Manufacturers declaration of performance

Transcription

1 Trespa International B.V. P.O. Box 110, 6000 AC Weert Wetering 20, 6002 SM Weert, The Netherlands Tel.: 31 (0) , Fax: 31 (0) Manufacturers declaration of performance Trespa International BV declares that TRESPA TOPLAB PLUS is in conformity with specifications according to the mentioned tests : Valid for the Trespa Toplab PLUS delivery program. Behaviour in case of fire Not tested CGS / -4 Mechanical / physical properties CGS / -4 Density ISO 1183 kg/m Flexural modulus Stress ISO 178 N/ Flexural strength Stress ISO 178 N/ Tensile strength Stress ISO N/ 2 70 Resistance to impact by large diameter ball: Drop height 1800 Mass of steel ball 324 g Diameter of indentation 0 Resistance to scratching Load Rating 4 Resistance to surface wear Uni colours Wear resistance Revolutions: Initial point Wear value Speckle Wear resistance Revolutions: Initial point Wear value Resistance to dry heat at 160 C Appearance Rating 4 Resistance to wet heat at 100 C Appearance EN Rating 4 Dimensional stability at elevated temperature Cumulative dimensional % 0,25 Resistance to iersion in boiling water after 2 hrs change Mass increase Thickness increase Appearance % % rating Resistance to steam Appearance Rating 4 Resistance to crazing Appearance Rating 4 Resistance to colour change Contrast ASTM G53-91 Wool scale 6 (UV-A) ( nm) Resistance to staining Appearance Groups 1 and 2 Group 3 Rating 5 5 Resistance to cigarette burns Appearance Rating 4 4 1/5

2 Product inspection finished products Panel dimensions Thickness t CGS / -4 5 t < 8 : ± 0,4 8 t < 12 : ± 0,5 12 t < 16 : ± 0,6 16 t < 20 : ± 0,7 20 t < 25 : ± 0,8 25 t : in consultation with the customer Size Tolerance length and width: -0 / +5 1 SF: 2550 x IF: 3050 x 1530 Squareness Length of diagonals: SF 1 : 3156 ± 13 IF 2 : 3412 ± 14 Straightness of edges /m Colour difference Flatness Deviation from original sample in Trespa archive ISO 7724 /m 2 Ecmc Uni colours : 0,8 Gloss variations Surface quality Visual comparison with original sample Dirt, spots and similar defects 2 /m 2 Speckle : no visual detectable deviation No annoying flame effects, no detectable stripes Fibers, hairs and scratches /m 0 Chemical resistance Test procedures The tests where conducted following the PSI (Professional Service Industries/Pittsburg Laboratory Division) and the procedure by applying 5 drops of each reagent on the surface, covered by a watch glass (except those marked **). Chemicals marked ** were tested with a saturated cotton wool ball covered by a bottle. All chemicals were tested at room temperature for a period of 24 hours, rinsed off with water and evaluated. Test results The chemicals mentioned in the table include in bold the 49 chemicals/concentrations listed by (Scientific Equipment and Furniture Association) as well as the main reagents from the PSI (Professional Service Industries/Pittsburg Laboratory Division). All information is based on our current state of knowledge. It is intended as information concerning our products and their application possibilities, and is therefore not intended as any form of guarantee with regard to any specific product characteristic. Test results differ per color. Although the tests have been conducted according to the, it is recoended that users conduct their own tests. 2/5

3 The test was made by an independent laboratory (SGS North America) on 5 different product colours. scale No effects Excellent Good Fair Failure No detectable stain, loss of gloss or change in work surface material Slight stain or gloss, but no change to the function, smoothness or life of the work surface material A clearly discernible stain or loss of gloss, but no change to the function, smoothness or life of the work surface material Unacceptable staining or discernible deterioration or etching of work surface material Severe stain or moderate deterioration, pitting, cratering or etching of work surface material rating scale 0 No detectable change 1 Slight change in colour or gloss 2 Slight surface etching or severe staining 3 Pitting, cratering, swelling, erosion of coating, obvious & significant deterioration Acids No effect Excellent Good Fair Failure rating Acetic acid 98% 0 Acetic acid 99% Acid Dichromate 5% 0 Chromic Acid 60% 0 Formic Acid 90% 0 Hydrochloric acid 10% Hydrochloric acid 37% 0 Hydrofluoric acid 48% 3 Nitric Acid 20% 0 Nitric acid 30% 0 Nitric acid 30% (Speckle colours) Nitric acid 65% Nitric acid 65% (Speckle colours) Nitric Acid 70% 1 Nitric Acid 70% (Speckle colours) Nitric acid 65% / Hydrochloric acid 37% (1:3) Perchloric acid 60% Phosphoric acid 85% 0 Sulphuric Acid 25% Sulphuric acid 33% 0 Sulphuric acid 77% 0 Sulphuric acid 85% Sulphuric acid 96% 0 Sulphuric acid 98% Sulfuric Acid 77% / Nitric Acid 70% (1:1) 1 Sulfuric Acid 85% / Nitric Acid 70% (1:1) 3/5

4 Bases No effect Excellent Good Fair Failure rating Aonium hydroxide 28% 0 Sodium hydroxide 10% 0 Sodium hydroxide 20% 0 Sodium hydroxide 40% 0 Sodium Hydroxide Flake 0 Salts No effect Excellent Good Fair Failure rating Copper sulphate 10% Ferric (III) chloride 10% Potassium iodite 10% Potassium permanganate 10% Silver nitrate saturated 0 Sodium chloride 10% Sodium hypochlorite 13% Zinc Chloride Saturated 0 Halogens No effect Excellent Good Fair Failure rating Iodine ( crystals ) Iodine solution ( 0.1 N ) Tincture of Iodine x 1 Organic Chemicals No effect Excellent Good Fair Failure rating Cresol 0 Dimethylformamide 0 Formaldehyde 37% 0 Furfural 0 Gasoline 0 Hydrogen Peroxide 3% Hydrogen Peroxide 30% 0 Phenol 90% 0 Sodium Sulfide Saturated 0 Solvents** No effect Excellent Good Fair Failure rating Acetic anhydride Acetone 0 Acetonitrile Amyl Acetate 0 Benzene 0 Butyl Alcohol 0 Carbon Tetrachloride 0 Chloroform 0 Dichlor Acetic Acid 0 Dichloromethane / Methylene Chloride 0 4/5

5 Dioxane 0 Diethyl Ether 0 Ethylacetate 0 Ethylalcohol 0 Ethylene glycol Methylalcohol 0 Methylethylketone 0 Methylisobutylketone Mono Chlorobenzene 0 Napthelene 0 n-butyl acetate Tetrahydrofurane n-hexane Toluene 0 Trichloroethylene 0 ylene 0 Biological Stains No effect Excellent Good Fair Failure rating Acridine orange 1% Alizarin complexone dehydrate 1% Aniline blue, water soluble 1% Basic fuchsin 1% Carbol fuchsin 1% Carmine 1% Congo red 1% Gentian violet (dye) 1% Eosin B 1% Giemsa stain 1% Malachite green oxalate 1% Methyl violet 2B 1% Methylene blue 1% Safranine O 1% Sudan III 1% Wright stain 1% Most conventional cleaning agents No effect Excellent Good Fair Failure rating Document created by: Trespa Technology Center / Product Management - Code: U5305- Version: February 2011 Responsibility Despite the utmost care and attention to the content of this document by Trespa International B.V., it cannot give any warranty as to the accuracy or completeness of the information in this document. The information in this document is intended to serve general information purposes only. Trespa International B.V. makes no warranties or representations, express or implied that the information in this document is fit for the purpose of the reader. Trespa International B.V. does not accept any liability for any direct or indirect damages of whatever nature, in anyway resulting from the use of this document and/or the use of information that is gathered through this document. Copyrights All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or made public, in any form or by any means, either graphic, electronic or mechanical, including photocopying, recording or otherwise, without the prior written permission of Trespa International B.V. Registered trademarks Trespa, Meteon, Athlon, TopLab, TopLab PLUS, TopLab ECO-FIBRE, Virtuon, Volkern, Mystic Metallics and Trespa Essentials are registered trademarks of Trespa International B.V. 5/5