Automotive Application AUTOMOTIVE APPLICATION

Transcription

1

2 Thermoplastic s compounds are widely used in the automotive industry. The producer has developed polyamide and polypropylene special grades for automotive application with improved mechanical parameters (flexural modulus, impact properties etc.) and increased low temperature resistance, materials suitable for long-term stability at elevated temperatures, materials with low shrinkage and high customer performance (e.g. low emissions, scratch resistant, UV-stability, low tiger stripe). The Polyplastic portfolio includes grades for exterior, interior and under-the-hood applications. Materials are available in the customer s choice of colour. All materials are approved and used at Russian OEMs as well as at big international OEMs like GM, Volkswagen and Renault.

3 Automotive Application 01 AUTOMOTIVE APPLICATION

4 Material technical specification Polyamide 6 compound Armamid PA6 GF 30-2HSM-902 Polyamide composite material with 30% glass fibers, heat stabilized. Application is air intake manifold and other under the hood parts where long-term stability at 150 C as working temperature is required. Properties Test Method Unit Value PHYSICAL-MECHANICAL Density ISO1183 g/cm 3 1,37 Tensile strength at break ISO 527-1/-2 MPa 165 Tensile modulus ISO 527-1/-2 MPa 9200 Elongation at break ISO 527-1/-2 % 4,9 Flexural modulus ISO 178 MPa 7900 Flexural strength ISO 178 MPa 240 Charpyimpactstrengthnotched at 23 C ISO 179/1eA kj/m 2 12 Charpyimpactstrengthnotched at -30 C ISO 179/1eA kj/m 2 8 Charpyimpactstrengthunnotched at 23 C ISO 179/1eU kj/m 2 75 Charpyimpactstrengthunnotched at -30 C ISO 179/1eU kj/m 2 63

5 THERMAL HDT, 1,8 MPa ISO 75-1/-2 C 204 HDT, 0,45 MPa ISO 75-1/-2 C 217 TECHNICAL Melt Flow Rate (250 C; 2,16 kg) ISO 1133 g/10min 9 PROCESSING Melt temperature range С Mould temperature С 80 Drying temperature С 85 Drying time h 2-4 Comments: * dry in gis not necessary needed in case material is stored in dry warehouse Automotive Application

6 Material technical specification Polyamide 6 compound Armamid PA6 GF 30 HS-901 This grade is 30 % glass reinforced polyamide 6 for injection molding, heat stabilized. Application is engine cooling fan shroud. It is designed for under the hood application (air fans, engine covers, air dryer housings, air fans for exhausting systems, intake manifold). The finished parts are: - fully functional and completely undamaged at low temperature and after aging 3000h 150 C - good Dimensional stability. - no cracks or another defects after thermal cycles. Properties Test Method Unit Value PHYSICAL-MECHANICAL Density ISO 1183 kg/m Ash content ISO 3451 % 30 Stress at brake ISO 527 MPa 172 Strain at break ISO 527 % 4,9 Tensile modulus ISO 527 MPa 9700

7 Flexural modulus ISO 178 MPa 8500 Flexural Strength at Max. Load ISO 178 MPa 240 Unnotched Charpy impact strength at +23 C ISO 179/1eU kj/m 2 78 Notched Charpy impact strength at +23 C ISO 179/1eA kj/m 2 10 THERMAL HDT, 1,8 MPa ISO 75/A C 203 TECHNICAL Moulding shrinkage, parallel ISO % 0,1-0,2 Moulding shrinkage, normal ISO % 0,6-0,8 PROCESSING Melt temperature range C Mold temperature C 80 Drying time, Dehumidified dryer C 4-6 Drying temperature C 85 Processing Moisture Content % < 0,2 Automotive Application

8 Material technical specification Polypropylene s compound Armlen PP 3IM Impact modified polypropylene composite material for interior trim application (e.g. door panels). Available in customer s color. Properties Test Method Unit Value PHYSICAL-MECHANICAL Density ISO 1183 g/cm 3 0,90 Flexural modulus ISO 178 MPa 850 Tensile modulus ISO MPa 1000 Izod impact strength notched at 23 C ISO 180 kj/m 2 40 THERMAL HDT, 0,45 MPa ISO 75A C 88 HDT, 1,80 MPa ISO 75A C 55

9 TECHNICAL Melt Flow Rate (230 С; 2,16 kg) ISO 1133 g/10min 14 Moulding shrinkage, parallel ISO % 1,5 Moulding shrinkage, normal ISO % 1,5 PROCESSING Melt temperature range С Mould temperature 60 Drying temperature С - Drying time h - Comments: * drying is not necessary needed in case material is stored in dry warehouse Automotive Application

10 Material technical specification Polypropylene s compound Armlen PP 12IM-895 (Togozai aproach) Impact modified polypropylene composite material for bumper painted and unpainted applications, colored in customer color, UV-resistant. Properties Test Method Unit Value PHYSICAL-MECHANICAL Density ISO 1183 g/cm 3 1,01 Tensile strength at yield ISO MPa 18 Elongation at break ISO % 90 Flexural modulus ISO 178 MPa 1570 Flexural strength ISO 178 MPa 23 Izod impact strength unnotched at 23 C ISO 179 kj/m 2 NB Izod impact strength notched at -20 C ISO 179 kj/m 2 9

11 THERMAL HDT, 1,8 MPa ISO 75A C 102 TECHNICAL Melt Flow Rate (230 С; 2,16 kg) ISO 1133 g/10min 21 Moulding shrinkage, parallel ISO % 0,76 Moulding shrinkage, normal ISO % 0,11 PROCESSING Melt temperature range С Mould temperature 60 Drying temperature С - Drying time h - Comments: * drying is not necessary needed in case material is stored in dry warehouse Automotive Application

12 Material technical specification Polypropylene s compound Armlen PP GF 30-5HS-901 (black) 30% chemically coupled glass fiber filled polypropylene, heat stabilized, black colored, for structural part application (front-end). Properties Test Method Unit Value PHYSICAL-MECHANICAL Filler content ISO1172 % 30 Density ISO 1183 g/cm 3 1,15 Tensile Stress at Break ISO 527 MРa 85 Flexural modulus ISO 178 MPa 5600 Izod impact strength unnotched at 23 C, method А ISO 180/1eA kj/m 2 54 Izod impact strength unnotched at -45 C, method А ISO 180/1eA kj/m 2 50

13 THERMAL HDT, 1,80 MPa ISO 75A C 145 TECHNICAL Melt Flow Rate (230 С; 2,16 kg) ISO 1133 g/10min 6 Moulding shrinkage, parallel ISO % 0,3 Moulding shrinkage, normal ISO % 0,6 PROCESSING Melt temperature С 245 Mould temperature С 60 Drying temperature С 85 Drying time h 1-2 Comments: * drying is not necessary needed in case material is stored in dry warehouse Automotive Application

14 Material technical specification Polypropylene s compound Armlen PP MD 40-4HS-901 (black) 40% mineral filled polypropylene, heat stabilized, for under-the-hood application (e.g. the heater fan housing). Properties Test Method Unit Value PHYSICAL-MECHANICAL Filler content ISO1172 % 37 Density ISO 1183 g/cm 3 1,2 Tensile stress at yield ISO MPa 25 Tensile modulus ISO MPa 3200 Flexural modulus ISO 178 MPa 3100 Flexural strength ISO178 MPa 46 Charpy impact strength unnotched at 23 C ISO 179 kj/m 2 22

15 THERMAL Melt temperature ISO 3146 C Heat ageing 150 C/700h h No cracking HDT, 1,80 MPa ISO 75A C 85 TECHNICAL Melt Flow Rate (230 С; 2,16 kg) ISO 1133 g/10min 12 Moulding shrinkage % 0,9 PROCESSING Melt temperature С Mould temperature Drying temperature С Drying time h Comments: * drying is not necessary needed in case material is stored in dry warehouse Automotive Application

16 Material technical specification Armlen PP MF 20-2HS-901 (black) 20% mineral filled polypropylene, heat stabilized, black colored for HVAC application. Polypropylene s compound Properties Test Method Unit Value PHYSICAL-MECHANICAL Filler content ISO1172 % 21 Density ISO 1183 g/cm 3 1,06 Tensile strength ISO 527 MPa 27 Flexural modulus ISO 178 MPa 2350 Izod impact strength notched at 23 C, method А ISO 180/1eA kj/m 2 3,4 THERMAL HDT, 0,45 MPa ISO 75A C 125 HDT, 1,80 MPa ISO 75A C >80

17 TECHNICAL Melt Flow Rate (230 С; 2,16 kg) ISO 1133 g/10min 12 Moulding shrinkage, parallel ISO % 1,1 Moulding shrinkage, normal ISO % 1,1 PROCESSING Melt temperature С 235 Mould temperature 60 Drying temperature С - Drying time h - Comments: * drying is not necessary needed in case material is stored in dry warehouse Automotive Application

18 Material technical specification Armlen PP MF (black) 20% mineral filled polypropylene with low emission, heat stabilized, black colored. Customers choose this material for dashboard frame. Polypropylene s compound Properties Test Method Unit Value PHYSICAL-MECHANICAL Filler content ISO1172 % 21 Density ISO 1183 g/cm 3 1,06 Tensile stress at yield ISO MPa 33 Tensile modulus ISO 527 MPa 2700 Izod impact strength notched at 23 C, method А ISO 180/1eA kj/m 2 4,0 THERMAL HDT, 0,45 MPa ISO 75A C 125 HDT, 1,80 MPa ISO 75A C 80

19 TECHNICAL Melt Flow Rate (230 С; 2,16 kg) ISO 1133 g/10min 13 Moulding shrinkage, parallel ISO % 1,3 Moulding shrinkage, normal ISO % 1,3 PROCESSING Melt temperature С 235 Mould temperature 60 Drying temperature С - Drying time h - Comments: * drying is not necessary needed in case material is stored in dry warehouse Automotive Application

20 Material technical specification Polypropylene s compound Armlen PP MF (black) 20% mineral filled polypropylene, heat stabilized, black colored for automotive nonvisible application (e. g. air duct in the instrument panel). Properties Test Method Unit Value PHYSICAL-MECHANICAL Filler content ISO1172 % 22 Density ISO 1183 g/cm 3 1,07 Tensile stress at yield ISO MPa 33 Tensile modulus ISO 527 MPa 2700 Izod impact strength notched at 23 C, method А ISO 180/1eA kj/m 2 4,0 THERMAL HDT, 0,45 MPa ISO 75A C 125 HDT, 1,80 MPa ISO 75A C 80

21 TECHNICAL Melt Flow Rate (230 С; 2,16 kg) ISO 1133 g/10min 13 Moulding shrinkage, parallel ISO % 1,3 Moulding shrinkage, normal ISO % 1,3 PROCESSING Melt temperature С 235 Mould temperature 60 Drying temperature С - Drying time h - Comments: * drying is not necessary needed in case material is stored in dry warehouse Automotive Application

22 Material technical specification Polypropylene s compound Armlen PP-10IM-901 This grade is a mineral filled polypropylene compound for exterior application (painted bumpers). Properties Test Method Unit Value PHYSICAL-MECHANICAL Density ISO 1183 kg/m Yield stress ISO 527 MPa 19 Yield strain ISO 527 % 5,7 Strain at break ISO 527 % 200 Flexural modulus ISO 178 MPa 1550 Notched Izod Impact Strength at +23 C ISO 180/1A kj/m 2 40Р Notched Izod Impact Strength at -20 C ISO 180/1A kj/m 2 6,7

23 TECHNICAL Melt Flow Rate (230 C; 2,16 kg ) ISO 1133 g/10 min 22 Moulding shrinkage ISO % 0,5-0,6 PROCESSING Melt temperature range C Mold temperature C 60 Drying time, Dehumidified dryer C 2 Drying temperature C 80 Automotive Application

24 Material technical specification Polypropylene s compound Armlen PP MF 20-3IM Talc filled impact modified polypropylene composite material for interior trim application. Available in customer color. Typical application is instrument panel. Properties Test Method Unit Value PHYSICAL-MECHANICAL Density ISO 1183 g/cm 3 1,02 Tensile modulus ISO MPa 2000 Izod impact strength notched at 23 C ISO 180 kj/m 2 22 THERMAL HDT, 0,45 MPa ISO 75A C 110 HDT, 1,80 MPa ISO 75A C 68

25 TECHNICAL Melt Flow Rate (230 С; 2,16 kg) ISO 1133 g/10min 12 Moulding shrinkage, parallel ISO % 1,1 Moulding shrinkage, normal ISO % 1,1 PROCESSING Melt temperature range С Mould temperature 60 Comment: * drying is not necessary needed in case material is stored in dry warehouse Home Appliances Application

26 The mill produces a wide range of materials based on PP, PA, PBT and POM for molding different parts and components used in household appliances. Our feature is the production materials for heavy loaded parts, components of heating devices and etc. Armlen (a material based on PP) combines ease of processing with a fairly high mechanical strength and high resistance in a variety of environments, including in solutions of detergents, household goods, acids and alkalis. Competitive prices make Armlen absolute leader in the market of thermoplastic materials for Major Domestic Appliances. Armamid (based on PA 6) and Technamid (based on PA 6,6) are used for most heavy-duty parts, such as gears, idlers, rollers, etc. Technoter (based on PBT) is generally used where there is a need to maintain an excellent appearance when exposed to high temperatures. All materials are available in three versions: glass-reinforced, mineral-filled and flame-retardant and also in combination.

27 Home Appliances Application 02 HOME APPLIANCES APPLICATION

28 Material technical specification Polypropylene s compound Armlen PP GF MF 30-1 This grade is a 30% glass and mineral filled polypropylene homopolymer. The product is designed for injection molding of washing machine parts. Benefits gained from this gevelopment: - resistance to alternating load, - low production costs, - good dimensional stability, - easy processing. Material was tested in water solution of «Ariel» washing powder at 90 C for 1-20 days with slight changing in mechanical properties. Material was checked for thermostability according to ASTM D3012 Color change (Disk 50*3 mm): - after exposition at 150 C, 850 hrs - no yellowness, - after exposition in the oven at 90 C,20 days, then 750 hrs at 150 C no destruction.

29 Properties Test Method Unit Value PHYSICAL-MECHANICAL Density ISO 1183 kg/m Ash content ISO 3451 % 30 Stress at brake ISO 527 MPa 69 Flexural modulus ISO 178 MPa 3640 Flexural strength ISO 178 MPa 85 Unnotched Charpy impact strength at +23 C ISO 179/leU kj/m 2 41 Notched Charpy impact strength at +23 C ISO 179/leA kj/m 2 12 TECHNICAL Melt Flow Rate (230 C; 2,16 kg ) ISO 1133 g/10 min 3,5 Moulding shrinkage, parallel ISO % 0,7-0,8 Moulding shrinkage, normal ISO % 0,7-0,8 THERMAL HDT, 0,45 MPa ISO 75/B C 156 PROCESSING Melt temperature range C Mold temperature C 60 Home Appliances Application

30 Material technical specification Polypropylene s compound Armlen PP MF 40-2HS This grade is a 40% mineral filled (CaCO 3 ) polypropylene homopolymer, impact modified. The product is designed for injection molding of washing machine parts and is available in natural color. Benefits gained from this development: - Low production costs - Good surface - Good dimensional stability - Comply with European safety requirements and internal company s standards Material was tested in water solution of «Ariel» washing powder at 90 C for 1-20 days with slight changing in mechanical properties. Material was checked for thermostability according to ASTM D3012 Color change (Disk 50*3 mm): - after exposition at 150 C, 850 hrs - no yellowness - after exposition in the oven at 90 C,20 days, then 750 hrs at 150 C - no destruction. Properties Test Method Unit Value PHYSICAL-MECHANICAL Density ISO 1183 kg/m Ash content ISO 3451 % 40 Stress at break ISO 527 MPa 20

31 Strain at break ISO 527 % 50 Flexural modulus ISO 178 MPa 2150 Flexural strength ISO 178 MPa 30 Unnotched Charpy impact strength at +23 C ISO 179/leU kj/m 2 NB Unnotched Charpy impact strength at -40 C ISO 179/leU kj/m 2 14 Notched Charpy impact strength at +23 C ISO 179/leA kj/m 2 3,5 TECHNICAL Melt Flow Rate (230 C; 2,16 kg) ISO 1133 g/10 min 14 Moulding shrinkage, parallel ISO % 1,1-1,4 Moulding shrinkage, normal ISO % 0,8-1,2 THERMAL HDT, 0,45 MPa ISO 75/B C 95 Vicat Softening Temperature, 50N ISO 306/B C 100 PROCESSING Melt temperature range C Mold temperature C 60 Home Appliances Application

32 Material technical specification Polypropylene s compound Armlen PP MF 40-3M This grade is a 40% mineral filled (CaCO 3 ) polypropylene copopolymer PP. The product is designed for injection molding of refrigirator boxes parts and is available in a few tints of white color. Material has high impact resistance at low temperatures. Benefits Gained from this Development: - Low production costs - Good surface - Good dimensional stability - Comply with European safety requirements and internal company s standards. Fridge box from Armlen PP MF 40-3M. Properties Test Method Unit Value PHYSICAL-MECHANICAL Density ISO 1183 kg/m Ash content ISO 3451 % 40 Strain at break ISO 527 MPa 20 Yield strain ISO 527 % 4 Flexural modulus ISO 178 MPa 2100

33 Flexural strength ISO 178 MPa 25 Notched Charpy impact strength at +23 C ISO 179/leA kj/m 2 3,5 Unnotched Charpy impact strength at -30 C ISO 179/leU kj/m 2 20 THERMAL Melt Flow Rate (230 C; 2,16 kg) ISO 1133 g/10 min 16 Moulding shrinkage, parallel ISO % 0,9-1,2 Moulding shrinkage, normal ISO % 0,9-1,2 THERMAL HDT, 0,45 MPa ISO 75/B C 100 CLTE ISO E-5 K-1 6 PROCESSING Melt temperature range C Mold temperature C 60 Comments: * after exposition at 150 C, 850 hrs - no yellowness; * after exposition in the oven at 90 C,20 days, then 750 hrs at 150 C- no destruction. Home Appliances Application

34 Armoflen PO MF is the trade name of a range of CaCO 3 masterbatches based on various types of polyolefin. These products are widely used in such applications as blown films, cast films, sheets, bending tapes, wicker ropes, heavy duty bags, pipes and profile extrusions and injection molding. The main benefits of such materials are follows: cost saving, productivity increase, easier printing, higher stiffness (also annular stiffness for pipes) and decreased cooling time. Additional advantage of using CaCO 3 as filler is that the material is non-toxic natural mineral and can be used for food contact applications. Currently we produce Armoflen grades with a CaCO 3 content from 65 to 80%. We offer grades based on different polymer matrices, such as HDPE, LLDPE, PP- homo and PP-copo, and with MFI of the compositions from 1 to 70 g/10 min. Also, we re able to produce tailor-made grades with required properties e.g. flowability, polymer types, particle size and with special additives including PPA.

35 CaCO 3 and Talc MB 03 CACO 3 AND TALC MB APPLICATION

36 Material technical specification Armoflen PO MF CaCO 3 masterbatches produced with filling ratio: 60, 65, 70, 75, 80%. LLDPE, HDPE, LDPE, PP compound GRADE ARMOFLEN PO MF 65-1 ARMOFLEN PO MF 65-2 ARMOFLEN PO MF 65-3 ARMOFLEN PO MF 65-4 ARMOFLEN PO MF 75-1 ARMOFLEN PO MF 75-2 POLYMER BASE/% MASS CONTENT LLDPE/35 LLDPE/35 PE/35 PP/35 PPHOMO/75 LLDPE/75 СACO 3,% mass content 65 65* 65** Average particles size, μm 1,5 1,5 1,5 1,2 2,5 2,5 Melt Flow Rate, (190 С, 5,0 kg), 3,0-5,0 3,0-5,0 1,2-2, Density, g/cm 3 1,64-1,65 1,64-1,65 1,64-1,65 1,64-1,65 1,82-1,84 1,82-1,86 Water content at package, %, less than 0,10% 0,10% 0,10% 0,10% 0,10% 0,10%

37 Application, Dosage Blown films Up to 35% Up to 35% Up to 35% Up to 35% Cast films and sheets Up to 35% Up to 35% Up to 50% Up to 30% Up to 30% PP Fibers Up to 20% Bending tapes and wicker ropes Up to 15% Up to 15% Heavy duty bags Up to 30% Up to 30% Pipes and profiles Up to 25% Up to 25% Injection molding Up to 25% Up to 25% Comments: * with fluorocarbon PPA ** filler composition 50% CaCO 3 /15% TiO 2 CaCO 3 and Talc MB

38 Our material portfolio includes grades for civil construction application. The material Armlen PE MF 70-2FR was developed based on magnesium hydroxide and polyethylene and it is used for aluminum composite panels (middle layer). The combustion specific heat of this material is less than 10 MJ/kg. Armlen PP MF 30-3IM and Armlen PP MF 40-4M are grades which were specially developed for basement siding with a different structure (imitation brick, imitation natural stone etc.). Distinctive features of these grades are high UV stability and impact strength. There are also grades for PP pipe reinforcement which are used for central heating systems, central hot water supply systems and industrial pipe systems. The use of Armlen PP GF 20-1EX and Armlen PP GF 30-1EX in a pipe middle layer allows necessary pipe strength with a lower wall thickness as well as throughput capacity increase.

39 Construction Application 04 CONSTRUCTION APPLICATION

40 Material technical specification Polypropylene s compound Armlen PP MF 40-4M This grade is a 40% mineral filled (СаСОз) polypropylene copopolymer PP. The product is designed for exterior application. Material has high impact resistance at low temperatures. Benefits Gained from this Development: - Low production costs - Good surface - Good dimensional stability - Comply with European safety requirements and internal company s standards. Properties Test Method Unit Value PHYSICAL-MECHANICAL Density ISO 1183 kg/m Ash content ISO 3451 % 40 Strain at break ISO 527 MPa 20 Yield strain ISO 527 % 4 Flexural modulus ISO 178 MPa 2100

41 Flexural strength ISO 178 MPa 25 Notched Charpy impact strength at +23 C ISO 179/leA kj/m 2 3,5 Unnotched Charpy impact strength at -30 C ISO 179/leU kj/m 2 20 TECHNICAL Melt Flow Rate (230 C; 2,16 kg ) ISO 1133 g/10 min 16 Moulding shrinkage, parallel ISO % 0,9-1,2 Moulding shrinkage, normal ISO % 0,9-1,2 THERMAL HDT, 0,45 MPa ISO 75/B C 100 CLTE ISO E-5 K-1 6 PROCESSING Melt temperature range C Mold temperature C 60 Comments: * after exposition at 150 C, 850 hrs - no yellowness; * after exposition in the oven at 90 C,20 days, then 750 hrs at 150 C - no destruction. Construction Application

42 Material technical specification Polypropylene s compound Armlen PE MF 70-2FR 70% magnesium hydroxide Mg(OH) 2 filled polyethylen. The product is designed for extrusion of fire-resistant aluminum composite panels. Flammability is class B,s1,d0 acc.en Key advantages: - easy processing, - high fire-resistance, - exelent adhesion to alluminium foil paper. Aluminium composite panels, middle layer from Armlen PE MF 70-2FR. Properties Test Method Unit Value PHYSICAL-MECHANICAL Density ISO 1183 kg/m Melt Flow Rate (190 C; 5 kg) ISO 1133 g/10 min 2,4

43 Stress at break ISO 527 MPa 11 Flexural modulus ISO 178 MPa 650 PROCESSING Melt temperature range C Construction Application

44 Material technical specification Polypropylene s compound Armlen PP MF 30-3IM This grade is a 30% mineral filled polypropylene for exterior application. Key advantages: - UV - resistance, - good dimensional stability, - heat stabilized, - impact modified, - easy processing, - resistance to atmospheric precipitates. Socle siding from Armlen PP MF 30-3IM. Properties Test Method Unit Value PHYSICAL-MECHANICAL Density ISO 1183 kg/m Tensile strength ISO 527 MPa 18 Strain at break ISO 527 % 15 Unnotched Charpy impact strength at +23 C ISO 179/leU kj/m 2 60

45 TECHNICAL Melt Flow Rate (230 C; 2,16 kg) ISO 1133 g/10 min Moulding shrinkage, parallel ISO % 0,7-1,0 Moulding shrinkage, normal ISO % 0,7-1,0 PROCESSING Melt temperature range C Mold temperature C 60 Construction Application

46 Material technical specification Polypropylene s compound Armlen PP GF 20-1EX 20% glass-filled random polypropylene copolymer. Engineering application: - Middle layer glass-fibre reinforced pipes (PP-R/PP-R+GF/PP-R) Properties Test Method Unit Value PHYSICAL Density ISO 1183 kg/m Tensile Stress (Yield) ISO 5272 MPa 52 Tensile Strain (Break) ISO 527 % 7,5 Bending stress at maximum load ISO 178 MPa 75 Flexural Modulus ISO 178 MPa 3200 Charpy Unnotched Impact Strength at 68 F ISO 179/1eU kj/m 2 65 Charpy Unnotched Impact Strength at - 40 F ISO 179/1eU kj/m 2 50 Charpy Notched Impact Strength at 68 F ISO 179/1eU kj/m 2 22 Charpy Notched Impact Strength at - 40 F ISO 179/1eU kj/m 2 10

47 THERMAL Melt temperature ISO 3146 F ( С) 293 (145) HDT, 1,8 MPa ISO 75 F ( С) 234 (112) CLTE ISO E-5 K-1 2,9 TECHNICAL Melt Flow Rate (230 C; 2,16 kg) ISO 1133 g/10 min 0,5-1,0 Moulding shrinkage, parallel ISO % 0,3-0,4* Moulding shrinkage, normal ISO % 0,6-0,8* Comments: * shrinkage measured on the sample type 7 (plate 60*60*2mm) ** drying is not required, if the material is stored in a dry warehouse Construction Application

48 Material technical specification Polypropylene s compound Armlen PP GF 30-1EX 30% glass-filled statistical polypropylene copolymer. Properties Test Method Unit Value PHYSICAL-MECHANICAL Density ISO 1183 kg/m Tensile Stress (Yield) ISO 5272 MPa 64 Tensile Strain (Break) ISO 527 % 7,4 Bending stress at maximum load ISO 178 MPa 104 Flexural Modulus ISO 178 MPa 5300 Charpy Unnotched Impact Strength at 68 F ISO 179/1eU kj/m 2 70 Charpy Unnotched Impact Strength at -40 F ISO 179/1eU kj/m 2 55 Charpy Notched Impact Strength at 68 F ISO 179/1eU kj/m 2 21 Charpy Notched Impact Strength at -40 F ISO 179/1eU kj/m 2 9

49 THERMAL Melt temperature ISO 3146 F ( C) 298 (148) HDT, 1,8 MPa ISO 75 F ( C) 250 (121) CLTE ISO E-5 K-1 2,6 TECHNICAL Melt Flow Rate (230 C; 2,16 kg) ISO 1133 g/10 min 0,5-1,0 Moulding shrinkage, parallel ISO % 0,3-0,4* Moulding shrinkage, normal ISO % 0,6-0,8* Comments: * shrinkage measured on the sample type 7 (plate 60*60*2mm) ** drying is not required, if the material is stored in a dry warehouse Construction Application

50 Steel pipe anticorrosive coatings play one the most important role in pipeline protection, reliability and safety operation for the whole life cycle. High density polyethylene Torlen and adhesive compound Armobond are developed for three layer PE steel pipe coating production and fit general requirements of JSC «Transneft» and OAO Gazprom applied to major steel pipelines. Torlen and Armobond application provides technological production efficiency, high mechanical protection properties, stable adhesion level and resistance to the most important aging factors: temperature, UV and corrosion aggressive media.

51 Steel pipe coating 04.1 STEEL PIPE COATING

52 Material technical specification HDPE carbon filled compound Torlen PE-2K-901 Black carbon filled high density polyethylene UV and termostabilized compound with improved processing properties for top-coat in two or three-layer PE steel pipe coating. Material is designed to be applied with Armobond adhesive for maximum protection and operating properties. Properties Test method Unit Value PHYSICAL-MECHANICAL Density ISO 1183 g/cm 3 0,942 0,952 Yield strength ASTM D 638 MPa > 18 Tensile stress at break ASTM D 638 MPa > 22 Elongation at break ASTM D 638 % > 600 Hardness ASTM D 2240 Shore D > 60 Carbon Black content ASTM D 1603 % 2,0 2,5

53 THERMAL Melt Flow Rate (190 C; 2,16 kg) ISO 1133 g/10min 0,3 0,6 Melt Flow Rate (190 C; 5 kg) ISO 1133 g/10min 1,5 2,2 Vicat Softening Temperature, 10N ISO 306 C >115 Melt temperature ISO 3146 C Brittleness Temperature ASTM D 746 C < -70 Steel pipe coating

54 Material technical specification PE adhesive compound Armobond PE-2K PE based adhesive compound with improved processing properties and stable high level adhesion to epoxy resin for three-layer PE steel pipe coating. Material is designed to be applied with Torlen top-coat material for maximum protection and operating properties. Properties Test method Unit Value PHYSICAL-MECHANICAL 0,910 Density ISO 1183 g/cm 3 0,930 Yield strength ASTM D 638 MPa > 10 Tensile stress at break ASTM D 638 MPa > 15 Elongation at break ASTM D 638 % > 500 Hardness ASTM D 2240 Shore D > 45

55 THERMAL Melt Flow Rate (190 C; 2,16 kg) ISO 1133 g/10min 1,0 3,0 Vicat Softening Temperature, 10N ISO 306 C > 95 Melt temperature ISO 3146 C > 115 Brittleness Temperature ASTM D 746 C < -70 OPERATION (TYPICAL) Adhesion level GOST R N/cm > 300 Steel pipe coating

56 We have developed the materials Technotep A and Technotep B based on SBS and SEBS for extrusion and injection applications. These materials have properties close to rubber but they can be processed by extrusion or injection molding and recycled as thermoplastics. Technotep A materials have high tensile strength, elongation and low set. Technotep B materials have increased thermal stability and resistance to ozone, oxygen and UV. Thanks to these properties goods made of Technotep B have increased service life. Technotep A and Technotep B materials retain their properties over a wide temperature range from -60 to 110 degrees. Standard grades have a hardness range of 60 to 90 (Shore A scale) and can be used for such applications as window profile sealings, car mats and shoe soles.

57 TPE 05 TPE APPLICATION

58 Material technical specification SBS Compounds TechnoTep A 65A Standard thermoplastic elastomer, low mineral filled, good flexibility. Properties Test Method Unit Value PHYSICAL-MECHANICAL Hardness ISO 868 Shore A 65 Density ISO 1183 g/cm 3 1,00 Melt Flow Rate (190 C; 5 kg) ISO 1133 g/10 min 40 ELASTOMERS Tensile strenght ISO 37 MPa 4,7 Elongation at break ISO 37 % 600 Abrasion DIN mm 3 230

59 PROCESSING Melt temperature range С Mould temperature range С TPE

60 Material technical specification SBS Compounds TechnoTep B 45D Standard thermoplastic elastomer, high mineral filled, weather stability. Properties Test Method Unit Value PHYSICAL-MECHANICAL Hardness ISO 868 Shore D 45 Density ISO 1183 g/cm 3 1,13 Melt Flow Rate (190 C; 5 kg) ISO 1133 g/10 min 3,5 Brittleness Point С -55 ELASTOMERS Tensile strenght ISO 37 MPa 14 Elongation at break ISO 37 % 450

61 THERMAL Max. Dynamic Service Temperature С 90 Max. Static Service Temperature С 135 PROCESSING Melt temperature range С Mould temperature range С TPE

62 Material technical specification SEBS compound TechnoTep B 60A Standard thermoplastic elastomer, medium mineral filled, weather stability. Properties Test Method Unit Value PHYSICAL-MECHANICAL Hardness ISO 868 Shore A 60 Density ISO 1183 g/cm 3 1,08 Melt Flow Rate (190 C; 5 kg) ISO 1133 g/10 min 3,5 Brittleness Point С -55 ELASTOMERS Tensile strenght ISO 37 MPa 6,5 Elongation at break ISO 37 % 650 Compression set (22h/70 o C) ASTM D 395 % 40

63 THERMAL Max. Dynamic Service Temperature С 90 Max. Static Service Temperature С 135 PROCESSING Melt temperature range С Mould temperature range С TPE

64 Material technical specification SEBS compound TechnoTep B 65A Standard thermoplastic elastomer, high mineral filled, weather stability. Properties Test Method Unit Value PHYSICAL-MECHANICAL Hardness ISO 868 Shore A 65 Density ISO 1183 g/cm 3 1,20 Melt Flow Rate (190 C; 5 kg) ISO 1133 g/10 min 3,5 Britlleness Point С -55 ELASTOMERS Tensile strenght ISO 37 MPa 5,5 Elongation at break ISO 37 % 750 Compression set (22h/70 C) ASTM D 395 % 50

65 THERMAL Max. Dynamic Service Temperature С 90 Max. Static Service Temperature С 135 PROCESSING Melt temperature range С Mould temperature range С TPE

66 For electrical and electronics applications we have developed composite materials based on PP, PA6, PA66 and PBT matrix. Below you can find information about grades based on PP and PA6. The main applications for these grades are wiring accessories, power distribution equipment, lighting and heating appliances and electrical switch equipment. Depending on final application there are materials with a different class of flame retardancy. Materials are certified according the UL and in line with RoHS requirements as the European Directive.

67 06 ELECTRICAL AND ELECTRONICS APPLICATION E&E Application

68 Material technical specification Polyamide 6 compound Armamid PA GF25-1FR Polyamide 6 glass reinforced (25%) flame retardant (V-0 at 1,6 mm), RoHS compliant, high CTI. Properties Test Method Unit Value PHYSICAL-MECHANICAL Density ISO 1183 kg/m Stress at break ISO 527 MPa 130 Strain at break ISO 527 % 3 Flexural stress at max. load ISO 178 MPa 180 Flexural modulus ISO 178 MPa 8000 Unnotched Charpy impact strength at +23 C ISO 179/1eU kj/m 2 40 THERMAL Melting point ISO C 220 HDT, 1,8 MPa ISO 75 C 195

69 ELECTRICAL Electric strength IEC kv/mm 25 Volume resistivity IEC Ohm*m 10Е13 CTI IEC Volts 350 FLAMMABILITY Burning behavior (at 1,6 mm thickness) UL94 V-0 Glow wire flammability index (1,6 mm) IEC С 960 TECHNICAL Moulding shrinkage, parallel ISO % 0,15-0,25* Moulding shrinkage, normal ISO % 0,6-0,9* PROCESSING Melt temperature range С Mold temperature С 90 Drying temperature С 85 Drying time hours 2-4 Processing moisture content % 0,1-0,2 Comments: * molding shrinkage data are indicative only; it is recommended for mold designers to know about the mold shrinkage dependence on molding parameters, the article shape, dimensions as well as the runners design and geometry. E&E Application

70 Material technical specification Polyamide 6 compound Armamid PA GF 50-1 Polyamide 6 glass reinforced (50%) Characterized by high stiffness (Tensile modulus MPa, flexural modulus MPa). Properties Test Method Unit Value PHYSICAL-MECHANICAL Density ISO 1183 kg/m Stress at break ISO 527 MPa 190 Strain at break ISO 527 % 3 Flexural stress at max. load ISO 178 MPa 290 Flexural modulus ISO 178 MPa Unnotched Charpy impact strength at +23 C ISO 179/1eU kj/m 2 75 Unnotched Charpy impact strength at -40 C ISO 179/1eU kj/m 2 65 Notched Charpy impact strength at +20 C ISO 179/1eA kj/m 2 12 Notched Charpy impact strength at - 40 C ISO 179/1eA kj/m 2 9

71 THERMAL Melting point ISO C 220 HDT, 0,45 MPa ISO 75 C 215 HDT, 1,8 MPa ISO 75 C 205 Coefficient of linear thermal expansion (parallel) ISO /-2 1E-5 К -1 2,5 Water absorption (immersion 23 C, 24 hours) ISO 62 % 0,95 FLAMMABILITY Glow wire flammability index (1,6 mm) IEC С 650 TECHNICAL Moulding shrinkage, parallel ISO % 0,1-0,2* Moulding shrinkage, normal ISO % 0,6-0,8* PROCESSING Melt temperature range C Mold temperature C 80 Drying temperature C 85 Drying time hours 2-4 Processing moisture content % 0,1-0,2 Comments: * molding shrinkage data are indicative only; it is recommended for mold designers to know about the mold shrinkage dependence on molding parameters, the article shape, dimensions as well as the runners design and geometry. E&E Application

72 Material technical specification Polyamide 6 compound Armamid PA 6-1FR Polyamide 6 flame retardant (halogen and phosphor free). Properties Test Method Unit Value PHYSICAL-MECHANICAL Density ISO 1183 kg/m Stress at break ISO 527 MPa 80 Strain at break ISO 527 % 10 Flexural stress at max. load ISO 178 MPa 105 Flexural modulus ISO 178 MPa 3000 Unnotched Charpy impact strength at +23 C ISO 179/1eU kj/m 2 not break Notched Charpy impact strength at +23 C ISO 179/1eA kj/m 2 8 THERMAL Melting point ISO C 220 HDT, 0,45 MPa ISO 75 C 185 HDT, 1,8 MPa ISO 75 C 75

73 ELECTRICAL Electric strength IEC kv/mm 25 Volume resistivity IEC Ohm*m 10E13 CTI IEC Volts 600 FLAMMABILITY Burning behavior (at 1,6 mm thickness) UL94 V-2 Glow wire flammability index (1,6 mm) IEC С 960 TECHNICAL Moulding shrinkage, parallel ISO % 0,9-1,2* Moulding shrinkage, normal ISO % 0,9-1,2* PROCESSING Melt temperature range С Mold temperature С 80 Drying temperature С 85 Drying time hours 2-4 Processing moisture content % 0,1-0,2 Comments: * molding shrinkage data are indicative only; it is recommended for mold designers to know about the mold shrinkage dependence on molding parameters, the article shape, dimensions as well as the runners design and geometry. E&E Application

74 Material technical specification Polypropylene s compound Armlen PP MF 15-3 FR Mineral filled PP homopolymer, flame retardant, RoHS compliant. Properties Test Method Unit Value PHYSICAL-MECHANICAL Density ISO 1183 kg/m Yield stress ISO 527 MPa 20 Strain at break ISO 527 % 25 Flexural modulus ISO 178 MPa 2000 Unnotched Charpy impact strength at +23 C ISO 179/1eU kj/m 2 62 Unnotched Charpy impact strength at - 40 C ISO 179/1eU kj/m 2 15 THERMAL Melting point ISO C 160 HDT, 0,45 MPa ISO 75 C 107

75 TECHNICAL Linear mould shrinkage paralled ISO 294 % 0,7-0,9* Linear mould shrinkage normal ISO 294 % 0,9-1,1* FLAMMABILITY Burning behavior (at 1,6 mm thickness) UL94 V-0 Glow wire flammability index (1,6 mm) IEC С 960 CTI IEC Volts 500 PROCESSING Melt temperature С 220 Mould temperature range С Comments: * specimen type 7, plate 60*60*2 mm E&E Application

76 Material technical specification Polypropylene s compound Armlen PP-2FR Flame retardant polypropylene, RoHS compliant. Properties Test Method Unit Value PHYSICAL-MECHANICAL Density ISO 1183 kg/m Yield stress ISO 527 MPa 34 Strain at break ISO 527 % 43 Flexural modulus ISO 178 MPa 1600 Flexural stress at max. load ISO 178 MPa 30 Unnotched Charpy impact strength at +23 C ISO 179/1eU kj/m 2 70 Unnotched Charpy impact strength at -40 C ISO 179/1eU kj/m 2 15 THERMAL Melting point ISO C 160

77 FLAMMABILITY Glow wire flammability index (1,6 mm) IEC С 960 Burning behavior (at 1,6 mm thickness) UL94 V-2 CTI IEC Volts 550 TECHNICAL Moulding shrinkage, parallel ISO % 1,1-1,3 * Moulding shrinkage, normal ISO % 1,1-1,3 * PROCESSING Mold temperature range С Melt temperature С 220 Drying temperature С 80 ** Drying time hours 2 ** Comments: * specimen type 7, plate 60*60*2 mm ** drying is not necessary if the material kept in dry stock E&E Application