General Specifications

Transcription

1 General Specifications Electrical Capacity (Resistive Load) Power Level V C 0V C Logic Level (gold): 0.4V 8V C/DC maximum (pplicable Range 0.m ~ 0mV ~ 8V) Logic/Power Level: Combines silver & gold ratings (gold over silver) Note: Find additional explanation of dual rating & operating range in Supplement section. Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Contact Timing: Total Travel: Materials & Finishes ctuator: Frame: Dust Cover: Case: Movable Contacts: Stationary Contacts: Terminals: Environmental Data Operating Temp Range: umidity: Vibration: Processing Shock: Soldering: Cleaning: 0 milliohms maximum for silver; 0 milliohms maximum for gold,000 megohms 00V DC,000V C minimum between contacts for minute minimum;,00v C minimum between contacts & case for minute minimum 00,000 operations minimum,000 operations minimum for silver; 0,000 operations minimum for gold Nonshorting (break-before-make) On-None-On circuit.087 (.mm); all other circuits.8 (.mm) Glass fiber reinforced PBT resin (UL94V-0) Stainless steel for panel & PCB mount; phosphor bronze with tin plating for bracket mount Phosphor bronze with nickel plating Glass fiber reinforced diallyl phthalate resin (UL94V-0) Silver alloy (code W); copper with gold plating (code G); or silver alloy with gold plating (code ) Silver capped copper with silver plating (code W); copper with gold plating (code G); or silver alloy with gold plating (code ) Copper or brass with silver or gold plating 0 C through +8 C ( F through +8 F) 90 ~ 9% humidity for 9 40 C (04 F) 0 ~ z with peak-to-peak amplitude of.mm traversing the frequency range & returning in minute; right angled directions for hours 0G (490m/s ) acceleration (tested in right angled directions, with shocks in each direction) Wave Soldering recommended (PC Mount). See Profile in Supplement section. Manual Soldering: See Profile in Supplement section. These devices are not process sealed. and clean locally using alcohol based solution. Standards & Certifications Flammability Standards: UL94V-0 rated actuator & case UL: File No. E444 - Recognized only when ordered with marking on switch. dd /U or /CUL to end of part number to order UL recognized switch. ll Single & Double Throw models recognized V C 0V C. CS: File No. 0_0_000 - Certified only when ordered with marking on switch. dd /C to end of part number to order CS certified switch. ll Double Throw & Throw models certified V 0V C, & 0.4V 8V DC. 0

2 Distinctive Characteristics vailable in flat frame and bracketed PC mounting types. Over-center actuator block and plunger design gives crisp actuation with clear indication of circuit status; this design also diminishes sparking and increases operating life. Guide interlocked with actuator block prevents window locking and maintains correct plunger alignment to assure contact stability. ntijamming design protects contacts from damage due to excessive downward force on the actuator. igh internal barriers between poles and insulating sheet between case and actuator block give added protection to contacts. Specially composed silver alloy contacts for power applications or gold contacts for logic level applications give high contact reliability. Prominent external insulating barriers increase insulation resistance and dielectric strength. Epoxy sealed terminals prevent entry of flux, solvents, and other contaminants. Clinching of frame to case well above base and terminals provides,00v dielectric strength. Series MS ctual Size

3 B MS Poles SPDT DPDT SPT Circuits NE OFF 0 ctuators (.8mm) Wide for Single or. (8.mm) Wide for (.8mm) Wide ctuator SPDT -NE- Circuit TYPICL SWITC ORDERING EXMPLE W G F N S Mounting Panel Mount (Terminal 0 only) PCB Mount (Terminal 0 only) Bracket Mount (Terminals, 0, & 40 only) Contact Materials & Ratings Silver; V C 0V C Gold; Rated 0.4V 8V C/DC max. Gold over Silver; V C & 0.4V 8V C/DC max. DESCRIPTI FOR TYPICL ORDERING EXMPLE MSSG0 S G Gold Contacts with 0.4V Rating Right ngle PC Terminals with Support Bracket 0 Terminals 0 Solder Lug * 0 Straight PC Straight with Bracket 0 Right ngle PC 40 Vertical PC * Wire harness & cable assemblies offered only in mericas IMPORTNT: Switches are supplied without UL, culus & CS marking unless specified. UL, culus & CS recognized only when ordered with marking on the switch. Specific models, ratings, & ordering instructions are noted on General Specifications page.

4 Series MS Pole SP DP Model MS MS MS MS Slide Position Connected Terminals Throw & Schematics Left Center Right Left Center Right NE OFF NE OFF Note: - OPEN - SPDT - -4 OPEN - - DPDT For Throw (-On) Connected Terminals & Schematics Terminal numbers are not actually on the switch. Pole Model Left Center Right Connection SP W G MS0 (.8mm) Wide for CTUTORS The SPT model utilizes a double pole base. connections must be made during field installation. Silver over Silver Power V C 0V C Gold over Brass or Copper Logic Level 0.4V 8V C/DC maximum Note: Complete explanation of operating range in Supplement section. Gold over Silver Connection (in) (out) 4 (out) (out) Connection (in) (out) 4 (out) (out) POLES & CIRCUITS (.8mm) Wide for CTCT MTERILS & RTINGS Power Level or Logic Level Connection (in) (out) 4 (out) (out) Note: This dual rated option is suitable when two or more identical switches are used in logic and in power circuits within the same application. See Supplement section for complete explanation of dual rating and operating range. B (COM) 4 (COM) (out) Conn Common (in) 4 (out) (out). (8.mm) Wide for Only V C or 0.4V 8V C/DC maximum

5 F S 0 Panel Mount (Combines with Solder Lug Terminal 0 only) Dimension =.8 (.8mm) for on-none-on.9 (8.mm) for on-off-on & on-on-on Maximum Panel Thickness:.97 (.0mm) Support Bracket Mount (For Terminals, 0, & 40) Maximum Panel Thickness: For Straight PC with Bracket Terminal :.97 (.0mm) For ngle Mount Terminals 0 & 40:.77 (4.mm) Solder Lug Epoxy Seal (.0) Solder Lug Terminals MSFW0 Solder Lug Terminals MSBFW0 (.).04 Thk = (0.8).0 (4.0).7 (.0) (7.).90 (9.).77 (.) R Typ (7.).90 (9.).77 (.) R Typ (.).40 MOUNTING TYPES & TERMINLS 0 Straight PC (.4) Dia Typ.094 (4.9). (7.).90 SP or DP with (.8mm) ctuator Epoxy Seal (.).0 TYPICL SWITC DIMENSIS (.).40 (.).0 (.) R Typ (7.).90 (9.).77 (.7).04 Thk = (0.8).0 Sq (.).40 (8.)..0 (9.0).4 (.4) Dia Typ.094 (7.).90 DP only with. (8.mm) ctuator.0 (.4). (4.).77 (.) x (.0) Typ.04 x (7.) (4.).77 N Straight PC Mount (Combines with Straight PC Terminal 0 only) Straight PC with Bracket Right ngle PC Vertical PC (.) x (.0) Typ.04 x.0.00 (.7).00 (.0) 4 (.4) (.0) Typ (.7).00 4

6 Series MS.409 (.).0 (.).0 (8.). (8.)..409 Sq TYPICL SWITC DIMENSIS (.4). (7.).99 (.).0 (.).0 (.7).4 (.). (.7).4 (4.) (0.).04.0 (.8)..0 (0.).04 (.8). (.7).00 (.7).04 4 (.4) (.7) Typ.04 (.7).00 (.). (.) Typ (.7) Typ.04 (.). (7.).80 4 (.9).49 (.7).00 (.7).04 (.) Typ (.7).00 Straight PC Terminals MSNG0 Straight PC Terminals MSBNG0 Straight PC Terminals with Bracket (.8) Dia Typ.07 4 C L 4 (.8) Dia Typ.07 (.) Typ.0 (7.9) Typ. (.8) Dia Typ.07 (.) Dia Typ Straight PC Terminals with Bracket (.) Typ.0 (.4) Typ.09 (7.9) Typ. (.8) Dia Typ.07 (.) Dia Typ MSSG MSBSG

7 Right ngle PC Terminals MSSG0 Right ngle PC Terminals MSBSG0 Vertical PC Terminals MSSG40 Vertical PC Terminals MSBSG40.0 (.) Typ (4.4).7.0 (.).0 (.) Typ (4.4).7 (.).0.0 TYPICL SWITC DIMENSIS (.) Typ (4.4).7 (.).0 (8.). Sq.0 (.7).4 (.) (9.).7 (8.). Sq.0 (.7).4 (.8) (.7).00 (.) (.7) (.)..00 (.).4 (.7) Typ.00 (.8).0 (.).09.0 (.).09.0 (0.) (.7) (.9).70.0 (.8) Typ (.9).70.0 (.8) Typ (.)..00 (.7).0 (.7).0 (.7) (.).0.0 (.).0 (.4) (.7) (.7) (.7) 4 (.7) 4 (.4).0.00 (.7) Typ.00 (.8) Dia Typ.07 (9.).7 (.) Typ.0 (.) Dia Typ (.8) Dia Typ.07 4 (.8) (.) Dia Typ (0.).400 (.7) (.) Typ.0 (.8) Dia Typ.07 (.8) Typ (4.4) Typ.7 (.) Dia Typ (.8) Dia Typ.07 (.8) Typ 4 (.7) (4.4) Typ.7 (.) Dia Typ