Area of Exposure Type of Exposure First Aid Measures

Transcription

1 SECTION 1: IDENTIFICATION PRODUCT IDENTIFIER: Bossweld Manganese Bronze F/C Rods PRODUCT CODES: H, , H, SYNONYMS: Low fuming Manganese Bronze Flux Coated MANUFACTURER: Dynaweld Industrial Supplies Pty Ltd ADDRESS: 5 Sheridan Close Milperra NSW 2214 EMERGENCY PHONE: FAX PHONE: RECOMMENDED USE OF THE CHEMICAL AND RESTRICTIONS ON USE: Flux coated manganese bronze welding rod for oxy-acetylene gas flame braze welding of steel, cast iron, malleable iron. Extensively used in the automotive and maintenance industry. SECTION 2: HAZARD(S) IDENTIFICATION The product is harmless as it is, Dangers when used: A. UV and infrared radiation, heat and noise generated by the electric arc B. Fumes/Welding gases C. Electric shocks (welding systems) SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS Brazing and welding rods SECTION 4: FIRST AID MEASURES Area of Exposure Type of Exposure First Aid Measures Eyes arc glow and/or fumes Dampen with fresh water and seek medical attention Skin Considered to be non-irritant however it is possible that some Stop exposure and seek medical attention individuals may react to substances regarded as inert. Respiratory tract fumes inhalation Bring the injured person to a ventilated place and seek medical attention NOTES TO PHYSICIANS OR FIRST AID PROVIDERS: Treat symptomatically SECTION 5: FIRE-FIGHTING MEASURES

2 This product is not flammable. However the welding arc and sparks can ignite combustibles, therefore such materials should be kept away from areas where welding is taking place. In a fire toxic fumes of copper and zinc oxide may be evolved SECTION 6: ACCIDENTAL RELEASE MEASURES ACCIDENTAL RELEASE MEASURES: Crushing of the product should be avoided. PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES: None ENVIRONMENTAL PRECAUTIONS: None METHODS AND MATERIALS FOR CONTAINMENT AND CLEANING UP: None SECTION 7: HANDLING AND STORAGE Storage and Transport: Store in a cool, dry, well-ventilated area. Store away from acids and acetylene. No restrictions on transport. SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION Fumes and welding gases are developed when using the product; operate in a sufficiently ventilated place and/or install fumes extractors on the welding area.

3 Chemical Name CAS-No. TLV Mg/M3 Alloy Copper % Zinc Balance Tin % Flux: Boric Acid High Sodium Metaborate Medium ENGINEERING CONTROLS: INDIVIDUAL PROTECTION MEASURES Exposure Area Respiratory Eye Skin Ear Hand Thermal Protection Measure Avoid inhaling fumes/gases; be sure there is enough ventilation and/or fumes extractors are available. Use helmets with suitable shielding glass, protective screens or flash goggles Cover exposed areas with appropriate clothing Use ear protectors and/or ear plugs Use protective gloves Wear heat protective clothing SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES APPEARANCE: ODOR: ODOR THRESHOLD: ph: MELTING POINT/FREEZING POINT: INITIAL BOILING POINT AND BOILING RANGE: FLASH POINT: EVAPORATION RATE: FLAMMABILITY (solid, gas): None flammable UPPER/LOWER FLAMMABILITY OR EXPLOSIVE LIMITS: VAPOUR PRESSURE: VAPOUR DENSITY: RELATIVE DENSITY: SOLUBILITY: PARTITION COEFFICNET: N-OCTONOL/WATER: AUTO-IGNITION TEMPERATURE: DECOMPOSITION TEMPERATURE: VISCOSITY:

4 SECTION 10: STABILITY AND REACTIVITY REACTIVITY: CHEMICAL STABILITY: POSSIBILITY OF HAZARDOUS REACTIONS: CONDITIONS TO AVOID: INCOMPATIBLE MATERIALS: HAZARDOUS DECOMPISITION PRODUCTS: SECTION 11: TOXICOLOGICAL INFORMATION TOXICOLOGICAL INFORMATION: The product is not toxic as it is; when in use, refer to Sections 2 and 8. Prolonged operation causes chronic effects to eyes, ears and respiratory tract, SECTION 12: ECOLOGICAL INFORMATION ECOLOGICAL INFORMATION: Ferrous product; do not dispose of it in the environment (metal scrap). When used in combination with fumes extractors, treat the ensuing powders according to the provisions in force. SECTION 13: DISPOSAL CONSIDERATIONS Prevent waste from contaminating surrounding environment. Discard any products, residue, disposal container or liner in an environmentally acceptable manner in full compliance with federal, state and local regulations. SECTION 14: TRANSPORT INFORMATION High-density product, not dangerous according to the transport provisions in force. UN NUMBER: PROPER SHIPPING NAME: Boss MIG wire TRANSPORT HAZARD CLASS: None PACKING GROUP: ENVIRONMENTAL HARZARDS FOR TRANSPORT PURPOSES: SPEICAL PRECAUTIONS FOR USER: ADDITIONAL INFORMAITION: HAZCHEM OR EMERGENCY ACTION CODE: SECTION 15: REGULATORY INFORMATION MONTREAL PROTOCOL (OZONE DEPLETING SUBSTANCES): THE STOCKHOLM CONVENTION (PERSISTENT ORGANIC POLLUTANTS): THE ROTTERDAM CONVENTION (PRIOR INFORMED CONSENT):

5 Product Name Bossweld Manganese Bronze F/C Rods BASEL CONVENTION (HAZARDOUS WASTE): INTERNATIONAL CONVENTION FOR THE PREVENTION OF POLLUTION FROM SHIPS (MARPOL): SAFETY, HEALTH AND ENVIRONMENTAL REGUALTIONS: SECTION 16: OTHER INFORMATION OTHER INFORMATION: Dynaweld Industrial Supplies Pty Ltd requires that all customers read this product card carefully so as to be informed about the risks implied in the use of the product, and provide any person involved with a copy of the same and/or adequate training on the use of the product. This card has been drawn up in consideration of the directions contained in the information cards on welding fumes, published by the International Institute of Welding (IIW) and available in the Italian language at the Italian Institute of Welding, Genos.