C45 / TS Average Chemical analysis. Steel properties. Standards. Heat treatment. Applications. C% Si% Mn%

Transcription

1

2 C45 / TS 1730 C% Si% Mn% approx Water 57 max. 207 Hardness after quenching Shell-hardenable steel featuring hard surface and tough core. AISI 1045 Components for tools (e.g. base plates for plastic moulds and pressure casting moulds). Also suitable for hand tools, pliers and agricultural tools of all kinds.

3 TS 2311 C% Mn% Cr% Mo% Pre-hardened plastic mould steel, hardness in as-delivered condition 280 to 325 HB. Good machinability, suitable for texturing, better polishability than TS Oil or saltbath, C max. 235 Hardness after quenching AISI P20 Plastic moulds, mould frames for plastic moulds and pressure casting moulds and recipient sleeves. at C m/(m K) at C

4 TS 2312 C% Si% Mn% Cr% Mo% S% plastic mould steel with a hardness in as-delivered condition of 280 to 325 HB. Improved machinability in comparison with TS Polishable (Annealed) approx () approx. 30 under tempering temperature Oil or saltbath, C 46 max. 235 Hardness after quenching AISI P20+S Plastic moulds, mould frames for plastic and pressure casting moulds, recipient sleeves, brake dies. at C m/(m K) Annealed 10-6 m/(m K) at C 1 2 Annealed

5 TS 2343 C% Si% Cr% Mo% V% High hot tensile strength and toughness. Good thermal conductivity and insusceptibility to hot cracking. Can be water-cooled to a limited extent approx Air, oil or saltbath, 5 C 5 max. 230 Hardness after quenching AISI H11 AFNOR Z38CDV5 Besides applications typical for the area of hot-work steels, this grade is mainly used for ejector pins, tool holders and shrink fit chucks. Please notice TS 2343 is also available in our PREMIUM MASTER version 2343 ESR. at C m/(m K) at C 20 3 Annealed

6 TS 2344 C% Si% Cr% Mo% V% High hot-wear resistance and hot tensile strength as well as good toughness, thermal conductivity and insusceptibility to hotcracking. Can be water-cooled to a limited extent approx Air, oil or saltbath, 5 C 56 5 max. 230 Hardness after quenching 6 32 AISI H13 AFNOR Z40CDV5 Besides applications typical for the area of hot-work steels, this grade is mainly used for ejector pins, tool holders and shrink fit chucks. Please notice TS 2344 is also available in our PREMIUM MASTER version 2344 ESR. at C m/(m K) at C 20 3 Annealed

7 TS 2714 C% Cr% Mo% Ni% V% Tough die steel with high tempering resistance and good through-hardening properties. This grade is usually supplied in annealed condition or quenched and tempered to a working hardness of 370 to 410 HB (round) or 355 to HB (square, flat). 6 approx Oil Air max. 2 Hardness after quenching AISI L6 AFNOR 55NCDW7 Standard steel for forging dies of all types, press dies, extrusion dies, retainer plates, armoured trim dies, hot-shear blades and tool holders at C m/(m K) at C

8 TS 2738 C% Mn% Cr% Ni% Mo% Pre-hardened plastic mould steel, hardness in as-delivered condition 280 to 325 HB. Good machinability, suitable for texturing, improved through hardening in comparison to , good polishability Polymer or oil max. 235 Hardness after quenching AISI P20+Ni Large plastic moulds with deep engravings and intensive impacts on the core. TS 2738 is the logical development of TS 2311, a pre-hardened plastic mould steel for use in large moulds, which also have to display high core strength. The additional nickel content of 1 % increases through hardening. TS 2738 is a micro-alloyed, vacuum-degassed steel with the following excellent features: good machinability, outstanding polishability, good texturing properties. Please notice TS 2738 is also available in our PREMIUM MASTER version 2738 ESR. at C m/(m K) at C

9 TS 2738 HH C% Mn% Cr% Ni% Mo% Polymer or oil max. 235 Hardness after quenching Heat-treated mould steel with improved quenching and tempering properties in comparison to TS Good machinability, polishable, weldable and can easily be textured. TS 2738 HH is either available at a hardness of HB or HB. This grade offers substantial improvements, especially for building larger and complex moulds. Specific modifications of the grade's components as well as additional smelting and secondary metallurgy ensure TS 2738 HH's outstanding properties. TS 2738 HH is highly suitable for large-format plastic injection and extrusion moulds with deep engraving and high demands on core strength, such as with bumpers, tailgates, fenders, spoilers, instrument panels and TV housings to name a few. At a supplied hardness of HB, maximum wear resistance is guaranteed. at C m/(m K) at C