Replaces Ryan GA30-06 Parts

Transcription

1 Replaces Ryan GA30-06 Parts Item R&R O.E.M. Req. No. Part No. Part No. Description Qty. 1 R R&R Ball Bearing, Connecting Rod 8 1 R R&R Ball Bearing, Crankshaft 4 1 R R&R Ball Bearing, Crank Support 4 1 R R&R Bearing, Connecting Rod 8 2 R R&R Pivot Pin, Old Style Model 9110 & R R&R Pivot Pin, New Style Model & Up 8 3 R R&R Belt, Drive 1 4 R R&R Chain, Drive 3 R R&R Brake Shoe 4 6 R R&R Tine Holder, 1" Mounting Dia. 4 7 R R&R Element, Air Filter 1 8 R Use R R R&R Fuel Filter 1 9 R R&R Connecting Link

2 Replaces Ryan GA30 Parts Alloy Solid Tines These tines aerate without the work of cleaning up the mess of cores and debris left behind with conventional core aerating. R&R Solid Tines are manufactured from a special high-carbon steel bar and heat treated to RC4-48 in our own heat treat facility. They are available in all standard sizes but are especially popular in the smaller diameters for aerating in the summer months to relieve the stress on greens by allowing water, air and nutrients to easily flow into the root zone. With the combination of small holes and no cores, play can be resumed immediately. R Needle, Alloy R Needle, Alloy R Solid, Alloy R23863 Solid, Alloy R Solid, Alloy R Solid, Alloy R Solid, Alloy R Solid, Alloy R Solid, Alloy R20141 Solid, Alloy R Solid, Alloy R Solid, Alloy R Solid, Alloy R Solid, Alloy R Solid, Alloy Alloy Shatter Tines With their + shape, R&R shatter tines relieve compaction and allow water, air and nutrients to flow in the root zones and beyond with virtually no visible surface disturbance. Because of their unique shape the aerating area is maximized while allowing play to be resumed immediately. R&R Shatter Tines are manufactured from special high-carbon alloy investment castings and heat treated to RC4-48 in our own facility to insure you of optimum quality R20146 Shatter, Alloy cross - - R201 Shatter, Alloy cross - - R20147 Shatter, Alloy cross - - R20160 Shatter, Alloy cross - - R Shatter, Alloy cross - - R20149 Shatter, Alloy cross - - R20170 Shatter, Alloy cross - - R Shatter, Alloy cross - - R Shatter, Alloy cross - - All original equipment manufacturers names and part numbers are used for identification purposes only, and we are in no way implying that our products are original equipment parts. Prices subject to change without notice.

3 Replaces Ryan GA30 Parts Standard Hollow Tines Designed to remove a soil core, R&R Standard Hollow Tines are constructed from case hardened tubular steel and are the most economical tines available. Case hardening hardens the inner and outer surfaces of the tine wall to over RC for added wear. R2327 Hollow, Standard R23274 Hollow, Standard R Hollow, Standard R23472 Hollow, Standard R Hollow, Standard R Hollow, Standard Alloy Hollow Tines Like Standard Hollow Tines, this line is also tubular and designed to remove a soil core, but they are constructed from a special high carbon alloy steel. The steel tubing is specially manufactured for R&R to achieve uniform hardness of RC4-48 throughout the tine for excellent wear and toughness. These tines are much tougher and resist bending in extremely hard or rocky soils and you can expect 3-4 times longer life than from the Standard Hollow Tines. R20186 Hollow, Alloy R20188 Hollow, Alloy R20187 Hollow, Alloy R20189 Hollow, Alloy Carbide-Tipped Alloy Hollow Tines The R&R Carbide-Tipped Alloy Hollow Tine construction is the same special high carbon alloy steel tubing and hardened to RC4-48 as the alloy hollow tines, with the addition of a carbide tip for even longer life. The advantage of using carbide tipped tines is the ability to maintain your maximum aerating depth consistently over the life of the tines. You can expect these tines to last 6-8 times longer than the R&R Standard Hollow Tines. Carbide tipped tines are not recommended in rocky soil conditions, as carbide, which is extremely wear resistant, can break when encountering hard impacts in rocks. R20144 Hollow, Carbide Tipped.70".00".42".270".072" R Hollow, Carbide Tipped R Hollow, Carbide Tipped.70".00".2" " R Hollow, Carbide Tipped.70".00".630".480".072" R Hollow, Carbide Tipped Alloy Slicing Knife Tines These tines allow water, air and nutrients to flow into the root zones and beyond with virtually no visible surface disturbance, allowing play to be resumed immediately. All of these tines are precision machined out of solid high-carbon alloy steel bar and heat treated in our own facility to RC4-48 and carry the same lifetime guarantee of quality as all our other tines R20147 Slicing Knife, Alloy x.160

4 Replaces Ryan GA30 Parts Hollow Alloy Side-Eject Tines Manufactured from special high carbon alloy tubular steel with a precision machined slot in the side wall to allow for more efficient core removal in heavy soils. R&R s unique method of machining maintains the maximum side wall height for strength to avoid bending. These tines are through hardened to RC4-48 to create a much tougher and more wear resistant tine. R20193 Side Eject, Hollow Alloy R20194 Side Eject, Hollow Alloy Machined Alloy Side-Eject Tines These alloy tines remove a soil core which quickly exits the side of the tine through a precision machined slot. This slot is designed to avoid plugging that can occur using hollow tubular tines (especially the smaller diameters) in heavy soil conditions. R&R manufactures a wide selection of these side-eject tines machined from special high-carbon alloy steel solid bar and heat treated to RC4-48 in our own heat treating facility. These side eject tines are very popular for the multiple tine holders which fit all greens aerators. R Side Eject, Machined Alloy R20163 Side Eject, Machined Alloy R23864 Side Eject, Machined Alloy R20119 Side Eject, Machined Alloy R Side Eject, Machined Alloy R Side Eject, Machined Alloy R20120 Side Eject, Machined Alloy R Side Eject, Machined Alloy R20121 Side Eject, Machined Alloy R2013 Side Eject, Machined Alloy R20136 Side Eject, Machined Alloy R20137 Side Eject, Machined Alloy Alloy Spoons All R&R Alloy Spoons are stamped and formed from special high strength alloy sheet steel and heat treated in our own facility to RC4-48. These spoons are all side eject by design for dependable plug ejection and extremely strong for heavy duty applications such as fairways, collars and tees. They are also a great value for your money. R Closed Spoon, Open Side,Alloy R Closed Spoon, Open Side,Alloy All original equipment manufacturers names and part numbers are used for identification purposes only, and we are in no way implying that our products are original equipment parts. Prices subject to change without notice.

5 Replaces Ryan GA30 Parts Carbide-Tipped Machined Alloy Side Eject Tines These alloy tines remove a soil core which quickly exits the side of the tine through a precision machined slot. This slot is designed to avoid plugging that can occur using hollow tubular tines (especially the smaller diameters) in heavy soil conditions. R&R manufactures a wide selection of these side-eject tines machined from special high-carbon alloy steel solid bar and heat treated to RC4-48 in our own heat treating facility. A carbide tip is then added for even longer life. The advantage of using carbide tipped tines is the ability to maintain your maximum aerating depth consistently over the life of the tines. R20167 New! R New! R New! R New! R New! R New! R20169 New! R New!.00" 3.00".400".300".049".00" 3.00".4".400".062".00" 3.00".64".00".062".00" 4.00".400".300".049".00" 4.00".4".400".062".00" 4.00".64".00".062".70" 3.00".64".00".062".70" 4.00".64".00".062" Carbide-Tipped Hollow Alloy Side-Eject Tines Manufactured from special high carbon alloy tubular steel with a precision machined slot in the side wall to allow for more efficient core removal in heavy soils. R&R s unique method of machining maintains the maximum side wall height for strength to avoid bending. These tines are through hardened to RC4-48 to create a much tougher and more wear resistant tine. A carbide tip is then added for even longer life. The advantage of using carbide tipped tines is the ability to maintain your maximum aerating depth consistently over the life of the tines. R R R20140 Side Eject, Hollow Alloy - Carbide Tipped.70".00".42".27".072" Side Eject, Hollow Alloy - Carbide Tipped.70".00".2".30".072" Side Eject, Hollow Alloy - Carbide Tipped.70".00".630".480".072" 1091

6 Replaces Ryan GA30 Parts Tine Holders & Traction Unit Cylinder Repair Kit All original equipment manufacturers names and part numbers are used for identification purposes only, and we are in no way implying that our products are original equipment parts. Prices subject to change without notice.

7 Replaces Ryan GA30 Parts Tine Holders & Traction Unit Item R&R O.E.M. Req. No. Part No. Part No. Description Qty. 1 R R&R 3 Tine Holder, 3/4" Tine Mounting Dia., Incl. #8 4 1 R R&R 3 Tine Holder, /8" Tine Mounting Dia., Incl. #8 4 1 R R&R 3 Tine Holder, 7/8" Tine Mounting Dia., Incl. #8 4 2 R R&R Tine Holder, 1/2" Tine Mounting Dia., Incl. #8 4 3 R R&R Only R&R Tine Holder,Fits Needle Tines Only 4 4 R47601S R&R Stud, Tine Holder, 1/ R47600S R&R Stud, Tine Holder, 7/ R R&R Lock Washer, /16" A/R 6 R R&R Bolt, /16-18 x 1-1/4" A/R 7 R R&R Bolt, /16-18 x 1" A/R 8 R R&R Flanged Locknut, 1/2-20 A/R 9 R R&R 4 Finger Turf Hold Down 1 use with 3 Tine Holder 10 R R&R 3 Finger Turf Hold Down 3 use with 3 Tine Holder 11 R R&R 6 Finger Turf Hold Down 1 use with Tine Holder 12 R R&R Finger Turf Hold Down 3 use with Tine Holder 13 R R&R Drive Belt, 2V 1 14 R Use R R R&R Fuel Filter 1 1 R R&R Hyd. Oil Filter 1 16 R R&R Bearing A/R 16 RA R&R Bearing A/R 16 R R&R Bearing A/R 17 R R&R Tire, x 12, 4 Ply Dico Turf Trac 2 18 R R&R Seal Kit, Cylinder 1 19 R R&R Brake Lining, (Set of 2 with Rivits) 2 20 R R&R Rivet, Brake Lining 6 21 R R&R Choke Control 1 21 R Use R R R&R Chain 2 23 R R&R Pivot Pin 4 24 R R&R Starter Solenoid

8 Replaces Ryan Greensaire II & WG-24 Parts Alloy Solid Tines These tines aerate without the work of cleaning up the mess of cores and debris left behind with conventional core aerating. R&R Solid Tines are manufactured from a special high-carbon steel bar and heat treated to RC4-48 in our own heat treat facility. They are available in all standard sizes but are especially popular in the smaller diameters for aerating in the summer months to relieve the stress on greens by allowing water, air and nutrients to easily flow into the root zone. With the combination of small holes and no cores, play can be resumed immediately. R Solid, Needle Alloy R Solid, Needle Alloy R Solid, Overseeding Alloy R23863 Solid, Alloy R Solid, Alloy R Solid, Alloy R Solid, Alloy R Solid, Alloy R20134 Solid, Alloy R Solid, Alloy R Solid, Alloy R Solid, Alloy R Solid, Alloy Alloy Shatter Tines With their + shape, R&R shatter tines relieve compaction and allow water, air and nutrients to flow in the root zones and beyond with virtually no visible surface disturbance. Because of their unique shape the aerating area is maximized while allowing play to be resumed immediately. R&R Shatter Tines are manufactured from special high-carbon alloy investment castings and heat treated to RC4-48 in our own facility to insure you of optimum quality. R20146 Shatter, Alloy cross - - R201 Shatter, Alloy cross - - R20147 Shatter, Alloy cross - - R20160 Shatter, Alloy cross - - R20149 Shatter, Alloy cross - - R20170 Shatter, Alloy cross - - R Shatter, Alloy cross All original equipment manufacturers names and part numbers are used for identification purposes only, and we are in no way implying that our products are original equipment parts. Prices subject to change without notice.

9 Replaces Ryan Greensaire II & WG-24 Parts Standard Hollow Tines Designed to remove a soil core, R&R Standard Hollow Tines are constructed from case hardened tubular steel and are the most economical tines available. Case hardening hardens the inner and outer surfaces of the tine wall to over RC for added wear. R20133 Hollow, Standard R Hollow, Standard R Hollow, Standard R Hollow, Standard Alloy Hollow Tines Like Standard Hollow Tines, this line is also tubular and designed to remove a soil core, but they are constructed from a special high carbon alloy steel. The steel tubing is specially manufactured for R&R to achieve uniform hardness of RC4-48 throughout the tine for excellent wear and toughness. These tines are much tougher and resist bending in extremely hard or rocky soils and you can expect 3-4 times longer life than from the Standard Hollow Tines. R20181 Hollow, Alloy R20183 Hollow, Alloy R20182 Hollow, Alloy R20184 Hollow, Alloy Carbide-Tipped Alloy Hollow Tines The R&R Carbide-Tipped Alloy Hollow Tine construction is the same special high carbon alloy steel tubing and hardened to RC4-48 as the alloy hollow tines, with the addition of a carbide tip for even longer life. The advantage of using carbide tipped tines is the ability to maintain your maximum aerating depth consistently over the life of the tines. You can expect these tines to last 6-8 times longer than the R&R Standard Hollow Tines. Carbide tipped tines are not recommended in rocky soil conditions, as carbide, which is extremely wear resistant, can break when encountering hard impacts in rocks. R Hollow, Carbide Tipped R Hollow, Carbide Tipped R20108 Hollow, Carbide Tipped.70" 4.70".42".27".072" R20110 Hollow, Carbide Tipped.70" 4.70".2".30".072" R20112 Hollow, Carbide Tipped.70" 4.70".630".480".072" 109

10 Replaces Ryan Greensaire II & WG-24 Parts Machined Alloy Side-Eject Tines These alloy tines remove a soil core which quickly exits the side of the tine through a precision machined slot. This slot is designed to avoid plugging that can occur using hollow tubular tines (especially the smaller diameters) in heavy soil conditions. R&R manufactures a wide selection of these side-eject tines machined from special high-carbon alloy steel solid bar and heat treated to RC4-48 in our own heat treating facility. These side eject tines are very popular for the multiple tine holders which fit all greens aerators. R Side Eject, Machined Alloy R20163 Side Eject, Machined Alloy R23864 Side Eject, Machined Alloy R20119 Side Eject, Machined Alloy R Side Eject, Machined Alloy R20120 Side Eject, Machined Alloy R Side Eject, Machined Alloy R20121 Side Eject, Machined Alloy R20123 Side Eject, Machined Alloy R20124 Side Eject, Machined Alloy R2012 Side Eject, Machined Alloy Hollow Alloy Side-Eject Tines Manufactured from special high carbon alloy tubular steel with a precision machined slot in the side wall to allow for more efficient core removal in heavy soils. R&R s unique method of machining maintains the maximum side wall height for strength to avoid bending. These tines are through hardened to RC4-48 to create a much tougher and more wear resistant tine. R2019 Side Eject, Hollow Alloy R20196 Side Eject, Hollow Alloy Alloy Slicing Knife Tines These tines allow water, air and nutrients to flow into the root zones and beyond with virtually no visible surface disturbance, allowing play to be resumed immediately. All of these tines are precision machined out of solid high-carbon alloy steel bar and heat treated in our own facility to RC4-48 and carry the same lifetime guarantee of quality as all our other tines. R20144 Slicing Knife, Alloy x R2014 Slicing Knife, Alloy x All original equipment manufacturers names and part numbers are used for identification purposes only, and we are in no way implying that our products are original equipment parts. Prices subject to change without notice.

11 Replaces Ryan Greensaire II & WG-24 Parts Carbide-Tipped Machined Alloy Side Eject Tines These alloy tines remove a soil core which quickly exits the side of the tine through a precision machined slot. This slot is designed to avoid plugging that can occur using hollow tubular tines (especially the smaller diameters) in heavy soil conditions. R&R manufactures a wide selection of these side-eject tines machined from special high-carbon alloy steel solid bar and heat treated to RC4-48 in our own heat treating facility. A carbide tip is then added for even longer life. The advantage of using carbide tipped tines is the ability to maintain your maximum aerating depth consistently over the life of the tines. R20167 R R R R R R20168 R R R R20169 R " 3.00".400".300".049".00" 3.00".4".400".062".00" 3.00".64".00".062".00" 4.00".400".300".049".00" 4.00".4".400".062".00" 4.00".64".00".062".62" 3.00".4".400".062".62" 3.00".64".00".062".62" 4.00".4".400".062".62" 4.00".64".00".062".70" 3.00".64".00".062".70" 4.00".64".00".062" Carbide-Tipped Hollow Alloy Side-Eject Tines Manufactured from special high carbon alloy tubular steel with a precision machined slot in the side wall to allow for more efficient core removal in heavy soils. R&R s unique method of machining maintains the maximum side wall height for strength to avoid bending. These tines are through hardened to RC4-48 to create a much tougher and more wear resistant tine. A carbide tip is then added for even longer life. The advantage of using carbide tipped tines is the ability to maintain your maximum aerating depth consistently over the life of the tines. R20109 Side Eject, Hollow Alloy - Carbide Tipped.70" 4.70".42".27".072" R20111 Side Eject, Hollow Alloy - Carbide Tipped.70" 4.70".2".30".072" R20113 Side Eject, Hollow Alloy - Carbide Tipped.70" 4.70".630".480".072" 1097

12 Replaces Ryan Greensaire II & WG-24 Parts Tine Holders See Next Page A Genuine Briggs & Stratton engines and parts available REPLACES RYAN "NEW STYLE" SLIDE AND GUIDE ASSEMBLY PARTS LUBRICATION FREE R&R Products reengineered R slide assemblies (Replaces Ryan Part #4978) are manufactured with special triple layered composite bushings. The use of these bushings eliminates the need for lubrication and insures against oil leakage on turf surfaces. R&R also uses triple lipped seals and induction hardened hard chrome plated shafts for added life REPLACES RYAN 24 TINE HOLDER ASSEMBLY PARTS 30A 24 TINE HOLDER ASSEMBLY R R&R 24 Tine Holder Assembly Kit Includes: 6 Tine Holders, 6 Washers, 2 Brackets, 1 Mounting Plate, & 1 Turf Hold-down Individual Parts also available in listing All original equipment manufacturers names and part numbers are used for identification purposes only, and we are in no way implying that our products are original equipment parts. Prices subject to change without notice.

13 Replaces Ryan Greensaire II & WG-24 Parts Tine Holders Item R&R GA II WG24 Req. No. Part No. Part No. Part No. Description Qty. 1 R R&R Fitting, Grease 12 2 R B42 R&R Bolt, 3/8-16 x 1-1/4" 12 2 R Use R R LW4 R&R Lock Washer, 3/8" 12 4 R48308 Use R R4306 SBG1 R&R Insert, Two Halves 4 4 R R&R Insert, Two Halves 6 R B147 R&R Bolt, 1/4-20 x 1" 12 6 R LW7 R&R Lock Washer 12 7 R B9 R&R Bolt, 1/4-20 x 3/4" 6 8 R LW7 R&R Lock Washer 6 9 R A Use R R A R&R Pin, Dowel 6 10 R R&R Retainer Assembly with Bearing R44446 BG43 R&R Bearing Retainer Assembly 6 includes 2 Part #R47293 &1 Part #R R R&R Bearing, Needle R A R&R Rod Assembly 6 13 R Use R R A3 R&R Pin, Slide Assy. 6 1 R BG38 R&R Bearing 6 16 R Use R R R&R Retainer, Spring 17 R SP4 R&R Spring 6 18 R B11 R&R Bolt, 3/8-16 x 1" Nyloc R R&R Bushing, Guide Assembly R R&R Guide Assembly, includes: 6 21 R OS9 R&R Oil Seal R A Use R R R&R Push Rod, Induction Hardened 6 23 R4822 Thin OS7 R&R Oil Seal Serial #7173 & under R48277 OS32 Use R R OS32 R&R Oil Seal R A3 R&R Slide Assembly; with 2 each R2026 bushings, R48229 grease fittings & R48274 oil seals 6 2 R R&R Bolt, Nyloc 1/4-20 x 1/2" 6 26 R R&R Bolt, 1/4-20 x 1-1/4" R R&R Lock Washer, 1/4" R B27 R&R Bolt, /16-18 x 1-1/4" 6 29 R LW4 R&R Lock Washer, /16" 6 30 R A R&R 2 Tine Holder 6 30 R A R&R 2 Tine Holder 6 30A R R&R 4 Tine Holder,.00 Tine Mounting Dia. 6 30B R R&R Only R&R 4 Tine Holder, Fits Needle Tines Only 6 30B R R&R Only R&R 4 Tine Holder, /8" Mounting Dia R48128 BG49 R&R Bearing 2 31 R R&R Bearing 3 32 R R&R Race, Inner 1 33 R R&R Race, Inner 2 3 R A1 R&R Bushing, Slide Assembly 12 3 R R&R Bushing, Slide Assembly 1 O.D

14 Replaces Ryan Greensaire II & WG-24 Parts Tine Holders 1100 Item R&R GA II WG24 Req. No. Part No. Part No. Part No. Description Qty. 36 R48878 R&R Tire, x 6, 2 Ply Rib 2 36 R WG-1 R&R Tire, x, 2 Ply Rib 2 37 R R&R Belt 1 38 R R&R Chain # R WG-2 R&R Chain # R A R&R Chain # R A R&R Chain #0 Crank 2 38 R R&R Chain # R R&R Chain # R Use R R R&R Chain # R R&R Chain # R R&R Chain #0, Crankshaft 2 38 R4000 R&R Offset Link #40 A/R 40 R R&R Deflector incl. R R R&R Throttle Control 1 42 R R&R Hex Head Bolt, Slide Assy R R&R Flanged Whiz Nut, Slide Assy R R&R Flat Washer 6 4 R R&R Guide Assy., Incl 2 ea. #46 & 1 ea. # R R&R Bushing, Guide Assy., 12 Triple Layered Composite 47 R R&R Bushing, Slide Assy., 12 Triple Layered Composite 48 R R&R Plug, Shaft End 6 49 R R&R Seal, Slide Assy., Triple Lip 12 0 R R&R Seal, Guide Assy., Triple Lip 12 1 R R&R Felt Plug, Slide Assy., 6 (not used on R&R Slide) 2 R R&R Felt Pad, Slide Assy., 12 (not used on R&R Slide) 3 R R&R Bolt, 3/8-16 x 1" Nyloc 24 4 R Use R R R&R Only R&R Lubrication Free Slide Assy. 6 Complete with Induction Hardened & Hard Chrome plated shaft, Incl. items #47-49 R R&R Turf Hold-down, 1 use only with 4 Tine Holders R R&R Only R&R Turf Hold-down, 1 use with 4 Tine Holder with.62 Tines 6 R R&R Mounting Plate, Turf Hold-down 1 7 R R&R Bracket 2 8 R R&R Bolt, Socket Head, /16-18 x 1" 1 9 R R&R Bolt, Hex Head, /16-18 x 2-1/2" 2 60 R R&R Lock Washer, All original equipment manufacturers names and part numbers are used for identification purposes only, and we are in no way implying that our products are original equipment parts. Prices subject to change without notice.

15 Replaces Ryan / Cushman GA60 Parts Alloy Solid Tines These tines aerate without the work of cleaning up the mess of cores and debris left behind with conventional core aerating. R&R Solid Tines are manufactured from a special high-carbon steel bar and heat treated to RC4-48 in our own heat treat facility. They are available in all standard sizes but are especially popular in the smaller diameters for aerating in the summer months to relieve the stress on greens by allowing water, air and nutrients to easily flow into the root zone. With the combination of small holes and no cores, play can be resumed immediately. R Solid, Alloy R Solid, Alloy R Solid, Alloy Alloy Shatter Tines With their + shape, R&R shatter tines relieve compaction and allow water, air and nutrients to flow in the root zones and beyond with virtually no visible surface disturbance. Because of their unique shape the aerating area is maximized while allowing play to be resumed immediately. R&R Shatter Tines are manufactured from special high-carbon alloy investment castings and heat treated to RC4-48 in our own facility to insure you of optimum quality. R Shatter, Alloy cross - - R Shatter, Alloy cross - - Alloy Slicing Knife Tines These tines allow water, air and nutrients to flow into the root zones and beyond with virtually no visible surface disturbance, allowing play to be resumed immediately. All of these tines are precision machined out of solid high-carbon alloy steel bar and heat treated in our own facility to RC4-48 and carry the same lifetime guarantee of quality as all our other tines. R20147 Slicing Knife, Alloy x Alloy Spoons All R&R Alloy Spoons are stamped and formed from special high strength alloy sheet steel and heat treated in our own facility to RC4-48. These spoons are all side eject by design for dependable plug ejection and extremely strong for heavy duty applications such as fairways, collars and tees. They are also a great value for your money R Closed Spoon, Side Eject,Alloy R Closed Spoon, Side Eject,Alloy

16 Replaces Ryan Renovaire-Tracaire Parts Item R&R O.E.M. Req. No. Part No. Part No. Description Qty. 1 R R&R 1/2" Closed Spoon 96 2 R R&R 1/2" Open Spoon 96 1 R R&R 3/4" Closed Spoon 96 2 R R&R 3/4" Open Spoon 96 Tech Note: All above spoons 7-1/2" long with /16 mounting hole 3 R R&R Renovating Tine 96 R R&R 4" Slicing Knife 96 4 R R&R 6" Slicing Knife 96 Tech Note: All above knives mounting holes 2-1/2" on center 6 R R&R Clamp, Spoon 96 7 R R&R Bolt R R&R Flanged Locknut 192 R R&R Tire 4.80 x 8, 4 Ply T.T. Ind. Stud Goodyear 2 R232-3 R&R 4.80 x 8 Tube 2 R R&R Bearing, Wheel 4 R R&R Cup, Wheel 4 R R&R Seal, Aerating Wheel 24 Replaces Ryan Lawnaire 28 Parts 1102 Item R&R O.E.M. Req. No. Part No. Part No. Description Qty. R Use R R R&R Only R&R Tine Assy., 3/4", Side Ejection 4 Heat Treated Aircraft Alloy Steel RA R&R Bearing, Link Arm R R&R Bearing, Crankshaft All original equipment manufacturers names and part numbers are used for identification purposes only, and we are in no way implying that our products are original equipment parts. Prices subject to change without notice.

17 Replaces Ryan Mataway, Ren-O-Thin & Spike-Aire Parts Item R&R O.E.M. Req. No. Part No. Part No. Description Qty. 1 R R&R Mataway Straight 1/32" 1 R201323C New! R&R Only R&R Mataway Straight 1/32", Carbide Tipped 1 R R&R Mataway Straight 1/8" 1 R201324C New! R&R Only R&R Mataway Straight 1/8", Carbide Tipped 1 R R&R Mataway Straight 1/16" 1 R20132C New! R&R Only R&R Mataway Straight 1/16", Carbide Tipped 1 R R&R Mataway Offset 1/16" Tech Note: 7-1/4" Long, 1" Hex mounting hole (all above mataways) 2 R R&R Ren-o-thin Flail 1/8 2 R201327C New! R&R Only R&R Ren-o-thin Flail 1/8, Carbide Tipped 3 R R&R Spiker Blade, 13 Point Tech Note: 10" diameter, 1" Hex mounting hole, 12ga (.104) thick) 4 R R&R Spiker Blade, 8 Point R R&R Drive Belts (Matched Set of 3), Fits Mataway Replaces Ryan Lawnaire IV Parts 1103 Item R&R O.E.M. Req. No. Part No. Part No. Description Qty. 1 R R&R 3/4" Closed Spoon, 14 GA.

18 Replaces Ryan Sod Cutter Parts Item R&R O.E.M. Req. No. Part No. Part No. Description Qty. 1 R2036 R&R Only R&R 12" Sod Cutter Blade, 1/4" x 2 1/2" 1 R2039 R&R Only R&R 1" Sod Cutter Blade, 1/4" x 2 1/2" 1 R2038 R&R Only R&R 16" Sod Cutter Blade, 1/4" x 2 1/2" 1 R2033 R&R Only R&R 18" Sod Cutter Blade, 1/4" x 2 1/2" R R&R Bearing, Fits VI R R&R Bearing, Fits Jr. & V2 R R&R Bearing, Fits Jr. V1 & V2 R R&R Belt, Fits Jr. Machine R R&R Belt, Single for Briggs Engine R R&R Belt, Matched for Briggs Engine R R&R Belt, Matched for Wis. Engine R R&R Belt, Matched 24" Machine 2 R2040 R&R /16" x 1" Gr. 8 Hardened Bolt w/lock Washer & Lock Nut, pkg of 2 2 R20406 R&R /16" x 1" Gr. 8 Hardened Bolt w/whiz Nut, pkg of 2 3 R R&R Cutter Blade Arm, Fits Jr. R R&R Seal, Side Arm R R&R Bearing, Needle R R&R Bearing Replaces Ryan Cutt-Off Parts R&R Part No. Description Striaght Edge Blades R20380 R&R Straight Cutt-Off Blade, Fits 12" Sod Cutter R20382 R&R Straight Cutt-Off Blade, Fits 1" Sod Cutter R20384 R&R Straight Cutt-Off Blade, Fits 16" Sod Cutter R2038 R&R Straight Cutt-Off Blade, Fits 18" Sod Cutter R20386 R&R Straight Cutt-Off Blade, Fits 24" Sod Cutter 1104 Serrated Edge Blades R R&R Serrated Cutt-Off Blade, Fits 12" Sod Cutter R R&R Serrated Cutt-Off Blade, Fits 1" Sod Cutter R R&R Serrated Cutt-Off Blade, Fits 16" Sod Cutter R20138 R&R Serrated Cutt-Off Blade, Fits 18" Sod Cutter R R&R Serrated Cutt-Off Blade, Fits 24" Sod Cutter All original equipment manufacturers names and part numbers are used for identification purposes only, and we are in no way implying that our products are original equipment parts. Prices subject to change without notice.