V a l v e s. Design Excellence

Transcription

1 V a l v e s 1 Design Excellence

2 LEGACY LV1 DELTA SERIES VALVE Provides all the standard design features which differentiate the compact from the typical ball valve that customers have come to expect: Firesafe tested under API FA Lower weight and shorter length with a smaller overall foot print Serviceremovable handle Large seattoball contact area Simple piece body for easy rebuild Robust L seal and seat carrier design SMALLER, SMARTER MANIFOLD DESIGN Legacy s compact valve design reduces the weight and size requirements of typical manifold systems. The illustration below compares the LV1 s footprint with that of a traditional ANSI trunnion ball valve with included companion flanges. Total weight is approximately % less Total length is approximately 0% less DISTINCTIVE STANDARD FEATURES OF THE LV1 Proprietary ConstaTorq seat material provides: Consistent lowtorque actuation over entire range of pressures and temperatures Service temperature range of 20F (0F to 00F), Chemical compatibility surpassed ONLY by Flouropolymers A more environmentally sustainable solution than Celcon, Nylon, or PEEK PTFE Coated Cr or Ni plated ball reduces friction and torque Stainless Steel Stop Plates eliminates corrosion of painted stop plates 2

3 1 2 2 LEGACY VALVE LV1 SERIES COMPONENT PARTS INDEX DESCRIPTION QTY STANDARD MATERIALS OPTIONAL MATERIALS 1 1 HANDLE 1 CARBON STEEL 2 STOP PLATE 1 1 SS N/A STEM BEARING 1 PTFE COATED ALLOY STEEL HANDLE + EXT GEAR OPERATOR BONNET BOLTS A19 B A20 L BONNET 1 CARBON STEEL ALLOY STEEL 1 PH SS 1 SS BONNET SEAL 1 PEROXIDECURED NITRILE STEM SEAL 1 POLYMYTE/PEROXIDECURED NITRILE POLYMYTE/VITON THRUST BEARING 1 ALUMINUM BRONZE 9 STEM 1 1 PH SS NICKEL ALLOY END CONNECTION SEAL 2 PEROXIDECURED NITRILE 11 BODY 1 CARBON STEEL ALLOY STEEL 12 GREASE FITTING 1 ALLOY STEEL 1 SS 1 LSEAL 2 PEROXIDECURED NITRILE 1 SEAT CARRIER 2 CARBON STEEL 1PH SS 1 SS 1 SEAT 2 CONSTATORQ CELCON PEEK 1 BALL 1 ENP CARBON STEEL 1PH SS 1 SS 1 RETAINER SEAL 1 PEROXIDECURED NITRILE 1 RETAINER 1 CARBON STEEL ALLOY STEEL 1PH SS 1 SS 19 SET SCREW 2 STAINLESS STEEL 20 HALF RING ALLOY STEEL 21 NIPPLE 2 CARBON STEEL A0LF2 1L SS 22 SWIVEL FLANGE 2 CARBON STEEL ALLOY STEEL 2 END CONNECTION CAP SCREW A19 B A20 L 1 Additonal optional materials available upon request.

4 TESTED FOR SAFETY Legacy Valves Delta series LV1 was independently fire tested under API FA with excellent results. The LV1 s leakage above 0 C was less than 2% of allowable, and dropped to less than 2% of allowable after the test was complete. These results validate the Delta series LV1 s mechanical design superiority and build quality. LV1 BALL VALVE SELECTION TABLE WORK PRESSURE TEST PRESSURE PSI PRESSURE CLASS MODEL NUMBER NOMINAL SIZE (IN) BORE DIA (IN),000,00 Test,,000 Test,000 1,000 Test API 000 ANSI 200 API

5 DESIGN EXCELLENCE: CONSTATORQ Legacy s ConstaTorq is the strongest overall performer available in the marketplace today ConstaTorq is a proprietary material developed by Legacy and is built on proven compounds used in the industry for decades. What makes ConstaTorq unique are additional properties such as greater chemical and abrasion resistance, as well as a significant decrease in the coefficient of friction on the surface of the seat. Operating your valve will require approximately % to 0% less torque, and will often require a smaller actuator. Also, ConstaTorq is industrygrade, and prolongs the life of your valve over conventional materials. Very low coefficient of friction Resulting in much lower required torque across a full range of operating pressures Extremely good abrasion resistance Outperforming many flamespray metallic coatings Broad operating temperature range Effective operating range of F to 0 F Excellent chemical resistance ConstaTorq has a crystalline structure that resists the harshest chemicals and is impermiable to gases such as H2S, CO2 and Methane CHEMICAL PROPERTIES Torque Reduction 2 Torque Reduction Ft Lb Valve Torque Comparisons 2 PEERS PEERS PSI A A B C D E F G H I PROPERTIES ConstaTorq Low Friction Wear Resistance Abrasion Resistance Extrusion Resistance Temperature Resistance Chemical Resistance Resilience Water Absorption CO2 consumption PEUHMW URATHANE 0% BRONZE FILLED PTFE CELCON PEEK H G I F E B D C CONSTATORQ PEUHMW URATHANE 0% BRONZE FILLED PTFE CELCON PEEK

6 OUR COMPANY OUR COMPANY Legacy Valves is located in Oklahoma City, Oklahoma and manufactures highpressure, compact manifold floatingball valve systems. Our Company was founded with two objectives in mind; to design the highestquality compact valve systems available in the market today, and to deliver them at competitive prices to our customers. Legacy s management team have decades of combined experience serving operators, distributors and end users in the Oil and Gas market, and understand that success in today s industry requires both a tireless commitment to proven design engineering, as well as reliable, ontime delivery to our customers. OUR QUALITY Legacy s company directive is Design Excellence. Our team understands that consistent delivery of highquality products requires strong working relationships with employees and suppliers. That s why our executive management team is directly involved in every aspect of the company s design, supply chain and manufacturing activities. Additionally, every aspect of Legacy s products has been engineered and tested for performance, reliability, and safety; from the highgrade, USmachined steel in all our products, to the utilization of reliable and innovative new materials for valve components such as seals and ball seats. OUR COMMITMENT We at Legacy understand that in selecting our products, our customers have extended to us a stake in their business and to that trust we are committed. If your company is seeking a highquality valve system at a competitive price, we endeavor to be your solution. CONTACT US For more information on Legacy Valves or its products, please contact sales@legacyvalves.com or call us at () 119. CORPORATE OFFICE 1 S Waterwood Pkwy Suite GD1 Edmond, OK 0 Main:.1.19 Fax: 0..0 MANUFACTURING FACILITY 200 S High Ave Oklahoma City, OK 129