SVENSK STANDARD SS-EN ISO 1127

Size: px

Start display at page:

Download "SVENSK STANDARD SS-EN ISO 1127"

Georgina Davis
6 years ago
Views:

1 SVENSK STANDARD SS-EN ISO 1127 Handläggande organ Fastställd Utgåva Sida MATERIAL- OCH MEKANSTANDARDISERINGEN, MMS (1+9) SIS FASTSTÄLLER OCH UTGER SVENSK STANDARD SAMT SÄLJER NATIONELLA, EUROPEISKA OCH INTERNATIONELLA STANDARDPUBLIKATIONER Stainless steel tubes Dimensions, tolerances and conventional masses per unit length (ISO 1127:1992) Rostfria stålrör Dimensioner, toleranser och viktuppgifter (ISO 1127:1992) The European standard EN ISO 1127:1996 has the status of a Swedish Standard. This document contains the official English version of EN ISO 1127:1996. Swedish Standard corresponding to documents referred to in this Standard are listed in Catalogue of Swedish Standards, issued by SIS. The Catalogue lists, with reference number and year of Swedish approval, International and European Standards approved as Swedish Standards as well as other Swedish Standards. Europastandarden EN ISO 1127:1996 gäller som svensk standard. Detta dokument innehåller den officiella engelska standarden EN ISO 1127:1996. Motsvarigheten och aktualiteten i svensk standard till de publikationer som omnämns i denna standard framgår av Katalog över svensk standard, som ges ut av SIS. I katalogen redovisas internationella och europeiska standarder som fastställts som svenska standarder och övriga gällande svenska standarder. ICS Standarder kan beställas hos SIS som även lämnar allmänna upplysningar om svensk och utländsk standard. Postadress: SIS, Box 6455, STOCKHOLM Telefon: Telefax: Upplysningar om sakinnehållet i standarden lämnas av MMS. Telefon: Telefax: Prisgrupp N Tryckt i december 1996

3 EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN ISO 1127 April 1996 ICS Descriptors: piping, stainless steels, austenitic steels, ferritic steels, martensitic steels, steel tubes, dimensions, dimensional toelrances, linear density English version Stainless steel tubes Dimensions, tolerances and conventional masses per unit length (ISO 1127:1992) Tubes en acier inoxydable Dimensions, tolérances et masses linéiques conventionelles (ISO 1127:1992) Nichtrostende Stahlrohre Masse, Grenzabmasse und längenbezogene Masse (ISO 1127:1992) This European Standard was approved by CEN on CEN members are bound to comply with the CEN/CENELEC Internal Regualtions which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. The European Standards exist in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comité Européen de Normalisation Europäisches Komitee für Normung Central Secretariat: rue de Stassart 26, B-1050 BRUSSELS 1996 Copyright reserved to CEN members Ref. No. EN ISO 1127:1996 E

4 Page 2 EN ISO 1127:1996 Provläsningsexemplar / Preview Stainless steel tubes Dimensions, tolerances and conventional masses per unit length 1 Scope This International Standard specifies the diameters, thicknesses, tolerances and conventional masses per unit length of stainless steel tubes. 4.1 See Tolerances on outside diameter table 1. Table 1 Tolerances on outside diameter 2 Normative reference The following standard contains provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the edition indicated was valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent edition of the standard indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 5252:1991, Steel tubes Tolerance systems. The tolerances on outside diameter include ovality. 4.2 Tolerances on thickness See table 2. 3 Dimensions Table 2 Tolerances on thickness The outside diameters and thicknesses of the tubes specified in this International Standard have been selected from ISO If thicknesses greater than 14,2 mm are needed, they should be chosen from ISO Tolerances The tolerances permitted on the outside diameter and thickness of the tubes result from the method of manufacture, the steel types and the heat trealment. The tolerances shall be selected from the values given in tables 1 and 2. The tolerances on thickness include eccentricity.

5 Page 3 EN ISO 1127: Other tolerances masses given in ISO 4200 multiplied by a factor of 1,015, This factor assumes an average density for For tolerances on dimensions other than outside di- these tubes of 7,97 kg/dm 3, ameter and thickness, reference shall be made to ISO The conventional masses per unit length given in table 4 for ferritic and martensitic stainless steel 5 Conventional masses per unit length tubes are the masses given in ISO 4200 multiplied by a factor of 0,985. This factor assumes an average The conventional masses per unit length given in density for these tubes of 7,73 kg/dm 3. table 3 for austenitic stainless steel tubes are the

6 Page 4 EN ISO 1127:1996 Provläsningsexemplar / Preview (Blank page)

SVENSK STANDARD SS-EN 1910

SVENSK STANDARD SS-EN 1910 Handläggande organ Fastställd Utgåva Sida Byggstandardiseringen, BST 2000-07-28 1 1 (1+9) Copyright SIS. Reproduction in any form without permission is prohibited. Wood and parquet