ASTM D256 Standard test methods for determining the izod pendulum impact resistance of plastics

Transcription

1 IAS Accreditation Number Company Name Address Contact Name Telephone Effective Date of Scope November 15, 2018 Accreditation Standard ISO/IEC 17025:2005 TL-385 Bangalore Research & Development Technology Centre Plot #5, Road #8, E.P.I.P. Whitefield, Bangalore (Karnataka) India H. Manjunatha, Lab Supervisor-TP (MR) Physical ASTM D256 Standard test methods for determining the izod pendulum impact resistance of plastics ASTM D395 Standard test methods for rubber property compression set (methods B&C) ASTM D412 Standard test methods for vulcanized rubber and thermoplastic elastomers-tension (except method B) ASTM D471 ASTM D523 ASTM D624 ASTM D638 ASTM D648 ASTM D746 Standard test method for rubber property-effect of liquids Standard test method for specular gloss Standard test method for tear strength of conventional vulcanized rubber and thermoplastic elastomers Standard test method for tensile properties of plastics Standard test method for deflection temperature of plastics under flexural load in the edgewise position Standard test method for brittleness temperature of plastics and elastomers by impact ASTM D790 Standard test methods for flexural properties of unreinforced and reinforced plastics and electrical insulating materials ASTM D792 Standard test methods for density and specific gravity (relative density) of plastics by displacement International Accreditation Service, Inc Saturn Street, Suite 100, Brea, California U.S.A Telephone Page 1 of 6

2 ASTM D955 ASTM D1004 Standard test method for measuring shrinkage from mold dimensions of thermoplastics (types A and B) Standard test method for tear resistance (Graves tear) of plastic film and sheeting ASTM D1238 Standard test method for melt flow rates of thermoplastics by extrusion plastometer (procedures A, B and C) ASTM D1415 ASTM D1525 ASTM D1693 ASTM D2240 ASTM D2584 ASTM D3012 ASTM D3045 ASTM D3418 ASTM D3641 ASTM D3677 ASTM D3763 ASTM D4101 ASTM D4703 ASTM D6110 Standard test method for rubber property-international hardness Standard test method for vicat softening temperature of plastics (except method D) Standard test method for environmental stress-cracking of ethylene plastics Standard test method for rubber property durometer hardness Standard test method for ignition loss of cured reinforced resins Standard test method for thermal-oxidative stability of polypropylene using a specimen rotator within an oven Standard practice for heat aging of plastics without load Standard test method for transition temperatures and enthalpies of fusion and crystallization of polymers by differential scanning calorimetry Standard practice for injection molding test specimens of thermoplastic molding and extrusion materials Standard test methods for rubber identification by infrared spectrophotometry Standard test method for high speed puncture properties of plastics using load and displacement sensors Standard classification system and basis for specification for polypropylene injection and extrusion material Standard practice for compression molding thermoplastic materials into test specimens, plaques, or sheets Standard test method for determining the Charpy impact resistance of notched specimens of plastics TL-385 Page 2 of 6

3 ASTM D6370 ASTM D7869 ASTM E168 ASTM E831 ASTM E1131 ASTM E1252 FLTM BN FLTM BO-116 GM 3943 GMW GMW ISO 34-1 ISO 48 ISO 37 ISO 75-1 ISO 75-2 ISO 105-A02 ISO 105-B06 ISO I78 Standard test method for rubber compositional analysis by thermogravimetry Standard practice for xenon arc exposure test with enhanced light and water exposure for transportation coatings Standard practices for general techniques of infrared quantitative analysis Standard test method for linear thermal expansion of solid materials by thermomechanical analysis Standard test method for compositional analysis by thermogravimetry Standard practice for general techniques for obtaining infrared spectra for qualitative analysis Resistance to scratching Resistance to interior weathering Scratch and Mar resistance of plastics, five Arm Test Colorfastness to artificial weathering Scratch and Mar resistance tear strength part 1: trouser, angle and crescent test pieces hardness (hardness between 10 IRHD and 100 IRHD) Rubber, vulcanized or thermoplastic determination of tensile stress- strain properties Plastics - determination of temperature of deflection under load part 1: general test method Plastics - determination of temperature of deflection under load part 2: plastics and ebonite Textiles - tests for colour fastness part A02: grey scale for assessing change in colour Textiles tests for colour fastness part B06: colour fastness and ageing to artificial light at high temperatures: xenon arc fading lamp test Plastics - determination of flexural properties TL-385 Page 3 of 6

4 ISO 179 ISO 180 ISO 188 ISO 293 ISO ISO 306 Plastics - determination of Charpy impact strength Plastics - determination of izod impact strength Rubber, vulcanized or thermoplastic - accelerated ageing and heat resistance tests Plastics compression moulding of test specimens of thermoplastic materials Plastics - injection moulding of test specimens of thermoplastic materials - part 1: general principles, and moulding of multipurpose and bar test specimens Plastics thermoplastic materials determination of vicat softening temperature ISO Plastics - determination of tensile properties - part 1: general principles ISO ISO 812 ISO ISO 868 ISO ISO ISO ISO 1817 ISO Plastics - determination of tensile properties - part 2: test conditions for moulding and extrusion plastics Rubber, vulcanized or thermoplastic determination of low- temperature brittleness compression set part 1: at ambient or elevated temperatures - CORR: March 31, 2009 Plastics and ebonite - determination of indentation hardness by means of a durometer (shore hardness) - CORR 14577: July 11, 2003 Plastics determination of the melt mass-flow rate (MFR) and melt volume flow rate (MVR) of thermoplastics part 1: standard method Plastics - methods for determining the density of noncellular plastics part 1: immersion method, liquid pycnometer (method A) Plastics - polypropylene (PP) molding and extrusion materials - part 2: preparation of test specimens and determination of properties the effect of liquids Plastics determination of ash part 1: general methods (method A) TL-385 Page 4 of 6

5 ISO 3795 ISO ISO ISO ISO 7619 ISO Road vehicles, and tractors and machinery for agriculture and forestry - determination of burning behavior of interior materials Plastics - methods of exposure to laboratory light sources - part 1: general guidance Plastics - methods of exposure to laboratory light sources - part 2: xenon-arc lamps Plastics - determination of puncture impact behavior of rigid plastics - part 2: instrumented impact testing Determination of Shore Hardness Plastics differential scanning calorimetry (DSC) part 1: general principles ISO Plastics - differential scanning calorimetry (DSC) - part 2: determination of glass transition temperature and glass transition step height ISO Plastics differential scanning calorimetry (DSC) part 3: determination of temperature and enthalpy of melting and crystallization ISO Plastics differential scanning calorimetry (DSC) - part 4: determination of specific heat capacity ISO Plastics - differential scanning calorimetry (DSC) - part 5: determination of characteristic reaction-curve temperatures and times, enthalpy of reaction and degree of conversion ISO Plastics - thermogravimetry (TG) of polymers - general principles ISO Plastics - thermo mechanical analysis (TMA) - part 1: general principles ISO Plastics - thermo mechanical analysis (TMA) - part 2: determination of coefficient of linear thermal expansion and glass transition temperature SAE J 1756 Determination of the fogging characteristics of interior automotive materials SAE J 2412 Accelerated exposure of automotive interior trim components using a controlled irradiance xenon-arc apparatus TL-385 Page 5 of 6

6 SAE J 2527 SAE J 1545 Performance based standard for accelerated exposure of automotive exterior materials using a controlled irradiance xenon- arc apparatus Instrumental color difference measurement for exterior finishes, textiles and colored trim FLTM: Ford Laboratory Test Method GM: General Motors GMW: General Motors Worldwide SAE: Society of Automotive Engineers TL-385 Page 6 of 6