3M Four-Wall Header.100".100" Latch/Ejector, Straight and Right Angle 3000 Series

Transcription

1 M Four-Wall Header.100".100" Latch/Ejector, Straight and Right ngle 000 Series Military (with M s 518 & N518 polarizing key) and centerbump polarization Optional ejector latches Mounting holes for securing header to board Optional polarizing posts available High temperature insulator option suitable for no lead soldering operations High temperature option suitable for reflow soldering using paste in hole techniques Solder tail option See the Regulatory Information ppendix (RI) in the RoHS compliance section of for compliance information Physical Electrical Environmental Date Modifi ed: October 2, 2012 Insulator: Material: Glass Filled Polyester (PT) Glass Filled Polyester (PT) - (High Temp Option) Flammability: UL 94V-0 olor: Gray (PT), lack (PT) ontact: Material: opper lloy Plating: Underplating: 100 µ [2.54 µm] Nickel - Overall Wiping rea: 0 µ [ 0.76 μm ] Gold Solder Tails: Tin Lead or Matte Tin (See Ordering Information) Marking: M Logo, Part Identification Number and Orientation Triangle Sheet 1 of 4 urrent Rating: 5.00, 1 ontact Powered.00, 6 ontacts Powered 1.75, ll ontacts Powered Rating onditions: EI Method 2, 0 maximum temperature rise, 20% derated. Reference appropriate M Product Specification for detailed current derating curves. Insulation Resistance: > Ω at 500 V D Withstanding Voltage: 1,000 V RMS at Sea Level Temperature Rating: -55 to +105 Process Rating: High Temp PT insulator version: 260, per J-STD-020, single pass PT insulator version: 191, maximum insulator temperature, solder wave process only Moisture Sensitivity Level: 1 (per J-STD-020) High Temp. (PT) versions only UL File No.: E M is a trademark of M ompany

2 M Four-Wall Header.100".100" Latch/Ejector, Straight and Right ngle 000 Series -X0XX Header without Latch Ejector -X2XX Header with Short Ejector/Latch for M Sockets without Strain Relief -XXX Header with Long Ejector/Latch for M Sockets with Strain Relief.68 [17.].08 [2.0].424 ±.010 [ ].97 Ref [24.6].08 [2.0].57 ±.010 [ ] 1.07 Ref [27.2].025 ±.002 Sq Typ [ 0.64 ].7 Ref [9.4].46 Ref [11.7].24 [6.1] D REF [7.6] Dim. E 2X O.100 SEE NOTE # POSITION #1 REF. F Typ Section - (Straight).025 ±.002 Sq Typ [ 0.64 ] Orientation Triangle.21 [5.] Notch (See Table 1 & Note1) Notch (See Table 1).16 [4.1] Notch (See Table 1 & Note 1) F Typ.24 [6.1].0 [7.6].68 [17.].5 [8.9].12 [.0].100 Ref.049 Ref [1.24] Dim. E Section - (Right ngle).020 [0.51] 2X ø [5.00].20 [5.1] Sheet 2 of 4 M is a trademark of M ompany

3 M Four-Wall Header.100".100" Latch/Ejector, Straight and Right ngle 000 Series Table 1 Pin Qty M Part Dimensions Polarizing Number D Notches (27.05) (22.99) (16.89) (12.8) * (29.59) (25.5) (19.4) (15.7) * (2.1) (28.04) (21.97) (17.91) (7.21) 1.05 (.12) (27.05) (22.99) (9.75) (5.66) (29.59) (25.5) (44.8) (40.74) 1.65 (4.67) (0.61) (49.91) (45.82) (9.75) (5.69) (52.45) (48.6) (42.29) (8.2) (57.5) (5.44) (47.7) (4.1) (62.61) 2.05 (58.52) (52.45) (48.9) (70.2) (66.14) 2.65 (60.07) (56.01) (82.9).105 (78.84) (72.77) (68.71) (95.6).605 (91.54).65 (85.47).205 (81.41) (100.71).805 (96.62).565 (90.55).405 (86.49) * vailable without center notch. ontact M. Inch (mm) Tolerance Unless Noted Inch ±.1 ±.01 ±.005 [ ] Dimensions for Reference only Table 2 M Part Number Suffix ontact Tail Dim E Pin ross Section Dim G -5XX2-6XX2 Solder Tail for.062 (1.57) Thick P oard.112 ±.010 (2.84) Dim F.0245 ±.0005 (0.622) Diagonals.028 ±.001 (0.71) orner Radii.0075 Ref (0.191) 0.05 ±.00 (0.89) (See Note ) -5X0 Solder Tail for 0.94 (2.9) to.125 (.18) -6X0 Thick P oard.155 ±.010 (.94).0245 ±.0005 (0.622).028 ±.001 (0.71).0075 Ref (0.191) 0.05 ±.00 (0.89).00 [7.62] Side to Side Stackability or ø.116 [2.95] ø.106 [2.69] Dim G ø.106 or ø.116 [2.69] [2.95].41 [10.4] Max to Edge of P for Daisy hain Dim G "Y".060 [1.52].100 ± ± [8.94] Recommended Mounting Hole Pattern (Straight).029 [0.74].100 ± ± [5.89] Recommended Mounting Hole Pattern (Right ngle) Notes: 1. Notches & will accomodate M Polarizing Keys (M Part #518 or #N518). 2. Mounting hardware: From solder side of pc board use #4-24 thread cutting screw (M Part # 41-5) and.116 [2.95] dia mounting hole. For right angle version only, #2-56 bolt and nut (M Part # 41-6) with.106 [2.69] dia mounting hole may be used. See illustrations on page 4.. The recommended P hole size for the kinked tail positions on the.112 solder tail connector is.05 ±.002. See page 4 for kink position details (K2 version). 4. ontact your M sales representative for custom requirements. Ordering Information N = High Temp lack (PT)/(R Plating Req d) lank = Std. Temp Gray (PT) /(lank or U Pltg. Req d.) M Part Number (See Table 1) Pin onfiguration 5 = Right ngle Solder Tails 6 = Straight Solder Tails XXXX-XXXXXX Latch/Ejector System 0 = No Latch/Ejector installed 2 = Short Roll Pin Latch/Ejectors = Long, Roll Pin Latch/Ejectors 5 = Short, Snap-In Latch/Ejectors 6 = Long, Snap-In Latch/Ejectors Plating R = 0 μ [ 0.76 μm ] Gold and 200 μ [ 5.08 μm ] Matte Tin (pp. E1 & 1 pply) lank or U = 0 μ (0.76 μm ] Gold and 200 μ [ 5.08 μm ] Tin Lead (pp. E & 2 pply) Tail 02 = for.062 [1.57] thick board 0 = for.094 to.125 [2.9 to.18] thick board K2 = kinked for.062 [1.57] thick board Sheet of 4 M is a trademark of M ompany

4 M Four-Wall Header.100".100" Latch/Ejector, Straight and Right ngle 000 Series Part ustomization This spec sheet details our standard offering. M has several capabilities that can provide a part tailored to your specific needs. sk your M sales representative or customer service for more details..18 [8.08].100 Dia Polarizing Post LP lack PT Gray oth snap in and roll pin latches may be ordered separately. Snap in and roll style latches are dimensionally and functionally equivalent. If ordering snap-in or roll pin style latches separately, please use the below chart. Standard Temperature (PT) (PT) (PT) (PP) Short Latch Long Latch Latch Style olor Roll Pin Gray N505-2 N505- Roll Pin lack Snap-In Gray N505-0 N505-1 Snap-In lack Selective pin removal (T or other compatability) Wire wrap tails styles Mounting Hardware Note: Insert Post into one mounting hardware hole on bottom of header. Set post to protrude.115 [2.92]. Total Number of Pins 2500 & 000 Series Shrouded Header Number of Tails Kinked Positions Kinked (Installed from bottom of board) 41-6 (Must be inserted prior to latch on vertical headers) Kinked Tail Detail: Kink is located.05 below bottom surface of plastic. External radius of kink toward part centerline..1 [7.9].50 [12.7] Polarizing Keys Panhead Thread utting Screw: #4-24 X 5/16 Type: US Std T, Federal G Hex Head olt, Nut and Washer olt - #2-56 X 1/2 Dim N518 LP lack PT Gray & 6 Material - Stainless Steel reakaway Tab.4 Ref [8.6].15 [.8] Note: #2216 / Scotchweld can be used to adhere keys..09 [2.] Sheet 4 of 4 M is a trademark of M ompany

5 M is a trademark of M ompany. Important Notice ll statements, technical information, and recommendations related to M s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. efore using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. ny statements related to the product which are not contained in M s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of M. Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. M MKES NO OTHER WRRNTIES INLUDING, UT NOT LIMITED TO, NY IMPLIED WRRNTY OF MERHNTILITY OR FITNESS FOR PRTIULR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at M s option, to replace or repair the M product or refund the purchase price of the M product. Except where prohibited by law, M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this M product, regardless of the legal theory asserted. M Electronics Solutions Division 6801 River Place lvd. ustin, TX U.S Please recycle. Printed in US. M ll rights reserved. RI-2217-E