ArcelorMittal Dofasco Scrap Specifications and Requirements

Size: px
Start display at page:

Download "ArcelorMittal Dofasco Scrap Specifications and Requirements"

Transcription

1 ArcelorMittal Dofasco Scrap Specifications and Requirements Revision date: January 2017

2 Table of Contents Type of Scrap: Auto Cast (Brake Rotors and Drums)... 2 Type of Scrap: Bushelling... 4 Type of Scrap: Bushelling - Shredded... 6 Type of Scrap: Cold Iron (High Sulphur); Cold Iron (Low Sulphur)... 8 Type of Scrap: Customer Scrap Type of Scrap: Dealer Bundles (#1.5) Type of Scrap: No.1 Heavy Melt Type of Scrap: Hot Briquetted Borings (HBB) Type of Scrap: Industrial Bundles Type of Scrap: Pit Scrap Type of Scrap: Plate and Structural Type of Scrap: Post-Consumer Steel Can Bundles Type of Scrap: Rail Wheels and Cut Rail Type of Scrap: Shredded Scrap Type of Scrap: Turnings - Briquetted Type of Scrap: Turnings - Loose Appendix A: Instructions for Displacement Tests for Determining the Metallic Content of Reclaimed Steel Scrap NOTE: Fe Yield in Use (%) = Tapped Steel Weight/Charge Material Weight 1

3 Type of Scrap: Auto Cast (Brake Rotors and Drums) Material Description: Exclusively include cast iron brake rotors and drums. Sizing: Not to exceed 2 in any direction Exclusions (must not contain): - Non Ferrous material and Non Metallic parts - Mill Scale, Grinding Swarf, Ammunition, Nuts, Bolts, Grinding Balls, Nails, Rebar, Dirt, Wood, Oil, Grease, Rags, Plastics, Insulation, Municipal Scrap, Excessive Rust/Corrosion, Sealed Containers - Electrical Components - Torque Converters and Exhaust Manifolds - Machine Castings and Engine Blocks Chemistry: Minimum Fe Yield in Use: 87% Cu P S 0.20 Max Max 0.15 Max 2

4 Type of Scrap: Auto Cast (Brake Rotors and Drums) Example of acceptable material: 3

5 Type of Scrap: Bushelling Material Description: Clean, prompt, alloy free industrial sheet steel scrap, clips and punching s. May include galvanized steel scrap. Material must not be stringy, tangled, bunched, or form a bird s nest. Up to 5% tubing allowed (based on volume, not weight of load). Must not be concentrated in one section of load. Sizing: 5 Spec: 60 x 24 Max; 3/8 thick Max 3 Spec: 36 x 24 Max; 1/2 thick Max 1 Spec: 12 x 12 Max; 1/2 thick Max Minimum Thickness: 1/8 Density: 5 Spec: 40 lbs/ft 3 Min 3 Spec: 60 lbs/ft 3 Min 1 Spec: 100 lbs/ft 3 Min Exclusions (must not contain): - Non Ferrous material and Non Metallic parts - Mill Scale, Grinding Swarf, Ammunition, Nuts, Bolts, Grinding Balls, Nails, Rebar, Dirt, Wood, Oil, Grease, Rags, Plastics, Insulation, Municipal Scrap, Excessive Rust/Corrosion, Sealed Containers - Obsolete scrap of any kind - Painted material - Fencing - Floor Grating - Copper coated material; tin bearing scrap - Slitter Coils, Mandrel Coils Chemistry: Minimum Fe Yield in Use: 90% Cu P Pb S 0.12 Max 0.03 Max Max 0.03 Max 4

6 Type of Scrap: Bushelling Example of acceptable material: 5

7 Type of Scrap: Bushelling - Shredded Material Description: Clean, prompt, alloy free industrial sheet steel scrap, clips and punching s. May include galvanized steel scrap. Product must be magnetically separated, fragmentized clean product. Sizing: 6 Max Density: 70 lbs/ft 3 Min Exclusions (must not contain): - Non Ferrous material and Non Metallic parts - Mill Scale, Grinding Swarf, Ammunition, Nuts, Bolts, Grinding Balls, Nails, Rebar, Dirt, Wood, Oil, Grease, Rags, Plastics, Insulation, Municipal Scrap, Excessive Rust/Corrosion, Sealed Containers - Obsolete scrap of any kind - Painted material - Fencing - Copper coated material; tin bearing scrap Chemistry: Minimum Fe Yield in Use: 90% Cu P Pb S 0.12 Max 0.03 Max Max 0.03 Max 6

8 Type of Scrap: Bushelling - Shredded Example of acceptable material: 7

9 Type of Scrap: Cold Iron (High Sulphur); Cold Iron (Low Sulphur) Material Description: Cold Iron generated from an identifiable source which is processed to the specified physical requirements. AM Dofasco requires supplier to develop and submit a quality control program that will be adhered to when supplying Cold Iron. Quality program to include at minimum: identification of source of material, chemical testing results for material. Sizing: 18 x 18 x 6 Max 3 Min Exclusions (must not contain): - Non Ferrous material and Non Metallic parts - Mill Scale, Grinding Swarf, Ammunition, Nuts, Bolts, Grinding Balls, Nails, Rebar, Dirt, Wood, Oil, Grease, Rags, Plastics, Insulation, Municipal Scrap, Excessive Rust/Corrosion, Sealed Containers - Slag and/or Fines Chemistry: Minimum Fe Yield in Use: 80% High Sulphur Low Sulphur C 4.5 Max 4.5 Max P 0.04 Max 0.04 Max Pb Max Max S 0.08 Max 0.04 Max 8

10 Type of Scrap: Cold Iron (High Sulphur); Cold Iron (Low Sulphur) Example of acceptable material: 9

11 Type of Scrap: Customer Scrap Material Description: Slitter coils, Mandrel Coils and Tube scrap generated from the manufacturing sector. To ensure coil stays intact and to prevent unraveling, Slitter coils and Mandrel coils are to be secured with a minimum of: 1 iron band around O.D. of coil; 3 iron bands through eye of coil, separated evenly and must be secure and not move once affixed. Tube scrap and Slitter coils / Mandrel coils are to be delivered as exclusively that material type only. Supplier must schedule each load on day shift only with AMD scrap handling prior to delivery. Sizing: Tube Scrap: 5 max length Max Coil weight: 4,000 lbs Max Coil height: 42 ; Max Coil width: 24 Density: 40 lb/ft 3 min Exclusions (must not contain): - Non Ferrous material and Non Metallic parts - Mill Scale, Grinding Swarf, Ammunition, Nuts, Bolts, Grinding Balls, Nails, Rebar, Dirt, Wood, Oil, Grease, Rags, Plastics, Insulation, Municipal Scrap, Excessive Rust/Corrosion, Sealed Containers - Obsolete scrap of any kind - Painted material Chemistry: Minimum Fe Yield in Use: 90% Cu P Pb S 0.12 Max 0.03 Max Max 0.03 Max 10

12 Type of Scrap: Customer Scrap Example of acceptable material: 11

13 Type of Scrap: Dealer Bundles (#1.5) Material Description: New and old steel sheet scrap, clippings, steel racking, skeleton plate hydraulically compressed into a bundle. Galvanize steel scrap, tube and pipe is acceptable. Up to 10% Rebar allowed (based on volume, not weight of load). Must not be concentrated in one section of load. Bundle must maintain its form when handled multiple times. Sizing: 36 x 36 x 36 Max Density: 90 lb/ft 3 Min Exclusions (must not contain): - Non Ferrous material and Non Metallic parts - Mill Scale, Grinding Swarf, Ammunition, Nuts, Bolts, Grinding Balls, Nails, Dirt, Wood, Oil, Grease, Rags, Plastics, Insulation, Municipal Scrap, Excessive Rust/Corrosion, Sealed Containers - Copper coated material; Tin bearing scrap - Excessive painted material - Coated fencing Chemistry: Minimum Fe Yield in Use: 86% Cu P Pb S 0.25 Max 0.05 Max 0.02 Max 0.05 Max 12

14 Type of Scrap: Dealer Bundles (#1.5) Example of acceptable material: 13

15 Type of Scrap: No.1 Heavy Melt Material Description: Clean, mild carbon steel scrap, obsolete and new. May contain auto/truck rims, must have balancing lead weights removed. May contain heavy walled pipe; pipe with 8 O.D. and up must be split. Hydraulic cylinders must be separated from the ram. Up to 10% Rebar allowed (based on volume, not weight of load). Must not be concentrated in one section of load. Up to 10% of the following automotive only is allowed: Gears, Axles, Shafts, Bearings, Springs (based on volume, not weight of load). Must not be concentrated in one section of load. Sizing: 48 x 24 Max thick Density: 45 lbs/ft 3 Min Exclusions (must not contain): - Non Ferrous material and Non Metallic parts - Mill Scale, Grinding Swarf, Ammunition, Nuts, Bolts, Grinding Balls, Nails, Dirt, Wood, Oil, Grease, Rags, Plastics, Insulation, Municipal Scrap, Excessive Rust/Corrosion, Sealed Containers - Vehicle body parts not mentioned in Material Description including, but not limited to: Gas Tanks, Torque Converters, Cables, Transmissions, Electrical Panels, Motors and Motor Blocks - Copper coated material; Tin bearing scrap - Domestic appliances - Cast Iron Chemistry: Minimum Fe Yield in Use: 86% Cu 0.25 Max Cr 0.15 Max P 0.05 Max Pb 0.02 Max S 0.05 Max 14

16 Type of Scrap: No.1 Heavy Melt Example of acceptable material: 15

17 Type of Scrap: Hot Briquetted Borings (HBB) Material Description: The hot briquetting process uses 95% cast iron borings and 5% steel turnings as feedstock and heats and bonds the iron particles with no binders and melts out the oils and moisture. Sizing: 5.25 x 2.5 x 1.8 Max Density: 375 lb/ft 3 Min Exclusions (must not contain): - Non Ferrous material and Non Metallic parts - Mill Scale, Grinding Swarf, Ammunition, Nuts, Bolts, Grinding Balls, Nails, Rebar, Dirt, Wood, Oil, Grease, Rags, Plastics, Insulation, Municipal Scrap, Excessive Rust/Corrosion, Sealed Containers - Fines Chemistry: Minimum Fe Yield in Use: 86% C 4 Max Cu 0.25 Max P 0.05 Max Pb Max S 0.08 Max 16

18 Type of Scrap: Hot Briquetted Borings (HBB) Example of acceptable material: 17

19 Type of Scrap: Industrial Bundles Material Description: New production, low carbon steel sheet scrap, clippings, skeleton scrap or tube hydraulically compressed into a bundle. Bundle must maintain its form when handled multiple times. Sizing: 36 x 24 x 24 Max Density: 100 lb/ft 3 Min Exclusions (must not contain): - Non Ferrous material and Non Metallic parts - Mill Scale, Grinding Swarf, Ammunition, Nuts, Bolts, Grinding Balls, Nails, Rebar, Dirt, Wood, Oil, Grease, Rags, Plastics, Insulation, Municipal Scrap, Excessive Rust/Corrosion, Sealed Containers - Obsolete scrap of any kind - Painted material - Fencing - Copper coated material; Tin bearing scrap Chemistry: Minimum Fe Yield in Use: 88% Cu 0.12 Max P 0.03 Max Pb Max S 0.03 Max 18

20 Type of Scrap: Industrial Bundles Example of acceptable material: 19

21 Type of Scrap: Pit Scrap Material Description: Pit Scrap generated from identifiable source which is processed to the aimed physical requirements. Irregular shaped pieces of crushed and magnetized steel that has been separated from steelmaking slag. AM Dofasco requires supplier to develop and submit a quality control program that will be adhered to when supplying Pit Scrap. Quality program to include at minimum: identification of source of material, water displacement test results to identify metallic iron content. Sizing: 18 x 18 x 6 Max 3 Min Exclusions (must not contain): - Non Ferrous material and Non Metallic parts - Mill Scale, Grinding Swarf, Ammunition, Nuts, Bolts, Grinding Balls, Nails, Rebar, Dirt, Wood, Oil, Grease, Rags, Plastics, Insulation, Municipal Scrap, Excessive Rust/Corrosion, Sealed Containers - Fines - Ladle nozzles, Refractory nozzles, Gate plates Chemistry: Minimum Fe Yield in Use: 74% Cu 0.15 Max P 0.05 Max Pb Max S 0.04 Max Minimum Fe based on Water Box Displacement Testing: 85% Refer to Appendix A: Instructions for Displacement Tests for Determining the Metallic Content of Reclaimed Steel Scrap 20

22 Type of Scrap: Pit Scrap Example of acceptable material: 21

23 Type of Scrap: Plate and Structural Material Description: Alloy free cut plate and structural shapes, obsolete and new. Material lies flat in load. May contain some heavy walled pipe any pipe with greater than 8 O.D. must be split. Sizing: 48 x 24 Max thick Density: 50 lbs/ft 3 Min Exclusions (must not contain): - Non Ferrous material and Non Metallic parts - Mill Scale, Grinding Swarf, Ammunition, Nuts, Bolts, Grinding Balls, Nails, Rebar, Dirt, Wood, Oil, Grease, Rags, Plastics, Insulation, Municipal Scrap, Excessive Rust/Corrosion, Sealed Containers - Vehicle body parts such as Wheel Rims, Gears, Gas Tanks, Axles, Cam Shafts, Bearings, Torque Converters, Cables, Springs, Transmissions, Electrical Panels, Motors and Motor Blocks - Copper coated material; Tin bearing scrap - Cast Iron Chemistry: Minimum Fe Yield in Use: 86% Cu 0.25 Max P 0.04 Max Pb Max S 0.04 Max 22

24 Type of Scrap: Plate and Structural Example of acceptable material: 23

25 Type of Scrap: Post-Consumer Steel Can Bundles Material Description: Clean, hydraulically compacted, 100% post-consumer steel cans (beverage and food). May contain empty aerosol cans void of product. May contain paint cans with their lids removed and no liquid paint present. May include spiral wound paper containers with steel bottoms. Bundle must maintain its form when handled multiple times. Sizing: 36 x 36 x 36 Max Density: 75 lb/ft 3 Min Exclusions (must not contain): - Non Ferrous material and Non Metallic parts - Mill Scale, Grinding Swarf, Ammunition, Nuts, Bolts, Grinding Balls, Nails, Rebar, Dirt, Wood, Oil, Grease, Rags, Plastics, Insulation, Municipal Scrap, Excessive Rust/Corrosion, Sealed Containers - Copper coated material; Tin bearing scrap Chemistry: Minimum Fe Yield in Use: 78% Cu 0.15 Max Sn 0.3 Max P 0.04 Max Pb Max S 0.04 Max 24

26 Type of Scrap: Post-Consumer Steel Can Bundles Example of acceptable material: 25

27 Type of Scrap: Rail Wheels and Cut Rail Material Description: Solid cast steel, forged, pressed and/or rolled steel car and/or locomotive wheels. Railroad Crops. Sizing: Cut Rail: 4 length Max Wheels: 42 diameter Max Density: 75 lb/ft 3 Min Exclusions (must not contain): - Non Ferrous material and Non Metallic parts - Mill Scale, Grinding Swarf, Ammunition, Nuts, Bolts, Grinding Balls, Nails, Rebar, Dirt, Wood, Oil, Grease, Rags, Plastics, Insulation, Municipal Scrap, Excessive Rust/Corrosion, Sealed Containers Chemistry: Minimum Fe Yield in Use: 88% Cu 0.15 Max P 0.15 Max S Max 26

28 Type of Scrap: Rail Wheels and Cut Rail Example of acceptable material: 27

29 Type of Scrap: Shredded Scrap Material Description: Magnetically separated fragmentized clean, alloy free, mild steel scrap produced from unprepared #1 heavy melt and demolition steel scrap, car hulks, miscellaneous baling and sheet material. Shredder feedstock to contain minimal amount of white goods. Up to 5% Rebar allowed (based on volume, not weight of load). Must not be concentrated in one section of load. All suppliers of shredded material must register and participate in Switch Out. Switch Out is a national program dedicated to removing, collecting and managing automotive mercury switches found in convenience lighting and ABS sensors. For more information, please visit the following website: Switch Out: Sizing: 6 Max Density: 70 lbs/ft 3 Min Exclusions (must not contain): - Non Ferrous material and Non Metallic parts - Mill Scale, Grinding Swarf, Ammunition, Nuts, Bolts, Grinding Balls, Nails, Dirt, Wood, Oil, Grease, Rags, Plastics, Insulation, Municipal Scrap, Excessive Rust/Corrosion, Sealed Containers - Electrical motors, Armatures - Copper coated material; Tin bearing scrap - Turnings, Borings, PC Cans, Tire Wire, Rebar, Oil Filters, Upholstery, Fluff - Shredded product must be free of mercury, mercury switches, closed containers of any sort including hydraulic cylinders, shock absorbers, closed pipes, electrical transformers and/or other components that are suspect of having contained PCB s and CFC s. Chemistry: Minimum Fe Yield in Use: 86% Cu 0.20 Max P 0.04 Max Pb Max S 0.04 Max 28

30 Type of Scrap: Shredded Scrap Example of acceptable material: 29

31 Type of Scrap: Turnings - Briquetted Material Description: Hydraulically cold pressed steel turnings. Strength of briquette should be sufficient such that briquette does not break during transportation, unloading or normal handling by magnet. Sizing: Briquetted to 6 max Density: 180 lb / ft 3 min Exclusions (must not contain): - Non Ferrous material and Non Metallic parts - Mill Scale, Grinding Swarf, Ammunition, Nuts, Bolts, Grinding Balls, Nails, Rebar, Dirt, Wood, Oil, Grease, Rags, Plastics, Insulation, Municipal Scrap, Excessive Rust/Corrosion, Sealed Containers - Fines Chemistry: Minimum Fe Yield in Use: 80% C 2 Max Cu 0.25 Max P 0.05 Max Pb Max S 0.08 Max 30

32 Type of Scrap: Turnings - Briquetted Example of acceptable material: 31

33 Type of Scrap: Turnings - Loose Material Description: Clean, loose steel turnings from a known source, free of lumps, tangled or matted material. Density: 30 lb / ft 3 min Exclusions (must not contain): - Non Ferrous material and Non Metallic parts - Mill Scale, Grinding Swarf, Ammunition, Nuts, Bolts, Grinding Balls, Nails, Rebar, Dirt, Wood, Oil, Grease, Rags, Plastics, Insulation, Municipal Scrap, Excessive Rust/Corrosion, Sealed Containers Borings - Heavy oxidized turnings Chemistry: Minimum Fe Yield in Use: 80% C 2 Max Cu 0.25 Max P 0.05 Max Pb Max S 0.08 Max 32

34 Type of Scrap: Turnings - Loose Example of acceptable material: 33

35 Appendix A: Instructions for Displacement Tests for Determining the Metallic Content of Reclaimed Steel Scrap A representative sample is to be obtained from each railroad car or truck containing reclaimed scrap. These samples must contain the proper proportion of the light and heavy scrap and slag adhering scrap contained in each car, as accuracy of the results obtained depend to a large extent on the samples used for the test. The samples taken from the railroad cars or charging boxes should be dried or contain less than.5% moisture before being placed in a watertight container. The weight of the composite sample taken should be determined before the water is added, and again weighed after sufficient water is added to fully submerge the scrap. The water is added to displace the voids contained in the batch. (Do not measure or weigh until bubbling has ceased.) The weight of the water divided by pounds per cubic foot will equal the cubic feet of water contained in the box, and the total cubical content of the scrap and water (determined by actual measurements), less the cubic feet of water, results in the cubical content of this scrap. The theoretical weight of steel is determined by multiplying the cubic feet of scrap by the weight per cubic feet of 430 pounds for the density of steel. The difference in weight between the actual weight of the sample and the theoretical weight is divided by the difference in weight per cubic foot of steel and slag, the result being the cubic feet of material other than metal. The metallic content is then determined by deducting the cubic feet of other than metal from the total cubic feet of scrap in the box, the result of which is the cubic feet of solid metal, and which multiplied by the weight per cubic feet of 430 pounds for steel, which is then divided by the actual weight of the sample, results in the metallic content of the scrap. Procedure 1. A watertight container should be used, the size of which should be sufficiently large to contain scrap of maximum charging box size which is 3 6 (42 ) wide, 5 6 (66 ) long and 4 (48 ) deep (inside dimensions) or about 77 cubic feet. 2. Determine exact weight of box when empty. 34

36 3. Because the actual cubic content of the box cannot be calculated using the length times width times depth measurements, due to inside welds and distortion from handling, the average cubic foot per inch of depth of box is to be calculated. First, measure the depth of the box at all four (4) corners and divide by four. (4), to calculate the average box depth. Second, fill the box with water and determine weight of water added. Third, calculate the average depth of water by measuring down from top of box to the water at all four (4) corners and divide by four (4), then subtract that figure from the average box depth. Fourth, to determine the cubic feet of water, divide the weight of water per cubic foot (62.428). Fifth, divide cubic feet of water by average depth of water in inches to determine the cubic foot per inch of depth of box. The cubic foot per inch of depth of the box should be recalculated approximately once a year. 4. Fill box with representative samples of scrap. 5. Determine gross weight of box and scrap contained by weighing on suitable scale. 6. Fill box with water, completely submerging the scrap contained in the box to at least one to two inches. 7. Determine gross weight of scrap and water contained in box by again weighing on suitable scale. 8. Determine cubical content of the combined scrap and water in box by measuring from the water level to top the box at each corner and use average of the four (4) corners subtract from average depth of box. This figure then multiplied by the cubic foot per inch of depth (Step 3) equals the cubic content of scrap and water in box. 9. Calculate the weight of the water and the weight of the scrap in the box from actual scale weighing. 10. Calculate the cubic feet of water in the box by dividing the weight of the water contained in the box by pounds. 11. Calculate the cubic feet of scrap in box by deducting the cubic feet of water from the total cubic feet of scrap and water. 12. Calculate the theoretical weight of steel by multiplying the cubic feet (11) by 430 pounds per cubic feet. 35

37 13. Determine the cubic feet of other than metal in the sample by dividing the difference between the theoretical and the actual weight of the sample by 270 pounds ( ). 14. Calculate the metallic content of the scrap by deducting the cubic feet of other than metal (13) from the total cubic feet of scrap in box (11) the result of the which is the cubic feet of solid metal, and which, multiplied by the weight per cubic feet of 430 lbs for steel, and then divide that result by the actual weight of the sample, the result being the metallic content of the scrap. 36

Examples of the ferrous metals: Vehicle scrap metal Demolition Site scrap metal Metal off cuts from manufacturing industries

Examples of the ferrous metals: Vehicle scrap metal Demolition Site scrap metal Metal off cuts from manufacturing industries Schnitzer accepts all types of ferrous and non-ferrous metals. Ferrous Metals mostly contain Iron. They have small amounts of other metals or elements added, to give the required properties. Ferrous Metals

More information

EUROPEAN STEEL SCRAP SPECIFICATION. General Conditions applicable to all grades

EUROPEAN STEEL SCRAP SPECIFICATION. General Conditions applicable to all grades Bundesvereinigung Deutscher Stahlrecycling- und Entsorgungsunternehmen e.v. EUROPEAN STEEL SCRAP SPECIFICATION Version: June 1 st 1995 General Conditions applicable to all grades As is pratically achievable

More information

Material : Steel Scrap Grade : All SDI Part # N/A

Material : Steel Scrap Grade : All SDI Part # N/A Material : Steel Scrap Grade : All SDI Part # N/A Industry Id : ISRI # s: N/A A.K.A. : N/A Scope : The following general quality specifications apply to all scrap grades purchased by Steel Dynamics, Inc.

More information

FERROUS RAW MATERIALS MANUAL

FERROUS RAW MATERIALS MANUAL GERDAU MIDLOTHIAN, LP 300 WARD ROAD MIDLOTHIAN, TEXAS, 76065 (972) 775-8241 FERROUS RAW MATERIALS MANUAL PART 3 FERROUS RAW MATERIALSPECIFICATIONS Revision 16 Effective May 23, 2018 GERDAU Midlothian Grade

More information

Material Specifications

Material Specifications 1 Material Specifications 2 Policies and Procedures Supplier may not deviate from material specifications without prior written approval by authorized Procurement personnel. If material specifications

More information

EUROPEAN STEEL SCRAP SPECIFICATION

EUROPEAN STEEL SCRAP SPECIFICATION EUROPEAN STEEL SCRAP SPECIFICATION General Conditions applicable to all grades As it practically achievable in customary preparation and handling of the grade involved The definitions of this list of specifications

More information

Copyright by ATM Recyclingsystems GmbH Page 1 of 5. Post-consumer scrap (Old scrap) Nomenclature. Copper scrap in large pieces

Copyright by ATM Recyclingsystems GmbH Page 1 of 5. Post-consumer scrap (Old scrap) Nomenclature. Copper scrap in large pieces Post-consumer scrap (Old scrap) Copper scrap in large pieces Copper scrap in small pieces Mixed copper scrap Candy Dream Dream Sheets, punch scraps, slide bar, wires, pipes Sheets, rainwater gutters, water

More information

Chapter 73. Articles of iron or steel

Chapter 73. Articles of iron or steel Chapter 73 Articles of iron or steel Notes. 1.- In this Chapter the expression cast iron applies to products obtained by casting in which iron predominates by weight over each of the other elements and

More information

RATE OF DUTY UNIT(S) DESCRIPTION OF GOODS

RATE OF DUTY UNIT(S) DESCRIPTION OF GOODS 73.01 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel. 7301.10.00 Sheet piling 5% kg 7301.20.00 Angles,

More information

Scrap Management Plan

Scrap Management Plan CMC Steel Oklahoma Scrap Management Plan Revision 2.0 Effective January 1, 2019 Page 1 of 26 SCRAP MANAGEMENT PLAN TABLE OF CONTENTS INTRODUCTION. 3 GENERAL TERMS & CONDITIONS.. 4 GENERAL RAW MATERIALS

More information

Product list PRODUCT CATEGORIES ACCEPTED AT THE EVENT

Product list PRODUCT CATEGORIES ACCEPTED AT THE EVENT PRODUCT CATEGORIES ACCEPTED AT THE EVENT A) Producers, distributors, traders, service centres, agents, purchase groups and users of the following products: 1. Iron ores and derivatives 1.1. Magnetite 1.2.

More information

TABLE OF CONTENTS. Hot Roll (Angles, Beams, Channels, Flats, Squares, Rounds) 3. Pipe, Pipe Tube, Tube. Sheets & Plates

TABLE OF CONTENTS. Hot Roll (Angles, Beams, Channels, Flats, Squares, Rounds) 3. Pipe, Pipe Tube, Tube. Sheets & Plates DRI1529-McNeilus-Revised 12/12/05 12:18 PM Page 1 McNeilus Steel, Inc. TABLE OF CONTENTS Page Hot Roll (Angles, Beams, Channels, Flats, Squares, Rounds) 3 Cold Roll (Flats, Hex, Rounds) 17 Pipe, Pipe Tube,

More information

CMC STEEL ALABAMA RAW MATERIALS SPECIFICATION MANUAL

CMC STEEL ALABAMA RAW MATERIALS SPECIFICATION MANUAL Revision #5 - - 2 February 2009 CMC STEEL ALABAMA RAW MATERIALS SPECIFICATION MANUAL Table of Contents INTRODUCTION 1 GENERAL TERMS & CONDITIONS 2 GENERAL RAW MATERIALS SPECIFICATIONS 5 ENVIRONMENTAL ISSUES

More information

For Heavy-Duty, High-Volume Ferrous Separation

For Heavy-Duty, High-Volume Ferrous Separation For Heavy-Duty, High-Volume Ferrous Separation DEEP DRAW DRUM FOR MATERIAL RECOVERY FACILITY AUTOMOBILE SCRAP C&D RECYCLING MATERIAL RECOVERY FACILITIES COAL PROCESSING PLANTS FOUNDRIES STEEL AND SLAG

More information

IRON AND STEEL PRODUCTS

IRON AND STEEL PRODUCTS Announcement: Please be informed that the Fast Track Clearance facilities will expire on 21 st August 2013. In addition, with effective from 22 nd August 2013, all Certificate of Approval applications

More information

IRON, STEEL AND ALUMINIUM PRODUCTS

IRON, STEEL AND ALUMINIUM PRODUCTS IRON, STEEL AND ALUMINIUM PRODUCTS NO. PDK 2017 PDK 2012 DESCRIPTION OF GOODS 7207 Semi-finished products of iron or non-alloy steel. - Containing by weight less than 0.25% of carbon: 1 7207110000 720711000

More information

WHEN WASTE CEASES TO BE WASTE. The Case of Ferrous Scrap

WHEN WASTE CEASES TO BE WASTE. The Case of Ferrous Scrap EUROFER and EFR Elements to Progress the Discussion on WHEN WASTE CEASES TO BE WASTE The Case of Ferrous Scrap 28 June 2000 EUROFER and EFR 1 Contents: A description of the three scrap cycles that cover

More information

Materials & Processes in Manufacturing

Materials & Processes in Manufacturing Materials & Processes in Manufacturing ME 151 Chapter 18 Hot Working Processes 1 Introduction Forming of materials their recrystallization temperature Higher temperatures weaken the metal making it more

More information

Continuous Cast Iron. Your foremost provider of specialty products, services and solutions

Continuous Cast Iron. Your foremost provider of specialty products, services and solutions Continuous Cast Iron Your foremost provider of specialty products, services and solutions Quik Guide Continous Cast Iron Quik Guide TYPE DURA-BAR MACHINABILITY GRADE RATING 1 TYPICAL APPLICATIONS G1 125%

More information

Numerous road and bridge construction pay items are measured by weight -- usually tons or pounds.

Numerous road and bridge construction pay items are measured by weight -- usually tons or pounds. INTRODUCTION TO WEIGHT MEASUREMENTS Numerous road and bridge construction pay items are measured by weight -- usually tons or pounds. METHODS Several different techniques can be employed for weight measurement.

More information

SECTION 410 FENCES All materials shall be new and without flaws or defects of any type GENERAL

SECTION 410 FENCES All materials shall be new and without flaws or defects of any type GENERAL SECTION 410 FENCES 410.1 GENERAL This work shall consist of the construction of fences and gates in substantial compliance with the specifications, lines, and grades shown on the plans or established by

More information

Iron & Steel Scrap Specifications Manual

Iron & Steel Scrap Specifications Manual Iron & Steel Scrap Specifications Manual TABLE OF CONTENTS INTRODUCTION... 3 GENERAL TERMS AND CONDITIONS... 4 GENERAL IRON & STEEL SPECIFICATIONS... 9 SAFETY AND ENVIRONMENTAL POLICIES... 10 CLOSED CONTAINERS/SEALED

More information

B - Deck Steel Roll Forming Machine

B - Deck Steel Roll Forming Machine B - Deck Steel Roll Forming Machine R O L L F O R M E R S U S A I W W W. R O L L F O R M E R S - U S A. C O M Page1 Cantilevered Dual Headed 15,000 lb. Decoiler 15,000 lb. Capacity Decoiler Includes mandrell

More information

50 lbs (23 kg) of + #8 (+2.36 mm) material plus 50 lbs (23 kg) of pile run material.

50 lbs (23 kg) of + #8 (+2.36 mm) material plus 50 lbs (23 kg) of pile run material. 5.5 REQUIRED SAMPLE SIZES 1. SCOPE This section covers the size of samples to be submitted to the s and Research Center for testing. The sample sizes listed are minimums and in special cases the Engineer

More information

ITEM 555 CHAIN LINK FENCING

ITEM 555 CHAIN LINK FENCING ITEM 555 AFTER MARCH 1, 2012 CHAIN LINK FENCING 555.1 Description. This item shall govern for furnishing the quantities of chain link fencing and gates as shown on the plans, including all posts, bracing

More information

ALUMINIUM AND ARTICLES THEREOF

ALUMINIUM AND ARTICLES THEREOF CHAPTER 76 ALUMINIUM AND ARTICLES THEREOF Note 1. In this chapter, the following expressions have the meanings hereby assigned to them: (a) Bars and rods: Rolled, extruded, drawn or forged products, not

More information

Resource Guide. Section 3: Ductile Iron

Resource Guide. Section 3: Ductile Iron Resource Guide Section 3: Ductile Iron Section 3 Ductile Iron Description of Grades... 3-3 65-45-12 Ferritic... 3-4 80-55-06 Partially Pearlitic... 3-6 100-70-02 Pearlitic... 3-8 4512 HRDS Heat Resistant...

More information

CONCRETE STEPS, HANDRAILS, AND SAFETY RAIL

CONCRETE STEPS, HANDRAILS, AND SAFETY RAIL CONCRETE STEPS, HANDRAILS, AND SAFETY RAIL PART 1 - GENERAL 1.01 SECTION INCLUDES A. Concrete Steps B. Handrails C. Safety Rail 1.02 DESCRIPTION OF WORK A. Construction of concrete steps. B. Furnishing

More information

Can Process Scrap Specification

Can Process Scrap Specification Rev 3 February 2018 Can Process Scrap Specification Document Manager: Kerry Ward Approved by: Michael Anderson Note: This is considered an uncontrolled document unless it is being viewed on-line from the

More information

Water Utility Science Water Math and Hydraulics 050. Name: Date:

Water Utility Science Water Math and Hydraulics 050. Name: Date: Water Utility Science Water Math and Hydraulics 050 Name: Date: Note: Please show all of your calculations for each problem no matter how simple the problem may seem. Please use the accompanying pieces

More information

MANUFACTURING PROCESSES

MANUFACTURING PROCESSES 1 MANUFACTURING PROCESSES - AMEM 201 Lecture 8: Forming Processes (Rolling, Extrusion, Forging, Drawing) DR. SOTIRIS L. OMIROU Forming Processes - Definition & Types - Forming processes are those in which

More information

For each ton of molten pig iron, you need: 2600 lbs iron ore or iron ore pellets, 1000 lbs coke 300 lbs of flux (slag, dolomite, limestone, etc).

For each ton of molten pig iron, you need: 2600 lbs iron ore or iron ore pellets, 1000 lbs coke 300 lbs of flux (slag, dolomite, limestone, etc). Steel Mills Steel Process Flow For each ton of molten pig iron, you need: 2600 lbs iron ore or iron ore pellets, 1000 lbs coke 300 lbs of flux (slag, dolomite, limestone, etc). Steel Mill - Raw Materials

More information

Steel Haseeb Ullah Khan Jatoi Department of Chemical Engineering UET Lahore

Steel Haseeb Ullah Khan Jatoi Department of Chemical Engineering UET Lahore Steel Haseeb Ullah Khan Jatoi Department of Chemical Engineering UET Lahore Recap Eutectic phase diagram Eutectic phase diagram Eutectic isotherm Invariant point Eutectic Reaction Compositions of components

More information

Resource Guide. Section 2: Gray Iron

Resource Guide. Section 2: Gray Iron Resource Guide Section 2: Gray Iron Section 2 Gray Iron Description of Grades... 2-3 G1 Partially Ferritic... 2-4 G1A Ferritic... 2-6 G2 Highly Pearlitic... 2-8 G2A Highly Perlitic High-Strength... 2-10

More information

Engineering Materials

Engineering Materials Engineering Materials Lecture 2 MEL120: Manufacturing Practices 1 Selection of Material A particular material is selected is on the basis of following considerations 1. Properties of material 1. Properties

More information

S P E C I A L S T E E L S

S P E C I A L S T E E L S S P E C I A L S T E E L S Index Free Cutting Steel 2M07 ( ENA) Page 2 Bright Mild Steel 070M ( ENA) Page 4 Carbon Axle Steel 0M ( EN8) Page 6 Carbon Steel 070M ( EN9) Page 8 % Chromium Molybdenum Steel

More information

Ore-Based Metallics: adding value to the EAF SEASI CONFERENCE & EXHIBITION. MAY 2017

Ore-Based Metallics: adding value to the EAF SEASI CONFERENCE & EXHIBITION. MAY 2017 Ore-Based Metallics: adding value to the EAF SEASI CONFERENCE & EXHIBITION. MAY 2017 Disclaimer This presentation is intended for information purposes only and is not intended as commercial material in

More information

Adam J Gesing Gesing Consultants Inc Lightweighting Summit 19-21May 2014, Detroit, MI

Adam J Gesing Gesing Consultants Inc Lightweighting Summit 19-21May 2014, Detroit, MI Adam J G G C Lightweighting Summit 19-21May 2014, Detroit, MI Current state of light-metal recycling from both production facilities and post consumer scrap Use of scrap alloy batching for vehicle production

More information

Lecture 13 End of Life Vehicles

Lecture 13 End of Life Vehicles Lecture 13 End of Life Vehicles Introduction 2/25 An end-of-life vehicle is a car or a light commercial vehicle (carry max. 3.5 tons) which is to be disposed of by the registered owner. Sources of ELVs

More information

J.I.C. HYDRAULIC TUBING Seamless & Welded Hydraulic Fluid Line 23 Seamless Burst Pressures & Working Pressures 24 Welded Burst Pressures 25

J.I.C. HYDRAULIC TUBING Seamless & Welded Hydraulic Fluid Line 23 Seamless Burst Pressures & Working Pressures 24 Welded Burst Pressures 25 TABLE OF CONTENTS STEEL & ALLOY ROUND MECHANICAL TUBING Drawn Over Mandrel (DOM) 3-15 Cold Drawn Seamless (CDS) 3-15 Hot Rolled Seamless (HRS) 3-15 Electric Resistance Welded (ERW) 3-15 Seamless 4130/4140

More information

The Convenience Stores For Metal

The Convenience Stores For Metal STEEL Data and Specifications 303 Chromium-nickel stainless steel with added sulfur or selenium and phosphorus to improve machinability and non-seizing properties. It is the most free machining of the

More information

CW 3550 Chain Link and Drift Control Fence TABLE OF CONTENTS

CW 3550 Chain Link and Drift Control Fence TABLE OF CONTENTS January 2014 SPECIFICATION CW 3550 R3 CW 3550 Chain Link and Drift Control Fence TABLE OF CONTENTS 1. GENERAL CONDITIONS... 1 3. DESCRIPTION... 1 5. MATERIALS... 1 5.1 Drift Control Fence... 1 5.1.1 Approved

More information

Appendix 13A Calibrating Manure Spreaders

Appendix 13A Calibrating Manure Spreaders 651.1350 Appendix 13A Calibrating Manure Spreaders (210-vi-AWMFH, May 1996) 13A 9 13A 10 (210-vi-AWMFH, May 1996) Appendix 13A Calibrating Manure Agricultural Spreading Waste Management The use of animal

More information

FACTFILE: GCE TECHNOLOGY & DESIGN

FACTFILE: GCE TECHNOLOGY & DESIGN FACTFILE: GCE TECHNOLOGY & DESIGN 1.3 METAL PART 1 Metal Part 1 Learning outcomes Students should be able to: Demonstrate knowledge of the available form of supply of metals; Understand the difference

More information

Automated Cantilevered Aluminum Sliding Gate

Automated Cantilevered Aluminum Sliding Gate Town of Derry, New Hampshire REQUEST FOR PROPOSALS B18-128 January 25, 2018 The Town of Derry - Department of Public Works is seeking proposals for: Automated Cantilevered Aluminum Sliding Gate Introduction

More information

SECTION 1043 FENCE MATERIAL

SECTION 1043 FENCE MATERIAL SECTION 1043 FENCE MATERIAL 1043.1 Scope. This specification covers the material required in the construction of chainlink fence and woven wire fence. 1043.2 Basis of Acceptance. The basis of acceptance

More information

SECTION V HANDLING & TRANSFER CHARGES GENERALLY APPLICABLE TO CARGO <<< BACK TO TARIFF INDEX

SECTION V HANDLING & TRANSFER CHARGES GENERALLY APPLICABLE TO CARGO <<< BACK TO TARIFF INDEX SECTION V HANDLING & TRANSFER CHARGES GENERALLY APPLICABLE TO CARGO Charges published in this section are subject to all rules, regulations and provisions published in other sections of this tariff, and

More information

CONCRETE STEPS, HANDRAILS, AND SAFETY RAIL

CONCRETE STEPS, HANDRAILS, AND SAFETY RAIL SUDAS Standard Specifications Division 9 - Site Work and Landscaping Section 9080 - Concrete Steps, Handrails, and Safety Rail CONCRETE STEPS, HANDRAILS, AND SAFETY RAIL PART - GENERAL.0 SECTION INCLUDES

More information

NATIONAL CERTIFICATE (VOCATIONAL) NQF LEVEL 3 NOVEMBER

NATIONAL CERTIFICATE (VOCATIONAL) NQF LEVEL 3 NOVEMBER MARKING GUIDELINE NATIONAL CERTIFICATE (VOCATIONAL) NQF LEVEL 3 NOVEMBER 2009 This memorandum consists of 5 pages. MARKING GUIDELINE -2- NC1520(E)(N3)/V QUESTION 1: GENERAL 1.1.1 True 1.1.2 True 1.1.3

More information

Structural Channels A-36:20-40 LG. Standard Beams

Structural Channels A-36:20-40 LG. Standard Beams Floor Plates #/Sq. Ft. 14 Ga. 3.75 12 Ga. 5.25 1/8 6.16 3/16 8.71 1/4 11.26 5/16 13.81 3/8 16.37 Plates #/Sq. Ft. 3/16 7.66 1/4 10.21 5/16 12.76 3/8 15.32 7/16 17.87 1/2 20.42 9/16 22.97 5/8 25.52 3/4

More information

BAUMANN SPRINGS Springs and Stampings for the World.

BAUMANN SPRINGS Springs and Stampings for the World. Welcome BAUMANN SPRINGS Springs and Stampings for the World. SPIRAL SPRINGS COMPRESSION SPRINGS WAVE SPRINGS ASSEMBLIES HUBCAP & RETAINING TENSION AND TORSION SPRINGS MICRO SPRINGS PRESSINGS AND STAMPINGS

More information

SPECIFICATIONS - DETAILED PROVISIONS Section Stainless Steel Sluice Gates C O N T E N T S

SPECIFICATIONS - DETAILED PROVISIONS Section Stainless Steel Sluice Gates C O N T E N T S SPECIFICATIONS - DETAILED PROVISIONS Section 11294 - Stainless Steel Sluice Gates C O N T E N T S PART 1 - GENERAL... 1 1.01 SUMMARY... 1 1.02 REFERENCES... 1 1.03 DEFINITIONS... 1 1.04 DESIGN REQUIREMENTS...

More information

METALWORKING DEFORMATION YOUR ADVANTAGE IN AN INDUSTRIAL WORLD

METALWORKING DEFORMATION YOUR ADVANTAGE IN AN INDUSTRIAL WORLD METALWORKING DEFORMATION YOUR ADVANTAGE IN AN INDUSTRIAL WORLD A CHOICE TO SUIT ALL NEEDS We offer you an innovative, comprehensive and high performing metal forming product range under the Castrol Iloform

More information

SECTION RADIO FREQUENCY SHIELDING ENCLOSURE RF Modular Pan System

SECTION RADIO FREQUENCY SHIELDING ENCLOSURE RF Modular Pan System SECTION 13096 RADIO FREQUENCY SHIELDING ENCLOSURE RF Modular Pan System Prepared by: 90 Dayton Avenue, Unit 4B, Suite 13 Passaic, NJ 07055 (973) 574-9077 13096-1 RF MODULAR PAN SYSTEM PART 1 GENERAL 1.1

More information

Dr. M. Sayuti, ST.,M.Sc JURUSAN TEKNIK INDUSTRI FAKULTAS TEKNIK UNIVERSITAS MALIKUSSALEH

Dr. M. Sayuti, ST.,M.Sc JURUSAN TEKNIK INDUSTRI FAKULTAS TEKNIK UNIVERSITAS MALIKUSSALEH POWDER METALLURGY Dr. M. Sayuti, ST.,M.Sc JURUSAN TEKNIK INDUSTRI FAKULTAS TEKNIK UNIVERSITAS MALIKUSSALEH 1- INTRODUCTION Powder metallurgy is the name given to the process by which fine powdered materials

More information

MERCHANTS METALS. A. ASTM F552 Standard Terminology Relating to Chain Link Fencing

MERCHANTS METALS. A. ASTM F552 Standard Terminology Relating to Chain Link Fencing MERCHANTS METALS SECTION 32 31 13 COLORBOND CHAIN LINK FENCE AND GATES 2014 PART 1 GENERAL 1.1 RELATED DOCUMENTS A. DIVISION 01 - GENERAL REQUIREMENTS: Drawings, quality, product and performance requirements,

More information

Mercury Contamination from Metal Scrap Processing Facilities A Study by Ohio EPA

Mercury Contamination from Metal Scrap Processing Facilities A Study by Ohio EPA Mercury Contamination from Metal Scrap Processing Facilities A Study by Ohio EPA Paper #: 947 Radhica Sastry Ohio Environmental Protection Agency Lazarus Government Center P.O. Box 1049 Columbus, OH-43216

More information

Powder-Metal Processing and Equipment

Powder-Metal Processing and Equipment Powder-Metal Processing and Equipment Text Reference: Manufacturing Engineering and Technology, Kalpakjian & Schmid, 6/e, 2010 Chapter 17 Powder Metallurgy Metal powders are compacted into desired and

More information

Manufacturing Process - I

Manufacturing Process - I Manufacturing Process - I UNIT II Metal Forming Processes Prepared By Prof. Shinde Vishal Vasant Assistant Professor Dept. of Mechanical Engg. NDMVP S Karmaveer Baburao Thakare College of Engg. Nashik

More information

Powder Metallurgy. Powder-Metal Processing and Equipment 11/10/2009

Powder Metallurgy. Powder-Metal Processing and Equipment 11/10/2009 Powder Metallurgy Powder-Metal Processing and Equipment Metal powders are compacted into desired and often complex shapes and sintered* to form a solid piece * Sinter: To heat without melting Text Reference:

More information

N OTHING IS M ORE IM PORTA NT THA N THE ENVIRONM ENT A ROUND US. WE A RE A LL A WA RE OF THE DA NGERS OF EX HA USTING OUR NA TURA L

N OTHING IS M ORE IM PORTA NT THA N THE ENVIRONM ENT A ROUND US. WE A RE A LL A WA RE OF THE DA NGERS OF EX HA USTING OUR NA TURA L Pyral AG N OTHING IS M ORE IM PORTA NT THA N THE ENVIRONM ENT A ROUND US. WE A RE A LL A WA RE OF THE DA NGERS OF EX HA USTING OUR NA TURA L RESOURCES A ND THE CONTINUED THREA T THA T THE RELEA SE OF C02

More information

Brown University Revised August 3, 2012 Facilities Design & Construction Standards SECTION HVAC PIPES AND TUBES

Brown University Revised August 3, 2012 Facilities Design & Construction Standards SECTION HVAC PIPES AND TUBES SECTION 23 20 00 - HVAC PIPES AND TUBES PART 1 - GENERAL 1.1 SUMMARY: A. Section includes pipe and pipe fittings for: heating water, chilled water, steam and steam condensate, condenser water, glycol,

More information

SECTION ALUMINUM GATES

SECTION ALUMINUM GATES P.O. Box 1058 370 South Athol Rd. Athol, Massachusetts 01331 Phone: (978) 249-7924 Fax: (978) 249-3072 SECTION ALUMINUM GATES PART 1 GENERAL 1.01 SCOPE OF WORK A. The CONTRACTOR shall furnish all labor,

More information

English BRIQUETTING BALING BREAKING CUTTING SHREDDING SORTING HIGH PERFORMANCE - METAL RECYCLING

English BRIQUETTING BALING BREAKING CUTTING SHREDDING SORTING HIGH PERFORMANCE - METAL RECYCLING English BRIQUETTING BALING BREAKING CUTTING SHREDDING SORTING HIGH PERFORMANCE - METAL RECYCLING Metal Recycling is not just Metal Recycling It is a well-known fact: metal recyc-ling is not just metal

More information

This procedure applies to the operations of two 5000 lb. capacity furnaces with one 1250 kw variable frequency power unit to melt steel.

This procedure applies to the operations of two 5000 lb. capacity furnaces with one 1250 kw variable frequency power unit to melt steel. PAGE: 1 of 10 1.0 SCOPE This procedure applies to the operations of two 5000 lb. capacity furnaces with one 1250 kw variable frequency power unit to melt steel. 2.0 RESPONSIBILITY The melter is responsible

More information

SECTION CHAIN LINK FENCES AND GATES

SECTION CHAIN LINK FENCES AND GATES SECTION 32 31 13 SPEC WRITER NOTES: Use this section only for NCA projects. Delete text between // // not applicable to project. Edit remaining text to suit project. PART 1 - GENERAL 1.1 SUMMARY A. Section

More information

MATERIAL ALLOWANCES AND UNIT PRICES

MATERIAL ALLOWANCES AND UNIT PRICES PART 1 - GENERAL 1.1 SECTION INCLUDES ADDITIONS AND RENOVATIONS TO WEST YORK AREA HIGH SCHOOL - #1231 SECTION 012200 MATERIAL ALLOWANCES AND UNIT PRICES A. Measurement and payment criteria applicable to

More information

Ontario ENGINEERING STANDARD GUIDELINE 1.0 PURPOSE 2.0 THERMITE WELDING 2.1 WELD PROCEDURE

Ontario ENGINEERING STANDARD GUIDELINE 1.0 PURPOSE 2.0 THERMITE WELDING 2.1 WELD PROCEDURE /7.0 PURPOSE The following guideline addresses the minimum requirements to successfully thermite weld. This is not meant to supersede the thermite kit manufacturer s procedure / methodology. 2.0 THERMITE

More information

SECTION CHAIN LINK FENCING

SECTION CHAIN LINK FENCING SECTION 02835 - CHAIN LINK FENCING 1.0 GENERAL 1.1 Furnish and install chain link fencing complete in place with gates and accessories as specified herein and as shown on the Contract Drawings. 1.2 Reference

More information

Product categories NEWCAST Page 1 of 5

Product categories NEWCAST Page 1 of 5 Page 1 of 5 1.0 1 Ferrous castings Iron, steel and malleable foundries 1.1 Material groups 1.1.1 Grey cast iron 1.1.2 Spheroidal graphite cast iron 1.1.3 Compacted graphite cast iron 1.1.4 Malleable cast

More information

MASS PER CUBIC FOOT (METER), YIELD, AND AIR CONTENT (GRAVIMETRIC) OF FRESHLY MIXED CONCRETE (Kansas Test Method KT-20)

MASS PER CUBIC FOOT (METER), YIELD, AND AIR CONTENT (GRAVIMETRIC) OF FRESHLY MIXED CONCRETE (Kansas Test Method KT-20) 5.9.20 MASS PER CUBIC FOOT (METER), YIELD, AND AIR CONTENT (GRAVIMETRIC) OF FRESHLY MIXED CONCRETE (Kansas Test Method ) 1. SCOPE This method of test covers the procedure for determining the mass per cubic

More information

KNIVES. giving you the EDGE, to stay AHEAD. TUBE & METAL FORMING

KNIVES. giving you the EDGE, to stay AHEAD. TUBE & METAL FORMING KNIVES giving you the EDGE, to stay AHEAD. TUBE & METAL FORMING ATLAS has comprehensive in-house designing facility to design new products according to customer s specific requirements with complete satisfaction

More information

Presentation on Chip Compactor

Presentation on Chip Compactor Yuken India Limited A Group Company of Yuken Kogyo Co. Limited, Japan Presentation on Chip Compactor H.S.Praveen Kumar, AGM, Machine Tool Division Comprehensive Hydraulic Solutions CONTENTS YUKEN INDIA

More information

NRDCA 300 PROCEDURES TO DETERMINE THE ACCURACY OF MATERIAL MEASURING EQUIPMENT FOR LIGHTWEIGHT INSULATING CONCRETE

NRDCA 300 PROCEDURES TO DETERMINE THE ACCURACY OF MATERIAL MEASURING EQUIPMENT FOR LIGHTWEIGHT INSULATING CONCRETE NRDCA 300 PROCEDURES TO DETERMINE THE ACCURACY OF MATERIAL MEASURING EQUIPMENT FOR LIGHTWEIGHT INSULATING CONCRETE I. Scope Lightweight insulating concrete is field produced with specialized mixing equipment.

More information

张家港市张运机械制造有限公司 Zhangjiagang City Zhangyun Machinery Manufacturing Co.,Ltd. ZY76 (Enlarged to 114) HF Welded Pipe Mill Solution

张家港市张运机械制造有限公司 Zhangjiagang City Zhangyun Machinery Manufacturing Co.,Ltd. ZY76 (Enlarged to 114) HF Welded Pipe Mill Solution ZY76 (Enlarged to 114) HF Welded Pipe Mill Solution (Φ25.4~Φ114mm x 1.2~4.0mm x 4~10m x 30~80 m/min) To: Zehtabchiyan From: 1 / 11 I Summary 张家港市张运机械制造有限公司 This high-frequency welding pipe mill is specialized

More information

DIVISION 5 - STRUCTURAL STEEL AND IRON WORK

DIVISION 5 - STRUCTURAL STEEL AND IRON WORK DIVISION 5 - STRUCTURAL STEEL AND IRON WORK SECTION 05100 STRUCTURAL METAL FRAMING PART 1.00 GENERAL 1.01 SCOPE OF WORK A. Work Included: 1. 2. Structural steel complete in place. Steel joists complete

More information

CARBON STEEL BARS HOT ROLLED

CARBON STEEL BARS HOT ROLLED CARBON STEEL BARS HOT ROLLED Grade Description...3-2 Rounds...3-3 thru 3-4 Strip...3-5 Flats (A-36)...3-6 thru 3-8 (M1044)...3-9 Squares...3-9 Reinforcing Bars...3-10 Reinforcing Mesh...3-10 TOLERANCES...3-11

More information

Conveyor systems. Reliability and experience based on tradition. Hinged belt conveyors Scraper conveyors Belt conveyors

Conveyor systems. Reliability and experience based on tradition. Hinged belt conveyors Scraper conveyors Belt conveyors Conveyor systems. Reliability and experience based on tradition. Page Hinged belt conveyors..................... 10 Scraper conveyors........................ 16 Belt conveyors...........................

More information

In conjunction with MJAC Midland Joint Advisory Council for Environmental Protection. Present. Advanced Module IV

In conjunction with MJAC Midland Joint Advisory Council for Environmental Protection. Present. Advanced Module IV In conjunction with MJAC Midland Joint Advisory Council for Environmental Protection Established 1928 Present Advanced Seminar IV Taking Legal Action Advanced Module IV Session 2 Introduction to Ferrous

More information

Manufacture of Iron & Steel. Prepared By: John Cawley

Manufacture of Iron & Steel. Prepared By: John Cawley Manufacture of Iron & Steel Prepared By: John Cawley Presentation Objectives Identify the basic steps in the production of steel. Identify the properties and uses of iron ore and pig iron. Differentiate

More information

Aluminum Siding - includes aluminum siding (free of insulation), downspouts, gutters, trimming, and empty wire conduit.

Aluminum Siding - includes aluminum siding (free of insulation), downspouts, gutters, trimming, and empty wire conduit. *The following information is only to be used as a guide. Final decision of material type will be made by qualified Berks Container Recovery employees. If you have a material that you would like to recycle

More information

Aluminum Siding - includes aluminum siding (free of insulation), downspouts, gutters, trimming, and empty wire conduit.

Aluminum Siding - includes aluminum siding (free of insulation), downspouts, gutters, trimming, and empty wire conduit. *The following information is only to be used as a guide. Final decision of material type will be made by qualified Berks Container Recovery employees. If you have a material that you would like to recycle

More information

Manure Spreader Calibration. Jerry Martin, Senior Extension Associate, Penn State Crop & Soil Sciences

Manure Spreader Calibration. Jerry Martin, Senior Extension Associate, Penn State Crop & Soil Sciences Manure Spreader Calibration Jerry Martin, Senior Extension Associate, Penn State Crop & Soil Sciences 717-394-6851 jmartin@psu.edu Nutrient Management Planning Goals of nutrient management Maximize i profitable

More information

Testing. Test drainage products according to the applicable AASHTO or ASTM specification, except as otherwise noted.

Testing. Test drainage products according to the applicable AASHTO or ASTM specification, except as otherwise noted. 909.01 Section 909. DRAINAGE PRODUCTS 909.01 General Requirements. If only the size and class are specified for a culvert or sewer, use the pipe materials as shown in Table 401-1 and 402-1 respectively.

More information

Attachment A-Flagpole(s) Specifications

Attachment A-Flagpole(s) Specifications Attachment A-Flagpole(s) Specifications PART 1-GENERAL 1.1 SCOPE A. The scope of work includes the removal of existing flagpole(s) and associated concrete bases, and installation of a new flagpole(s) and

More information

MANUFACTURING TECHNOLOGY

MANUFACTURING TECHNOLOGY MANUFACTURING TECHNOLOGY UNIT II Hot & Cold Working Forging & Rolling Mechanical Working of Metals In this method no machining process is carried out, but it is used to achieve optimum mechanical properties

More information

VPL-3300B Commercial Vertical Platform Lift Technical Specifications

VPL-3300B Commercial Vertical Platform Lift Technical Specifications Page 1 of 5 VPL-3300B Commercial Vertical Platform Lift Technical Specifications MODEL NUMBERS: Unenclosed VPL-3300B Series: Models VPL-3353B and VPL-3375B (DC-powered) 3-Gate VPL-3300B Series: Models

More information

Aircraft. Automotive. Electronic. Oil and Gas

Aircraft. Automotive. Electronic. Oil and Gas 4. Industry Applications of Copper Aircraft Heat Exchange Cable Assembly Terminals Couplers and Connectors Valves Automotive Radiators Brake Tubing Brake Lines Air Coolers Tubing for Master Cylinder Electronic

More information

CHAIN LINK FENCES AND GATES

CHAIN LINK FENCES AND GATES SECTION 02831 CHAIN LINK FENCES AND GATES PART 1 GENERAL 1.01 SUMMARY A. Alternate Material for Fence Post and Framing Material: Where schedule 40 galvanized steel is specified, the following will be accepted:

More information

Steel and Raw Materials Data Price Feed

Steel and Raw Materials Data Price Feed Steel and Raw Materials Data Price Feed Latin America export billet $ per tonne fob main port Latin America export slab $ per tonne fob main port UK domestic stainless steel scrap 12-13% Cr Solids per

More information

OVERSHOT GATE TECHNICAL DATA SHEET

OVERSHOT GATE TECHNICAL DATA SHEET FRESNO OVERSHOT GATE TECHNICAL DATA SHEET Applications Fresno Overshot Gates effectively control upstream and downstream levels of canals. Improved flow control is achieved through the use of this fully

More information

Specification. Non-Ferrous.

Specification. Non-Ferrous. Specification. Non-Ferrous. 2 In the Recycling Business since 1888. RIMECO is a 5th generation, family owned company with a solid history of innovation and expertise. As a reliable and flexible partner,

More information

Bulk Deformation Processes

Bulk Deformation Processes Bulk Deformation Processes Bachelor of Industrial Technology Management with Honours Semester I Session 2013/2014 TOPIC OUTLINE What is Bulk Deformation? Classification of Bulk Deformation Processes Types

More information

CITY OF FRIENDSWOOD TECHNICAL SPECIFICATIONS DOCUMENT 00085B ADDENDUM ADDENDUM NO. 1

CITY OF FRIENDSWOOD TECHNICAL SPECIFICATIONS DOCUMENT 00085B ADDENDUM ADDENDUM NO. 1 ADDENDUM Date of Addendum: December 30 th, 2015 PROJECT NAME: Fencing for Sportspark PROJECT NO: GO1507 BID DATE: Tuesday, January 5 th, 2016 FROM: City of Friendswood Department of Public Works 1306 Deepwood

More information

Raychem S1297 and /97 Hot Melt Adhesive

Raychem S1297 and /97 Hot Melt Adhesive Tyco Electronics Corporation 300 Constitution Drive Menlo Park, CA 94025 USA Specification This Issue: Date: Replaces: RW-2019 ISSUE 1 November 16, 2005 None Raychem S1297 and /97 Hot Melt Adhesive 1.0

More information

K-FLEX SOLAR SYSTEM SOLAR SYSTEM

K-FLEX SOLAR SYSTEM SOLAR SYSTEM K-FLEX SOLAR SYSTEM SOLAR SYSTEM K-FLEX offers a line of products designed specifically for solar heating, renewable energy sources used to produce hot water using solar energy. The product range consists

More information

Concrete Field Testing Technician Study Guide

Concrete Field Testing Technician Study Guide Concrete Field Testing Technician Study Guide ASTM C 172 SAMPLING FRESH CONCRETE 1. The maximum allowable time between obtaining the first and final portions of a composite sample is minutes. (Section

More information

General Claims Policy

General Claims Policy INTRODUCTION This general claims policy covers light flat rolled sheet and tin mill products produced at all ArcelorMittal USA flat rolled facilities. It covers the major points of a claim policy, but

More information

The Convenience Stores For Metal

The Convenience Stores For Metal STEEL BARS Data and Specifications C1018 Cold Finished Bar A low carbon steel with medium manganese content. Applications: Cold forming and bending operations (for severe bends stress relieving may be

More information

SECTION METAL STAIRS

SECTION METAL STAIRS SECTION 05 51 00 METAL STAIRS PART 1 GENERAL 1.1 SUMMARY A. Section includes steel stair frame of structural sections, with closed risers; pan to receive concrete fill stair treads and landings; integral

More information