIMS AND EXCLUDES ALL OTHER SUCH WARRANTIES. NO WAIVER, ALTERATION, ADDITION OR MODIFICATION OF THE FOREGOING CONDITIONS SHALL BE VALID UNLESS MADE IN WRITING AND SIGNED BY AN EXECUTIVE OFFICER OF AVERY DENNISON. No salesman, representative, or agent of AVERY DENNISON is authorized to give any guarantee, warranty or make any representation contrary to the above. 5/5