3M Pak 100 L/E Pinless Header.100".100" Straight, 4-Wall 3000 Series

Transcription

1 Optional ejector latches Shrouded to minimize physical and chemical pin damage Special holes secure pinless header to back panel Mounting holes to further secure header to board Stand-off height allows for one layer wire wrap See the Regulatory Information ppendix (RI) in the RoHS compliance section of for compliance information Date Modified: May 22, 2012 Sheet 1 of 5 Physical Insulator: Material: Glass Filled Polyester (PBT) Flammability: UL 94V-0 Color: Gray Marking: M Logo, Part Identification Number and Orientation Triangle *RoHS = Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment RoHS compliant means that the product or part does not contain any of the following substances in excess of the following proposed maximum concentration values in any homogeneous material (unless exempt under RoHS): (a) 0.1% (by weight) for each of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. UL File No.: E M is a trademark of M Company

2 Pin Quantity Part Number Table 1 Dimensions B D [44.8] [40.77] 1.21 [0.7] [52.4] [48.9] 1.51 [8.] [62.6] 2.05 [58.55] 1.91 [48.5] [70.2] [66.17] 2.21 [56.1] [82.9].105 [78.87] 2.71 [68.8].08 [2.0].424 ±.010 [10.77] 1.01 [25.7].08 [2.0].57 ±.010 [14.55] 1.11 [28.2] 1.11 [28.2] No Ejector/Latch.7 [9.4] Short Ejector/Latch for M Sockets without Strain Relief.46 [11.7] [10.7] Long Ejector/Latch for M Sockets with Strain Relief Ejector Only Note: This Ejector is a Nickel plated Zinc lloy casting. 8X.01 ±.002 [.79 ] (See Note 1 & 2 ) See Note 1.16 [4.06].2 [8.1] Position 1 D 2X.100 (See Note ) B Position 1 Orientation Triangle See Note 4.25 [6.4].21 [5.].0 [7.6].22 [5.6].25 [6.4].72 [18.].8 [9.65] 64XX.17 [4.].58 [14.7].16 [4.1].100 2X.10 [2.5] Section - TS Sheet Sheet 2 of 2 of 5 M is a trademark of M Company

3 Table 1 M Part Number Suffix Dimension H [21.8] [40.6] [45.2] [4.2] Backplane Pin Field Recommendations.050 [1.27].5 Typ [8.95].106 or.116 Typ [2.69] [2.95] (See Note ) H.025 ±.001 Square [0.64].580 ±.010 [14.7] (For Flush Mounting).00 [7.62] Notes: 1.ccepts.025 ±.001 sq pins. 2.Four smaller holes at each end used for retention..ccepts Rear and Front entry mounting hardware: Rear entry: #4-24 thread cutting screw M Part # 41-5 (.116 [2.95] mounting hole) Front entry (Prior to installation of Latch): #2-56 bolt and nut M Part # See illustrations on page 4. (.106 [2.69] mounting hole) 4.These polarization notches will accomodate M Polarization Keys 518. Inch (mm) Tolerance Unless Noted Inch ±.1 ±.01 ±.005 [ ] Dimensions for erence only Ordering Information 64XX-9X00 Pin Quantity: (See Table 1) Latch/Ejector System 0= No Latch/Ejectors 2= Short, Roll Pin Latch/Ejectors (M Part #505-2 ) = Long, Roll Pin Latch/Ejectors (M Part #505- ) 4= Roll Pin Ejectors (M Part #505-4) Sheet of 5 M is a trademark of M Company

4 Polarizing Post.21 [8.15] 201- P B T G ra y L C P B la c k.100 Dia Note: Insert Post into one mounting hardware hole on bottom of header. Set post to protrude.115 [2.92] Polarizing Keys Dim N518 LCP Black PBT Gray.02 Breakaway Tab.15 [.8].4 [8.6].09 [2.] Note: #2216 B/ Scotchweld can be used to adhere keys (Installed from bottom of board) Mounting Hardware 41-6 (Must be inserted prior to latch on vertical headers).1 [7.9].50 [12.7] Panhead Thread Cutting Screw: #4-24 X 5/16 Type: US Std BT, Federal BG 41-5 & 6 Material - Stainless Steel Hex Head Bolt, Nut and Washer Bolt - #2-56 X 1/2 Not for use with Condo headers. Sheet 4 of 5 M is a trademark of M Company

5 Important Notice ll statements, technical information, and recommendations related to M s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. ny statements related to the product which are not contained in M s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of M. Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. M MKES NO OTHER WRRNTIES INCLUDING, BUT NOT LIMITED TO, NY IMPLIED WRRNTY OF MERCHNTBILITY OR FITNESS FOR PRTICULR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at M s option, to replace or repair the M product or refund the purchase price of the M product. Except where prohibited by law, M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this M product, regardless of the legal theory asserted. M Electronics Solutions Division 6801 River Place Blvd. ustin, TX U.S Please recycle. Printed in US. M ll rights reserved. RI-2217B-E M is a trademark of M Company.