1 Overview of Refinishing Systems for Passenger Cars VOC

Transcription

1 1 Overview of Refinishing Systems for Passenger Cars VOC 1-1 Warranty Painting Systems Passenger Cars Warranty Painting Systems for Metal Substrates Painting System for Total Respray and Spot Repair Painting of Stone Chip Areas N/A N/A Painting System for Cars with Matt Finish N/A Warranty Painting Systems for Plastic Substrates Not VOC-compliant Not VOC-compliant Not VOC-compliant Not VOC-compliant Stage with Standohyd Basecoat - Hard Plastics N/A Stage with Standohyd Basecoat - Hard Plastics N/A 1-2 Model Specific Recommendations Refinishing Recommendation for Mercedes Benz A Class Recommended Procedure for Painting of Maybach Typ Painting System SLR Repair Painting System for Mercedes Benz smart Tridion Cell Magno Colours Painting System for Cars with Matt Finish Magno Colours Alubeam Alubeam Blendingin with Standohyd Basecoat Mercedes Alubeam Overview Bright Colours [S9.5] Blending-in with 3-Stage Standohyd Basecoat (Spot Repair) [S9.6] Blending-in with 3-Stage Standohyd Basecoat into adjacent panels [S15.1] Blending-in with 3-Stage Standoblue Basecoat [S15.3] Blending-in with Standoblue Basecoat into adjacent panels 1-3 Economical Painting Systems UV Painting System for Small Surfaces Blending-in / Polishing of Standocryl VOC Platinum Clear 2 More Information 2-1 [S1] Substrate Pretreatment 2-2 Not VOC-compliant 2-3 [S10] Infrared Drying 2-4 [T5] Conversion Table 2-5 [T7] Pictograms 2-6 [T6] Mixing Sticks 2-7 Matting Tables Not VOC-compliant Not VOC-compliant N/A N/A [T8_5] Matting Table VOC Topcoat [T8_6] Matting Table VOC Clearcoat - Special Matt

2 2-8 Temperature Tables [T3_2A] Temperature Table 2K Thinners Not VOC-compliant [T3_2C] Temperature Table VOC Thinner [T3_1B] Temperature Table Hardener HS [T3_1A] Temperature Table Hardener MS [T3_1C] Temperature Table VOC Hardener 2-9 Blending-in with Standohyd Basecoat [S9.5] Blending-in with 3-Stage Standohyd Basecoat (Spot Repair) [S9.6] Blending-in with 3-Stage Standohyd Basecoat into adjacent panels [S9.7] Blending-in with Standohyd Basecoat (Spot Repair) [S9.8] Blending-in with Standohyd Basecoat into adjacent panels 3 Technical Data Sheets for Mercedes-Benz Passenger Car Refinishes 3-1 Stoppers / Spray Filler Standox Fine Stopper U Standox Spray Filler U Standox Rapid Stopper U Standox Soft Stopper U Primer Standox Etching Adhesion PrimerU Standox 1K Primer Filler U (for small through-sanded areas only) Standox SprayMax 1K Primer Filler U Standox SprayMax Etching Adhesion Primer U EP Primer Surfacer Standox EP Primer Surfacer U MB Standox SprayMax EP Primer Surfacer U MB 3-4 Filler Standox VOC Nonstop Primer Filler U MB Standox VOC System Filler U Standoflash UV Filler U Standox VOC Xtra Filler U Topcoats Not VOC-compliant N/A Not VOC-compliant Standohyd Basecoat Standocryl VOC Topcoat Alubeam Clearcoats Standocryl VOC HS Clear K Standocryl VOC Platinum Clear K Standocryl VOC Premium Clear K Standox Special Matt Standocryl VOC Express Clear K Standocryl VOC Xtra Clear K Products for Plastic Paintings Standox Plasticiser Standoflex Plastic Primer N/A Standoflex Pore Filler U Standoflex 2K Plastic Primer Surfacer U N/A Standocryl 2K Plastic Clear Satin Gloss 569

3 3-8 Waterborne Products Standox Cleaner Standox Deagreaser TB Standohyd Stone Chip Primer Blend-In Additives Smart Blend Plus Smart Blend Plus Not VOC-compliant Standohyd Color Blend Preparation and Cleaning Products Silicone Remover NEW N/A Cleaning Thinner E Cleaning Thinner T Standoblue Basecoat Standoblue Basecoat Standoblue Viscosity Adjuster Standoblue Viscosity Adjuster Slow NEW Standoblue Color Blend / Color Blend Slow Standoblue Hardener [S15.1] Blending-in with 3-Stage Standoblue Basecoat [S15.2] Blending-in with Standoblue Basecoat (Micro Repair) [S15.3] Blending-in with Standoblue Basecoat into adjacent panels [S15.4] Blending-in with Standoblue Basecoat (panel repair)

4 1.1.1 Standox Guidelines for Mercedes-Benz Passenger Car Refinishing Warranty Painting Systems for Metal Substrates (VOC) Warranty Painting Systems Total Respray / Spot Repair Painting of Stone Chip Areas Painting of cars with a matt finish Working Steps All substrates which occur on Mercedes-Benz Substrates passenger cars All substrates which occur on Mercedes-Benz passenger cars All substrates which occur on Mercedes-Benz passenger cars Cleaning, Preparation Standox Silicone Remover NEW Standox Cleaner Standox Silicone Remover NEW or Standox Precleaner Stopper Standox Fine Stopper U1070 Standox Rapid Stopper U1080 Standox Soft Stopper U1090 Standox Fine Stopper U1070 Standox Rapid Stopper U1080 Standox Soft Stopper U1090 Standox Fine Stopper U1070 Standox Rapid Stopper U1080 Standox Soft Stopper U1090 Primer (only metal substrates) Standox Etching Adhesion Primer U3100 or Standox 1K Primer Filler U3010 (for small throughsanded areas only) Standox Etching Adhesion Primer U3100 or Standox 1K Primer Filler U3010 (for small throughsanded areas only) Standox Etching Adhesion Primer U3100 or Standox 1K Primer Filler U3010 (for small throughsanded areas only) Filler Standox VOC System Filler U7540 Standox VOC Xtra Filler U7560 with 10% Standox Plasticiser Standox VOC System Filler U7540 Standox VOC Xtra Filler U7560 with 30% Standox Plasticiser Standox VOC System Filler U7540 Standox VOC Xtra Filler U7560 with 10% Standox Plasticiser Primer Surfacer Standox EP Primer Surfacer U7200 Standox EP Primer Surfacer U7200 Standox EP Primer Surfacer U7200 Cleaning Standox Cleaner Standox Cleaner Standox Cleaner Basecoat Standohyd Basecoat Standohyd Basecoat Standohyd Basecoat 2K Clear Standocryl VOC HS Clear K9520 Standocryl VOCPremium Clear K9540 Standocryl VOC Xtra Clear K9560 Standocryl VOC Express Clear K9530 Standocryl VOC HS Clear K9520 Standocryl VOCPremium Clear K9540 Standocryl VOC Xtra Clear K9560 Standocryl VOC Express Clear K9530 Standocryl VOC HS Clear K9520 Standox Special Matt In case of scratching resistant clears with a "C" in the type plate Standocryl VOC Platinum Clear K9570 Standocryl VOC Platinum Clear K9570 2K Acrylic Topcoat Standocryl VOC Topcoat Standocryl VOC Topcoat PKW-Mercedes-Benz / Welt I-2014 GB (VOC)

5 Standox Warranty Painting Systems for Mercedes-Benz Application: Metal substrates Spot repair and total respray Substrate: Bare metal, sanded Galvanised metal, sanded Aluminium, sanded Through-hardened sanded paintwork Pretreatment / Cleaning: For substrate preparation information see Standox Painting System S1. Stopper: Standox PE Rapid Stopper or Standox PE Soft Stopper Standox PE Fine Stopper Primer: Filler: Topcoat: Standox Etching Adhesion Primer or Standox 1K Primer Filler (for small through-sanded areas only) Do not overcoat with Standox EP Primer Surfacer, if Standox Etching Adhesion Primer or Standox 1K Primer Filler is used. Standox EP Primer Surfacer or Standox VOC System Filler with 10% Standox 2K Plasticiser Standocryl VOC Topcoat Standohyd Basecoat with Standocryl 2K HS Clear or Standocryl VOC Platinum Clear or Standocryl VOC HighPro Clear or Standocryl VOC Premium Clear or Standocryl VOC Xtra Clear or Standocryl VOC Express Clear Standox - Mercedes-Benz I-2012 VOC SX-GB 1/1

6 Standox Warranty Painting Systems for Mercedes-Benz Application: Metal substrate Painting of stone chip areas Substrate: Bare metal, sanded Galvanised metal, sanded Aluminium, sanded Through-hardened sanded paintwork Pretreatment / Cleaning: For substrate preparation information see Standox Painting System S1. Stopper: Standox PE Rapid Stopper or Standox PE Soft Stopper Standox PE Fine Stopper Primer: Filler: Stone Chip Protection: Standox Etching Adhesion Primer or Standox 1K Primer Filler (for small through-sanded areas only) Do not overcoat with Standox EP Primer Surfacer, if Standox Etching Adhesion Primer or Standox 1K Primer Filler is used. Standox EP Primer Surfacer or Standox VOC System Filler with 30% Standox 2K Plasticiser Standohyd Stone Chip Primer Topcoat: Standox - Mercedes-Benz Standocryl VOC Topcoat or Standohyd Basecoat with Standocryl 2K HS Clear or Standocryl VOC Platinum Clear or Standocryl VOC HighPro Clear or Standocryl VOC Premium Clear or Standocryl VOC Xtra Clear or Standocryl VOC Express Clear I-2012 VOC SX-GB 1/1

7 Standox Warranty Painting Systems for Mercedes-Benz Use: Metal or plastic substrates Panel repair and total respray Painting of cars with matt finish Substrate: Bare metal, sanded Galvanised metal, sanded Aluminium, sanded Through-hardened sanded paintwork Plastic substrates Pretreatment / Cleaning: For substrate preparation see Standox Painting System S1 Stopper: Standox PE Rapid Stopper or Standox PE Soft Stopper Standox PE Fine Stopper Primer: Filler: Standox Etching Adhesion Primer or Standox 1K Primer Filler (for small through-sanded areas only) Do not overcoat with Standox EP Primer Surfacer, if Standox Etching Adhesion Primer or Standox 1K Primer Filler is used. Standox EP Primer Surfacer or Standox VOC Fillers Basecoat: Standohyd Basecoat Clearcoat: Pre-Mixing: Standox 2K Special Matt Standocryl HS Clear Depending on desired gloss level the following mixtures are possible by mixing Standox 2K Special Matt and Standocryl HS Clear: 70:30 ratio for OEM surfaces* 75:25 ratio for OEM surfaces* Standox - Mercedes-Benz I-2010 VOC SX-GB 1/3

8 Standox Warranty Painting Systems for Mercedes-Benz Pre-Mixing (continued): 80:20 for the most Matt surface, normally not on OEM surfaces ** *Dependant on individual vehicle as OEM finishes vary in gloss level Shake or stir Standox 2K Special Matt well in the can. Ensure both components are thoroughly mixed. Mixture must be re-stirred if left to stand for 30 minutes or longer. Hardener and thinner should be added directly before application. Mixing: 4:1 with Standox VOC Hardener and 10 % Standox VOC Thinner Slow 17-18s/DIN 4mm/20 C 41-45s/ISO 4mm/20 C Potlife 30 minutes Application: * Compliant mm at bar inlet pressure ** SATA HVLP 1.5 mm at 2.0 bar inlet pressure Apply in two coats with increased distance to the object min flash off 2nd coat should be applied after visual flash off when surface begins to turn patchy. Apply the first and second layer in 90 cross application, if possible min final flash off Drying: Drying time min. / C object temperature Air dry is not permitted. Important remarks: Always make test panel to determine desired gloss level. Strictly adhere to the specified material adjustments. Standox - Mercedes-Benz I-2010 VOC SX-GB 2/3

9 Standox Warranty Painting Systems for Mercedes-Benz Important remarks (continued): Dust inclusions cannot be removed by polishing. Therefore maximum cleanliness should be obtained in the application process. Blending not possible ** Option: Depending on the color it is possible to cover Standohyd Basecoat with Standocryl VOC Clears baked and sanded. This gives more uniform result, especially on very dark colors. Care of the finish: Do not wash the car with a high-pressure or steam-jet cleaner. You can wash the car in an automatic car wash. Systems with soft brushes are preffered. Car washes with brushes do not necessarily have a negative impact on the paint surface or on the sensitivity to scratching. Do not use any paint cleaning compounds, sanding or polishing pastes/compounds, or even gloss preservers (wax) for paintwork care. They may damage the surface. If, by accident wax gets on the surface, remove it immediately with Standox Silicone Remover. Take care not to exert high pressure on the paint surface. Do not allow any resinous, greasy or oily substances to get on the paint surface, as these may leave traces. Tar spots can be removed with a commercial tar remover. Do not attach any stickers, foils, magnetic labels or similar to the painted surface. Standox - Mercedes-Benz I-2010 VOC SX-GB 3/3

10 1.1.2 Standox Guidelines for Mercedes-Benz Passenger Car Refinishing Warranty Painting Systems for Plastic Substrates Warranty Painting Systems / / / / Conventional 3-stage Non-VOC Conventional 2-stage Non-VOC 3-stage with Standohyd Basecoat VOC 2-stage with Standohyd Basecoat VOC Working Steps Substrates Originally primed (OEM) replacements parts, old paintwork, PP/EPDM, ABS,SAN, PC, PA, PUR, RIM, PPO, PBT, UPG, R-TPU Cleaning, Preparation Standoflex Plastic Cleaner antistatic Standoflex Plastic Cleaner antistatic Standoflex Plastic Cleaner antistatic Standoflex Plastic Cleaner antistatic Stopper Standox Fine Stopper U1070 1) Standox Fine Stopper U1070 1) Standox Fine Stopper U1070 1) Standox Fine Stopper U1070 1) Primer (only for sand-through or unprimed parts) Standoflex Plastic Primer U3060 Standoflex Plastic Primer U3060 Filler / Hardener (Wet-on-Wet procedure) Standox VOC Nonstop Primer Filler U7550, plasticised Standoflex 2K Plastic Primer Surfacer U3200 Standox VOC Nonstop Primer Filler U7550, plasticised Standoflex 2K Plastic Primer Surfacer U3200 Primer for sand-through areas Cleaning Standoflex Plastic Cleaner antistatic Standoflex Plastic Cleaner antistatic Standoflex Plastic Cleaner antistatic Standoflex Plastic Cleaner antistatic Basecoat Standox Basecoat Standox Basecoat Standohyd Basecoat Standohyd Basecoat 2K Clear Hardener gloss mat Standocryl 2K Plastic Clear Satin Gloss Standocryl Clears with Standox Special Matt Standocryl 2K Plastic Clear Satin Gloss Standocryl Clears with Standox Special Matt Standocryl 2K Plastic Clear Satin Gloss Standocryl Clears with Standox Special Matt Standocryl 2K Plastic Clear Satin Gloss Standocryl Clears with Standox Special Matt 2K Topcoat + Plasticiser Standocryl 2K Topcoat Standox Plasticiser Standocryl 2K Topcoat Standox Plasticiser Standocryl VOC Topcoat Standox Plasticiser Standocryl VOC Topcoat Standox Plasticiser Hardener 1) For the repair of small scratches PKW-Mercedes-Benz / Welt I-2014 DE 1.1.2

11 Standox Warranty Painting Systems for Mercedes-Benz Application: Plastic substrates 3-stage with Standohyd Basecoat Substrate: Exterior hard plastic parts, e.g. PP/EPDM, ABS, PC, PA, PUR, R-TPU, PPO, PBT, UP-GF, PVC Pretreatment / Cleaning: Application: Important remarks: Bake for 60 min / C Clean several times with plenty of fresh Standoflex Plastic Cleaner Antistatic and an ultra fine pad. Reclean with Standoflex Plastic Cleaner Antistatic. Dry and prime Remove all traces of release agent! Standoflex Plastic Primer If necessary apply Standox PE Fine Stopper Standox VOC Nonstop Primer Filler with 15% Standox 2K Plasticiser Standocryl VOC Topcoat with 15% Standox 2K Plasticiser or Standohyd Basecoat with Standocryl 2K Plastic Clear Satin Gloss or Standocryl 2K Clears with Standox 2K Special Matt Do not steam clean the finish within 6 weeks of application and drying. Then keep a minimum distance of 30 cm between the jet nozzle and the surface. Standox - Mercedes-Benz I-2012 VOC SX-GB 1/1

12 Standox Warranty Painting Systems for Mercedes-Benz Application: Plastic substrates 2-stage with Standohyd Basecoat Substrate: Pretreatment / Cleaning: Application: Important remarks: Exterior hard plastic parts, e.g. PP/EPDM, ABS, SAN, PC, PA, PUR, R-TPU, PPO, PBTP, UP-GF, PVC Bake for 60 min / C Clean several times with plenty of fresh Standoflex Plastic Cleaner Antistatic and ultra fine pad. Reclean with Standoflex Plastic Cleaner Antistatic. Dry and prime Remove all traces of release agent! Standoflex 2K Plastic Primer Surfacer For filling small scratches and imperfections, after pre-priming with Standoflex 2K Plastic Primer Surfacer and drying according to instructions, apply Standox PE Fine Stopper. After denibbing the body filler spot should be isolated with Standoflex 2K Plastic Primer Surfacer. Standohyd Basecoat with Standocryl 2K Plastic Clear Satin Gloss or Standocryl 2K Clears with Standox 2K Special Matt or Standocryl VOC Platinum Clear Do not steam clean the finish within 6 weeks of application and drying. Then keep a minimum distance of 30 cm between the jet nozzle and the surface. Standox - Mercedes-Benz I-2012 VOC SX-GB 1/1

13 Standox Warranty Painting Systems for Mercedes-Benz Application: Refinishing Recommendation for Mercedes Benz A Class Substrate: Powder slurry coating on metal and PPE/PA plastic Pretreatment / Cleaning: Standox Silicone Remover Stopper: Filler: Drying possibilities: Sanding: Only on bare sheet or plastic substrate with PE Fine Stopper Standox EP Primer Surfacer Important: Standox EP Primer Surfacer is used on both metal and plastics. Do not use plastic primers / fillers! To avoid swelling, any defective sanding or through-sanding of the OEM clear must be isolated using EP Primer Surfacer. a) 40 min / C b) 30 min / 80 C c) 16 h / C d) Short-wave IR drying in two steps: 1. step: 8 min at 50% power 2. step: 10 min at 100% power Important: Important: The radiator distance should be exactly 80 cm, but must by no means be smaller. Dry sand with P320 - P400 Wet sand with P600 - P800 Basecoat: Standohyd Basecoat Clearcoat: Standocryl 2K HS Clear or Standocryl VOC HighPro Clear or Standocryl VOC Premium Clear or Standocryl VOC Xtra Clear or Standocryl VOC Express Clear Standox - Mercedes-Benz I-2012 VOC SX-GB 1/1

14 Standox Warranty Painting Systems for Mercedes-Benz Application: Recommended Procedure for Painting of Maybach Typ 240 Substrate: Special Hint: Stopper: Filler: Basecoat: Clearcoat: Sanding of clearcoat: Aluminium or EDP, primed Clean with Standox Silicone Remover Dry sand with P280 - P400 Clean with Standox Silicone Remover Apply a compact coat of Standox EP Primer Surfacer on bare parts. After drying apply Standox EP Primer Surfacer Dry sand P240 - P320 Apply Standox PE Soft Stopper Dry sand P80 - P180 Clean with Standox Silicone Remover If necessary apply Standox Spray Filler Dry sand P120 - P240 Clean with Standox Silicone Remover Apply Standox Etching Adhesion Primer Apply Standox VOC System Filler with 10% Standox Plasticiser or Standox EP Primer Surfacer (no Etching Adhesion Primer under EP Primer Surfacer) Dry sand P400 - P500 Clean with Standox Silicone Remover Apply first colour shade with Standohyd Basecoat Standocryl 2K HS Clear or Standocryl VOC Platinum Clear or Standocryl VOC HighPro Clear or Standocryl VOC Premium Clear or Standocryl VOC Xtra Clear or Standocryl VOC Express Clear Dry clearcoat After drying the clearcoat must be sanded Pre-sanding with P1500, wet, and final sanding with P2000, wet Standox - Mercedes-Benz I-2012 VOC SX-GB 1/2

15 Standox Warranty Painting Systems for Mercedes-Benz Mask: Basecoat: Clearcoat: Sanding of clearcoat: Finish: Drying: Processing after cooling down: Polishing: Important remarks: Demask vehicle to remove sanding waste. Prepare the vehicle for the second colour shade. Apply second colour shade with Standohyd Basecoat. Standocryl 2K HS Clear or Standocryl VOC Platinum Clear or Standocryl VOC HighPro Clear or Standocryl VOC Premium Clear or Standocryl VOC Xtra Clear or Standocryl VOC Express Clear Dry clearcoat After drying the clearcoat must be sanded. Pre-sanding with P1500, wet, and final sanding with P2000, wet Apply Standocryl VOC Platinum Clear using Standox VOC Hardener Oven dry min / C panel temperature, followed by IR drying (short wave) for at least 12 min at 100% power Sand dust inclusions with 3M VP 2000 pads or 3M Trizact P3000 (see Polishing Process). Polish with a rotary polishing machine and the 3M wool pad. Apply a small amount of 3M Finesse-it Polish Extra Fine to the pad. Polish with a rotary polishing machine and the 3M polishing foam orange (for better cooling). Apply a small amount of 3M Perfect-it (TM) III Extra Fine Sanding Paste to the foam. See Polishing Process S13 Oil and residue should be cleaned off with 3M Finish Control Spray or degreaser in order to check if it is necessary to reapply polish. If the finish is still not satisfactory, the last two process steps may be repeated if necessary. To give a better protection on the cleaned area, further polishing with a small amount of 3M Perfect-it (TM) III Extra Fine Sanding Paste on the orange pad is recommended. Standox - Mercedes-Benz I-2012 VOC SX-GB 2/2

16 Standox Warranty Painting Systems for Mercedes-Benz Application: Painting System SLR Substrate: Damages down to the substrate Pretreatment / Cleaning: For substrate preparation information see Standox Painting System S2.1. Stopper: Filler: Standox PE Fine Stopper Apply stopper on minor scratches in the substrate. Standox VOC System Filler Apply two spray passes (= 80 micron) first. After intermediate drying and sanding (see below) apply two more spray passes (= 80 micron). Air dry overnight / C or min. / C panel temperature IR Drying Short wave 8-10 min (see Standox Painting System S10) P240 - P320 orbital sander Basecoat: Standohyd Basecoat Clearcoat / Hardener: Important remarks: Standocryl 2K HS Clear or Standocryl VOC Premium Clear with all Standox 2K Hardeners HS or Standocryl VOC HighPro Clear with Standox VOC Hardener Standox VOC System Filler is supposed to equalize the structure of the substrate. Standox - Mercedes-Benz I-2010 VOC SX-GB 1/1

17 Standox Warranty Painting Systems for Mercedes-Benz Use: Repair Painting System for Mercedes-Benz smart city coupé / cabrio smart Tridion cell Substrate: Powder clear 1-stage powder paint (silver or black) Original paintwork with through-sanded areas to metal Metal or plastic parts see Painting Systems , or , Pretreatment / Cleaning: For substrate preparation see Standox Painting System S1 Stopper: Primer: Standox PE Fine Stopper Standox Etching Adhesion Primer (on bare metal only) Filler: Standox VOC Nonstop Primer Filler Air dry overnight / C or 30 min. / C panel temperature Dry sand P320 - P400 Wet sand P600 - P800 Basecoat: Standohyd Basecoat Clearcoat: Important remark regarding blending-in: Mixing of clear see Standox Matting Table HS Adjustment of the gloss level to the OEM painting (approx units) Metal frames with 1-stage powder paint anthracite-metallic cannot be blended in with clear. After blending-in with Standohyd Basecoat the complete frame side has to be overcoated with 2K Clear. Standox - Mercedes-Benz I-2010 VOC SX-GB 1/1

18 Overview Magno Colour range Colour MB No. Magno Allanite grey Magno Sabbia Magno Cashmere white Magno Platinum Magno Manganite grey Magno Sylvanite grey Magno Monza grey ( only AMG ) Magno Glacier grey Magno Cerussite grey Magno Night black 0 056

19 Standohyd Basecoat Mercedes Alubeam 047 Special effect colour Specific application process Technical Description: Thin with 50 % Standohyd Special Effect Additive Painting system S9.13 describes the special blending-in process SX-GB Version /3

20 Standohyd Basecoat Mercedes Alubeam 047 Substrate: Sanded Standox EP Primer Surfacer 3:1 or Standox VOC System Filler Through-hardened sanded paintwork Do not forget cleaning! Pretreatment / Cleaning: For substrate preparation see Standox Painting System S1 Use air fed respirator. Refer to relevant Health and Safety Data Sheets. 1 normal coat 1 light coat with increased distance to object Flash off time can be reduced by - Using air blower - Spray booth blower system - Infrared drying - Increasing spray booth temperature to max. 45 C until mat Application: A Standocryl VOC Clear must be applied completely over any repaired panels, then cured and sanded Orbital sanding machine P1000-P1500 Edges and corners P3000 handsanding Add 50% Standohyd Special Effect Additive to the Mercedes 047 colour for standard application. Gently shake Standohyd Special Effect Additive before use. Compliant mm 2.0 bar inlet pressure 1.5 = micron HVLP mm 0.7 bar atomization pressure 1.5 = micron Final flash off until matt Standocryl VOC Platinum Clear SX-GB Version /3

21 Standohyd Basecoat Mercedes Alubeam 047 Flashpoint: 50 C / 122 F Specific Gravity: 1,004 g/cm 3 Solid Content (without thinner added): 11.6 Weight % 10.0 Volume % VOC (2004/42/EC): 2004/42/IIB(d)(420)420 The EU limit value for this product (product category: IIB.d) in ready for use form is max 420 g/litre of VOC. The VOC content of this product in ready for use form is max. 420 g/l. Cleaning of equipment: Rinse first with Standohyd Demineralized Water. Clean after use with Standox Cleaning Thinner. Important remarks: The equipment for water thinnable products must be compatible with waterbased products. When collecting waste for disposal, separate waterthinnable products from conventional ones, otherwise waste disposal will be more difficult and expensive, if not impossible. Large blend-in possible only. Painting system S9.13 describes the special blending-in process Best results with SATA NR3000 HVLP 1.3 mm spray gun Theoretical Coverage: 11 m 2 /l at 15 micron dry film thickness Standohyd Special Effect Additive should be added to the Standohyd Mercedes 047 colour directly before application, best results are when used within same working day. For professional use only! The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose. The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved. The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed. We may modify and/ or discontinue operation of all or portions of this Information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. SX-GB Standox GmbH Postfach Version 00 D Wuppertal 697 3/3 Germany

22 Standox Painting Systems Working Process: Blending-in with Standohyd Basecoat Mercedes Alubeam 047 Substrate: Pretreatment / Cleaning: Prepare new panels as usual, see Standox Painting System S3 All panels with repaired filler areas must be clearcoated with a Standocryl VOC Clear in accordance to relevant TDS. Repaired and clearcoated panels are sanded with orbital sanding machine and P1000-P1500, edges and corners with P3000 handsanding. Blending area should be prepared with P3000 machine sanding. For substrate preparation see Standox Painting System S1 Painting: Apply Standohyd Special Effect Color Blend to surrounding fade out area or adjacent panels with closed coats. Blending-in transition areas: Mix Standohyd Basecoat Mercedes Alubeam 047 with 50% Standohyd Special Effect Additive, apply over repaired area and up to the edge of previously applied and still wet Standohyd Special Effect Color Blend film. Apply effect coat with increased distance over repaired area and blend into the Standohyd Special Effect Color Blend. Repaired panels areas: Mix Standohyd Basecoat Mercedes Alubeam 047 with 50% Standohyd Special Effect Additive, apply in 1.5 coat process and fade into adjacent areas. SX-GB Version 00 S9.13 1/2

23 Standox Painting Systems Working Process: Blending-in with Standohyd Basecoat Mercedes Alubeam 047 Painting (continued): Spray at bar pressure for effect coat. Ensure spraygun is used with full trigger. Do not allow Standohyd Special Effect Color Blend to flash off before applying the Standohyd Mercedes Alubeam 047 colour. Avoid overwetting the Standohyd Mercedes Alubeam 047 colour over the wet Standohyd Special Effect Color Blend. Apply Standocryl VOC Platinum Clear. SX-GB Version 00 S9.13 2/2

24 Overview Bright Colours Colour MB No. Comments Saphire Red SL B63 AMG Le Mans Red SLS AMG Cashmere White Magno Mystic White Diamant White Mystic White

25 Economical Standox Painting Systems Application: Recommended procedure for using Standoflash UV System for small repair Substrate: Bare metal, sanded Galvanised metal, sanded Aluminium, sanded Through-hardened sanded paintwork Pretreatment / Cleaning: For substrate preparation information see Standox Painting System S1. Stopper: Primer / Filler: Standoflash UV Stopper Standoflash UV Filler Topcoat: Standohyd Basecoat with Standoflash UV Clear Standocryl VOC Topcoat Standohyd Basecoat with Standocryl 2K HS Clear or Standocryl VOC Platinum Clear or Standocryl VOC HighPro Clear or Standocryl VOC Premium Clear or Standocryl VOC Xtra Clear or Standocryl VOC Express Clear The Standoflash UV system can only be introduced by technicians of the paint supplier. Standox - Mercedes-Benz I-2012 VOC 1.3 SX-GB 1/1

26 Standox Quality Painting Systems for Mercedes-Benz Application: Blending-in / Polishing of Standocryl VOC Platinum Clear Pretreatment / Cleaning: Sand the total fade out area carefully with a dual action sander with 3M Trizact Fine Finishing Disc P3000 3M mm (optional for small areas with 75mm disc). Any small dirt inclusions should be removed using Trizact A5 Film Discs (32mm) or Mirka Abralon P4000 before the actual process begins. Painting: Mix Standocryl VOC Platinum Clear 3:1 with Standox VOC Hardener Spray the repair area with catalysed clear. Apply pure Standox 2K Smart Blend Plus and ensure a smooth transition into the overlapping area. Drying: Oven drying min / C panel temperature Processing after cooling down: Polishing: Important remarks: Depending on the finish requirements sand the total area with P3000 Trizact Fine Finishing Disc (3M 50076) 150mm on a dual action sander. Particular care should be taken in the fade out area. Polish with a polishing machine and the 3M polishing foam orange (for better cooling). Apply a small amount of 3M Perfect-it (TM) III Extra Fine Sanding Paste to the foam. Oil and residue should be cleaned off with 3M Finish Control Spray or degreaser in order to check if it is necessary to reapply polish. If a satisfactory finish is not achieved, the last process step can be repeated. Standox - Mercedes-Benz I-2010 VOC SX-GB 1/1

27 Standox Painting Systems Working Process: Substrate Pretreatment Substrates: First Cleaning Mechanical Pretreatment Final Cleaning Bare Steel Standox Silicone Remover or Standox Degreaser TB 50 Dry sand P80 - P220 Standox Silicone Remover or Standox Degreaser TB 50 Soft Aluminium Standox Silicone Remover or Standox Degreaser TB 50 Dry sand P180 or Pad very fine Standox Silicone Remover or Standox Degreaser TB 50 Galvanised Substrates Standox Silicone Remover or Standox Degreaser TB 50 Pad ultra fine Standox Silicone Remover or Standox Degreaser TB 50 Old Paintwork Through-hardened Paintwork Through-hardened 2K Paintwork Through-hardened VOC Paintwork Through-hardened Synthetic Paintwork Standox Silicone Remover Standox Silicone Remover Standox Silicone Remover Standox Silicone Remover Dry sand P320 - P400 Wet sand P600 - P800 Dry sand P320 - P400 Wet sand P600 - P800 Dry sand P320 - P400 Wet sand P600 - P800 Dry sand P320 - P400 Wet sand P600 - P800 Standox Silicone Remover or Standox Precleaner Standox Silicone Remover or Standox Precleaner Standox Silicone Remover or Standox Precleaner Standox Silicone Remover or Standox Precleaner TPA Paintwork Standox Silicone Remover Wet sand P600 - P800 Standox Silicone Remover Cellulose Paintwork Standox Silicone Remover Wet sand P600 - P800 Standox Silicone Remover Powder Coated Paintwork Standox Silicone Remover Dry sand P320 - P400 Wet sand P600 - P800 Standox Silicone Remover or Standox Precleaner Soft Shop Paintwork Standox Silicone Remover or Standox Precleaner Dry sand P400 - P500 Wet sand P800 Standox Silicone Remover or Standox Precleaner SX-GB Version 06 S1 1/3

28 Standox Painting Systems Working Process: Substrate Pretreatment Substrates: First Cleaning Mechanical Pretreatment Final Cleaning Pre-primed Substrates EDP primed Standox Silicone Remover Dry sand P280 - P400 *) Wet sand P280 - P600 Standox Silicone Remover 1K Primer / Acid Primer If necessary Standox Silicone Remover Wet sand P800 Standox Silicone Remover 1K Cellulose Filler If necessary Standox Silicone Remover Wet sand P800 Standox Silicone Remover 2K Primer Surfacer / 2K / VOC Filler If necessary Standox Silicone Remover Dry sand P400 - P500 Wet sand P800 Standox Silicone Remover or Standox Precleaner Synthetic Primer / Synthetic Filler If necessary Standox Silicone Remover Wet sand P800 Standox Silicone Remover TPA Filler If necessary Standox Silicone Remover Wet sand P800 Standox Silicone Remover Powder Primer If necessary Standox Silicone Remover Wet sand P600 - P800 Standox Silicone Remover *) First cleaning as recommended is sufficient if the substrate is a perfect EDP primer coat SX-GB Version 06 S1 2/3

29 Standox Painting Systems Working Process: Substrate Pretreatment Substrates Tempering First cleaning Mechanical Pretreatment Final Cleaning Ventilation of the Solvents Plastics PC PP / EPDM PVC 60 min / C Use a Pad ultra fine soaked in Standoflex Plastic Cleaner antistatic Use a cloth moistened with Standoflex Plastic Cleaner antistatic Air dry overnight/ C or ABS and SAN UP-GF (former GRP) 20 min/ C panel temperature PU-RIM RTPU PUR PA 1) PPO PBTP PS (Polystyrene) 2) PE (Polyethylene) POM (Polyoxymethyle 1) 2) PA parts which have been tempered and oven-dried after painting should not be assembled immediately (risk of fracture). Further treatment see Standohyd Stone Chip Primer. cannot be (re)finished at bodyshops cannot be (re)finished Depending on the heat resistance of the plastic, suitable supports must be used for the add-on parts to avoid deformation. SX-GB Version 06 S1 3/3

30 !! " #$% &$ $ ' $$(!" #$$%&'$# ()$

31 )$% % * )$$+, * -$+, )$$+,!.,/(,/* #0* )- )$ )# - - # % )$ # 2 ". 3 % 4 5 # % 4!# )# )4 - - )# # 7) 2!#08. 3" " - - )% )5 )- )2 - - )% )5 % 7) )$ 7)9. : 9.(;4<:.* ; = ( 9.#$#<:.* = < 2$ )$$ = ()$ #$$%&'$#!"

32 Standox Painting Systems Conversion Table 1. Air Pressure 1 PSI (1 lb/sq.inch) = bar 1.0 bar 2.0 bar 3.0 bar 4.0 bar 5.0 bar 6.0 bar = = = = = = 14.2 PSI 28.4 PSI 42.7 PSI 56.9 PSI 71.2 PSI 87.0 PSI 2. Temperature C F = = = = = = = = = = = = = = = = = = = = SX-GB Version 06 T5 1/4

33 Standox Painting Systems Conversion Table 3. Viscosity DIN 4 mm/s FORD 4 mm/s BSB 4 mm/s ISO 3 mm/s ISO 4 mm/s ISO 5 mm/s AFNOR /s 10 = 7 = 11 = 22 = = = = 8 = 12 = 35 = = = = 9 = 14 = 48 = 20 = = = 11 = 15 = 63 = 24 = = = 13 = 17 = 77 = 28 = = = 15 = 18 = 92 = 33 = = = 16 = 20 = = 37 = = = 18 = 21 = = 41 = = = 19 = 23 = = 45 = = = 21 = 24 = = 49 = = = 22 = 26 = = 53 = = = 24 = 27 = = 57 = = = 25 = 28 = = 61 = = = 27 = 30 = = 65 = = = 28 = 32 = = 68 = = = 30 = 33 = = 72 = = = 31 = 34 = = 76 = = = 32 = 36 = = 80 = = = 34 = 38 = = 83 = = = 35 = 39 = = 87 = = = 36 = 41 = = 91 = = = 64 = = = = 71 = = 65 = = = = 72 = = 66 = = = = 74 = = 68 = = = = 75 = = 69 = = = = 76 = --- SX-GB Version 06 T5 2/4

34 Standox Painting Systems Conversion Table 4. Liquid Measure 1 oz. (ounce) 1 pt. (pint) 1 qt. (quart) 1 gal. (gallon) 1 oz. (ounce) 1 qt. (quart) 1 gal. (gallon) = ml UK 1.0 ml (millilitre) = oz. UK = l UK = l UK 1.0 l (litre) = qt. UK = l UK = ml USA = l USA = l USA 5. Weight 1 oz. (ounce) 1 lb. (pound) = = g g 1.0 kg (kilogramme) = lb. SX-GB Version 06 T5 3/4

35 Standox Painting Systems Conversion Table 6. Linear Measure 1 in. (inch) 1 ft. (foot) 1 yd. (yard) = = = 2.54 cm cm cm 1.0 mm 1.0 cm 1.0 m (millimetre) (centimetre) (metre) = = = in in in (1.09 yds.) 7. Coverage 1,0 m 2 = ft 2 8. Film Thickness micron (1 micron = mills) = = = = = = = mill (1 mill = 25.4 micron) SX-GB Version 06 T5 4/4

36 Pictograms 1. Preparation 1.1 Cleaning 2. Mixing Mixing ratio 2 components Mixing ratio 3 components Mixing ratio 1:1 2 components Use mixing stick Addition of hardener 3. Viscosity 3.1 Application viscosity 4. Application Gravity feed spray gun Suction feed Underseal spray gun Spray passes Gravity feed Compliant Spray passes Suction feed SX-GB Version 04 T7 1/3

37 Pictograms Spray passes Gravity feed HVLP One visit application One visit application One visit application Application of stopper Application with brush Application with roller Aerosol Airless spray 5. Drying Flash off Drying time Infrared drying time UV flash 6. Sanding / Polishing Sanding by hand, wet Sanding by Hand, dry Denibbing Orbital sander, wet (compressed air) Orbital sander, dry Flat bed sander, wet (compressed air) Flat bed sander, dry Polishing SX-GB Version 04 T7 2/3

38 Pictograms 7. Technical Information See Technical Data Sheet Use fresh air mask 8. Storage Store free from frost Store in a cool place Protect from humidity Close tin Shelf life 9. Miscellaneous Stirring Stirring on the mixing machine Check colour Poor opacity Three-coat process 9.6 Shaking SX-GB Version 04 T7 3/3

39 Standox Mixing Sticks Description Mixing Stick No. V: Art.No Reverse Standohyd Basecoat + 5 / 10 / 15% Demineralized Water Standocryl VOC HS Clear K9520 2:1 HS Hardener Mixing Stick No. Va (18 cm): Art.No Standohyd Basecoat + 5 / 10 / 15% Demineralized Water Reverse Standocryl VOC HS Clear K9520 2:1 HS Hardener Mixing Stick No. IX: Art.No :1 + 5 / 10 / 15 / 20% Reverse + 50 / 60% Mixing Stick No. X: Art.No :1 + 5 / 10 / 15 / 20% Reverse 4: / 15 / 20% Mixing Stick No. XI: Art.No : / 20 / 30% Reverse 7: / 20 / 30% SX-GB Version 08 T6 1/2

40 Standox Mixing Sticks Description Mixing Stick No. XII: Art.No Standoblue + 10% + 10 / 20% Reverse + 5% + 10 / 20% Mixing Stick No. XIIa (20 cm): Art.No Standoblue + 10% + 10 / 20% Reverse + 5% + 10 / 20% SX-GB Version 08 T6 2/2

41 Standox Matting Table VOC Topcoat Matting Standocryl VOC Topcoat with Standocryl 2K Matt MIX 606 Mixing ratio (in weight %) Gloss level (GE) according to DIN Standocryl VOC Topcoat 90 MIX angle GE* 60 angle GE* GE* GE* GE* GE* GE* GE* GE* GE* ,5-3 GE* 5-20 GE* GE* 2-4 GE* GE* 0-2 GE* Please note the mixing ratio change to 4:1 with Standox VOC Hardener when Standocryl 2K Matt MIX 606 is added. * = Depending on colour shade. Mixing bright colours with Standocryl 2K Matt MIX 606 influences the gloss level more than observed with dark colours. The gloss level can also be influenced by other factors, please refer to table influencing gloss level factors. For exterior car parts the mixing ratio must be minimum 50:50 for reasons of resistance and hiding power. SX-GB Version 03 T8.5 1/1

42 Standox Matting Table VOC Clearcoat Matting Standocryl VOC Clearcoats with Standox Special Matt All following recommendations are for bumpers and refinishing of ancillary parts only. For overall repair and matching OEM refinishing of specific matt finishes, use only Standocryl VOC HS Clear K9520 mixture and refer to painting system S14. Example: Standocryl VOC HS Clear K9520 Standox Special Matt 410g + 590g = 1.000g +2:1 Standox HS Hardener = Gloss level 40% VOC Clears Matt approx. 20% Satin Gloss approx. 40% Half gloss approx. 60% Gloss approx. 80% VOC Hardener HS Hardener Standocryl VOC Xtra Clear K9560 Standox Special Matt 290g +710g 360g +640g 430g +570g 560g 4:1 with Standox +440g VOC Hardeners % VOC 2K Additive Standocryl VOC Express Clear K9530 Standox Special Matt 290g +710g 350g +650g 420g +580g 590g 4:1 with Standox +410g VOC Hardeners % VOC Thinners Standocryl VOC Premium Clear K9540 Standox Special Matt 320g +680g 400g +600g 450g +550g 490g 4:1 with Standox +510g VOC Hardeners % VOC Thinners Standocryl VOC Premium Clear K9540 Standox Special Matt 300g +700g 390g +610g 440g +560g 490g +510g :1 with Standox HS Hardeners Standocryl VOC HS Clear K9520 Standox Special Matt 320g +680g 410g +590g 460g +540g 480g 4:1 with Standox +520g VOC Hardeners % VOC Thinners SX-GB Version 03 T8.6 1/2

43 Standox Matting Table VOC Clearcoat VOC Clears Matt approx. 20% Satin Gloss approx. 40% Half gloss approx. 60% Gloss approx. 80% VOC Hardener HS Hardener Standocryl VOC HS Clear K9520 Standox Special Matt 270g +730g 360g +640g 410g +590g 440g +560g :1 with Standox HS Hardeners Standocryl VOC 2K Clear K9550 Standox Special Matt 280g +720g 340g +660g 410g +590g 470g 4:1 with Standox +530g VOC Hardeners % Standocryl VOC 2K Additive Standocryl VOC Easy Clear K9510 Standox Special Matt 270g +730g 330g +670g 380g +620g 480g 3:1 with Standox +520g VOC Easy Hardeners Influencing gloss level factors: The use of different hardeners, thinners, methods of application, drying conditions and film thicknesses leads to different gloss levels (up to 20%). Higher Gloss level Hardener with higher solid content Faster Hardener Faster Thinner Higher viscosity Higher dry film thickness Shorter flash off times Forced drying Lower Gloss level Hardener with lower solid content Slower Hardener Slower Thinner Lower viscosity Lower dry film thickness Longer flash off times Air drying SX-GB Version 03 T8.6 2/2

44 Standox 2K Thinner Temperature Table 40 C Thinner 2K Thinner 2K C Thinner 2K Thinner 2K Thinner 2K Thinner 2K C Thinner 2K Thinner 2K Thinner 2K Thinner 2K Thinner 2K C 5 C Thinner 2K Thinner 2K Thinner 2K Thinner 2K SX-GB Version 05 T3.2A 1/1

45 Standox VOC Thinner Temperature Table 40 C Thinner VOC Thinner VOC C Thinner VOC Thinner VOC Thinner VOC C Thinner VOC Thinner VOC C Thinner VOC Thinner VOC C SX-GB Version 02 T3.2C 1/1

46 Standox HS Hardener Temperature Table 40 C Hardener HS Hardener HS C Hardener HS Hardener HS Hardener HS Hardener HS Hardener HS C Hardener HS Hardener HS Hardener HS C Hardener HS 5-15 Hardener HS C SX-GB Version 07 T3.1B 1/1

47 Standox MS Hardener Temperature Table 40 C Hardener MS Hardener MS C Hardener MS X Hardener MS Hardener MS X C Hardener MS X Hardener MS X 5-25 Hardener MS 5-15 Hardener MS X C 5 C Hardener MS X 5-25 Hardener MS 5-15 Hardener MS X 5-25 SX-GB Version 06 T3.1A 1/1

48 Standox VOC Hardener Temperature Table 40 C Hardener VOC Hardener VOC C Hardener VOC Hardener VOC Hardener VOC Hardener VOC Hardener VOC C Hardener VOC Hardener VOC Hardener VOC Hardener VOC Hardener VOC Hardener VOC C Hardener VOC C SX-GB Version 02 T3.1C 1/1

49 Standox Painting Systems Working Process: Blending-in with 3-Stage Standohyd Basecoat (Spot Repair) Substrate: For preparation of repair areas see Standox Painting System S3. Keep surface for priming with filler as small as possible. Pretreatment / Cleaning: Sand the repair area with P1000-P1200 wet and sand the whole panel with an ultra fine pad. For substrate preparation information see Standox Painting System S1. Painting: Mix Standohyd Basecoat ground colour with 5 % Standohyd Special Additive and then adjust to spray viscosity sec. DIN 4mm by adding Standox Demineralized Water as usual. Potlife of mixed material maximum 30 min. at 20 C. Apply Standohyd Basecoat ground colour until opacity to repair area (patch of filler) minutes final flash off followed by minutes at C object temperature. Allow surfaces to cool down to normal temperature. Apply Standohyd Basecoat effect colour to repair area and even out the pattern. Spray first coat to the widest area, if needed apply 2 nd and 3 rd coat with intermediate flash off. Work back from the widest area with staggered overlapping effect coats to avoid a strong halo / visible edge and provide a smooth transition. Start from widest area and work towards centre. After flashing off until matt remove spray dust carefully from entire area with a tack rag. Precoat repair area with 1 spray pass of any Standocryl VOC Clear, after flash off time overcoat the entire area with Standocryl VOC Clears. SX-GB Version 08 S9.5 1/2

50 Standox Painting Systems Working Process: Blending-in with 3-Stage Standohyd Basecoat (Spot Repair) Option: As an option of using Standohyd Special Additive, Standocryl VOC clears can be applied, dried and sanded to isolate the ground colour. Follow TDS Important hint: The usage of white or tinted Standox Fillers is recommended. SX-GB Version 08 S9.5 2/2

51 Standox Painting Systems Working Process: Blending-in with 3-Stage Standohyd Basecoat into adjacent panels Substrate: Prepare new panels as usual, see Standox Painting System S3 Pretreatment / Cleaning: Sand adjacent areas with P P1200 and an ultra fine pad For substrate preparation information see Standox Painting System S1. Painting: Mix Standohyd Basecoat ground colour with 5 % Standohyd Special Additive and then adjust to spray viscosity sec. DIN 4mm by adding Standox Demineralized Water as usual. Potlife of mixed material maximum 30 min. at 20 C. Mask adjacent panels. Apply Standohyd Basecoat ground colour to new panels until complete opacity has been reached. Remove masking and extend with ground colour into adjacent panel minutes final flash followed by minutes at C object temperature. Allow surfaces to cool down to normal temperature. Apply Standohyd Basecoat effect colour to the complete new part and blend-in to the adjacent parts. Spray first coat to the widest area, if needed apply 2 nd and 3 rd coat with intermediate flash off. Work back from the widest area with staggered overlapping effect coats to avoid a strong halo / visible edge and provide a smooth transition. Start from widest area and work towards centre. After flashing off until matt remove spray dust very carefully from entire area with a tack rag. SX-GB Version 08 S9.6 1/2

52 Standox Painting Systems Working Process: Blending-in with 3-Stage Standohyd Basecoat into adjacent panels Painting (continued): Precoat adjacent area with 1 spray pass of any Standocryl VOC Clear, after flash off time overcoat the entire area with Standocryl VOC Clears. Option: As an option of using Standohyd Special Additive, Standocryl VOC clears can be applied, dried and sanded to isolate the ground colour. Follow TDS. Important hint: The usage of white or tinted Standox Fillers is recommended. SX-GB Version 08 S9.6 2/2

53 Standox Painting Systems Working Process: Blending-in with Standohyd Basecoat (Spot Repair) Substrate: For preparation of repair areas see Standox Painting System S3. Keep surface for priming with filler as small as possible. Pretreatment / Cleaning: Sand the repair area with P1000-P1200 and go over the whole panel with an ultra fine pad. For substrate preparation information see Standox Painting System S1. Painting: Option: First apply one spray pass of Standohyd Color Blend to repair and fade out area. Apply Standohyd Basecoat with reduced viscosity (18-22 s / DIN 4mm / 20 C) and reduced spray pressure (by bar) with several spray passes to repair area and even out pattern to achieve opacity. After each spray pass, blow dry with an air gun. Blend-in in repair area. Option: RFU Standohyd Basecoat can also be mixed 1:1 with Standohyd Color Blend to make final spray passes of blend-in process. Apply one spray pass of Standocryl VOC Clear on blending-in area. After flash-off time apply Standocryl VOC Clear over complete area. SX-GB Version 06 S9.7 1/1

54 Standox Painting Systems Working Process: Blending-in with Standohyd Basecoat into adjacent panels Substrate: Prepare new panels as usual, see Standox Painting System S3 Pretreatment / Cleaning: Sand adjacent areas with P1000-P1200 and go over the whole panel with an ultra fine pad. For substrate preparation information see Standox Painting System S1. Painting: Apply Standohyd Basecoat to repair area to achieve opacity. Flash off until matt. Air blowers are recommended to reduce working time. Mix RFU Standohyd Basecoat 1:1 with Standohyd Color Blend. Fade out into adjacent panels with reduced spray pressure (by bar). Apply one spray pass of Standocryl VOC Clear on blending-in area. After flash-off time apply Standocryl VOC Clears over complete area. Option: First apply one spray pass of Standohyd Color Blend to repair and fade out area, but not up to undamaged edges of panels. Follow with procedure as described. SX-GB Version 06 S9.8 1/1

55 Technical Data Sheets Passenger Cars (VOC) TDS No. Hardeners and Accelerators Standox Hardener MS 5-15 Standox Hardener MS X 5-25 Standox Hardener MS X Standox Hardener MS Standox Hardener HS 5-15 Standox Hardener HS Standox Hardener HS Standox Hardener HS Standox Hardener VOC Standox Hardener VOC Standox Hardener VOC Standox Hardener VOC Standox Hardener VOC X Standox Hardener VOC X Thinners Standox Thinner 2K Standox Thinner 2K Standox Thinner 2K Standox Thinner 2K Standox Thinner 2K Standox Thinner VOC Standox Thinner VOC Stoppers / Spray Fillers Standox Fine Stopper U Standox Spray Filler U Standox PE Hardener U1110 Standox Rapid Stopper U Standox Soft Stopper U Standox Hardener Paste U1120 I / 3

56 Primers Standox Etching Adhesion Primer U Standox Etching Adhesion Activator U3110 Standox SprayMax Etching Adhesion Primer U Standox 1K Primer Filler U3010 (for small throughsanded areas only) 413 Standox SprayMax 1K Primer FillerU EP Primer Surfacers Standox EP Primer Surfacer U MB Standox EP Hardener U7210 Standox SprayMax EP Primer Surfacer U MB Fillers Standox VOC Xtra Filler U Standox VOC Nonstop Primer Filler U MB Standox VOC System Filler U Standoflash UV Filler U Standoflash UV Additive U7110 Topcoats Standoblue Basecoat 850 Standoblue Viscosity Adjuster Standoblue Hardener Standohyd Basecoat 801 Standohyd Special Additive Standocryl VOC Topcoat 554 Clearcoats Standocryl VOC HS Clear K Standocryl VOC Platinum Clear K Standocryl VOC Premium Clear K Standox Special Matt Standocryl VOC Express Clear K Standocryl VOC Xtra Clear K I / 3

57 Products for Plastic Paintings Standox Plasticiser 590 Standoflex Plastic Primer U Standoflex Pore Filler U Standoflex 2K Plastic Primer Surfacer U Standocryl 2K Plastic Clear Satin Gloss 569 Waterborne Products Standox Cleaner 803 Standox Degreaser TB Blend-In Additives Standoblue Color Blend / Color Blend Slow 851 Standox Smart Blend Plus 944 Standox Smart Blend Plus - Aerosol 1206 Standohyd Color Blend 806 Preparation and Cleaning Products Standox Silicone Remover NEW 992 Standox Cleaning Thinner E1 993 Standox Cleaning Thinner T2 994 I / 3

58 Standox Feinplastik U1070 Fine Stopper U1070 Polyester fine stopper Easy to spread Pore-free, fine surface Easy to sand, very good feather edging Suitable for steel, UP-GF and aluminium Technical Description: Mix with 2-3% Standox Hardener paste U1120 Potlife 4-5 min / C Do not apply to galvanised substrates Force drying possible Air dry min / C Dry sand P180 - P240 An Axalta Coating Systems Brand SX-GB Version /3

59 Standox Feinplastik U1070 Substrate: Application: Through-hardened sanded paintwork Bare steel, UP-GF and Aluminium, sanded 2-3% Standox Hardener paste U1120 Potlife 4-5 min / C Standox PE Stopper Through-hardened Standox Fillers, sanded Apply stopper Primed hard plastics Air dry min / C Coated hard plastics, sanded Pretreatment / Cleaning: For substrate preparation information see Standox Painting System S1. Short wave 2-3 min (see Standox Painting System S10) Dry sand P180 - P240 Standox Filler, Primer and Primer Surfacer Use air fed respirator. Refer to relevant Health and Safety Data sheets. SX-GB Version /3

60 Standox Feinplastik U1070 Flash point: 33 C / 91.4 F Cleaning of equipment: Clean after use with Standox Cleaning Thinner. Specific Gravity: 1.81 g/cm³ Solid Content (without thinner added): 84.1 Weight % 70.0 Volume % Important remarks: Polyester materials have a limited shelf life. Store in a cool place and use within 12 months for best results. Do not apply to Etch Primer, 1K Filler, TPA substrates and soft old paintwork. VOC (2004/42/EC): 2004/42/IIB(b)(250)170 The EU limit value for this product (product category: IIB.b) in ready for use form is max 250 g/litre of VOC. The VOC content of this product in ready for use form is max. 170 g/l. Do not apply at temperatures below +5 C. Mix the 2-3% Standox Hardener paste U1120 well with the stopper. Do not add more as this may cause staining of the topcoat finish. On galvanised substrates apply Standox Soft Stopper U1090 / Rapid Stopper U1080 coarse and fine. Hardener paste contains organic peroxide and is corrosive. If Hardener paste comes in contact with the skin, wipe off immediately and wash with soap and water. After eye contact irrigate copiously with a 2% aqueous sodium carbonate solution or water and seek medical advice. For professional use only! The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose. The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved. The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed. We may modify and/ or discontinue operation of all or portions of this Information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. SX-GB Version 07 Axalta Coating Systems Germany GmbH Christbusch Wuppertal 230 3/3 Germany

61 Standox Polyester-Spritzplastik U1100 Spray Filler U1100 Spray stopper Easy to sand Pore-free surface Can be used as a fine stopper Technical Description: Mix with 5% Standox PE Hardener U1110 Potlife min / C Film thickness up to 1000 micron Air dry 2 h / C or min / C panel temperature Force drying possible Dry sand Coarse sand P100 - P120 Fine sand P240 - P280 An Axalta Coating Systems Brand SX-GB Version /3

62 Standox Polyester-Spritzplastik U1100 Substrate: Application: Standox PE Stopper Through-hardened sanded paintwork Through-hardened Standox Fillers, sanded UP-GF, sanded Bare metal substrates and galvanised panels must be pre-primed with acid primer and Standox Filler. 5% Standox PE Hardener U1110 Potlife min / C Compliant mm bar inlet pressure 5 = max micron Air dry 2 h / C or min / C panel temperature Pretreatment / Cleaning: For substrate preparation information see Standox Painting System S1. Use air fed respirator. Refer to relevant Health and Safety Data sheets. 5 min / C Short wave min (see Standox Painting System S10) Coarse sand P100 - P120 Fine sand P240 - P280 Standox Silicone Remover Standox Filler SX-GB Version /3

63 Standox Polyester-Spritzplastik U1100 Flashpoint: 25 C / 77 F Cleaning of equipment: Clean after use with Standox Cleaning Thinner. Specific Gravity: 1.41 g/cm³ Solid Content (without thinner added): 70.6 Weight % 55.7 Volume % VOC (2004/42/EC): 2004/42/IIB(b)(250)250 The EU limit value for this product (product category: IIB.b) in ready for use form is max 250 g/litre of VOC. The VOC value of this product in ready to use form is max. 250 g/l. Important remarks: Polyester materials have a limited shelf life. Store in a cool place, and use within 12 months for best results. Through-sanded areas must be primed with an etch primer according to substrate properties. Standox Spray Filler U1100 must not be applied to 1K Primer, Etch Primer or solvent sensitive substrates. Standox Spray Filler U1100 must be overcoated with Standox Filler before topcoating. For optimum quality work a film thickness of 150 micron should remain on the substrate after sanding. Use at temperatures above +15 C. PE Hardener contains organic peroxide and is corrosive. If PE Hardener comes in contact with the skin, wipe off immediately and wash with soap and water. After eye contact irrigate copiously with a 2% aqueous sodium carbonate solution or water and seek medical advice. For professional use only! The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose. The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved. The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed. We may modify and/ or discontinue operation of all or portions of this Information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. SX-GB Version 07 Axalta Coating Systems Germany GmbH Christbusch Wuppertal 231 3/3 Germany

64 Standox Rapid Spachtel U1080 Rapid Stopper U1080 Multi-purpose stopper coarse or fine Also useable as a fine stopper Good infrared drying Good vertical stability Easy to sand Excellent adhesion on all substrates Technical Description: Mix with 2-3% Standox Hardener paste U1120 Potlife 4-5 min / C Air dry min / C Force drying possible Dry sand P80 - P240 An Axalta Coating Systems Brand SX-GB Version /3

65 Standox Rapid Spachtel U1080 Substrate: Application: Through-hardened sanded paintwork Bare steel, UP-GF and Aluminium, sanded 2-3% Standox Hardener paste U1120 Potlife 4-5 min / C Galvanized substrate, sanded Through-hardened Standox Fillers, sanded Apply stopper Air dry min / C Pretreatment / Cleaning: For substrate preparation information see Standox Painting System S1. Use air fed respirator. Refer to relevant Health and Safety Data sheets. Short wave 2-3 min (see Standox Painting System S10) Coarse sand P80 - P120 Fine sand P180 - P240 Standox Filler, Primer and Primer Surfacer SX-GB Version /3

66 Standox Rapid Spachtel U1080 Flash point: 33 C / 91.4 F Cleaning of equipment: Clean after use with Standox Cleaning Thinner. Specific Gravity: 1.82 g/cm³ Solid Content (without thinner added): 85.9 Weight % 73.3 Volume % Important remarks: Polyester materials have a limited shelf life. Store in a cool place and use within 12 months for best results. Do not apply to Etch Primer, 1K Filler, TPA substrates and soft old paintwork. VOC (2004/42/EC): 2004/42/IIB(b)(250)150 The EU limit value for this product (product category: IIB.b) in ready for use form is max 250 g/litre of VOC. The VOC content of this product in ready for use form is max. 150 g/l. Do not apply at temperatures below +5 C. Mix the 2-3% Standox Hardener paste U1120 well with the stopper. Do not add more as this may cause staining of the topcoat finish. Using the Standox Hardener paste U1120 Blue prolongs potlife by 2 min. Hardener paste contains organic peroxide and is corrosive. If Hardener paste comes in contact with the skin, wipe off immediately and wash with soap and water. After eye contact irrigate copiously with a 2% aqueous sodium carbonate solution or water and seek medical advice. For professional use only! The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose. The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved. The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed. We may modify and/ or discontinue operation of all or portions of this Information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. SX-GB Version 05 Axalta Coating Systems Germany GmbH Christbusch Wuppertal 240 3/3 Germany

67 Standox Soft-Spachtel U1090 Soft Stopper U1090 Multi-purpose stopper coarse or fine Also useable as a fine stopper Especially suitable for infrared drying Good vertical stability Easy to sand Excellent adhesion on all substrates Technical Description: Mix with 2-3% Standox Hardener paste U1120 Potlife 4-5 min / C Force drying possible Air dry min / C Dry sand P80 - P240 An Axalta Coating Systems Brand SX-GB Version /3

68 Standox Soft-Spachtel U1090 Substrate: Application: Through-hardened sanded paintwork Bare steel, UP-GF and Aluminium, sanded 2-3% Standox Hardener paste U1120 Potlife 4-5 min / C Galvanized substrate, sanded Through-hardened Standox Fillers, sanded Apply stopper Air dry min / C Pretreatment / Cleaning: For substrate preparation information see Standox Painting System S1. Use air fed respirator. Refer to relevant Health and Safety Data sheets. Short wave 2-3 min (see Standox Painting System S10) Coarse sand P80 - P120 Fine sand P180 - P240 Standox Filler, Primer and Primer Surfacer SX-GB Version /3

69 Standox Soft-Spachtel U1090 Flash point: 32 C / 89.6 F Cleaning of equipment: Clean after use with Standox Cleaning Thinner. Specific Gravity: 1.87 g/cm³ Solid Content (without thinner added): 86.8 Weight % 74.6 Volume % Important remarks: Polyester materials have a limited shelf life. Store in a cool place and use within 12 months for best results. Do not apply to Etch Primer, 1K Filler, TPA substrates and soft old paintwork. VOC (2004/42/EC): 2004/42/IIB(b)(250)150 The EU limit value for this product (product category: IIB.b) in ready for use form is max 250 g/litre of VOC. The VOC content of this product in ready for use form is max. 150 g/l. Do not apply at temperatures below +5 C. Mix the 2-3% Standox Hardener paste U1120 well with the stopper. Do not add more as this may cause staining of the topcoat finish. Using the Standox Hardener paste U1120 Blue prolongs potlife by 2 min. Hardener paste contains organic peroxide and is corrosive. If Hardener paste comes in contact with the skin, wipe off immediately and wash with soap and water. After eye contact irrigate copiously with a 2% aqueous sodium carbonate solution or water and seek medical advice. For professional use only! The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose. The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved. The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed. We may modify and/ or discontinue operation of all or portions of this Information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. SX-GB Version 04 Axalta Coating Systems Germany GmbH Christbusch Wuppertal 212 3/3 Germany

70 Standox Reaktiv-Haftprimer U3100 Etching Adhesion Primer U3100 Acid primer Excellent adhesion For 3-stage systems Outstanding corrosion protection Part of OEM approved refinish systems Technical Description: Mix 1:1 with Standox Etching Adhesion Activator U3110 Potlife 8 h / C 2 spray passes = 8 micron Flash off min / C An Axalta Coating Systems Brand SX-GB Version /3

71 Standox Reaktiv-Haftprimer U3100 Substrate: Application: Bare metal, sanded Aluminium, sanded Galvanised metal, sanded 1:1 with Standox Etching Adhesion Activator U3110 Potlife 8 h / C Through-hardened sanded paintwork Pretreatment / Cleaning: For substrate preparation information see Standox Painting System S1. Compliant mm bar inlet pressure 2 = 8-10 micron HVLP mm 0.7 bar atomization pressure 2 = 8-10 micron min / C Use air fed respirator. Refer to relevant Health and Safety Data Sheets. Standox Filler SX-GB Version /3

72 Standox Reaktiv-Haftprimer U3100 Flash point: 24 C / 75.2 F Cleaning of equipment: Clean after use with Standox Cleaning Thinner. Specific Gravity: 0.98 g/cm³ Solid Content (without thinner added): 28.8 Weight % 16.4 Volume % Important remarks: Standox Etching Adhesion Primer U3100 must be applied in combination with Standox Filler in a 3-stage system. Do not overcoat with PE, EP, Standohyd and Standoblue products. VOC (2004/42/EC): 2004/42/IIB(c)(780)780 The EU limit value for this product (productcategory IIB.c) in ready to use form is max 780 g/l VOC. The VOC content of this product in ready for use form is max. 780 g/l. Clean spraygun after use Only use plastic or inner coated metal cans. Theoretical Coverage: 9,9 m²/l at 8 micron dry film thickness For professional use only. The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose. The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved. The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed. We may modify and/ or discontinue operation of all or portions of this Information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. SX-GB Version 07 Axalta Coating Systems Germany GmbH Christbusch Wuppertal 312 3/3 Germany

73 Standox 1K-Füllprimer U3010 1K Primer Filler U3010 1K acid primer Corrosion protection Certificate for welding Technical Description: Suitable as a primer 1 spray coat Overcoat with Standox Filler after min / C flash off An Axalta Coating Systems Brand SX-GB Version /3

74 Standox 1K-Füllprimer U3010 Substrate: Application: Primer Bare metal, sanded Aluminium, sanded Galvanised metal, sanded 50% Standox 2K / VOC Thinner s / DIN 4 mm / 20 C s / ISO 4 mm / 20 C Small through-sanded areas in old paintwork and primed replacement panels Compliant mm bar inlet pressure 1 = 15 micron Pretreatment / Cleaning: For substrate preparation information see Standox Painting System S1. HVLP mm 0.7 bar atomization pressure 1 = 15 micron min / C Standox Filler Use air fed respirator. Refer to relevant Health and Safety Data sheets. SX-GB Version /3

75 Standox 1K-Füllprimer U3010 Flashpoint: 24 C / 75.2 F Cleaning of equipment: Clean after use with Standox Cleaning Thinner. Specific Gravity: g/cm³ Solid Content (without thinner added): Weight % Volume % VOC (2004/42/EC): 2004/42/IIB(c)(780)760 The EU limit value for this product (product category: IIB.c) in ready for use form is max 780 g/l of VOC. The VOC content of this product in ready for use form is max. 760 g/l. Important remarks: After sanding Standox 1K Primer Filler U3010 has to be covered completely with Standox Filler. Do not overcoat with PE or EP products. Standox 1K Primer Filler U3010 gives steel 3 months weather resistance, if a dry film thickness of 50 micron is obtained in several spray passes. Do not dry sand. IR drying possible 5 min 50% performance Theoretical Coverage: m²/l at 40 micron dry film thickness For professional use only! The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose. The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved. The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed. We may modify and/ or discontinue operation of all or portions of this Information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. SX-GB Version 05 Axalta Coating Systems Germany GmbH Christbusch Wuppertal 413 3/3 Germany

76 Standox SprayMax 1K-Füllprimer U3010 1K Primer Filler U3010 1K acid primer Corrosion protection Welding certificate Technical Description: Suitable as a primer 1 spray pass Overcoat with Standox Filler after min / C flash off Suitable as a primer filler for small areas 2-3 spray passes Dry, denib slightly and repaint An Axalta Coating Systems Brand SX-GB Version /3

77 Standox SprayMax 1K-Füllprimer U3010 Substrate: Small through-sanded areas in old paintwork and primed replacement panels Application: Spot Repair Primer: Pretreatment / Cleaning: For substrate preparation information see Standox Painting System S1. 1 = 15 micron min / C Use air fed respirator. Refer to relevant Health and Safety Data Sheets. Standox Filler Primer Filler: 2-3 = micron min / C depending on film thickness After 45 min / C denib lightly or after 90 min / C wet sand P800 - P1000 Standocryl VOC Topcoat or Standohyd / Standoblue Basecoat with Standocryl VOC Clears SX-GB Version /3

78 Standox SprayMax 1K-Füllprimer U3010 Flash point: -1 C / 30.2 F Important remarks: We recommend a 3-stage system on galvanised substrates and aluminium. Specific Gravity: 0,82 g/cm³ In a 3-stage system Standox 1K Primer Filler U3010 has to be covered completely with Standox Filler even after sanding. Solid Content Do not overcoat with PE or EP products. (without thinner added): 16.8 Weight % The use of Spray Max 1K Primer Filler U3010 as a sandthrough primer filler is limited only to very small areas, Volume % e.g. no greater than Spray Max can lid. VOC (2004/42/EC): 2004/42/IIB(e)(840)660 The EU limit value for this product (productcategory IIB.e) in ready to use form is max 840g/ltr. The VOC content of this product in ready for use form is max. 660 g/l. Standox 1K Primer Filler U3010 gives steel 3 months weather resistance with a minimum dry film thickness of 50 micron. Do not dry sand. IR drying possible 5 min 50% performance After use, hold aerosol can upside down and spray briefly to clean nozzle. In countries without VOC legislation Standox Basecoat / Standocryl 2K Topcoat / Standocryl 2K Topcoat NEW can be used as well. For professional use only! The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose. The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved. The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed. We may modify and/ or discontinue operation of all or portions of this Information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. SX-GB Version 07 Axalta Coating Systems Germany GmbH Christbusch Wuppertal /3 Germany

79 Standox SprayMax Reaktiv-Haftprimer U3100 Etching Adhesion Primer U3100 2K acid primer Excellent adhesion For 3-stage systems Outstanding corrosion protection Convenient for local repairs Long potlife Technical Description: Potlife 4-5 days / C 2 spray passes Flash off 5 min between coats Recoatable after minutes An Axalta Coating Systems Brand SX-GB Version /3

80 Standox SprayMax Reaktiv-Haftprimer U3100 Substrate: Application: Through-hardened sanded paintwork Bare metal, sanded Galvanised metal, sanded Aluminium, sanded Sand and clean surface repair area thoroughly. Pretreatment / Cleaning: Two-component product: Shake well the aerosol can. Remove red button from can cap and attach it to the hardener injection valve on bottom of the can. Press to inject hardener. Shake well for at least 2 min. Ready to spray Potlife 4-5 days / C Shake well again prior to each use. 2 coats = 8-10 micron For substrate preparation information see Standox Painting System S1. 5 min / C intermediate flash off between coats Use air fed respirator. Refer to relevant Health and Safety Data Sheets. Air dry min / C Standox Filler SX-GB Version /3

81 Standox SprayMax Reaktiv-Haftprimer U3100 Flash point: -1 C / 30.2 F Specific Gravity: 0.76 g/cm³ Important remarks: Do not use Standox SprayMax Etching Adhesion Primer U3100 on thermoplastic paintwork. Keep a distance of cm to the object. Solid Content (without thinner added): 8.2 Weight % 3.6 Volume % VOC (2004/42/EC): 2004/42/IIB(e)(840)710 The EU limit value for this product (productcategory IIB.e) in ready to use form is max 840g/ltr. The VOC content of this product in ready for use form is max. 710 g/l. Use at temperatures above 15 C. Do not overcoat with PE, EP, Standohyd and Standoblue products. After use, hold aerosol can upside down and spray briefly to clean nozzle. For professional use only! The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose. The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved. The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed. We may modify and/ or discontinue operation of all or portions of this Information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. SX-GB Axalta Coating Systems Germany GmbH Christbusch 25 Version / Wuppertal Germany

82 Standox EP-Grundierfüller U7200 EP Primer Surfacer U7200 Epoxy-based universal primer surfacer Good isolating properties Good infrared drying Primer for Standox Spray Filler U1100 on zinc Good weather-resistant properties Technical Description: Mix 3:1 with Standox EP Hardener U7210 Potlife 3 h / C 2-3 spray coats Force drying possible Air dry overnight / C An Axalta Coating Systems Brand SX-GB Version 01 MB 932 1/3

83 Standox EP-Grundierfüller U7200 Substrate: Through-hardened sanded paintwork Bare metal, sanded Application: Sanding filler 3:1 with Standox EP Hardener U7210 Potlife 3 h / C Galvanised metal, sanded Aluminium, sanded Standox Polyester substrates, sanded UP-GF, sanded Substrates must be carefully sanded and cleaned. Pretreatment / Cleaning: 25% Standox VOC Thinner or 20% Standox 2K Thinners s / DIN 4mm / 20 C s / ISO 4mm / 20 C Compliant mm bar inlet pressure 2-3 = micron HVLP mm 0.7 bar atomization pressure 2-3 = micron Intermediate and final flash-off 5-10 min / C For substrate preparation information see Standox Painting System S1 Use air fed respirator. Refer to relevant Health and Safety Data Sheets. Air dry overnight / C or min. / C panel temperature depending on film thickness Short wave 3-5 min / 50% performance afterwards min / 100% performance P Orbital sander P800 - P1000 Standocryl VOC Topcoat or Standohyd Basecoat with Standocryl VOC Clears SX-GB Version 01 MB 932 2/3

84 Standox EP-Grundierfüller U7200 Flashpoint: 28 C / 82.4 F Cleaning of equipment: Clean after use with Standox Cleaning Thinner. Specific Gravity: 1.62 g/cm³ Important remarks: Solid Content (without thinner added): 74.1 Weight % 53.7 Volume % Do not use Standox EP Primer Surfacer U7200 on acid etch primers. Standox EP Primer Surfacer U7200 gives steel 3 months weather resistance at a dry film thickness of 50 micron. VOC (2004/42/EC): 2004/42/IIB(c)(540)540 The EU limit value for this product (productcategory IIB.c) in ready to use form is max 540 g/l VOC. The VOC content of this product in ready for use form is max. 540 g/l. Theoretical Coverage: 8.1 m²/l at 55 micron dry film thickness If Standox EP Primer Surfacer U7200 is used as primer for galvanised metal, it has to be dried 30 min/60-65 C panel temperature or air dry overnight/18-22 C and lightly denibbed before overcoating with Standox PE Spray Filler U1100. Standox EP Primer Surfacer U7200 can be mixed with max. 10% Standocryl VOC Topcoat. Drying and sanding properties will change. In countries without VOC legislation Standox Basecoat / Standocryl 2K Topcoat / Standocryl 2K Topcoat NEW can be used as well. For professional use only! The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose. The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved. The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed. We may modify and/ or discontinue operation of all or portions of this Information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. SX-GB Version 01 MB 932 Axalta Coating Systems Germany GmbH Christbusch Wuppertal 3/3 Germany

85 Standox SprayMax EP-Grundierfüller U7200 EP Primer Surfacer U7200 Epoxy-based universal primer surfacer in a two-component spray can Suitable as an isolator for old TPA substrates Good isolating properties Primer for Standox Spray Filler U1100 on zinc Good weather-resistant properties Technical Description: Potlife 72 h / C 2-3 spray coats Force drying possible Air dry overnight / C An Axalta Coating Systems Brand SX-GB Version 04 MB /3

86 Standox SprayMax EP-Grundierfüller U7200 Substrate: Through-hardened sanded paintwork Application: Sanding filler Bare metal, sanded Galvanised metal, sanded Aluminium, sanded Two-component product: Remove red button from can cap and attach it to the hardener injection valve on bottom of the can. Press to inject hardener. Shake well for at least 2 min. Standox Polyester substrates, sanded UP-GF, sanded Ready to spray Potlife 72 h / C Substrates must be carefully sanded and cleaned. 2-3 = micron 5-10 min / C flash off between coats Pretreatment / Cleaning: For substrate preparation information see Standox Painting System S1 Use air fed respirator. Refer to relevant Health and Safety Data Sheets. Air dry overnight / C or min. / C panel temperature depending on film thickness Short wave 3 min / 50% performance afterwards 12 min / 100% performance P400 - P500 Orbital sander, dry P800 - P1000 Standocryl VOC Topcoat or Standohyd Basecoat with Standocryl VOC Clears SX-GB Version 04 MB /3

87 Standox SprayMax EP-Grundierfüller U7200 Flashpoint: -4 C / 24.8 F Specific Gravity: 0.94 g/cm³ Important remarks: Do not use Standox SprayMax EP Primer Surfacer U7200 on acid etch primers. Keep a distance of cm to the object Solid Content (without thinner added): 34.0 Weight % 15.4 Volume % VOC (2004/42/EC): 2004/42/IIB(e)(840)650 The EU limit value for this product (productcategory IIB.e) in ready to use form is max 840 g/l VOC. The VOC content of this product in ready for use form is max. 650 g/l. Standox SprayMax EP Primer Surfacer U7200 gives steel 3 months weather resistance at a dry film thickness of 50 micron. If Standox SprayMax EP Primer Surfacer U7200 is used as a primer on galvanized metal Standox Spray Filler U1100 can only be applied on the through-dried and slightly denibbed Standox SprayMax Primer Surfacer U7200 after 30 min / C panel temperature or airdry overnight / C or IR drying. After use, hold aerosol can upside down and spray briefly to clean nozzle. Use at temperatures above 15 C. In countries without VOC legislation Standox Basecoat / Standocryl 2K Topcoat / Standocryl 2K Topcoat NEW can be used as well. For professional use only! The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose. The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved. The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed. We may modify and/ or discontinue operation of all or portions of this Information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. SX-GB Version 04 MB /3 Axalta Coating Systems Germany GmbH Christbusch Wuppertal Germany

88 Standox VOC-Nonstop-Füllprimer U7550 VOC Nonstop Primer Filler U7550 VOC compliant Multi-purpose product Isolating filler also for critical substrates Excellent hold out Technical Description: Mix 5:1 with all Standox VOC Hardeners or Mix 3:1 with all Standox HS Hardeners Force drying possible Air dry overnight / C Dry sand and wet sand An Axalta Coating Systems Brand SX-GB Version 07 MB 531 1/4

89 Standox VOC-Nonstop-Füllprimer U7550 Substrate: Through-hardened sanded paintwork Standox PE Products, sanded Thermoplastic coatings (TPA) and sensitive substrates Well cleaned and fine or unsanded OEM Primer or EDP Only genuine OEM factory supplied parts in KTL or factory E-coat have the advantage that no sanding is required prior to the application of Standox VOC Nonstop Primer Filler U7550. Bare metal substrates must be pre-primed with acid primer. Application: Sanding Filler 5:1 with all Standox VOC Hardeners Potlife min / C 15-20% Standox VOC Thinner s / DIN 4mm / 20 C s / ISO 4mm / 20 C Compliant mm bar inlet pressure 2-3 = micron Pretreatment / Cleaning: For substrate preparation information see Standox Painting System S1 Use air fed respirator. Refer to relevant Health and Safety Data Sheets. 3:1 with Standox HS Hardeners 10-15% Standox 2K Thinner / Standox VOC Thinner s / DIN 4mm / 20 C s / ISO 4mm / 20 C HVLP mm 0.7 bar atomization pressure 2-3 = micron Air dry overnight / C or min. / C panel temperature P800 P400 - P500 Orbital sander Standocryl VOC Topcoat or Standohyd / Standoblue Basecoat with Standocryl VOC Clears Flash off 5-10 min / C before oven- or infrared drying SX-GB Version 07 MB 531 2/4

90 Standox VOC-Nonstop-Füllprimer U7550 Substrate: Application: Isolating Filler Through-hardened sanded paintwork Standox PE Products, sanded Thermoplastic coatings (TPA) and sensitive substrates Bare metal substrates must be pre-primed with acid primer. Pretreatment / Cleaning: For substrate preparation information see Standox Painting System S1 Use air fed respirator. Refer to relevant Health and Safety Data Sheets. 5:1 with all Standox VOC Hardeners Potlife 60 min / C 30% Standox VOC Thinner s / DIN 4mm / 20 C s / ISO 4mm / 20 C Compliant mm bar inlet pressure 3-4 = micron HVLP mm 0.7 bar atomization pressure 3-4 = micron Air dry overnight / C or min. / C panel temperature 3:1 with Standox HS Hardeners 20-23% Standox VOC Thinner s / DIN 4mm / 20 C s / ISO 4mm / 20 C Flash off 5-10 min / C before oven- or infrared drying Do not sand through the isolating filler. Sand-through areas must be reprimed. P800 P400 - P500 Orbital sander Standocryl VOC Topcoat or Standohyd / Standoblue Basecoat with Standocryl VOC Clears SX-GB Version 07 MB 531 3/4

91 Standox VOC-Nonstop-Füllprimer U7550 Flashpoint: 24 C / 75 F Cleaning of equipment: Clean after use with Standox Cleaning Thinner. Specific Gravity: g/cm³ Important remarks: Apply spray passes with care. Solid Content (without thinner added): Weight % Volume % Do not use infrared drying for substrates not resistant to solvents and TPA. The filler can be mixed with max. 15% Standocryl VOC Topcoat. Drying and sanding properties will change. VOC (2004/42/EC): 2004/42/IIB(c)(540)540 The EU limit value for this product (productcategory IIB.c) in ready to use form is max 540 g/l VOC. The VOC content of this product in ready for use form is max. 540 g/l. In countries without VOC legislation Standox Basecoat / Standocryl 2K Topcoat can be used for overcoating as well. In a wet-on-wet process flash-off times can be reduced to min / micron if overcoated with Standox Basecoat / Standocryl 2K Topcoat / Standocryl 2K Topcoat NEW / Standocryl VOC Topcoat. Theoretical Coverage: Sanding filler: 4.8 m²/l at 80 micron dry film thickness 2K Paints react with moisture. Therefore all equipment must be kept moisture free. Ready to use paint materials containing isocyanates can cause irritation of the mucous membranes - and of the respiratory organs, in particular - and cause hypersensitive reactions. There is a risk of hypersensitization if the vapour or spray mist is inhaled. When using materials containing isocyanates, all precautions relating to the handling of solvents should be carefully followed. In particular, care should be taken not to inhale spray mist or vapour. Asthma sufferers, those with allergies and anyone with a history of respiratory complaints must not be asked to work with products containing isocyanates. For professional use only! The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose. The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved. The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed. We may modify and/ or discontinue operation of all or portions of this Information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. SX-GB Version 07 MB 531 Axalta Coating Systems Germany GmbH Christbusch Wuppertal 4/4 Germany

92 Standox VOC-System-Füller U7540 VOC System Filler U7540 VOC compliant Good vertical stability Good filling properties Easy to sand Excellent tension Good isolating properties Technical Description: Mix 7:1 with all Standox VOC Hardeners or Mix 4:1 with all Standox HS Hardeners Force drying possible Air dry overnight / C An Axalta Coating Systems Brand SX-GB Version /4

93 Standox VOC-System-Füller U7540 Substrate: Application: VOC System Through-hardened sanded paintwork, except TPA OEM Primer or EDP, sanded Standox PE Products, sanded UP-GF, sanded Bare metal substrates must be pre-primed with Standox Acid Primer. Pretreatment / Cleaning: For substrate preparation information see Standox Painting System S1. Use air fed respirator. Refer to relevant Health and Safety Data Sheets. 7:1 with all Standox VOC Hardeners Potlife min / C 10% Standox VOC Thinner s / DIN 4mm / 20 C s / ISO 4 mm / 20 C Compliant mm bar inlet pressure 2-3 = max. 250 micron HVLP mm 0.7 bar atomization pressure 2-3 = max. 250 micron Air dry overnight / C or min. / C panel temperature Short wave min (see Standox Painting System S10) P800 Flash off 5-15 min / C before oven- or infrared drying P400 - P500 Orbital sander Standocryl VOC Topcoat or Standohyd / Standoblue Basecoat with Standocryl VOC Clears SX-GB Version /4

94 Standox VOC-System-Füller U7540 Substrate: Application: HS System Through-hardened sanded paintwork, except TPA OEM Primer or EDP, sanded Standox PE Products, sanded UP-GF, sanded Bare metal substrates must be pre-primed with Standox Acid Primer. Pretreatment / Cleaning: For substrate preparation information see Standox Painting System S1. 4:1 with all Standox HS Hardeners Potlife min / C If necessary 5-10% Standox 2K Thinner s / DIN 4mm / 20 C s / ISO 4 mm / 20 C Compliant mm bar inlet pressure 2-3 = max. 250 micron HVLP mm 0.7 bar atomization pressure 2-3 = max. 250 micron Air dry overnight / C or min. / C panel temperature Use air fed respirator. Refer to relevant Health and Safety Data Sheets. Short wave min (see Standox Painting System S10) P800 Flash off 5-15 min / C before oven- or infrared drying P400 - P500 Orbital sander Standocryl VOC Topcoat or Standohyd / Standoblue Basecoat with Standocryl VOC Clears SX-GB Version /4

95 Standox VOC-System-Füller U7540 Flash point: C / F Cleaning of equipment: Clean after use with Standox Cleaning Thinner. Specific Gravity: g/cm³ Solid Content (without thinner added): Volume % Important remarks: For better control of the sanding process, spray the filler and allow to flash off. Spray a thin coat of Control Black as a guide coat Weight % The filler can be mixed with max. 15% Standocryl VOC Topcoat. Drying and sanding properties will change. VOC (2004/42/EC): 2004/42/IIB(c)(540)540 The EU limit value for this product (productcategory IIB.c) in ready to use form is max 540 g/l VOC. The VOC content of this product in ready for use form is max. 540 g/l. For film thicknesses of more than 150 micron air dry overnight / C or 40 min / C panel temperature. In countries without VOC legislation Standox Basecoat / Standocryl 2K Topcoat / Standocryl 2K Topcoat NEW can be used as well. Theoretical Coverage: m²/l at 80 micron dry film thickness 2K Paints react with moisture. Therefore all equipment must be kept moisture free. Ready to use paint materials containing isocyanates can cause irritation of the mucous membranes - and of the respiratory organs, in particular - and cause hypersensitive reactions. There is a risk of hypersensitization if the vapour or spray mist is inhaled. When using materials containing isocyanates, all precautions relating to the handling of solvents should be carefully followed. In particular, care should be taken not to inhale spray mist or vapour. Asthma sufferers, those with allergies and anyone with a history of respiratory complaints must not be asked to work with products containing isocyanates. For professional use only. The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose. The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved. The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed. We may modify and/ or discontinue operation of all or portions of this Information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. SX-GB Version 04 Axalta Coating Systems Germany GmbH Christbusch Wuppertal 539 4/4 Germany

96 Standoflash UV-Füller U7100 UV Filler U7100 2K primer surfacer for micro repair One visit application Dries in less than 30 seconds Share of organic solvents < 1% Excellent gloss holdout Semi-transparent filler Technical Description: Mix 10:1 by weight / 9:1 by volume with Standoflash UV Additive U Spray passes Drying with Standoflash UV Lamp VISIT UV Flash Dry 15/700 only Dry and wet sand An Axalta Coating Systems Brand SX-GB Version /4

97 Standoflash UV-Füller U7100 Substrate: Bare metal, sanded Through-hardened sanded paintwork Standox PE substrates, sanded Aluminium, sanded Galvanised metal, sanded UP-GF, sanded Primed plastic parts Application: 2K Primer Surfacer 10:1 by weight 9:1 by volume with Standoflash UV Additive U7110 Potlife: 7 days / C Substrates must be carefully sanded and cleaned. In case of new parts with electro dip coating (anodic / cathodic dip coating) the coating has to be removed completely by sanding in the repair area. Pretreatment / Cleaning: For substrate preparation information see Standox Painting System S1. HVLP mm SATA Mini-Jet / DeVilbiss SRI 0.7 bar atomization pressure = micron 0 min Wipe off overspray before drying with a clean lint-free cloth. Standoflash UV Lamp VISIT UV Flash Dry 15/700 2 x 10 flashes per repair area = approx. 30 s P400 - P500 Use air fed respirator. Refer to relevant Health and Safety Data sheets. With plastic substrates allow for 1-2 min cooling down after 10 flashes. P600 - P800 Standocryl VOC Topcoat or Standohyd / Standoblue Basecoat with Standocryl VOC Clear SX-GB Version /4

98 Standoflash UV-Füller U7100 Health and Safety: The UV-light-curing Standoflash UV Filler U7100 itself is in principle not considered to be unhealthy. However, when applying this primer surfacer, the same protective and safety measures are to be taken as for standard paint materials. Handling UV radiation sources, however, requires particular care. Dangers can only be avoided if a licensed UV drying equipment is used in the proper way. For this reason the following notes are to be observed when using UV technology: Operating the equipment: Skin and eye protection: Working area: Maximum exposure level: Strictly follow the operating instructions of the manufacturer for the UV drying equipment VISIT UV Flash Dry 15/700. To protect the skin and the eyes from blinding and UV radiation the following measures are to be taken: Wear a UV protective face mask: 3M Speed Glas 9002 V Wear UV light absorbing / reflecting gloves: Reitz-Mappa Rubber Gloves Wear UV light absorbing / reflecting clothing: Wibeco Overall silver No unprotected personnel should be within a distance of 5 metres from the lamp during use. To rule out possible misuse, we recommend setting up a separate ventilated work area. Measurements performed in-house showed that when the UV Flash Dry device 15/700 from VISIT is used in the proper way (flexible seal lying on completely flat surface, see operating instructions), UV radiation generally remains below the permissible daily dose of 30 J/m² stipulated by the ICNIRP, provided the output of 3000 pulses per 8 hour working day is not exceeded. Please note that the reflector is equipped with a glare shield which must be intact at the time of usage of the reflector. Measurement of the UV radiation on-site is strictly required if the number of pulses exceeds 3000 pulses per 8 hour working day. Please contact the respective Institution for Statutory Accident Insurance and Prevention in this case. Training of personnel: UV drying equipment may only be used by instructed and trained personnel. In accordance with the legal requirements, the bodyshop should display operating instructions describing the use of the device. SX-GB Version /4

99 Standoflash UV-Füller U7100 Flash point: 98 C / F Cleaning of equipment: Clean after use with Standox Cleaning Thinner. Specific Gravity: 1.35 g/cm³ Solid Content Important remarks: Masking paper: (without thinner added): Masking paper must be removed completely before 98.8 Weight % drying by pulsed UV lamp Volume % Filler cannot be tinted. SATA MiniJet / DeVilbiss SRI should be equipped with light-proof gravity cups. VOC (2004/42/EC): Standoflash UV Filler U7100 can only be dried with 2004/42/IIB(c)(540)50 Standoflash UV Lamp VISIT UV Flash Dry 15/700 The EU limit value for this product (product Before recoating with itself after UV drying, with/without category: IIB.c) in ready for use form is sanding, the surface must be pre-cleaned with Standox max 540 g/l of VOC. The VOC content of Silicone Remover. this product in ready for use form is max. Follow all safety instructions. 50 g/l. Do not operate equipment before reading and understanding the manufacturer's user manual and safety instructions. Theoretical Stored material should not be exposed to light. Coverage: In countries without VOC legislation Standox Basecoat / Standocryl 2K Topcoat / Standocryl 2K Topcoat NEW can be used as well m²/l at 60 micron dry film thickness Vehicle area for repair: Vehicle areas where fuel vapour may occur, e.g. tank caps, may not be repaired. 2K Paints react with moisture. Therefore all equipment must be kept moisture free. Ready to use paint materials containing isocyanates can cause irritation of the mucous membranes - and of the respiratory organs, in particular - and cause hypersensitive reactions. There is a risk of hypersensitization if the vapour or spray mist is inhaled. When using materials containing isocyanates, all precautions relating to the handling of solvents should be carefully followed. In particular, care should be taken not to inhale spray mist or vapour. Asthma sufferers, those with allergies and anyone with a history of respiratory complaints must not be asked to work with products containing isocyanates. For professional use only! The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose. The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved. The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed. We may modify and/ or discontinue operation of all or portions of this Information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. SX-GB Version 09 Axalta Coating Systems Germany GmbH Christbusch Wuppertal Germany 450 4/4

100 Standox VOC-Xtra-Füller U7560 VOC Xtra Filler U7560 VOC compliant sanding surfacer Good vertical stability Very good filling properties Optimum surface to enhance topcoat appearance Excellent drying Very robust application and drying properties One visit application for new panels Technical Description: Mix 5:1 with all Standox VOC Hardeners Force drying possible Air dry 2-3 h / C depending on film thickness An Axalta Coating Systems Brand SX-GB Version /3

101 Standox VOC-Xtra-Füller U7560 Substrate: Application: VOC System Through-hardened sanded paintwork, except TPA Unsanded & Cleaned OEM Primer or EDP Standox PE Products, sanded 5:1 with all Standox VOC Hardeners potlife min /18-22 C 5-10% Standox VOC Thinner s / DIN 4 mm / 20 C s / ISO 5 mm / 20 C UP-GF, sanded Bare metal substrates must be pre-primed with Standox Acid Primer or thoroughly dried Standox EP Primer Surfacer U7200. Compliant mm bar inlet pressure 2-4 = max. 250 micron HVLP mm 0.7 bar atomization pressure 2-4 = max. 250 micron Pretreatment / Cleaning: For substrate preparation information see Standox Painting System S1. Use air fed respirator. Refer to relevant Health and Safety Data sheets. Flash off 5-10 min / C before oven- or infrared drying Low film builds: microns: air dry 2-3h / C or min / C panel temperature Higher film builds: max. 250 microns: air dry overnight / C or min / C panel temperature Short wave 2 min 50% power + 8 min 100% power (see Standox Painting System S10) P800 P400 - P600 Orbital sander Standocryl VOC Topcoat or Standohyd / Standoblue Basecoat with Standocryl VOC Clears SX-GB Version /3

102 Standox VOC-Xtra-Füller U7560 Flash point: C / F Cleaning of equipment: Clean after use with Standox Cleaning Thinner. Specific Gravity: g/cm³ Solid Content (without thinner added): Weight % Volume % VOC (2004/42/EC): 2004/42/IIB(c)(540)540 The EU limit value for this product (product category: IIB.c) in ready for use form is max 540 g/l of VOC. The VOC value of this product in ready to use form is max. 540 g/l. Theoretical Coverage: 8.3 m²/l at 60 micron dry film thickness Important remarks: We recommend to put can on mixing machine Standox VOC X Hardeners can also be used in mixing ratio 5:1 plus 10-15% Standox VOC Thinner. When used over acid primer the filler must be either airdried overnight or forcedried. For better control of the sanding process, spray the filler and allow to flash off. Spray a thin coat of Control Black as a guide coat. The Filler can be mixed with max. 15% Standocryl VOC Topcoat. Drying and sanding properties will change. This product is intended for the refinishing of passenger cars. Can be applied in 2 full consecutive coats without intermediate flash-off. Recommended for new panels where limited film build is required e.g: microns. Standox Plasticiser can be added up to 15%. Mixing ratio will change to 4:1 plus 10% Standox VOC Thinner. In countries without VOC legislation Standox Basecoat / Standocryl 2K Topcoat / Standocryl 2K Topcoat NEW can be used as well. 2K Paints react with moisture. Therefore all equipment must be kept moisture free. Ready to use paint materials containing isocyanates can cause irritation of the mucous membranes - and of the respiratory organs, in particular - and cause hypersensitive reactions. There is a risk of hypersensitization if the vapour or spray mist is inhaled. When using materials containing isocyanates, all precautions relating to the handling of solvents should be carefully followed. In particular, care should be taken not to inhale spray mist or vapour. Asthma sufferers, those with allergies and anyone with a history of respiratory complaints must not be asked to work with products containing isocyanates. For professional use only! The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose. The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved. The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed. We may modify and/ or discontinue operation of all or portions of this Information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. SX-GB Version /3 Axalta Coating Systems Germany GmbH Christbusch Wuppertal Germany

103 Standohyd Basecoat Water-thinnable Easy to blend in Good opacity High coverage One visit application Outstanding colour accuracy Contains less than 10% organic solvent Solid, metallic, pearl colours Technical Description: Thin with Standox Demineralized Water Use mixing stick 1 working spray pass An Axalta Coating Systems Brand SX-GB Version /3

104 Standohyd Basecoat Substrate: Application: Standox Filler Through-hardened sanded paintwork Standoflex 2K Plastic Primer Surfacer U3200 approx. 5-10% Standox Demineralized Water s / DIN 4 mm / 20 C s / ISO 4 mm / 20 C Do not forget cleaning! Pretreatment / Cleaning: For substrate preparation information see Standox Painting System S1. Compliant mm bar inlet pressure = micron HVLP mm 0.7 bar atomization pressure = micron Final flash off until matt Use air fed respirator. Refer to relevant Health and Safety Data sheets. Standocryl VOC Clears For effect colours 1 additional light coat is possible to control metallic effect. Flash off time can be reduced by - Using air blower - Spray booth blower system - Infrared drying - Increasing spray booth temperature SX-GB Version /3

105 Standohyd Basecoat Flash point: C / F Cleaning of equipment: Clean after use with Standox Cleaning Thinner. Specific Gravity: g/cm³ Solid Content (without thinner added): Weight % Volume % Important remarks: In countries/regions where higher temperatures above 25 C in combination with high relative humidity are experienced, we recommend to reduce the addition of Standox Demineralized Water to 0-5%. The equipment for water-thinnable products must be compatible with waterbased products. VOC (2004/42/EC): 2004/42/IIB(d)(420)420 The EU limit value for this product (product category: IIB.d) in ready for use form is max 420 g/litre of VOC. The VOC content of this product in ready for use form is max. 420 g/l. When collecting waste for disposal separate waterthinnable products from conventional ones, otherwise waste disposal will be more difficult and expensive, if not impossible. Spot repair see Standox Painting System S9. Theoretical Coverage: m²/l at 15 micron dry film thickness For professional use only! The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose. The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved. The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed. We may modify and/ or discontinue operation of all or portions of this Information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. SX-GB Version 13 Axalta Coating Systems Germany GmbH Christbusch Wuppertal 801 3/3 Germany

106 Standocryl VOC-Autolack VOC Topcoat High-quality VOC compliant Topcoat Economical application Excellent vertical stability Very short drying times Excellent polishability One visit application Technical Description: 3:1 VOC System Spot Repair / temperatures of C Standox Hardener VOC Drying min / C Partial respray / temperatures of C Standox Hardener VOC Drying min / C Partial respray / temperatures of C Standox Hardener VOC Drying min / C Total respray / temperatures of C Standox Hardener VOC Drying min / C An Axalta Coating Systems Brand SX-GB Version /3

107 Standocryl VOC-Autolack Substrate: Application: Standox Fillers Standox 1K Primer Filler Standoflex Primer Filler 3:1 with all Standox VOC Hardeners Potlife h / C Through-hardened sanded paintwork Isolate sensitive substrates with Standox Filler, preferably Standox VOC Nonstop Primer Filler U % Standox VOC Thinner s / DIN 4 mm / 20 C s / ISO 4 mm / 20 C Compliant mm bar inlet pressure = micron Pretreatment / Cleaning: For substrate preparation information see Standox Painting System S1. Use air fed respirator. Refer to relevant Health and Safety Data sheets. HVLP mm 0.7 bar atomization pressure = micron 5-10 min / C final flash-off Air dry overnight / C or min. / C panel temperature Short wave 5 min / 50% performance afterwards 10 min / 100% performance Alternatively 15% Standox 2K Thinner can be added. SX-GB Version /3

108 Standocryl VOC-Autolack Flash point: C / F Cleaning of equipment: Clean after use with Standox Cleaning Thinner. Specific Gravity: g/cm³ Solid Content (without thinner added): Weight % Volume % VOC (2004/42/EC): 2004/42/IIB(d)(420)420 The EU limit value for this product (product category: IIB.d) in ready for use form is max 420 g/litre of VOC. The VOC content of this product in ready for use form is max. 420 g/l. Important remarks: Standocryl VOC Topcoat can be used with: 15% Standox Plasticiser - mix 3:1 with Standox VOC Hardener and 15% Standox VOC Thinner, alternatively Standox 2K Thinner. For soft plastics 30% Standox Plasticiser have to be added. Standocryl VOC Topcoat can be overcoated within 24 h without intermediate sanding. Allow additional time for heating-up of combi spray booths. Theoretical Coverage: m²/l at 50 micron dry film thickness 2K Paints react with moisture. Therefore all equipment must be kept moisture free. Ready to use paint materials containing isocyanates can cause irritation of the mucous membranes - and of the respiratory organs, in particular - and cause hypersensitive reactions. There is a risk of hypersensitization if the vapour or spray mist is inhaled. When using materials containing isocyanates, all precautions relating to the handling of solvents should be carefully followed. In particular, care should be taken not to inhale spray mist or vapour. Asthma sufferers, those with allergies and anyone with a history of respiratory complaints must not be asked to work with products containing isocyanates. For professional use only! The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose. The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved. The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed. We may modify and/ or discontinue operation of all or portions of this Information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. SX-GB Version /3 Axalta Coating Systems Germany GmbH Christbusch Wuppertal Germany

109 Standohyd Basecoat Mercedes Alubeam 047 Special effect colour Specific application process Technical Description: Thin with 50 % Standohyd Special Effect Additive Painting system S9.13 describes the special blending-in process SX-GB Version /3

110 Standohyd Basecoat Mercedes Alubeam 047 Substrate: Sanded Standox EP Primer Surfacer 3:1 or Standox VOC System Filler Through-hardened sanded paintwork Do not forget cleaning! Pretreatment / Cleaning: For substrate preparation see Standox Painting System S1 Use air fed respirator. Refer to relevant Health and Safety Data Sheets. 1 normal coat 1 light coat with increased distance to object Flash off time can be reduced by - Using air blower - Spray booth blower system - Infrared drying - Increasing spray booth temperature to max. 45 C until mat Application: A Standocryl VOC Clear must be applied completely over any repaired panels, then cured and sanded Orbital sanding machine P1000-P1500 Edges and corners P3000 handsanding Add 50% Standohyd Special Effect Additive to the Mercedes 047 colour for standard application. Gently shake Standohyd Special Effect Additive before use. Compliant mm 2.0 bar inlet pressure 1.5 = micron HVLP mm 0.7 bar atomization pressure 1.5 = micron Final flash off until matt Standocryl VOC Platinum Clear SX-GB Version /3

111 Standohyd Basecoat Mercedes Alubeam 047 Flashpoint: 50 C / 122 F Specific Gravity: 1,004 g/cm 3 Solid Content (without thinner added): 11.6 Weight % 10.0 Volume % VOC (2004/42/EC): 2004/42/IIB(d)(420)420 The EU limit value for this product (product category: IIB.d) in ready for use form is max 420 g/litre of VOC. The VOC content of this product in ready for use form is max. 420 g/l. Cleaning of equipment: Rinse first with Standohyd Demineralized Water. Clean after use with Standox Cleaning Thinner. Important remarks: The equipment for water thinnable products must be compatible with waterbased products. When collecting waste for disposal, separate waterthinnable products from conventional ones, otherwise waste disposal will be more difficult and expensive, if not impossible. Large blend-in possible only. Painting system S9.13 describes the special blending-in process Best results with SATA NR3000 HVLP 1.3 mm spray gun Theoretical Coverage: 11 m 2 /l at 15 micron dry film thickness Standohyd Special Effect Additive should be added to the Standohyd Mercedes 047 colour directly before application, best results are when used within same working day. For professional use only! The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose. The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved. The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed. We may modify and/ or discontinue operation of all or portions of this Information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. SX-GB Standox GmbH Postfach Version 00 D Wuppertal 697 3/3 Germany

112 Standocryl VOC-HS-Klarlack K9520 VOC HS Clear K9520 High quality VOC Clear for panel repair and overall re-sprays High solid product Excellent vertical stability Material and time savings by reducing the number of spray passes One visit application Technical Description: Mix 2:1 with all Standox Hardeners HS Mix 3:1 with all Standox VOC Hardeners Force drying possible Air dry overnight / C An Axalta Coating Systems Brand SX-GB Version /4

113 Standocryl VOC-HS-Klarlack K9520 Substrate: Standohyd Basecoat Application: HS System Standoblue Basecoat Pretreatment / Cleaning: For substrate preparation see Standox Painting System S1 Use air fed respirator. Refer to relevant Health and Safety Data Sheets. 2:1 with all Standox HS Hardeners Potlife 1.5 h / C Ready to spray s / DIN 4mm / 20 C s / ISO 4 mm / 20 C Compliant mm bar inlet pressure = micron HVLP mm 0.7 bar atomization pressure = micron min / C final flash-off Air dry overnight / C or min. / C panel temperature Short wave 8-12 min (see Standox Painting System S10) SX-GB Version /4

114 Standocryl VOC-HS-Klarlack K9520 Substrate: Standohyd Basecoat Application: VOC System Standoblue Basecoat Pretreatment / Cleaning: For substrate preparation see Standox Painting System S1 Use air fed respirator. Refer to relevant Health and Safety Data Sheets. 3:1 with all Standox VOC Hardeners Potlife 1.5 h / C % Standox VOC Thinner s / DIN 4mm / 20 C s / ISO 4mm / 20 C Compliant mm bar inlet pressure = micron HVLP mm 0.7 bar atomization pressure = micron min / C final flash-off Air dry overnight / C or min. / C panel temperature Short wave 8-12 min (see Standox Painting System S10) SX-GB Version /4

115 Standocryl VOC-HS-Klarlack K9520 Flash point: 43 C / F Cleaning of equipment: Clean after use with Standox Cleaning Thinner. Specific Gravity: 1.01 g/cm³ Solid Content (without thinner added): 60.2 Weight % 54.4 Volume % VOC (2004/42/EC): 2004/42/IIB(d)(420)420 The EU limit value for this product (productcategory IIB.d) in ready to use form is max 420 g/l VOC. The VOC content of this product in ready for use form is max. 420 g/l. Important remarks: Standocryl VOC HS Clear K9520 can be overcoated within 24 h without intermediate sanding. Allow additional time for heating-up of combi spray booths. In countries without VOC legislation Standox Basecoat can be used as well. Theoretical Coverage: m²/l at 50 micron dry film thickness 2K Paints react with moisture. Therefore all equipment must be kept moisture free. Ready to use paint materials containing isocyanates can cause irritation of the mucous membranes - and of the respiratory organs, in particular - and cause hypersensitive reactions. There is a risk of hypersensitization if the vapour or spray mist is inhaled. When using materials containing isocyanates, all precautions relating to the handling of solvents should be carefully followed. In particular, care should be taken not to inhale spray mist or vapour. Asthma sufferers, those with allergies and anyone with a history of respiratory complaints must not be asked to work with products containing isocyanates. For professional use only. The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose. The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved. The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed. We may modify and/ or discontinue operation of all or portions of this Information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. SX-GB Version /4 Axalta Coating Systems Germany GmbH Christbusch Wuppertal Germany

116 Standocryl VOC-Platinum-Klarlack K9570 VOC Platinum Clear K9570 VOC clear for approval work Special VOC Clear with reflow effect for improved abrasion properties e.g. automatic car wash machines Durable high gloss for 2-stage finishes Extremely high mechanical and chemical resistance One visit application Technical Description: Mix 3:1 with Standox Hardener VOC or Standox Hardener VOC Force drying min / C panel temperature IR drying min An Axalta Coating Systems Brand SX-GB Version /3

117 Standocryl VOC-Platinum-Klarlack K9570 Substrate: Application: Standohyd Basecoat Standoblue Basecoat Pretreatment / Cleaning: For substrate preparation see Standox Painting System S1 Use air fed respirator. Refer to relevant Health and Safety Data Sheets. 3:1 with Standox Hardener VOC or Standox Hardener VOC Potlife min / C Ready to spray s / DIN 4mm / 20 C s / ISO 4mm / 20 C Compliant mm bar inlet pressure = micron HVLP mm 0.7 bar atomization pressure = micron 5-10 min / C final flash-off Air dry overnight / C or min. / C panel temperature Short wave min (see Standox Painting System S10) SX-GB Version /3

118 Standocryl VOC-Platinum-Klarlack K9570 Flashpoint: 38.0 C / F Cleaning of equipment: Clean after use with Standox Cleaning Thinner. Specific Gravity: 0.96 g/cm³ Solid Content (without thinner added): 49.6 Weight % 42.5 Volume % VOC (2004/42/EC): 2004/42/IIB(d)(420)420 The EU limit value for this product (productcategory IIB.d) in ready to use form is max 420 g/l VOC. The VOC content of this product in ready for use form is max. 420 g/l. Important remarks: Standocryl VOC Platinum Clear K9570 can be overcoated within 24 h without intermediate sanding. Allow additional time for heating-up of combi spray booths. Application only with Standox Hardener VOC or Standox Hardener VOC Do not use Standocryl VOC Platinum Clear K9570 with Standox Plasticiser or Standox Special Matt as properties will be negatively changed. Theoretical Coverage: 9-10 m²/l at 50 micron dry film thickness 2K Paints react with moisture. Therefore all equipment must be kept moisture free. Ready to use paint materials containing isocyanates can cause irritation of the mucous membranes - and of the respiratory organs, in particular - and cause hypersensitive reactions. There is a risk of hypersensitization if the vapour or spray mist is inhaled. When using materials containing isocyanates, all precautions relating to the handling of solvents should be carefully followed. In particular, care should be taken not to inhale spray mist or vapour. Asthma sufferers, those with allergies and anyone with a history of respiratory complaints must not be asked to work with products containing isocyanates. For professional use only! The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose. The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved. The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed. We may modify and/ or discontinue operation of all or portions of this Information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. SX-GB Version /3 Axalta Coating Systems Germany GmbH Christbusch Wuppertal Germany

119 Standocryl VOC-Premium-Klarlack K9540 VOC Premium Clear K9540 High quality VOC clear for partial and total respray One visit application Excellent vertical hold out Short drying times and very good throughdrying Very good polishability Very good flow and high gloss Technical Description: Mix 3:1 with all Standox VOC Hardeners Mix 2:1 with all Standox HS Hardeners Spot Repair / lower temperatures Standox Hardener HS 5-15 / VOC Drying min / C panel temperature Partial respray / temperatures of C Standox Hardener HS / VOC or Standox Hardener HS / VOC Drying min / C panel temperature Total respray / higher temperatures Standox Hardener HS / VOC Drying min / C panel temperature An Axalta Coating Systems Brand SX-GB Version /4

120 Standocryl VOC-Premium-Klarlack K9540 Substrate: Standohyd Basecoat Application: VOC System Standoblue Basecoat Pretreatment / Cleaning: For substrate preparation information see Standox Painting System S1. Use air fed respirator. Refer to relevant Health and Safety Data Sheets. 3:1 with all Standox VOC Hardeners Potlife min / C % Standox VOC Thinner s / DIN 4mm / 20 C s / ISO 4 mm / 20 C Compliant mm bar inlet pressure = micron HVLP mm 0.7 bar atomization pressure = micron 5-10 min / C final flash-off min / C panel temperature Short wave 8-12 min (see Standox Painting System S10) SX-GB Version /4

121 Standocryl VOC-Premium-Klarlack K9540 Substrate: Standohyd Basecoat Application: HS System Standoblue Basecoat 2:1 with all Standox HS Hardeners Potlife min / C Pretreatment / Cleaning: For substrate preparation information see Standox Painting System S1. Use air fed respirator. Refer to relevant Health and Safety Data Sheets. Ready to spray s / DIN 4mm / 20 C s / ISO 4 mm / 20 C Compliant mm bar inlet pressure = micron HVLP mm 0.7 bar atomization pressure = micron 5-10 min / C final flash-off min / C panel temperature Short wave 8-12 min (see Standox Painting System S10) SX-GB Version /4

122 Standocryl VOC-Premium-Klarlack K9540 Flash point: 44.0 C / F Cleaning of equipment: Clean after use with Standox Cleaning Thinner. Specific Gravity: 0.98 g/cm³ Solid Content (without thinner added): 56.9 Weight % 50.2 Volume % VOC (2004/42/EC): 2004/42/IIB(d)(420)420 The EU limit value for this product (productcategory IIB.d) in ready to use form is max 420g/ltr. VOC. The VOC content of this product in ready for use form is max. 420 g/l. Important remarks: Standocryl VOC Premium Clear K9540 can be overcoated within 24 h without intermediate sanding. Allow additional time for heating-up of combi spray booths. Standocryl VOC Premium Clear K9540 can be used with: - Standox Special Matt - Standox Plasticiser Air dry overnight C possible. In countries without VOC legislation Standox Basecoat can be used as well. Theoretical Coverage: 9-10 m²/l at 50 micron dry film thickness 2K Paints react with moisture. Therefore all equipment must be kept moisture free. Ready to use paint materials containing isocyanates can cause irritation of the mucous membranes - and of the respiratory organs, in particular - and cause hypersensitive reactions. There is a risk of hypersensitization if the vapour or spray mist is inhaled. When using materials containing isocyanates, all precautions relating to the handling of solvents should be carefully followed. In particular, care should be taken not to inhale spray mist or vapour. Asthma sufferers, those with allergies and anyone with a history of respiratory complaints must not be asked to work with products containing isocyanates. For professional use only! The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose. The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved. The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed. We may modify and/ or discontinue operation of all or portions of this Information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. SX-GB Version 09 Axalta Coating Systems Germany GmbH Christbusch Wuppertal 582 4/4 Germany

123 Standocryl VOC-Express-Klarlack K9530 VOC Express Clear K9530 High quality VOC clear for partial and total respray Very fast drying Good polishability Flexible in application and drying conditions One visit application Technical Description: 3:1 VOC System Force drying min / C panel temperature An Axalta Coating Systems Brand SX-GB Version /3

124 Standocryl VOC-Express-Klarlack K9530 Substrate: Application: Standohyd Basecoat Standoblue Basecoat Pretreatment / Cleaning: For substrate preparation see Standox Painting System S1 3:1 with Standox VOC Hardener potlife min/18-22 C 10% Standox VOC Thinners s / DIN 4 mm / 20 C s / ISO 4 mm / 20 C Compliant mm bar inlet pressure = micron Use air fed respirator. Refer to relevant Health and Safety Data Sheets. HVLP mm 0.7 bar atomization pressure = micron 5-10 min / C final flash-off Suggestions for use: Spot Repair / Panel Repair Standox Hardener VOC and VOC Thinner Special / Express Partial respray Standox Hardener VOC / Hardener VOC and Thinner VOC / Thinner VOC Total respray Standox Hardener VOC and Thinner VOC Air dry overnight / C or min. / C panel temperature depending on hardener and thinner used Short wave10-15 min (see Standox Painting System S10) SX-GB Version /3

125 Standocryl VOC-Express-Klarlack K9530 Flash point: 43.0 C / F Cleaning of equipment: Clean after use with Standox Cleaning Thinner. Specific Gravity: 0.98 g/cm³ Solid Content (without thinner added): 54.0 Weight % 47.1 Volume % VOC (2004/42/EC): 2004/42/IIB(d)(420)420 The EU limit value for this product (productcategory IIB.d) in ready to use form is max 420 g/l VOC. The VOC content of this product in ready for use form is max. 420 g/l. Important remarks: Standocryl VOC Express Clear K9530 can be overcoated within 24 h without intermediate sanding. Allow additional time for preheating up to panel temperature. Application only with Standox VOC Hardeners and VOC Thinners. For best results material temperature should be above 20 C. Theoretical Coverage: approx. 10 m²/l at 50 micron dry film thickness 2K Paints react with moisture. Therefore all equipment must be kept moisture free. Ready to use paint materials containing isocyanates can cause irritation of the mucous membranes - and of the respiratory organs, in particular - and cause hypersensitive reactions. There is a risk of hypersensitization if the vapour or spray mist is inhaled. When using materials containing isocyanates, all precautions relating to the handling of solvents should be carefully followed. In particular, care should be taken not to inhale spray mist or vapour. Asthma sufferers, those with allergies and anyone with a history of respiratory complaints must not be asked to work with products containing isocyanates. For professional use only! The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose. The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved. The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed. We may modify and/ or discontinue operation of all or portions of this Information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. SX-GB Version /3 Axalta Coating Systems Germany GmbH Christbusch Wuppertal Germany

126 Standocryl VOC-Xtra-Klarlack K9560 VOC Xtra Clear K9560 High quality VOC clear for partial and total respray One visit or 2 coat application Good gloss and flow Technical Description: 3:1 VOC System Force drying min / C panel temperature An Axalta Coating Systems Brand SX-GB Version /3

127 Standocryl VOC-Xtra-Klarlack K9560 Substrate: Application: Standoblue Basecoat Standohyd Basecoat Pretreatment / Cleaning: For substrate preparation information see Standox Painting System S1. Use air fed respirator. Refer to relevant Health and Safety Data Sheets. 3:1 with Standox VOC Hardener potlife min/18-22 C 5% Standocryl VOC 2K Additive s / DIN 4 mm / 20 C s / ISO 4 mm / 20 C Compliant mm bar inlet pressure = micron HVLP mm 0.7 bar atomization pressure = micron Optional: Application in two coats with 5-10 min flash-off between coats For 2 coat application: 1 st spray pass: thin and closed Allow for 5-10 min flash-off time Apply a 2 nd spray pass as normal Allow for 5-10 min final flash-off time 5-10 min / C flash off between coats and final flash off Air dry overnight / C or min. / C panel temperature Short wave min (see Standox Painting System S10) SX-GB Version /3

128 Standocryl VOC-Xtra-Klarlack K9560 Flash point: 35 C / 95 F Cleaning of equipment: Clean after use with Standox Cleaning Thinner. Specific Gravity: 0.98 g/cm³ Solid Content (without thinner added): 53.3 Weight % 47.0 Volume % VOC (2004/42/EC): 2004/42/IIB(d)(420)420 The EU limit value for this product (product category: IIB.d) in ready for use form is max 420 g/litre of VOC. The VOC content of this product in ready for use form is max. 420 g/l. Important remarks: Standocryl VOC Xtra Clear K9560 can be overcoated within 24 h without intermediate sanding. Allow additional time for preheating up to panel temperature. Application only with all Standox VOC Hardeners. For best results material temperature should be above 20 C. Standocryl VOC 2K Additive can be replaced by Standox Thinner VOC Special / VOC Express for micro repair only. Theoretical Coverage: approx. 10 m²/l at 50 micron dry film thickness 2K Paints react with moisture. Therefore all equipment must be kept moisture free. Ready to use paint materials containing isocyanates can cause irritation of the mucous membranes - and of the respiratory organs, in particular - and cause hypersensitive reactions. There is a risk of hypersensitization if the vapour or spray mist is inhaled. When using materials containing isocyanates, all precautions relating to the handling of solvents should be carefully followed. In particular, care should be taken not to inhale spray mist or vapour. Asthma sufferers, those with allergies and anyone with a history of respiratory complaints must not be asked to work with products containing isocyanates. For professional use only! The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose. The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved. The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed. We may modify and/ or discontinue operation of all or portions of this Information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. SX-GB Version 02 Axalta Coating Systems Germany GmbH Christbusch Wuppertal /3 Germany

129 Standox Elastik-Additiv Plasticiser Universal plasticiser for all MS and VOC topcoat systems Suitable for Standox Filler For plastic finishes High long-term elasticity Technical Description: For all car plastic panels Add 15% of plasticiser to topcoats, clearcoats and fillers with medium and hard plastics Unless listed in the following table standard mixing ratios apply when using Standox Plasticiser. An Axalta Coating Systems Brand SX-GB Version /3

130 Standox Elastik-Additiv Standox VOC Filler Mixing Ratio without Standox Plasticiser Mixing Ratio with 15% Standox Plasticiser Standox VOC Xtra Filler U7560 Standox VOC System Filler U7540 5:1 Standox VOC Hardener 3:1 Standox MS Hardener 4:1 Standox VOC Hardener + 10% Standox VOC Thinner 2:1 Standox MS Hardener 4:1 Standox HS Hardener 3:1 Standox HS Hardener 7:1 Standox VOC Hardener 4:1 Standox VOC Hardener Standox VOC Pro Filler U7530 4:1 Standox MS Hardener 2:1 Standox MS Hardener 5:1 Standox HS Hardener 3:1 Standox HS Hardener 7:1 Standox VOC Hardener 4:1 Standox VOC Hardener Standox VOC Nonstop Primer Filler U7550 3:1 Standox HS Hardener 5:1 Standox VOC Hardener 2:1 Standox HS Hardener 4:1 Standox VOC Hardener Standox Easy Filler U7010 4:1 Standox MS Easy Hardener 4:1 Standox MS Hardener 2:1 Standox MS Easy Hardener 2:1 Standox MS Hardener Standox Transparent Adhesion Sealer U7020 6:1 Standox VOC Easy Hardener 3:1 Standox HS Hardener 4:1 Standox VOC Hardener 4:1 Standox VOC Easy Hardener 2:1 Standox HS Hardener 3:1 Standox VOC Hardener SX-GB Version /3

131 Standox Elastik-Additiv Flashpoint: 24 C / 75.2 F Cleaning of equipment: Clean after use with Standox Cleaning Thinner. Specific Gravity: 1.1 g/cm³ Important remarks: Solid Content (without thinner added): 79.8 Weight % 74.8 Volume % Standox Plasticiser must be included before the addition of Hardener. Only mix Standox Plasticiser with Standox VOC Nonstop Primer Filler U7550 directly before use. To optimise the sanding properties the elastified fillers should be dried 45 min / C panel temperature 2K Paints react with moisture. Therefore all equipment must be kept moisture free. Ready to use paint materials containing isocyanates can cause irritation of the mucous membranes - and of the respiratory organs, in particular - and cause hypersensitive reactions. There is a risk of hypersensitization if the vapour or spray mist is inhaled. When using materials containing isocyanates, all precautions relating to the handling of solvents should be carefully followed. In particular, care should be taken not to inhale spray mist or vapour. Asthma sufferers, those with allergies and anyone with a history of respiratory complaints must not be asked to work with products containing isocyanates. For professional use only! The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose. The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved. The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed. We may modify and/ or discontinue operation of all or portions of this Information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. SX-GB Version 15 Axalta Coating Systems Germany GmbH Christbusch Wuppertal 590 3/3 Germany

132 Standoflex Plastic-Primer Plastic Primer 1K Primer for 3-stage plastic painting system Easy to apply Adheres to all exterior plastic car parts Ready to spray Technical Description: 1 spray pass Standoflex Plastic Primer Flash off 10 min / C Overcoat wet-on-wet with plasticised Standox Filler SX-GB Version /3

133 Standoflex Plastic-Primer Substrate: Application: Exterior plastic car parts Ready to spray Shake well before use Pretreatment / Cleaning: For substrate preparation information see Standox Painting System S1. Use air fed respirator. Refer to relevant Health and Safety Data sheets. Compliant mm bar inlet pressure 1 = 1-2 micron HVLP mm 0.7 bar atomization pressure 1 = 1-2 micron Air dry 10 min / C Plasticised Standox Filler SX-GB Version /3

134 Standoflex Plastic-Primer Flashpoint: 23 C / 73.4 F Cleaning of equipment: Clean after use with Standox Cleaning Thinner. Specific Gravity: 0.88 g/cm 3 Solid Content (without thinner added): 4.8 Weight % 3.8 Volume % Important remarks: Apply a thin coat of Standoflex Plastic-Primer See Standox Plastic Painting Systems (S ) Theoretical Coverage: 17 m 2 /l at 2 micron dry film thickness For professional use only! The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose. The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved. The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed. We may modify and/ or discontinue operation of all or portions of this Information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. SX-GB Version /3 Standox GmbH Postfach D Wuppertal Germany

135 Standoflex Porenfüller U3080 Pore Filler U3080 1K Pore Filler for micropores in plastic surfaces Technical Description: Apply by wiping An Axalta Coating Systems Brand SX-GB Version /3

136 Standoflex Porenfüller U3080 Substrate: Application: Porous plastic parts, especially for PUR soft plastics Apply Standoflex Pore Filler U3080 with a lint free cloth using a circular action. Pretreatment / Cleaning: For substrate preparation information see Standox Painting System S1. To remove excess material use a cloth moistened with Standoflex Plastic Cleaner antistatic Standoflex Plastic Primer U3060 Use air fed respirator. Refer to relevant Health and Safety Data sheets. Standoflex 2K Plastic Primer Surfacer U3200 SX-GB Version /3

137 Standoflex Porenfüller U3080 Flashpoint: Important remarks: 25 C / 77 F Use for filling micropores only. Specific Gravity: 1.60 g/cm³ Solid Content (without thinner added): 71.5 Weight % 39.5 Volume % For professional use only! The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose. The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved. The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed. We may modify and/ or discontinue operation of all or portions of this Information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. SX-GB Version 06 Axalta Coating Systems Germany GmbH Christbusch Wuppertal 740 3/3 Germany

138 Standoflex 2K-Plastik-Grundierfüller U3200 2K Plastic Primer Surfacer U3200 2K Primer Surfacer for plastics Easy application Adheres to all exterior plastic car parts Wet-on-Wet working process or can be used as a sanding filler Easy handling One visit application Technical Description: Mixing ratio 1:1 with Standoflex 2K Plastic Hardener U3210 Ready to spray after addition of hardener Potlife 8-10 h / C An Axalta Coating Systems Brand SX-GB Version /3

139 Standoflex 2K-Plastik-Grundierfüller U3200 Substrate: Application: Exterior plastic car parts 1:1 with Standoflex 2K Plastic Hardener U3210 Potlife 8-10 h / C Pretreatment / Cleaning: For substrate preparation see Standox Painting System S1 Use air fed respirator. Refer to relevant Health and Safety Data Sheets. Ready to spray after addition of Hardener s / DIN 4mm / 20 C s / ISO 4mm / 20 C Compliant mm bar inlet pressure = 25 micron HVLP mm 0.7 bar atomization pressure = 25 micron Wet-on-Wet Application final flash-off min. 30 min / C For filling small scratches and imperfections, after pre-priming with Standoflex 2K Plastic Primer Surfacer U3200 and drying according to instructions, apply Standox Fine Stopper U1070. After denibbing the body filler spot should be isolated with Standoflex 2K Plastic Primer Surfacer U min / C or 2 h / C If necessary denib with P400 Plasticised Standocryl VOC Topcoat or Standohyd / Standoblue Basecoat with plasticised Standocryl VOC Clears SX-GB Version /3

140 Standoflex 2K-Plastik-Grundierfüller U3200 Flash point: 23 C / 73.4 F Cleaning of equipment: Clean immediately after use with Standox Cleaning Thinner. Specific Gravity: 1,20-1,22 g/cm³ Solid Content (without thinner added): Weight % Volume % Important remarks: Only use Standoflex 2K Plastic Hardener U3210 Do not store Standoflex 2K Plastic Hardener U3210 below +10 C. See Standox Plastic Painting Systems (S ) Theoretical Coverage: 7.8 m²/l at 30 micron dry film thickness Standoflex 2K Plastic Primer Surfacer U3200 is available in bright grey and black for bright and dark Standox topcoat colours. Must be overcoated within 24 hours in wet-on-wet process In countries without VOC legislation Standocryl 2K Topcoat / Standocryl 2K Topcoat NEW and Standox Basecoat can be used as well. For professional use only! The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose. The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved. The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed. We may modify and/ or discontinue operation of all or portions of this Information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. SX-GB Version /3 Axalta Coating Systems Germany GmbH Christbusch Wuppertal Germany

141 Standocryl 2K-KS-Klarlack seidenglänzend 2K Plastic Clear Satin Gloss Special silk gloss, elastic 2K clear for plastics High mechanical and chemical resistance Technical Description: Mix 5:1 with all Standox VOC Hardeners Mix 3:1 with all Standox 2K HS Hardeners Mix 2:1 with all Standox 2K MS Hardener Force drying possible Air dry overnight / C SX-GB Version /5

142 Standocryl 2K-KS-Klarlack seidenglänzend Substrate: Standohyd Basecoat Pretreatment / Cleaning: Gloss level 49 units at 60 angle For substrate preparation information see Standox Painting System S1. Use air fed respirator. Refer to relevant Health and Safety Data sheets. Application: VOC System 5:1 with all Standox VOC Hardeners Potlife 5-6 h / C 20% Standox 2K Thinner s / DIN 4 mm / 20 C s / ISO 4 mm / 20 C Compliant mm bar inlet pressure 2 = micron HVLP mm 0.7 bar atomization pressure 2 = micron 5-10 min / C Flash off between coats and final flash off min / C or min / 80 C panel temperature SX-GB Version /5

143 Standocryl 2K-KS-Klarlack seidenglänzend Substrate: Standohyd Basecoat Pretreatment / Cleaning: Gloss level 46 units at 60 angle For substrate preparation information see Standox Painting System S1. Use air fed respirator. Refer to relevant Health and Safety Data sheets. Application: HS System 3:1 with all Standox 2K HS Hardeners Potlife 5-6 h / C 10% Standox 2K Thinner s / DIN 4 mm / 20 C s / ISO 4 mm / 20 C Compliant mm bar inlet pressure 2 = micron HVLP mm 0.7 bar atomization pressure 2 = micron 5-10 min / C Flash off between coats and final flash off min / C or min / 80 C panel temperature SX-GB Version /5

144 Standocryl 2K-KS-Klarlack seidenglänzend Substrate: Standohyd Basecoat Pretreatment / Cleaning: Gloss level 48 units at 60 angle For substrate preparation information see Standox Painting System S1. Use air fed respirator. Refer to relevant Health and Safety Data sheets. Application: MS System 2:1 with all Standox 2K MS Hardeners Potlife 5-6 h / C 0-5 % Standox 2K Thinner s / DIN 4 mm / 20 C s / ISO 4 mm / 20 C Compliant mm bar inlet pressure 2 = micron HVLP mm 0.7 bar atomization pressure 2 = micron 5-10 min / C Flash off between coats and final flash off min / C or min / 80 C panel temperature SX-GB Version /5

145 Standocryl 2K-KS-Klarlack seidenglänzend Flashpoint: 24 C / 75.2 F Cleaning of equipment: Clean after use with Standox Cleaning Thinner. Specific Gravity: (without thinner added): 51.3 Weight % 42.7 Volume % 1.04 g/cm 3 Allow additional time for heating-up of combi spray Solid Content VOC (2004/42/EC): 2004/42/IIB(e)(840)580 The EU limit value for this product (productcategory IIB.e) in ready to use form is max 840g/ltr. The VOC content of this product in ready for use form is max. 580 g/l. Important remarks: booths. In countries without VOC legislation Standox Basecoat can be used as well. Theoretical Coverage: 7.8 m 2 /l at 50 micron dry film thickness 2K Paints react with moisture. Therefore all equipment must be kept moisture free. Ready to use paint materials containing isocyanates can cause irritation of the mucous membranes - and of the respiratory organs, in particular - and cause hypersensitive reactions. There is a risk of hypersensitization if the vapour or spray mist is inhaled. When using materials containing isocyanates, all precautions relating to the handling of solvents should be carefully followed. In particular, care should be taken not to inhale spray mist or vapour. Asthma sufferers, those with allergies and anyone with a history of respiratory complaints must not be asked to work with products containing isocyanates. For professional use only! The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose. The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved. The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed. We may modify and/ or discontinue operation of all or portions of this Information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. SX-GB Standox GmbH Postfach Version 04 D Wuppertal 569 5/5 Germany

146 Standox Reiniger Precleaner Waterborne cleaning agent Mild odour Reduced solvent emissions Technical Description: For preliminary cleaning of sanded finishes and primed surfaces An Axalta Coating Systems Brand SX-GB Version /3

147 Standox Reiniger Substrate: Through-hardened sanded paintwork Application: Waterborne cleaning agent Standox Filler, sanded Apply by means of a soaked cloth or spray can and remove with a clean, dry cloth. Pretreatment / Cleaning: Use air jet to blast residual moisture from corners and crevices. Ventilate surfaces well before further treatment. For substrate preparation information see Standox Painting System S1. Use air fed respirator. Refer to relevant Health and Safety Data sheets. SX-GB Version /3

148 Standox Reiniger Flashpoint: Important remarks: 29 C / 84.2 F Do not allow Standox Precleaner to dry on surfaces. Specific Gravity: 0.95 g/cm³ VOC (2004/42/EC): 2004/42/IIB(a)(200)200 The EU limit value for this product (productcategory IIB.a) in ready to use form is max 200g/ltr. The VOC content of this product in ready for use form is max. 200 g/l. Change cloths often. When collecting waste for disposal separate waterthinnable products from conventional ones, otherwise waste disposal will be more difficult and expensive, if not impossible. For professional use only! The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose. The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved. The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed. We may modify and/ or discontinue operation of all or portions of this Information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. SX-GB Version 02 Axalta Coating Systems Germany GmbH Christbusch Wuppertal 803 3/3 Germany

149 Standox Entfettungsmittel TB 50 Degreaser TB 50 Waterborne degreaser Mild odour Reduced solvent emissions Technical Description: For cleaning of metal substrates An Axalta Coating Systems Brand SX-GB Version /3

150 Standox Entfettungsmittel TB 50 Substrate: Metal substrates Application: Degreaser Apply by means of a soaked cloth and remove with a clean, dry cloth. Pretreatment / Cleaning: For substrate preparation information see Standox Painting System S1. For better surface cleaning use ultra fine pad and dry with a lintfree cloth. Use air fed respirator. Refer to relevant Health and Safety Data sheets. SX-GB Version /3

151 Standox Entfettungsmittel TB 50 Flashpoint: 24 C / 75.2 F Important remarks: Do not allow Standox Degreaser TB 50 to dry on surfaces. Specific Gravity: 0.89 g/cm³ Solid Content (without thinner added): 0.1 Weight % Change cloths often. When collecting waste for disposal separate waterthinnable products from conventional ones, otherwise waste disposal will be more difficult and expensive, if not impossible. Not suitable for cleaning of sandblasted substrates. VOC (2004/42/EC): 2004/42/IIB(a)(850)430 The EU limit value for this product (productcategory IIB.a) in ready to use form is max 850g/ltr. The VOC content of this product in ready for use form is max. 430 g/l. For professional use only! The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose. The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved. The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed. We may modify and/ or discontinue operation of all or portions of this Information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. SX-GB Version 05 Axalta Coating Systems Germany GmbH Christbusch Wuppertal 808 3/3 Germany

152 Standohyd Steinschlagschutz Stone Chip Primer Water-thinnable Highly flexible Surface, textured or smooth Chromate-free Overcoatable Technical Description: Spray unthinned or with 10-20% Standohyd Demineralized Water Film thickness up to 300 micron Air dry overnight / C SX-GB I-2006/Version /4

153 Standohyd Steinschlagschutz Substrate: Through-hardened sanded paintwork Surfaces, covered with primer and filler, sanded Standox EP Primer Surfacer, sanded Polystyrene Pretreatment / Cleaning: Application: Textured surface 3-4 mm 3-4 bar 1-3 = micron Air dry overnight / C Standocryl VOC Topcoat or Standohyd Basecoat with Standocryl VOC Clears For substrate preparation information see Standox Painting System S1. Use air fed respirator. Refer to relevant Health and Safety Data sheets. For rel. humidity of 30-70% and ambient temperature C The flash off time will depend on the temperature, humidity and air flow in the spraybooth. SX-GB I-2006/Version /4

154 Standohyd Steinschlagschutz Substrate: Through-hardened sanded paintwork Surfaces, covered with primer and filler, sanded Standox EP Primer Surfacer, sanded Polystyrene Pretreatment / Cleaning: Application: Smooth surface 10-20% Standohyd VE-Wasser Compliant mm bar inlet pressure 2-3 = micron HVLP mm 0.7 bar atomization pressure 2-3 = micron Air dry overnight / C For substrate preparation information see Standox Painting System S1. If necessary denib wet with P800 and clean with a tack rag. Use air fed respirator. Refer to relevant Health and Safety Data sheets. Standocryl VOC Topcoat or Standohyd Basecoat with Standocryl VOC Clears For rel. humidity of 30-70% and ambient temperature C The flash off time will depend on the temperature, humidity and air flow in the spraybooth. SX-GB I-2006/Version /4

155 Standohyd Steinschlagschutz Flashpoint: Weight % Volume % 101 C / F Specific Gravity: g/cm 3 Solid Content (without thinner added): VOC (2004/42/EC): 2004/42/IIB(c)(540)130 The EU limit value for this product (product category: IIB.c) in ready for use form is max 540 g/l of VOC. The VOC content of this product in ready for use form is max. 130 g/l. Theoretical Coverage: 5.2 m 2 /l at 125 micron dry film thickness Cleaning of equipment: Rinse first with Standohyd Demineralized Water. Clean after use with Standox Cleaning Thinner. Important remarks: Do not apply to old underseal. Do not use on acid primers. Before further treatment with Standohyd Basecoat the water-thinnable Basecoat must be allowed to flash off. When collecting waste for disposal separate waterthinnable products from conventional ones, otherwise waste disposal will be more difficult and expensive, if not impossible. Do not put cleaning water into drains. In countries without VOC legislation Standox Basecoat / Standocryl 2K Topcoat can be used as well. For professional use only! The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose. The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved. The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed. We may modify and/ or discontinue operation of all or portions of this Information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. SX-GB Standox GmbH Postfach I-2006/Version 05 D Wuppertal 810 4/4 Germany

156 Standox Smart Blend Plus Thinner for blend-in with Standocryl VOC Clears and Standocryl VOC Topcoat Technical Description: Apply pure on blending area Force drying possible Air dry overnight / C An Axalta Coating Systems Brand SX-GB Version /4

157 Standox Smart Blend Plus Substrate: For preparation of repair areas see Standox Painting System S3. Keep surface for priming with filler as small as possible. Application: Blending-in with Standocryl VOC Topcoat Spray repair area with Standocryl VOC Topcoat until covered Pretreatment / Cleaning: For substrate preparation information see Standox Painting System S1. Apply Standox Smart Blend Plus on blending area Blend-in the overlapping area with reduced pressure (by bar) Use air fed respirator. Refer to relevant Health and Safety Data sheets. Polish after air dry overnight / C or 30 min / C panel temperature Polish after 1 h Short wave 8-12 min Polish after 1 h SX-GB Version /4

158 Standox Smart Blend Plus Substrate: For preparation of repair areas see Standox Painting System S3. Keep surface for priming with filler as small as possible. Application: Blending-in with Standocryl VOC Clears Spray repair area with Standocryl VOC Clears Pretreatment / Cleaning: For substrate preparation information see Standox Painting System S1. Apply Standox Smart Blend Plus on blending area Blend-in the overlapping area with reduced pressure (by bar) Use air fed respirator. Refer to relevant Health and Safety Data sheets. Polish after air dry overnight / C or 30 min / C panel temperature Polish after 1 h Short wave 8-12 min Polish after 1 h SX-GB Version /4

159 Standox Smart Blend Plus Flashpoint: 20 C / 68 F Cleaning of equipment: Clean after use with Standox Cleaning Thinner. Specific Gravity: 0.93 g/cm³ 2K Paints react with moisture. Therefore all equipment must be kept moisture free. Ready to use paint materials containing isocyanates can cause irritation of the mucous membranes - and of the respiratory organs, in particular - and cause hypersensitive reactions. There is a risk of hypersensitization if the vapour or spray mist is inhaled. When using materials containing isocyanates, all precautions relating to the handling of solvents should be carefully followed. In particular, care should be taken not to inhale spray mist or vapour. Asthma sufferers, those with allergies and anyone with a history of respiratory complaints must not be asked to work with products containing isocyanates. For professional use only! The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose. The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved. The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed. We may modify and/ or discontinue operation of all or portions of this Information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. SX-GB Version 02 Axalta Coating Systems Germany GmbH Christbusch Wuppertal 944 4/4 Germany

160 Standox Smart Blend Plus Thinner for blend-in of Standocryl VOC Clears and Standocryl VOC Topcoat Spray can Technical Description: Force drying possible Air dry overnight / C An Axalta Coating Systems Brand SX-GB Version /4

161 Standox Smart Blend Plus Substrate: For preparation of repair areas see Standox Painting System S3. Keep surface for priming with filler as small as possible. Application: Blending-in of Standocryl VOC Topcoat Spray repair area with Standocryl VOC Topcoat until covered Pretreatment / Cleaning: Apply several thin coats of Standox Smart Blend Plus on blending area For substrate preparation information see Standox Painting System S1. Use air fed respirator. Refer to relevant Health and Safety Data sheets. Polish after air dry overnight / C or 30 min / C panel temperature Polish after 1 h Short wave 8-12 min Polish after 1 h SX-GB Version /4

162 Standox Smart Blend Plus Substrate: For preparation of repair areas see Standox Painting System S3. Keep surface for priming with filler as small as possible. Application: Blending-in of Standocryl VOC Clears Spray repair area with Standocryl VOC Clears Pretreatment / Cleaning: Apply several thin coats of Standox Smart Blend Plus on blending area For substrate preparation information see Standox Painting System S1. Use air fed respirator. Refer to relevant Health and Safety Data sheets. Polish after air dry overnight / C or 30 min / C panel temperature Polish after 1 h Short wave 8-12 min Polish after 1 h SX-GB Version /4

163 Standox Smart Blend Plus Flashpoint: -1 C / 30.2 F Specific Gravity: g/cm³ Solid Content (without thinner added): 2.1 Weight % 1.4 Volume % VOC (2004/42/EC): 2004/42/IIB(e)(840)770 The EU limit value for this product (productcategory IIB.e) in ready to use form is max 840g/ltr. The VOC content of this product in ready for use form is max. 770 g/l. For professional use only! The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose. The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved. The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed. We may modify and/ or discontinue operation of all or portions of this Information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments. SX-GB Version 03 Axalta Coating Systems Germany GmbH Christbusch Wuppertal /4 Germany

164 Standohyd Color Blend For blending-in Standohyd Basecoat Easy handling Ready to spray Technical Description: Ready to spray or Mix 1:1 with Standohyd Basecoat An Axalta Coating Systems Brand SX-GB Version /4

165 Standohyd Color Blend Substrate: For preparation of repair areas see Standox Painting Systems S 9.5 / 9.6 and for alternative use of Standohyd Color Blend see Standox Painting Systems S 9.7 / 9.8. Keep surface for priming with filler as small as possible. Application: Blending-in Standohyd Basecoat directly with Standohyd Color Blend Spray blending area with one coat of Standohyd Color Blend. Pretreatment / Cleaning: Apply mixed Standohyd Basecoat in the wet film until covered. For substrate preparation information see Standox Painting System S1. Blend-in the overlapping area with reduced air pressure ( bar). Use air fed respirator. Refer to relevant Health and Safety Data sheets. Standocryl VOC Clears SX-GB Version /4

166 Standohyd Color Blend Substrate: For preparation of repair areas see Standox Painting Systems S 9.5 / 9.6 and for alternative use of Standohyd Color Blend see Standox Painting Systems S 9.7 / 9.8. Keep surface for priming with filler as small as possible. Application: Blending-in with Standohyd Basecoat mixed with Standohyd Color Blend Mix Standohyd Basecoat 1:1 with Standohyd Color Blend Pretreatment / Cleaning: Blend-in the overlapping area with reduced air pressure (by bar) For substrate preparation information see Standox Painting System S1. Use air fed respirator. Refer to relevant Health and Safety Data sheets. Standocryl VOC Clears Note: Occasionally it may be necessary to obtain opacity on the fillered area before proceeding. SX-GB Version /4