MATERIAL SAFETY DATA SHEET

Transcription

1 MATERIAL SAFETY DATA SHEET Page 1 of 7 NOVADENT: TAPETRIX ADHESIVE Issue Date: January 14, 2007 MATERIAL SAFETY DATA SHEET PRODUCT: Cognident-Novadent Cat# 100, 105, Tapetrix Adhesive, Temporary Dental Adhesive, 4g syringe SECTION 1: PRODUCT AND COMPANY IDENTIFICATION COMMON or CHEMICAL NAME: A blend of synthetic waxes and thickening agents in polymeric carrier Distributor: Cognident-Novadent Emergency Telephone: 8777 Auburn Folsom Rd (888) Granite Bay, CA General Information: USA (916) SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS Hazardous ingredients Other ingredients Product Contents: 4g Tapetrix Adhesive, Temporary Dental Adhesive SECTION 3: HAZARDS IDENTIFICATION For potential health hazards: SEE Section 11 below. No other significant critical hazards to man or the environment are reasonably foreseen. SECTION 4: FIRST AID MEASURES INHALATION:. SKIN CONTACT: Wash with soap and water. EYE CONTACT: Flush immediately with copious amounts of water. INGESTION: No harm anticipated from materials in quantities as packaged.

2 MATERIAL SAFETY DATA SHEET Page 2 of 7 SECTION 5: FIRE-FIGHTING MEASURES SUITABLE EXTINGUISHING MEDIA: Water contact acceptable. EXTINGUISHING MEDIA WHICH SHOULD NOT BE USED:. SPECIAL EXPOSURE HAZARDS FROM COMBUSTION PRODUCTS: in quantities as packaged. SPECIAL PROTECTIVE EQUIPMENT FOR FIREFIGHTERS:. SECTION 6: ACCIDENTAL RELEASE MEASURES PERSONAL PRECAUTIONS: Avoid contact of skin or eyes. Wash hands with soap and water if contact occurs. ENVIRONMENTAL PRECAUTIONS: Dispose of in accordance to all federal, state, local regulations. METHOD FOR CLEANING UP: Wipe up with soap, water and paper towels. SECTION 7: HANDLING AND STORAGE HANDLING PRECAUTIONS: Avoid contact of skin or eyes. SAFE STORAGE CONDITIONS: Store at room temperatures. OTHER RESTRICTIONS OR RECOMMENDATIONS:. SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION RESPIRATORY PROTECTION & VENTILATION: Not required. PROTECTIVE CLOTHING OR EQUIPMENT: Not required under normal handling. UNUSUAL WORK/HYGIENIC PRACTICES: Avoid prolonged contact with skin; wash with soap and water.

3 MATERIAL SAFETY DATA SHEET Page 3 of 7 SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES Appearance: Colored (blue/green) paste Ph: Neutral Melting Point/Range: Auto-Ignition Temperature: Explosive Limits in Air: Vapor Pressure (mm Hg): Not Applicable Specific Gravity (H2O = 1) ca 1 Reactivity in Water: Not reactive Odor: Slight odor Boiling Point/Range: Flash Point: Flammability: Low Oxidizing Properties: Vapor Density (Air = 1): ` Solubility in Water: Partially soluble Other Data: SECTION 10: STABILITY AND REACTIVITY Stability: Conditions of Instability: Incompatibility with Various Substances: Hazardous Decomposition Products: Conditions to Avoid: Hazardous Polymerization: Stable Contact with strong oxidizers known Strong oxidizers SECTION 11: TOXICOLOGICAL INFORMATION Potential Acute Health Effects: Potential Chronic Health Effects: Sign and Symptoms of Exposure: Medical Conditions Generally Aggravated by Exposure: Carcinogenic or Potential Carcinogenic effects: Other Potential Health Effects: known known known known No ingredient listed as a carcinogen known SECTION 12: ECOLOGICAL INFORMATION No ecological damage or impact anticipated upon exposure to environment in quantities as packaged SECTION 13: DISPOSAL CONSIDERATIONS Waste Disposal: Do not dispose into sink. Dispose in accordance with all federal, state, and local regulations. SECTION 14: TRANSPORT INFORMATION

4 MATERIAL SAFETY DATA SHEET Page 4 of 7 UN Classification: Identification: Special Provisions for Transport: Avoid elevated temperatures and high intensity light SECTION 15: REGULATORY INFORMATION U.S. FDA Dental Device: EC Medical Device Directive: Not a dental device Not a dental device SECTION 16: OTHER INFORMATION Some of the information presented and conclusions drawn herein are from sources other than direct test data on the product itself. The information in this MSDS was obtained from sources that we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or method of handling, storage, use and disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage, or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. If the product is used as a component in another product or used in a way other than recommended by the Company, this MSDS information may not be applicable.

5 MATERIAL SAFETY DATA SHEET Page 5 of 7 MATERIAL SAFETY DATA SHEET NOVADENT TAPETRIX PTFE TAPE Issue Date: January 14, 2007 PRODUCT: Novadent Cat #100, 106, 110, 112, 116, 118, 150, 175, Tapetrix PTFE Tapes SECTION 1: CHEMICAL PRODUCT AND COMPANY IDENTIFICATION Distributor: Cognident-Novadent Emergency Telephone: 8777 Auburn Folsom Rd (888) Granite Bay, CA General Information: USA (916) Product Synonyms: FSN : FSN SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS Hazardous Ingredients CAS # Percentage Other Ingredients Polytetrafluoroethylene SECTION 3: HAZARDS IDENTIFICATION EMERGENCY OVERVIEW Odorless, white, solid tape. As sold, this product presents no known health hazards. At temperatures above 535 degrees F, this polymer will break down and the fumes could cause a temporary flu-like illness. No smoking while handling this material. POTENTIAL HEALTH EFFECTS: EYE: No harmful effects anticipated for product as sold. SKIN CONTACT: No harmful effects anticipated for product as sold. SKIN ABSORPTION: Skin absorption is unlikely due to physical properties of product. INGESTION: No harmful effects anticipated for product as sold. LD50 (PTFE resin):

6 MATERIAL SAFETY DATA SHEET Page 6 of mg/kg in rats. INHALATION: Inhalation is unlikely due to physical properties of product. CHRONIC EFFECTS/CARCINOGENICITY: PTFE is not listed by IARC, NTP, OSHA, or ACGIH as a carcinogen. No significant adverse effects anticipated. Repeated oral doses of the polymer resin yielded no toxic effects except for alteration in the number of circulating white blood cells after long-term dosing. Testing demonstrated no developmental toxicity in animals, and no genetic damage in animals or in bacterial cell cultures. (1) SECTION 4: FIRST AID MEASURES INHALATION: Unlikely route of entry for product as sold. If exposed to fumes from overheating or combustion, move to fresh air. Consult a physician if symptoms persist. SKIN CONTACT: This product is not likely to be hazardous by skin contact, but if redness or itching develops, then cleansing the skin with water after use is advisable. EYE: Unlikely route of entry for product as sold. If mechanical irritation occurs flush eyes with plenty of water. Consult physician if symptoms persist. INGESTION: Unlikely route of entry for product as sold. Consult physician if necessary. NOTES TO PHYSICIAN: Inhaling fumes of decomposition products can induce temporary influenza-like symptoms which are described as polymer fume fever. These symptoms include fever, cough and malaise. SECTION 5: FIRE FIGHTING MEASURES FLASH POINT: Does not flash AUTO-IGNITION TEMPERATURE: Not available METHOD: Open cup FLAMMABILITY LIMITS: EXTINGUISHING MEDIA: Water, foam, dry chemical or CO2 FIRE AND EXPLOSION HAZARDS: PTFE will burn in an atmosphere of 95% oxygen when an ignition source is present. Hazardous gases/vapors produced in a fire are hydrogen fluoride (HF), carbonyl fluoride, perfluoroolefins, and carbon monoxide and low molecular weight fluorocarbons. FIRE FIGHTING EQUIPMENT: Wear self-contained breathing apparatus. Wear full protective equipment. Protect from hydrogen fluoride fumes, which react with water to form hydrofluoric acid. Wear neoprene gloves when handling refuse from a wire involving PTFE. SECTION 6: ACCIDENTAL RELEASE MEASURES Sweep to avoid slipping hazard. SECTION 7: HANDLING AND STORAGE

7 MATERIAL SAFETY DATA SHEET Page 7 of 7 Enforce no smoking rule in areas where PTFE is handled or stored. Wash hands and face after handling to avoid transfer of PTFE onto cigarettes and tobacco. SECTION 8: EXPOSURE CONTROLS.PERSONAL PROTECTION No special personal protection or exposure controls are indicated for this product as sold except those mentioned in section 7. SECTION 9: PHYSICAL & CHEMICAL PROPERTIES Melting Point: 648 degrees F Water Solubility: Insoluble Odor: Appearance: White solid tape SPG: Greater than.5 SECTION 10: STABILITY & REACTIVITY Stability: Hazardous Polymerization: Incompatibility: Hazardous Decomposition Products: Particulate matter: Stable at normal temperatures and storage conditions. Will not occur. Reacts with molten alkali metals and interhalogen compounds. Above 535 degrees F, this product may evolve toxic gaseous materials such as hydrogen fluoride, carbonyl fluoride and perfluoroolefins. Evolved from overheating may cause polymer fume fever. OTHER INFORMATION: Waste Disposal: Discarded product is not a hazardous waste under RCRA, 40 CFR 261. Preferred options for disposal are recycling and landfill. Incinerate only if incinerator is capable of scrubbing out hydrogen fluoride and other acidic combustion products. Treatment, storage, transportation, and disposal must be accordance with applicable federal, state and local regulations. DOT: Not regulated TSCA Inventory: Listed SARA 313/302: Not listed SARA 311/312: Not hazardous California: Not listed New Jersey: Not listed Pennsylvania: Hazardous Substance List (Prop 65) References: 1. Supplier MSDS This information is given in good faith but no warranty, expressed or implied, is made.