Distinctive Characteristics

Transcription

1 istinctive Characteristics ully Illluminated Toggles Series TL Choice of long or short toggles in translucent colors combine with bright LEs available in red, amber, and green, plus super bright LEs available in white, green, and blue. Black face nut enhances front panel appearance. Antistatic material used for toggle withstands 0 kilovolts electrostatic discharge. Panel seal, achieved with use of optional exterior o-ring, conforms to IP65 of IEC59 Standards. Interior o-ring protects contacts from oil, dust, water, and other conteminants. UL94V-0 flammability rated for base. High insulating barriers protect against crossover. Terminals are molded in and epoxy sealed to lock out flux, dust, and other contaminants. Actual Size

2 General Specifications ully Illluminated Toggles Series TL Electrical Capacity (Resistive Load) Power Level (code W): 15V AC or 50V AC for silver Logic Level (code G): 0.4VA 8V AC/C maximum for gold (Applicable Range 0.1mA ~ 0mV ~ 8V) Note: See Supplement Index (page Z) to find explanation of operating range. Other Ratings Contact Resistance: 10 milliohms maximum for silver; 0 milliohms maximum for gold Insulation Resistance: 1,000 megohms 500V C ielectric Strength: 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts & case for 1 minute minimum Mechanical Life: 50,000 operations minimum Electrical Life: 5,000 operations minimum for silver; 50,000 operations minimum for gold Static Capability: Withstands 0 kilovolts ES minimum Nominal Operating orce: 1.9N for 17.5mm toggle;.5n for 11.0mm toggle Angle of Throw: 5 Materials & inishes Toggle: Housing: Sealing Ring: Base: Movable Contactor: Movable Contacts: Stationary Contact: Lamp Contacts: Power Terminals: Lamp Terminals: Glass fiber reinforced polyamide Nitrile butadiene rubber iallyl phthalate (UL94V-0) Phosphor bronze with silver or gold plating Silver alloy or copper with gold plating Silver plus copper with silver plating or copper with gold plating Beryllium copper with silver plating Copper with silver or gold plating Brass with silver plating Environmental ata Operating Temp Range: Humidity: Vibration: Shock: -10 C through +55 C (+14 through +131 ) 90 ~ 95% humidity for C (104 ) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 1.75 hours 50G (490m/sec ) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Installation Mounting Torque:.98Nm (8.67 lb in) maximum Soldering Time & Temperature: C or 5 70 C Process Seal: Not available Standards & Certifications lammability Standards: UL94V-0 base

3 ully Illluminated Toggles Series TL TYPICAL SWITCH ORERING EXAMPLE TL N A W01 6G POLE PT CIRCUIT ON NONE ON HOUSING A Black TERMINALS, CONTACTS, & RATINGS W01 Silver 15V AC for 17.5mm toggle only G01 Gold 8V AC/C for 11.0mm toggle only S TOGGLE LENGTHS 17.5mm (combines with silver contacts only) 11.0mm (combines with gold contacts only) IMPORTANT: Switches are supplied without UL & CSA marking unless specified. Specific models & ratings noted on General Specifications page. TOGGLE COLORS or Bright C Red Amber Green or Super Bright N No Color LE COLORS Bright 5C Red 5 Amber 5 Green Super Bright 6B White 6 Green 6G Blue ESCRIPTION OR TYPICAL ORERING EXAMPLE TLNAW016G 17.5mm Toggle Length; No Color (matte finish of clear material) Blue, Super Bright LE PT ON-NONE-ON Circuit Black Housing Silver Contacts with 6-amp Rating

4 ully Illluminated Toggles Series TL POLE & CIRCUIT Toggle Position Connected Terminals Throw & Power/Lamp Schematics own Center Up own Center Up Pole Model P TL ON NONE ON 1- - OPEN 1- - PT Notes:Terminal numbers are actually on the switch. Lamp circuit is isolated & requires an external power source. 1 (COM) (+) (-) TOGGLE LENGTHS & COLORS 17.5mm Material: (17.5) S 11.0mm Material: (11.0).433 Colors Available for Bright LE: C Red Amber Green Color Available for Super Bright LE: Combines only with silver Combines only with gold N No Color (Appearance is matte finish of clear material.) HOUSING A Black The housing consists of the 1-piece bushing/case of glass fiber reinforced polyamide in black color only. The glass fiber reinforced polyamide material used for the housing is UL flammability rated 94V-0. CONTACT MATERIALS, RATINGS, & TERMINALS Power Level W Silver Contacts 15V AC & AC 01 G Gold Contacts Logic Level 0.4VA 8V AC/C See Supplement Index (page Z) for complete explanation of operating range. Solder Lug The.043" x " oblong hole accommodates one solid 18-gauge wire or two solid or stranded 0-gauge wires. LE COES & SPECIICATIONS Exopy Seal (1.17) Turret LE Thk = (0.6) (.0) (3.0) (3.5) (1.1) Typ.043 (5.0) Solder Lug Thk = (0.8) Typ Electrical specifications are determined at a basic temperature of 5 C. Lamp circuit is independent of switch operation. If the source voltage is greater than rated voltage, a ballast resistor is required. The ballast resistor calculation and more lamp detail are shown in the Supplement; see Supplement Index (page Z). LE factory assembled Not Available Separately Attention Electrostatic Sensitive evices C or Colored Toggles 5 6 Bright or Clear Toggles Super Bright Color Red Amber Green White Green Blue orward Peak Current I M 30mA 30mA 50mA 30mA 30mA 30mA Continuous orward Current I 0mA 0mA 0mA 0mA 0mA 0mA orward Voltage V.0V.1V.7V 3.6V 3.3V 3.4V Reverse Peak Voltage V RM 4V 4V 4V 5V 5V 5V Current Reduction Rate Above 5 C I 0.3mA/ C 0.3mA/ C 0.50mA/ C 0.50mA/ C 0.40mA/ C 0.40mA/ C Ambient Temperature Range -10 C ~ +55 C -10 C ~ +55 C B G

5 I I ully Illluminated Toggles Series TL TYPICAL SWITCH IMENSIONS 17.5mm Toggle (3.5).138 (1.1) x.043 x (0.6) Typ (1.17) Typ 5 (4.7) Typ (13.5) (0.8) Typ L ( ) I v L ( ) vi (4.5).177 (18.0) Sq.709 (.5).098 (6.0) ia.36 (17.5) (10.0).394 (1.0).87 (0.5) Typ.00 (5.0) Typ TLNAW016G 11.0mm Toggle (3.5).138 (1.1) x.043 x (0.6) Typ (1.17) Typ 5 (4.7) Typ (13.5) (0.8) Typ L ( ) I v L ( ) vi (6.0).36 (18.0) Sq.709 (.5).098 (11.0).433 (10.0).394 (1.0).87 (0.5) Typ.00 (5.0) Typ TLSCAG015C 1 AT57MA Black Hex Nut Used as ace Nut Chrome/Steel STANAR HARWARE 1 AT57M Hex Nut Used as Backup Nut Nickel/Steel 1 AT508 Lockwasher Should Not Be Used w/panel Seal Steel with Chromate/Zinc OPTIONAL HARWARE AT401P O-ring Used for Panel Seal Natural Rubber M1P1 (1.1) ia.476 (14.0).551 (14.0).551 (15.8) ia.6 (1.1) ia.476 (17.5) ia (13.8) ia.543 (16.0).630 (.0) (16.0).630 (.0) (1.0).039 (0.5).00 (1.5).059 Hardware details in Accessories & Hardware section. Maximum Panel Thickness With Standard Hardware 4.0mm (.157") (1.5) ia.49 Panel Cutouts (1.5).060 (1.5) ia.49 (11.5).453 Maximum Panel Thickness With Standard Hardware & AT401P O-ring. 6.0mm (.36")