Diamond Chrome Plating Inc. Chemical Processing

Transcription

1 This certificate is granted and awarded by the authority of the Nadcap Management Council to: Diamond Chrome Plating Inc 604 S. Michigan Ave Howell, MI United States This certificate demonstrates conformance and recognition of accreditation for specific services, as listed in on the Qualified Manufacturers List (QML), to the revision in effect at the time of the audit for: Chemical Processing Certificate Number: Expiration Date: 30 April 2019 Joseph G. Pinto Executive Vice President and Chief Operating Officer Performance Review Institute (PRI) 161 Thorn Hill Road Warrendale, PA

2 Supplier Details I eauditnet Page 1 of 2 Search Results Supplier name: Diamond Chrome Plating Inc Active Suppliers: True Audit Program: Nadcap Phone: , Fax: The location reflects the Supplier's current location and may not reflect the accredited address if the supplier has moved. The accredited locations are displayed with the accreditation below. Show all scopes CP (Chemical Processing) Issue Date Expiry Date 21-Aug-17 Show scopes 30-Apr-19 Supplier has merit for above audit 16-Jul-16 Show scopes 31-0ct-17 ote: The specifications referenced herein have been submitted by the supplier as applicable to the audit scope. The audit process includes a sample of job audits from the listed specifications to verify compliance to defined requirements. Verification that the requirements of any given specification have been met by a su lier is not assured, sub ect to the constraints of the audit sam le. 8/21/2017

3 SCOPE OF ACCREDITATION Chemical Processing Diamond Chrome Plating Inc 604 S. Michigan Ave Howell, MI This certificate expiration is updated based on periodic audits. The current expiration date and scope of accreditation are listed at: - Online QML (Qualified Manufacturer Listing). In recognition of the successful completion of the PRI evaluation process, accreditation is granted to this facility to perform the following: AC7108 Rev H - Nadcap Audit Criteria for Chemical Processing (to be used on audits on/after 5 June 2016) AC7108/04 Solution Analysis and Testing AC7108/4 must also be selected AC7108/07 Vacuum Cadmium and Aluminum Ion Vapor Deposition AC7108/7 must also be selected AC7108/09 Electroplating and Electroforming AC7108/9 must also be selected AC7108/10 Electroless Plating AC7108/10 must also be selected AC7108/12 Acid Cleaning, Descaling, Passivation and Electropolishing AC7108/12 must also be selected AC7108/13 Brush Anodizing and Plating AC7108/13 must also be selected AC7108/14 Stripping of Coatings AC7108/14 must also be selected General Cleaning and Pre Cleaning Alkaline Cleaning (If Titanium Alkaline Cleaning is also carried out then please check Chemical Cleaning Titanium Cleaning Alkaline also) Solvent Cleaning Ovens Used for Thermal Treatments at a Set Point above 250 F Ovens for Thermal Treatments with a set point at or below 250ºF (121ºC) or for Miscellaneous Heating Processes, e.g. Part Drying. Stripping of Coatings Inorganic Coatings Other Stripping AC7108/4 Rev B - Nadcap Audit Criteria for Solution Analysis and Testing in Support of Chemical Processing to AC7108 (To Be Used On Audits Conducted On Or After June 5, 2016) Solution Analysis In Support of AC7108 t-frm Jun-10

4 Diamond Chrome Plating Inc #2 Howell, MI Testing Performed Internally In Support of the Chemical Process Accreditation B05 Salt Spray Testing In Support of AC7108 B10 Adhesion Testing (Adhesion Tape Testing) In Support of AC7108 B11 Adhesion Testing (Scratch and Chisel Test) In Support of AC7108 B12 Adhesion Testing (Bend Test) In Support of AC7108 B14 Conductivity Testing In Support of AC7108 B16 Coating Thickness Measurement In Support of AC7108 B20 Porosity Testing In Support of AC7108 B23 Other Testing In Support of AC7108 AC7108/7 Rev B - Nadcap Audit Criteria for Vacuum Cadmium Deposition (to be used on audits on/after 5 June 2016) As Coated With supplementary chromate treatment Vacuum Cadmium Other AC7108/9 - Nadcap Audit Criteria for Electroplating and Electroforming (to be used on audits on/after 5 June 2016) Electroplating Alloy Plating Other Alloy Plating Cadmium Plating Other Cadmium Plating Chromium Plating Other Chromium Plating Nickel Plating Other Nickel Plating AC7108/10 - Nadcap Audit Criteria for Electroless Plating (to be used on audits on/after 5 June 2016) Nickel Other Nickel AC7108/12 - Nadcap Audit Criteria for Acid Cleaning, Descaling, Passivation and Electropolishing (to be used on audits on/after 5 June 2016) Passivation Other Passivation AC7108/13 - Nadcap Audit Criteria for Brush Anodizing and Plating (to be used on audits on/after 5 June 2016) t-frm Jun-10

5 Diamond Chrome Plating Inc #3 Howell, MI Brush Plating Other Brush Plating AC7108/14 - Nadcap Audit Criteria for Stripping of Coatings as a Sub-Contract Process (Only select AC7108/14 if stripping is done as an overhaul process or as a sub-contract process. It is not required for internal rework.) t-frm Jun-10

6 Supplier Details I eauditnet Page 1 of 2 CP (Chemical Processing) Issue Date Expiry Date 21-Aug Apr-19 Hide scopes Supplier has merit for above audit AC7108/14 - Nadcap Audit Criteria for Stripping of Coatings as a Sub-Contract Process (Only select AC7108/14 if stripping is done as an overhaul process or as a sub-contract process. It is not required for internal rework.) AC7108/4 Rev B - Nadcap Audit Criteria for Solution Analysis and Testing in Support of Chemical Processing to AC7108 (To Be Used On Audits Conducted On Or After June 5, 2016) 4 Testing Performed Internally In Support of the Chemical Process Accreditation Conductivity Testing In Support of AC Coating Thickness Measurement In Support of AC Porosity Testing In Support of AC Salt Spray Testing In Support of AC Other Testing In Support of AC Adhesion Testing (Adhesion Tape Testing) In Support of AC Adhesion Testing (Bend Test) In Support of AC Adhesion Testing (Scratch and Chisel Test) In Support of AC7108 4Solution Analysis In Support of AC7108 AC7108/9 - Nadcap Audit Criteria for Electroplating and Electroforming (to be used on audits on/after 5 June 2016) 4Electroplating 4Alloy Plating 40ther Alloy Plating 4,info onl;,: MIL-STD Cadmium Plating 4(info only AMS (info onlyjams (info only~ms (info onlyrms-qq-p-416 4(info only t,ed-qq- P info onlyjmil-std-870 '-+Other Cadmium Plating 4Nickel Plating 4 info only t;ms-qq-n-290 '-+(info onlyyf.ms info onlyjfed-qq-n-290 '-+Other Nickel Plating '-+(info only MIL-STD-868 4i1 info only!ams Chromium Plating '-+(info only)ams-qq-c-320 '-+ info only~fed-qq-c ther Chromium Plating :...(info only MIL-STD-1501 :...(info only),ams 2406 :...(info onlyj,ams 2438 '-+~ info only]ams 2460 AC7108/13 - Nadcap Audit Criteria for Brush Anodizing and Plating (to be used on audits on/after 5 June 2016)... Brush Plating 40ther Brush Plating i..j(info onl dmil-std-865 AC7108/10 - Nadcap Audit Criteria for Electroless Plating (to be used on audits on/after 5 June 2016) 4Nickel '-+' in o on!ams 2404 https :// eauditnet/ean/ qml/ qm1search.htm?industry Id= 1 8/21/2017

7 Supplier Details I eauditnet Page 2 of2 '-+Other Nickel "" J(info only)mil-c ' info onlt!ams-c AC7108/12 - Nadcap Audit Criteria for Acid Cleaning, Descaling, Passivation and Electropolishing (to be used on audits on/after 5 June 2016) '-+Passivation... other Passivation '-+ info only)fed-qq-p-35 '-+(info only))astm A967 ~ info only~tms-qq-p-35 '-+ info onltlams 2700 AC7108 Rev H - Nadcap Audit Criteria for Chemical Processing (to be used on audits on/after 5 June 2016) ;...Ovens Used for Thermal Treatments at a Set Point above 250 F ;...AC7108/13 - Brush Anodizing and Plating -AC7108/13 must also be selected '-+Ovens for Thermal Treatments with a set point at or below 250 F (121 C) or for Miscellaneous Heating Processes, e.g. Part Drying.... stripping of Coatings '-+Iner anic Coatings... info only_}jmil-std-871 (info only) '-+Other Stripping c..general Cleaning and Pre-Cleaning '-+Solvent Cleaning ;...Alkaline Cleaning (If Titanium Alkaline Cleaning is also carried out then please check Chemical Cleaning - Titanium Cleaning -Alkaline" also) c..ac7108/10 - Electroless Plating -AC7108/10 must also be selected '-+AC7108/09 - Electroplating and Electroforming - AC7108/9 must also be selected c..ac7108/04 - Solution Analysis and Testing - AC7108/4 must also be selected ;...AC7108/14 - Stripping of Coatings - AC7108/14 must also be selected L+AC7108/07 - Vacuum Cadmium and Aluminum Ion Vapor Deposition - AC7108/7 must also be selected c..ac7108/12 - Acid Cleaning, Descaling, Passivation and Electropolishing - AC7108/12 must also be selected AC7108/7 Rev B - Nadcap Audit Criteria for Vacuum Cadmium Deposition (to be used on audits on/after 5 June 2016) c..vacuum Cadmium i.+(info only]mil-c-8837 ' info onlyjams2426 c.. info onl U:AMS-C-8837 c..other... As Coated c..with supplementary chromate treatment https :// eauditnet/ ean/ qml/ qm1search.htm?industry Id= 1 8/21/2017