10.6 Schedule of Accreditation

Transcription

1 Testing Laboratory is accredited by the GCC Accreditation Center () in accordance with the recognized International Standard, General requirements for the competence of testing and calibration laboratories SGS Hong Kong Limited Issue No: 2 Issue Date: 30 May /F, 3/F, 4/F & 5/F, On Wui Centre, 25 Lok Yip Road, On Lok Tsuen, Fanling, New Territories, Hong Kong Contact: Frederick Cheung Phone: Fax: Frederick.cheung@sgs.com Website: Locations where certification activities covered by the above Accreditation Standard are undertaken SGS Hong Kong Limited Laboratory. 1/F, 3/F, 4/F & 5/F, On Wui Centre, 25 Lok Yip Road, On Lok Tsuen, Fanling, N.T. Hong Kong Version: 2 Page 1 of 5

2 For the following scope: 03. Performance and Approvals Testing 07. Chemical Testing 13. Mechanical Testing 50. GSO Directives Scope details are as follows: Test Category Items, Materials or Products Tested Specific Tests or Properties Measured Specification, Standard Method or Technique Used - EN 71-2: A1: ISO :2014 Flammability Physical and mechanical <Excluding.> Tests for flammable gases, extremely flammable liquids, highly flammable liquids, flammable liquids and flammable gels - EN 71-1:2014 o 4.11 Mouth-actuated toys and other toys intended to be put in the mouth o Strength o Braking o Transmission and wheel arrangement o Toy bicycles o Toy scooters Version: 2 Page 2 of 5

3 - ISO :2014 o Overload requirements for ride-on toys and seats o Mouth-actuated projectile toys o 4.21 Braking o Braking requirements o 4.26c Mouth-actuated toys o 4.29 Toy scooters o Mouth-Actuated o Battery-Powered Ride-On o 4.29 Art Materials o 8.20 Dynamic Strength Test for Wheeled Ride-on Electric toys Electrical - EN 62115: A12:2015 <Excluding > o 11.1 (IP test to IEC60529) o Clause 14.15, o 16.1 (component tests to other standards) o 19.2 (burning test to other standards) o 20 o Annexes C and E, ZB and ZC (test to EN 62233) o o (Mobile toys intended to be used in water) o Battery-Powered Ride-On Version: 2 Page 3 of 5

4 - EN 71-3: A1:2014 a) Category I, II, III Aluminium(Al), Antimony(Sb), Arsenic(As), Barium(Ba), Boron(B), Cadmium(Cd), Chromium(Cr), Cobalt(Co), Copper(Cu), Lead(Pb), Manganese(Mn), Mercury(Hg), Nickel(Ni), Selenium(Se), Strontium(St), Tin(Sn) and Zinc(Zn) b) Category I, III Organic tin (Methyl tin, Butyltin, Dibutyl tin, Tributyl tin, Tetrabutyl tin, n-octy tin, Di-n-octyl tin, Di-n-propyl tin, Diphenyl tin, Triphenyl tin) Chemical Properties c) Category I, III Chromium (VI), Chromium (III) (by calculation) - ISO8124-3: 2010 Amd.1:2014 Lead(Pb), Antimony(Sb), Chromium(Cr), Mercury(Hg), Arsenic(As), Barium(Ba), Selenium(Se), Cadmium(Cd), - ASTM F Lead(Pb), Antimony(Sb), Chromium(Cr), Mercury(Hg), Arsenic(As), Barium(Ba), Selenium(Se), Cadmium(Cd), - EN 71-9:2005+A1:2007: - EN71-10: EN71-11: 2005 <Excluding A.3 of Annex A > and childcare articles Phthalates CPSC-CH-C Analysis of DBP;BBP;DEHP;DINP;DIDP; DNOP Version: 2 Page 4 of 5

5 END SGS Hong Kong Limited, is recorded as issuing accredited certificates to organizations in the countries listed below. This list is current at the time of issue of this schedule. United Arab Emirates Bahrain Saudi Arabia Oman Qatar Kuwait Yemen Version: 2 Page 5 of 5