STAINLESS STEEL HYGIENIC, DECORATIVE AND EXTREMELY TOUGH

Transcription

1 STAINLESS STEEL HYGIENIC, DECORATIVE AND EXTREMELY TOUGH

2 STAINLESS STEEL RUST, ACID AND HEAT-RESISTANT STAINLESS STEEL SHEETS Clients from industry and trade have been using our experience and comprehensive stocks for more than 25 years. Important markets are the food industry, the domestic technology industry, engineering, the chemical and automotive industries as well as the medical industry. You will find the size and quality that you are looking for in the range of over 1,500 products that we always have in stock. You benefit from a logistically advantageous and concentrated range of products in one place. Should you prefer decorative finishes we surface-finish stainless steel sheets by grinding, brushing and coating on our own two high-performance processing lines. Stainless steel pipes as well as stainless steel, rolled or drawn, are also available with ground or polished surfaces. We use international contacts to realise special customer wishes in the field of coils and strips. cold-rolled sheet hot-rolled sheet Heat-resistant sheet pattern-rolled sheet Tear plate B (IIIc) 2R (IIId) ground brushed film 0.30 x 1,000 x 2, x 1,500 x 3,000 mm D (IIa) 2.00 x 1,000 x 2, x 1,500 x 3,000 mm B (IIIc) 2C (IIIs) 1D (IIa) 1C (Ic) 1.00 x 1,000 x 2, x 1,500 x 3,000 mm Linen Leather Rhombus Squares 5WL 0.50 x 1,000 x 2, x 1,500 x 3,000 mm Mandorla 3.00 x 1,000 x 2, x 1,500 x 3,000 mm Processing Grinding Grain 80 to 400 Brushing Grinding + Brushing Film coating max. width 1,500 mm max. length 4,500 mm Material thickness mm Second choice second choice sheets second choice wide coils and strips third coice sheet and coilends

3 PROCESSING We can realise your desired finish with our processing machines. Grinding with grain mm Brushing mm Duplo ground / microlon ground (Grinding and brushing) mm Custom grinding to customer s specification/ pattern mm Protective film coating mm also available with two-sided finishing Max. width 1,500 mm Max. length 4,500 mm We can grind/brush stainless steel plate and stainless steel perforated plate (grease-free) Film coating is possible with Stainless steel plate Aluminium plate Perforated plate (grease-free) cold-rolled/galvanized plate (clean/grease-free) Brass, copper, Hastelloy, zinc... Synthetic plates Hire work: we will also carry out this processing on your goods! Work done at short notice good value processing modern processing and warehousing technology Film Type Usage/Characteristics UV-protection Description 100 my laser film (standard NC 4224 or Laser cutting; heavy load Y top white bottom black; blue stripes on our warehouse stocks) PF 564C high adhesiveness and longitudinal arrows 90 my film NC 4204 white heavy load; medium adhesiveness N white; blue longitudinal stripes 80 my film NC 4223 or heavy load Y top white bottom black PF 562C medium adhesiveness blue longitudinal stripes 70 my film NC 4504 heavy load; medium adhesiveness N blue-transparent 60 my film NC 4105 low load; low adhesiveness N blue-transparent 50 my film NC 4951 acrylic glue for brass and copper N blue-transparent medium load; medium adhesiveness STAINLESS STEELS/HEAT-RESISTANT STEELS Chemical composition Mechanical characteristics at room temperature Comparison with various norms Mate- Structure Code name C Si Mn Cr Mo Ni Other Delivery 0,2% - Tensile Breaking Scale AISI GOS rial- % % % % % % % condition proof- strength elongation resistance USA GUS No. K= cold- stress in air max. max. max. max. rolled Rp 0,2 Rm up to W= hot- N/mm 2 N/mm 2 % C rolled min. min. Rustfree steel Ferritic X2CrNi N: K S40977 W Ferritic X6Cr K Ch17 W Martensitic X46Cr K max (420) 40Ch13 W max Austenitic X5CrNi N: 0.11 K Ch18N10 W Austenitic X2CrNi N: 0.11 K L 03Ch18N11 W Austenitic X2CrNi N: 0.11 K L 04Ch18N10 W Austenitic X10CrNi < K (301) W Austenitic X5CrNiMo K W Austenitic X2CrNiMo N: 0.11 K L W Austenitic X2CrNiMo N: 0.11 K L 03Ch17N14 W M Austenitic X2CrNiMoN N: K S31726 W Ferritic X2CrTiNb Ti: K S x C+0.30 Nb Ferritic X2CrTi x (C+N) Ti 0.65 K W Austenitic X1NiCrMoCu N: < 0.15 K N08904 Cu: W Austenitic X6CrNiTi x C < Ti < 0.70 K Ch18N10T W Austenitic X6CrNiMoTi x C < Ti < 0.70 K Ti 10 Ch17N13 W M 2 T Heat-resistant steel Austenitic X8CrNiTi x C Ti H 12 Ch18N10T Austenitic X15CrNiSi , Austenitic X8CrNi , /310S Austenitic X15CrNiSi ,150 No responsibility is taken for the correctness of these specifications, made in accordance with DIN EN or This page was made with the friendly help of ThyssenKrupp Nirosta. Other materials, special analyses on request.

4 FINISHES Execution and surface quality for plate and strip Abbre- Execution Surface quality / Note former viation designation 1C Warm-rolled, heat-treated, covered with mill scale I c not descaled for heat-resistant quality E Warm-rolled, heat-treated, Scale-free, mechanically descaled, e.g. by II a mechanically descaled grinding or blasting. 1D Warm-rolled, heat-treated, Scale-free, Standard for most warm-rolled IIa or pickled types of steel. Not as smooth as C2 or 2D or 2B. No.1 2H Cold-hardened Bright III a Cold recast to achieve greater hardness. 2C Cold-rolled, heat-treated, Smooth, with scale from heat treatment III s not descaled for heat-resistant quality D Cold-rolled, heat-treated, Smooth III b pickled Good reworkability, but not as smooth as 2B or 2R. 2B Cold-rolled, heat-treated, Smoother than 2D III c pickled, cold re-rolled Standard for most cold-rolled types of steel. 2R Cold-rolled, bright-annealed Smooth, bright, reflective IIId or Smoother and brighter than 2B. BA 2G Ground Grain between 80 and 400 IV available. 2J Brushed Smoother than ground. 2M Patterned Various patterns available, such as linen, leather, rhombus or squares. The back is smooth here Other patterns like 5WL are embossed. Special models Cold-rolled Warm-rolled Reference values: Thickness tolerances for cold-rolled plate and strip Thickness in mm Width in mm up to 1,000 ± 0.04 ± ± 0.05 ± ± 0.06 ± 0.07 ± 0.08 ± 0.09 ± 0.11 ± 0.13 ± 0.14 ± ,000-1,300 ± 0.04 ± 0.05 ± 0.05 ± 0.06 ± 0.07 ± 0.08 ± 0.09 ± 0.10 ± 0.12 ± 0.14 ± 0.15 ± 0.15 over 1,300 ± 0.06 ± 0.07 ± 0.08 ± 0.10 ± 0.11 ± 0.12 ± 0.14 ± 0.15 ± 0.16 * ± 0.03 ± 0.04 ± 0.04 ± 0.04 ± 0.05 ± 0.05 ± 0.06 ± 0.06 ± 0.07 ± 0.08 ± 0.09 ± 0.10 STAINLESS STEEL PIPES Profile pipe HF or WIG welded, non-brazed Square pipes 10 x 10 x x 200 x 5.00 mm Rectangular pipes 20 x 10 x x 100 x 5.00 mm Decoration and construction tubing DIN HF or WIG welded, non-brazed or brazed 6.00 x x 5.00 mm EN ISO 1127 Conduit pipes DIN WIG or laser welded, non-brazed or brazed 6.00 x x 5.00 mm EN ISO 1127 STRIPS/COILS/ZUSCHNITTE Product Cold-rolled strip Surface Thickness Width Warm-rolled strip Surface Thickness Width further options: B (IIIc) 2R (IIId) ground brushed film mm ,000 mm EN E (IIa) mm ,000 mm EN Slit strip for vehicle exhausts Decoiling of fixed dimension sheets Flat bars, cut, calibrated Roller aligned Aligned Precision strip in accordance with EN10258 STAINLESS STEEL BARS Flat rolled steel Round steel bar Railings Angels Square steel wire NOT JUST ROUND STAINLESS STEEL BRIGHT BARS Our bright steel range is comprehensive and thanks to exact tolerances ideal for use in industries where precision and surface quality are critical. Our advantage: the entire range is also available in stainless steel Cut corner, classic rolled or ground grain x x mm / HL 4 m oder 4-6 m DIN rolled or rolled/peeled mm / HL 4-6 m DIN Brushed or ground grain 240 Rund mm / HL 6 m DIN 668/ rolled 20 x 20 x x 100 x 10 mm / HL 6 m DIN rolled 20 x 150 mm / HL 4-6 m DIN 1014 All dimensions, materials and details can be found in the individual brochure Stainless steel, bright bars. For further information: vbl@holzrichter-stahl.de. brushed or ground Mandorla 5WL Linen (25) Rhombus (22) Squares (21) Leather (42) * These tolerances are possible for new production upon production of a complete coil.

5 ESSEN A42 A40 A43 BOCHUM A44 A45 DORTMUND HERDECKE A44 WITTEN A43 HERDECKE ISERLOHN A45 AS-- BARMEN SCHÜTZENSTR. AS-- WICHLINGHSN. AS- - OST 7 SCHÖNE- BECKERSTR. FRIEDRICH- ENGELS-ALLEE CARNAPER- STR. 7 SCHÖNEBECKER PLATZ Administration Office: Schönebecker Platz 11, D Wuppertal Supply and dispatch warehouse in the Loh industrial park Access via Schönebecker Straße Phone: +49 (0) Fax: +49 (0) YOUR CONTACTS:ÄN Angelika Bäcker Phone: +49 (0) , Fax: +49 (0) a.baecker@holzrichter-stahl.de Larissa Bergmann Phone: +49 (0) , Fax: +49 (0) l.bergmann@holzrichter-stahl.de Stefan Bergs Phone: +49 (0) , Fax: +49 (0) s.bergs@holzrichter-stahl.de Christian Martin Phone: +49 (0) , Fax: +49 (0) c.martin@holzrichter-stahl.de Wolfgang Matzolleck Phone: +49 (0) ; Fax: +49 (0) w.matzolleck@holzrichter-stahl.de Axel Sticher Phone: +49 (0) , Fax: +49 (0) a.sticher@holzrichter-stahl.de Sylvia Kroll Phone: +49 (0) , Fax: +49 (0) s.kroll@holzrichter-stahl.de Peter Holzrichter GmbH Postfach , D Wuppertal info@holzrichter-stahl.de Web: A company of the -Group