About Us. We had the good capability and capacity to meet most demands of the aluminum sheet and coil market and welcome your inquiry!

Size: px
Start display at page:

Download "About Us. We had the good capability and capacity to meet most demands of the aluminum sheet and coil market and welcome your inquiry!"

Transcription

1 About Us Henan Minmetals East Industrial Co., Ltd is a group company, and as one of the most important division of the company, Aluminum Products Division mainly dedicated to manufacture and supply best products in the flat rolled aluminum industry. Through the strategic cooperation with local factories, our aim is to provide high quality, in-time service at competitive pricing. The factory has advanced hot rolling lines, cold rolling lines and sheet lines. Our facilities include 18 casting and rolling mills line, 9 sets of 30t smelting furnaces, 18 sets of 20t heat preservation furnaces, one set of high-end cold rolling mills, one set of stretch straightening machines and six sets of 50t return equipment, as well as strict and standard quality control process & machines. We had the good capability and capacity to meet most demands of the aluminum sheet and coil market and welcome your inquiry! 1

2 Standard Specification The products from Minmetals East will be strictly produced according to national or international standard, or sometimes to mutually agreed standard. American Standard ASTM B209 ASTM B928 ANSI 35.1 ANSI 35.2 European Standard EN 573 EN 485 EN 546 Standard Specification for Aluminum and Aluminum Alloys Sheet and Plate Standard Specification for High Magnesium Aluminum-Alloy Sheet and Plate for Marine Service Alloy and Temper Designation System for Aluminum Dimensional Tolerances for Aluminum Mill Products Aluminum and Aluminum Alloys Chemical Composition and Form of Wrought Products Aluminum and Aluminum Alloys Sheets, Strip and Plate Aluminum and Aluminum Alloys Foil Alloy Designations Alloy Series American Standard European Standard 1xxx Series 3xxx Series 8xxx Series EN AW-1050A EN AW EN AW EN AW EN AW EN AW EN AW-3105 EN AW-8011A EN AW

3 TEMPER DESIGNATIONS Temper Definition F D H12 H14 H18 H19 H111 H112 H116 H22 H24 H26 H28 H32 H34 H36 H38 H321 H42 H44 H46 H48 H351 T4 T451 T6 T651 As fabricated (no mechanical property limits specified) Annealed Stain Hardened, 1/4 Hard Stain Hardened, 1/2 Hard Stain Hardened, 3/4 Hard Stain Hardened, Full Hard Stain Hardened, Extra Hard Annealed and slightly strain hardened (less than H11) Slightly strain harden from working at an elevated temperature or from limited amount of cold work Applies to alloys in the 5xxx series with a magnesium content of 3% or more, slightly strain harden at last operation, exfoliation and intergranular corrosion resistance are specified. Stain Hardened and Partially Annealed, 1/4 Hard Stain Hardened and Partially Annealed, 1/2 Hard Stain Hardened and Partially Annealed, 3/4 Hard Stain Hardened and Partially Annealed, Full Hard Stain Hardened and stabilized, 1/4 Hard Stain Hardened and stabilized, 1/2 Hard Stain Hardened and stabilized, 3/4 Hard Stain Hardened and stabilized, Full Hard Applies to alloys in the 5xxx series with a magnesium content of 3% or more, strain hardened and stabilized at last operation, exfoliation and intergranular corrosion resistance are specified. Stain Hardened and painted or lacquered, 1/4 Hard Stain Hardened and painted or lacquered, 1/2 Hard Stain Hardened and painted or lacquered, 3/4 Hard Stain Hardened and painted or lacquered, Full Hard Solution heat-treated, cold worked, stress relived by stretching, and naturally aged Solution heat-treated and naturally aged Solution heat-treated, stress relived by stretching, and naturally aged Solution heat-treated and then artificially aged Solution heat-treated, stress relived by stretching, and artificially aged 3

4 Chemical Composition Chemical Composition conforms to the standard specification of EN 573 and ASTM B209 others Alloy Si Fe Cu Mn Mg Cr Zn Ti eac Ai(Min) total h remaind er remaind er remaind er remaind er 4

5 Main Products Aluminum and Aluminum Alloy Strip and Coil Standard Specification: ASTM B209, EN 485 Alloy and Temper: Alloy Temper 1xxx: 1050, 1060, 1070,1100 3xxx: 3003, 3102 Available size range: Dimension Thickness: Width: O, F, H12, H14, H16, H18,H22, H24, H26 Range 0.15mm-8mm 200mm-1600mm Surface finish standard width: Mill Finish, Bright Finish, unless otherwise specified Surface protection: Without paper interleaved for all aluminum coils 5

6 Aluminum and Aluminum Alloy Sheet and Plate Standard Specification: ASTM B209, ATSM B928, EN 485 Alloy and Temper: Alloy Temper 1xxx: 1050, 1050A, 1060, 1100 O, H112, H12, H14, H16, H18, H22, H24, H26 3xxx: 3003, 3102 Available size range: Dimension Thickness: Width: Range 0.15mm-8mm 600mm-1650mm Surface finish standard width: Mill Finish, Bright Finish, unless otherwise specified Surface protection: Paper interleaved 6

7 1070 Aluminum roll for re-melting and extrusion Dimension Thickness: Width: Range 6mm-8mm 900mm-1600mm Advantage: *Such coil is specially designed to replace aluminum ingot, due to the high export tax of aluminum ingot, the coil has better price than ingot. *This type of coil can fit customer's re-melting furnace just like ingot, no need to make any change to the production line that was previously used for ingot. The standard coil size and weight is very suitable for the feed gate of furnace. *This type of coil causes less material wastage than ingot when re-melted. *Our coil is made directly from ore, no need to go through the ingot making process, quality is much better than other suppliers who use ingot scrap to make coil. New products development plan in near future: 1060ps PS and CTP plate stock Aluminum Alloy Tread Sheet Aluminum foil of 8011&3003 for container 7

8 Packaging EYE TO SKY Coil Weight: MT/ 6,613-11,023 LBS To be recommended when the coil width is over 1200mm (47.25 ) to maximize container loading and coil weight to be about 3 MT (6,613 LBS). 3 MT (6,613 LBS) EYE TO SIDE Coil Weight: MT/ 4,409-13,227 LBS To be recommended when the coil width is less than 1200mm (47.25 ) to maximize container loading WOODEN PALLET Pallet Weight: MT/ ,613 LBS Pallet weight of 2.0 to 2.5 MT (4,409-5,512 LBS) is recommended to maximize container loading 8

9 Quality Control With the advanced test equipment and machines, we could make the quality control in a consistent high level. Raw Material Elements Inspection Tensile testing machine Surface inspection 9

10 Applications Products Alloy Pictures Exterior façade cladding 3003 Sign boards 1050/3003/3005 Pre-painting 1050/3003/3105 Constructi on Suspended ceiling 3003/3105 Roofing 3003/3105 Composite panel 3003/3105 Door & Widows 1050/

11 Applications Air conditional 1000/3000 series Industry Insulation 1000/8000 series Cable foil 1000/8000 series Container foil 3000/8000 series Packaging Household foil 8000 series Bottle cap 3000/8000 series 11

12 Picture of factory 12

13 Picture of factory 13