Araldite 2013 Adhesive

Transcription

1 Araldite 2013 Adhesive Product Description Araldite 2013 structural adhesive is a two component, room temperature curing, paste adhesive of high strength and toughness. It is thixotropic with good environmental and chemical resistance. Although it is designed as a metal bonding adhesive it is also suitable for bonding other materials such as, ceramics, glass, rubbers, rigid plastics and most other materials in common use. Features Metal colored Suitable for vertical applications Low shrinkage Good environmental and chemical resistance Bonds a wide variety of materials Typical Properties* Property Araldite 2013 A Araldite 2013 B Mixed System Appearance Grey soft paste Beige soft paste Grey paste Density, g/cm 3 ~1.4 ~0.9 ~1.2 Viscosity at 25 C, cp 380, ,000 Thixotropic Thixotropic Pot life at 25 C, 100 g, min ~50 80 *Properties are based on Huntsman test methods. Copies are available upon request Processing Mix Ratio Product Parts by weight Parts by volume Araldite 2013 A Araldite 2013 B / 2015 Araldite 2013 Page 1

2 Pretreatment The strength and durability of a bonded joint are dependent on proper treatment of the surfaces to be bonded. At the very least, joint surfaces should be cleaned with a good degreasing agent such as acetone, isopropanol (for plastics) or other proprietary degreasing agents in order to remove all traces of oil, grease and dirt. Lowgrade alcohol, gasoline, or paint thinners should never be used. The strongest and most durable joints are obtained by either mechanically abrading or chemically etching ( pickling ) the degreased surfaces. Abrading should be followed by a second degreasing treatment. Araldite 2013 structural adhesive is available in cartridges incorporating mixers and can be applied as ready to use adhesive with the aid of the tool recommended by Huntsman. Application of adhesive The resin/hardener mix may be applied manually or robotically to the pretreated and dry joint surfaces. Huntsman's technical support group can assist the user in the selection of a suitable application method as well as suggest a variety of reputable companies that manufacture and service adhesive dispensing equipment. A layer of adhesive to in (0.05 to 0.10 mm) thick will normally impart the greatest lap shear strength to the joint. Huntsman stresses that proper adhesive joint design is also critical for a durable bond. The joint components should be assembled and secured in a fixed position as soon as the adhesive has been applied. For more detailed explanations regarding surface preparation and pretreatment, adhesive joint design, and the dual syringe dispensing system, visit Equipment Maintenance All tools should be cleaned with hot water and soap before adhesives residues have had time to cure. The removal of cured residues is a difficult and timeconsuming operation. If solvents such as acetone are used for cleaning, operatives should take the appropriate precautions and, in addition, avoid skin and eye contact. Cure times to reach minimum shear strength Temperature, F Cure time to reach LSS* > 145 psi (1 MPa), hours minutes Cure time to reach LSS > 1450 psi (10 MPa), hours minutes *LSS = Lap shear strength 10 / 2015 Araldite 2013 Page 2

3 Typical Physical Properties Unless otherwise stated, the data were determined with typical production batches using standard test methods. They are typical values only, and do not constitute a product specification. Unless a different specification is given, the figures below were all determined by testing standard specimens made by lapjointing 4.5 x 1 x in (114 x 25 x 1.6 mm) strips of aluminum alloy. The joint area was 0.5 x 1 in (12.5 x 25 mm) in each case. Samples were cured at 104 F (40 C) for 16 hours and tested at 23 C, unless otherwise noted. Property Value Test Method Average lap shear strength, metalmetal joints, sand blasting pretreatment, psi Aluminum Steel 37/11 Stainless steel V4A Galvanized steel Copper Brass 2,634 2,170 3,503 2,122 2,712 2,701 ISO 4587 Average lap shear strength, plasticplastic joints, lightly abrade and alcohol degrease pretreatment, psi GRP CFRP SMC ABS PVC PMMA Polycarbonate Polyamides Lap shear strength, after immersion in 23 C media, psi Asmade value IMS Gasoline Ethyl acetate Acetic acid, 10% Xylene Lubricating oil Paraffin Water at 73 F Water at 140 F Water at 194 F 30 days 2,286 2,730 2,321 1,913 2,473 2,176 2,321 1,827 1,877 2,002 1,204 1,769 1, days 2,158 2,648 2, ,056 2,611 2,466 1,740 1,740 1, days 2,811 1,936 2,466 3, ,764 2,986 2,975 2,975 1, ISO 4587 ISO / 2015 Araldite 2013 Page 3

4 Lap shear strength, exposure to tropical weather,* psi Asmade value 30 days 60 days 90 days Lap shear strength, heat aging at 158 F, psi Asmade value 30 days 60 days 90 days Roller peel test, pli (N/mm) Cure: 16 hours / 104 F (40 C) 20 min / 176 F (80 C) 2,698 2,828 2,640 2,335 2,799 2,944 2,480 3,046 DIN ISO (4.0) 23 (4.0) Flexural strength, psi (MPa) 6,686 (46.1) ISO 178 Flexural modulus, psi (MPa) 359,433 (2478.2) ISO 178 Shear modulus, psi (GPa) 77 F (25 C) 122 F (50 C) 167 F (75 C) 362,594 (2.5) 145,038 (1.0) 4,351 (0.030) DIN *40/92, DIN 50015; typical average values; test at 23 C. Figure 1. Lap shear strength versus temperature (ISO 4587) (typical average values) Cure: (a) = 7 days at 73 F (23 C); (b) = 24 hours at 73 F (23 C) + 30 min / 176 F (80 C) 10 / 2015 Araldite 2013 Page 4

5 Storage Araldite 2013 Adhesive should be stored in a dry place, in the original sealed containers, at temperatures between 2 C and 40 C (36 F and 104 F). Under these storage conditions, the product has a shelf life of 3 years (from date of manufacture). The product should not be exposed to direct sunlight. If stored below 60 F, the adhesive should be brought to 60 F 77 F and conditioned at this temperature for some time prior to use. Precautionary Statement Huntsman Americas LLC maintains uptodate Safety Data Sheets (SDS) on all of its products. These sheets contain pertinent information that you may need to protect your employees and customers against any known health or safety hazards associated with our products. Users should review the latest MSDS to determine possible health hazards and appropriate precautions to implement prior to using this material. First Aid! Refer to SDS as mentioned above. KEEP OUT OF REACH OF CHILDREN FOR PROFESSIONAL AND INDUSTRIAL USE ONLY 10 / 2015 Araldite 2013 Page 5

6 Important Legal Notice Sales of the product described herein ( Product ) are subject to the general terms and conditions of sale of either Huntsman LLC, or its appropriate affiliate including without limitation Huntsman Advanced Materials (Europe) BVBA, Huntsman Americas Inc., or Huntsman (Hong Kong) Ltd. ( Huntsman ). The following supercedes Buyer s documents. Huntsman warrants that at the time and place of delivery all Products sold to Buyer shall conform to the specifications provided to Buyer by Huntsman. While the information and recommendations included in this publication are, to the best of Huntsman s knowledge, accurate as of the date of publication, NOTHING CONTAINED HEREIN (EXCEPT AS SET FORTH ABOVE REGARDING CONFORMANCE WITH SPECIFICATIONS PROVIDED TO BUYER BY HUNTSMAN) IS TO BE CONSTRUED AS A REPRESENTATION OR WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, NONINFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHTS, OR WARRANTIES AS TO QUALITY OR CORRESPONDENCE WITH PRIOR DESCRIPTION OR SAMPLE, AND THE BUYER ASSUMES ALL RISK AND LIABILITY WHATSOEVER RESULTING FROM THE USE OF SUCH PRODUCT, WHETHER USED SINGLY OR IN COMBINATION WITH OTHER SUBSTANCES. No statements or recommendations made herein are to be construed as a representation about the suitability of any Product for the particular application of Buyer or user or as an inducement to infringe any patent or other intellectual property right. Buyer is responsible to determine the applicability of such information and recommendations and the suitability of any Product for its own particular purpose, and to ensure that its intended use of the Product does not infringe any intellectual property rights. The Product may be or become hazardous. The Buyer should obtain Material Safety Data Sheets and Technical Data Sheets from Huntsman containing detailed information on Product hazards and toxicity, together with proper shipping, handling and storage procedures for the Product, and should comply with all applicable governmental laws, regulations and standards relating to the handling, use, storage, distribution and disposal of, and exposure to the Product. Buyer shall also take all steps necessary to adequately inform, warn and familiarize its employees, agents, direct and indirect customers and contractors who may handle or be exposed to the Product of all hazards pertaining to and proper procedures for safe handling, use, storage, transportation and disposal of and exposure to the Product, and the containers or equipment in which the Product may be handled, shipped or stored. Araldite is a registered trademark of Huntsman LLC or an affiliate thereof in one or more, but not all countries Huntsman Inc. Main Offices: Huntsman Corporation Woodloch Forest Dr The Woodlands, TX Huntsman Advanced Technology Center 8600 Gosling Rd. The Woodlands, TX / 2015 Araldite 2013 Page 6