MicroPulse 302MFK. English

Transcription

1 MicroPulse 302MFK English

2 The Power Source MicroPulse 302MFK Multi Process Portable MIG MAG Synergic MIG MAG Pulse / Double Pulse NEW POWER SOURCE INVERTER MIG MAG SYNERGIC W.ECO Technology Inside POWER FACTOR CORRECTOR: Lower harmonic current emissions Lower input current Friendly Harmonic New technological solutions in order to reduce the harmonic current emissions according to the future International Standards Maximum safety HAC Hybrid Arc Control Soft Arc, low spattering Better welds, money savings Phase Detector Maximum protection MIG MAG PULSE/ DOUBLE PULSE MMA The natural increase of productivity Electrodes up to 8mm diameter can be easily welded thanks to its 250A- 40% duty factor at 40 C in MMA mode. The solution that allows a higher productivity WIG DC LIFT Lift TIG DC Ignition reduces Tungsten inclusions

3 MicroPulse 302MFK Multi Applications Maintenance Assembling Car Repairing Precision Welding Innovative System to clean the machine without opening the external structure body Ventilation grids and ventilators removable to allow an easy cleaning of the heat sink, by means of compressed air.

4 MicroPulse 302MFK HAC (Hybrid Arc Control) SPRAY ARC: HAC allows you to have a short spray arc with better penetration of the root, lower heat input and higher welding speed with no edge cutting and spattering. WELDING POSITION: HAC gives an optimal fusion of the bead s edges in short arc welding and to make overhead and vertical up position welding easier. PG POSITION: HAC allows thin plates welding in vertical down position with gap up to 5mm wide. THIN PLATES: HAC gives smooth and controlled short arc at lower parameters too. Low spattering, good edge wetting, low heating and small deformation are achieved in thin plate welding. BURN BACK: An optimal wire cutting at the end of welding helps perfect starts. SOFT START: Approaching speed of wire and welding dynamics are totally synergic giving low spattering at start, in any type of material. SPOT WELDING: Dedicated controls, low spattering and high executionspeed allow you to get perfect welding spots. 3T SPECIAL: allows you to set and recall 3 different current levels by pushing the trigger switch in order to achieve top quality weld beads: Highly recommended for Aluminum welding LEVEL 3: A low current ends the welding optimally by filling the crater on weld beads. LEVEL 2: The welding current is optimized with the plate thickness and the requested weld. LEVEL 1: A correct initial current gives optimal penetration from welding start.

5 The natural increase of productivity Pulse HS stands for: 1 - Higher execution speed High dynamics applied to the pulsation of HS Pulse arc gives an extremely and focused arc that increases the fluidity and pression of transfer as well as the wettability of joints. This allows the operator (or automatism) to proceed faster with the torch and a time saving of 35%. 2 - Higher deposition rate High dynamics applied to the pulse of Pulse HS arc allows to increase wire s speed while keeping same current value when welding in Standard Pulse. The increase of wire quantity in the pool increases consequently the weight of deposit in the unit of time (Kg/h). 3 - Lower heat input and less plastic deformation In Pulse HS heat input is lower (35%) than Standard Pulse. 4 - Better mechanical properties From our tests we obtain that tensile strengths values in the Pure Deposit and Heat Affected Zone (HAZ) are much higher in Standard Pulse. This means that a higher heat input increased considerably tensile strengths. In HS Pulse, hardness and tensile strengths are in line with the class of metal the base material belongs to, therefore the heat input is non influential in the welded material. Standard Pulse Fillet welding10,0mm HS Pulse Fillet welding10,0mm HAZ1 HAZ2 5 - Higher penetration, lower risk of lack of fusion Penetration obtained in HS Pulse (P2is considerably higher compare to Standard Pulse (P1). Moreover weld face is smoother thanks to the excellent joints wettabiltiy. Standard Pulse Fillet welding10,0mm HS Pulse Fillet welding10,0mm P1 P2 6 - Lower production costs and depreciation The higher execution speed combined with the higher deposition rate reduce remarkably both times and working costs. Less defects on the material and almost no need of reworking allow a always better amortization.

6 The solution that allows a higher productivity The difference between Standard Mig Mag welding and Power Focus The difference between Standard Mig Mag welding and Power Focus is to be found on the concentration and precision of the arc. The concentration on the Power Focus mode allows to focalize the high arc temperature precisely on the middle of the deposition, avoiding overheating on theweld edges. The heat affected zone (HAZ) is by Power Focus mode less expanded Standard Specifications of Standard Arc The main property of the Standard Arc is to be found on its high stability both during the Short Arc and the Spray Arc phase. In most of the commercialized welding machines, a transition phase called Globular phase is present. This welding area is normally characterized by unstable arcs, very difficult to be handled, thus normally causes a lot of spatters. Power Focus Power Focus Arc Specifications The Power Focus arc improves all the three arc phases. In short arc we obtain an extremely stable and viscous arc with very linear transfer and with TOTAL ABSENCE OF SPATTERS. In globular by Power Focus the arc maintains a very stable and ordered spatters transfer, as a result of this, it is possible to obtain a very regular weld. Specifications of Standard Arc In case of butt weld, if the plates caulker presents narrow angles, the standard arc has the tendency to get out from the caulker and to focus only on one of the two plate corners. In this situation, it is normally necessary to increase the caulker s angle degree (during the preparation) with consequent need of more filling passes. Power Focus Arc Specifications On the butt welding applications the Power Focus Arc keeps on staying concentrated in the exact middle of the caulker, so that full penetration is granted. In this way, it is possible to work on very narrow caulkers, which demands less mechanical preparation and of course, also less filling passes. 8 Layers 5 Layers Differences between Power Focus and Standard Arc Standard Power Focus Penetration by Power Focus Beyond a deeper penetration (see the picture), a significant difference is also to be found on the heated affected zone s extension (HAZ). This area is by Power Focus mode reduced, because of the higher execution s speed. Penetration by Power Focus on a T joint (10 mm thickness), when welded on the two sides, it comes up to interesect crossing. Thickness 8mm Angle 30 No gap between edges

7 MicroPulse 302MFK Easy setting of welding parameters Front Panel MicroPulse 302MFK Encoder Last measurement hold Led Arc lenght adjustment General alarm Led Synergic management key Menu Function Key Parameter Selection Button Micro Pulse 302 MFK Output voltage Led Wire Feeding push button Test-Gas push button Menu Exit Button Process selection 2stroke 4stroke 3level push button Custom memory (Job) push button Panel Digimanager Torch Configurations Down Button Up Button Parameter Selection Button MicroPulse 302MFK + Cooling Unit C.U.11 MicroPulse 302MFK + Cooling Unit C.U.11 + Trolley 03 REMOTE CONTROLS RC 04 Double potentiometer RC 05 Single Up & Down RC 06 Double Up & Down

8 MicroPulse 302 MFK 3x400Vac ± 50-60Hz 16A MIG-MAG TIG - WIG MMA % 40 C 35% 60% 100% 50% 60% 100% 40% 60% 100% 300A 230A 200A 250A 240A 210A 250A 220A 190A % RT - 60% 100% % % - 300A 250A A A 20A - 300A 5A - 250A 5A - 250A 11/60V 10,3KVA -9,7KW 23S 560 x 280 x 390mm 24,0Kg P1 l/min PMAX l/min PMAX C.U.11 1x400Vac ± 50-60Hz 0,76kW 2.8kW 0,43MPa 4.5l x 290 x 240mm 18,0Kg EN /10 EN Distributor WECO srl Via S. Antonio 22 - Loc. Belvedere Tezze sul Brenta (Vicenza) - Italy Tel fax vendite@weco.it -