DRUM PUMP CHEMICAL RESISTANCE GUIDE AND APPLICATION WORKSHEET

Transcription

1 DUM PUMP CHEMICAL ESISTANCE GUIDE AND APPLICATION WOKSHEET TECHNICAL BULLETIN TPS The information contained in this Drum Pump Chemical esistance Guide is to be used only as a general guide for proper drum pump tube selection. No warranty is implied nor is any guarantee provided. When compatibility data are inconclusive, field testing is recommended. An asterisk indicates the material is flammable and may only be handled with a stainless steel pump tube and appropriate drive motor which are properly grounded and bonded according to Operating Instructions. Alway sconsult with a safety engineer for proper drive motor selection when pumping flammables. All test data listed is at room temperature (72 F, 22 C) unless otherwise stated. = ecommended M = Minor to moderate, should be field tested = Not recommended = No data = Flammable or explosive any explosion-proof motor as well as the container when transferring explosive material. Always consult with a Safety Engineer for proper pump / motor selection. PVDF (KYNA ) - MA. 175 F (80 C) POLYPOPYLENE - MA. 130 F (54 C) PVDF (KYNA ) - MA. 175 F (80 C) POLYPOPYLENE - MA. 130 F (54 C) Acetaldehyde Ammonium persulfate Acetamide (PVDF, to 75 F/24 C) Ammonium phosphate, dibasic Acetate solvents Ammonium phosphate, monobasic Acetic acid (10% -80%) M Ammonium phosphate, tribasic Acetic acid (80%) M Ammonium sulfate Acetic acid, glacial (PVDF, to 120 F/49 C) M (PP, to 100 F/38 C) Acetic anhydride Acetone Acetyl chloride M Amyl acetate Acetylene Amyl chloride Alcohols Aniline (PVDF, to 75 F/24 C) M Aluminum chloride Aniline dyes M Aluminum fluoride Aniline hydrochloride (PVDF, to 75 F/24 C) Aluminum hydroxide Anisole Aluminum nitrate Aqua regia (80%) (PVDF, to 75 F/24 C) Aluminum potassium sulfate Arsenic acid Aluminum sulfate Barium carbonate Amines Barium chloride M Ammonia, aqua (10%) Barium hydroxide Ammonia, aqueous Barium nitrate Ammonia, (concentrated) Barium sulfate Ammonium bifluoride (PP, to 70 F/21 C) Barium sulfide Ammonium carbonate Benzaldehyde (PVDF, to 75 F/24 C) Ammonium chloride M Benzene, benzol Ammonium fluoride (10%) Ammonium fluoride (25%) Ammonium hydroxide Ammonium nitrate Ammonium nitrite (PP, to 70 F/21 C) Ammonium oxalate Ammonium sulfide (PVDF & CPVC / PVDF, to 125 F/52 C) Ammonium thiocyanate Ammonium thiosulfate Benzene sulfonic acid (PVDF, to 75 F/24 C) M Benzoic acid M Bismuth carbonate Black liquors Boric acid Brine acid

2 Page 2 DUM PUMP Chemical esistance Guide (cont d.) = ecommended M = Minor to moderate, should be field tested = Not recommended = No data = Flammable or explosive any explosion-proof motor as well as the container when transferring explosive material. Always consult with a Safety Engineer for proper pump / motor selection. PVDF (KYNA ) - MA. 175 F (80 C) POLYPOPYLENE - MA. 130 F (54 C) PVDF (KYNA ) - MA. 175 F (80 C) POLYPOPYLENE - MA. 130 F (54 C) Bromic acid Bromine liquid (PVDF, to 150 F/66 C) Bromine water M Butane Butyl acetate M Butyl phenol Butylene Butyric acid Calcium bisulfide M Calcium bisulfite M Calcium chlorate Calcium chloride M Calcium hydroxide Calcium hypochlorite _ (PVDF & CPVC / PVDF, to 70 F/21 C) Calcium nitrate M Calcium sulfate Calcium sulfite M Carbon disulfide _ Carbonic acid Carbon tetrachloride Cellosolve M Cetyl alcohol Chlorine liquid Chloroacetic acid Chlorobenzene Chlorobenzyl chloride (PVDF, to 125 F/52 C) Chloroform (PVDF, to 125 F/52 C) Chlorosulfonic acid (100%) Chromic/sulfuric acid Chromic acid (10%) (PVDF& CPVC / PVDF, to 120 F/49 C) Chromic acid (50%) (PVDF, to 120 F/49 C) M (CPVC / PVDF, to 70 F/21 C) Citric acid Citric oils Copper chloride Copper cyanide Copper nitrate Copper sulfate Cresylic acid (PVDF, to 150 F/66 C) M Cyclohexane Cyclohexanol M Cyclohexanone M Diacetone alcohol Dichloroethylene Diesel fuels Diethyl ether M Diisobutylene M Dimethyl formamide Dioctyl phthalate Dyes Epichlorohydrine Ethanolamine Ether Ethyl acetate Ethyl chloride Ethyl ether Ethylene chloride Ethylene dichloride Ethylene glycol Ethylene oxide Fatty acids M M M Ferric chloride M Ferric nitrate Ferric sulfate Ferrous chloride Ferrous sulfate M Fluoboric acid (CPVC / PVDF, to 140 F/60 C) M Fluosilicic acid M M Formaldehyde (PVDF, to 120 F/49 C) Formic acid Furfural M Gallic acid (PVDF & CPVC / PVDF, to 75 F/24 C) M M Gelatin Glue P. V. A. M Glycerin Glycolic acid (PP, to 70 F/21 C) (PVDF & CPVC / PVDF, to 75 F/24 C) Glycols M

3 Page 3 DUM PUMP Chemical esistance Guide (cont d.) = ecommended M = Minor to moderate, should be field tested = Not recommended = No data = Flammable or explosive any explosion-proof motor as well as the container when transferring explosive material. Always consult with a Safety Engineer for proper pump / motor selection. PVDF (KYNA ) - MA. 175 F (80 C) POLYPOPYLENE - MA. 130 F (54 C) PVDF (KYNA ) - MA. 175 F (80 C) POLYPOPYLENE - MA. 130 F (54 C) Heptane Muriatic acid (37%) (hot) Hexane Naptha Hydrobromic acid M Napthalene M Hydrochloric acid (20%) Nickel chloride Hydrochloric acid (37%) (cold) Nickel sulfate Hydrochloric acid (37%) (hot) Nitric acid (5-10%) Hydrofluoric acid (20%) Nitric acid (20%) Hydrofluoric acid (50%) Nitric acid, (conc.) (PVDF, to 120 F/49 C) Hydrofluoric acid (75%) Nitric acid, red fuming Hydrofluoric acid (conc.) (cold) Nitrobenzene (PVDF, to 75 F/24 C) M M Hydrofluosilicic acid (20%) Oleic acid Hydrogen fluoride Oleum Hydrogen peroxide Oxalic acid (cold) (PVDF, to 125 F/52 C) Hydrogen sulfide (cold) Palmitic acid M Hydrogen sulfide (hot) Perchloric acid (PVDF, to 125 F/52 C) M Hypochlorous acid Perchloroethylene Iodine (PVDF, to 150 F/66 C) M M Petrolatum Isopropyl ether Phenol (carbolic acid) Jet fuel (JP3, JP4, JP5) Phosphoric acid (20%) M Lacquer solvents Phosphoric acid (20%-40%) Lactic acid (PVDF & CPVC / PVDF, to 120 F/49 C) Phosphoric acid (45%) M Lead acetate M Phosphorus, red Lead sulfamate Phosphorus, yellow Ligroin Photographic solutions Magnesium carbonate Plating solutions, chrome 40 Magnesium chloride Plating solutions, copper Magnesium hydroxide Plating solutions, gold Magnesium sulfate Plating solutions, iron Maleic acid M Plating solutions, lead Mercuric chloride (dilute solution) Plating solutions, nickel Mercuric cyanide Plating solutions, silver Methyl acetone Pl ating solutions, tin Methyl chloride Plating solutions, zinc Methyl ethyl ketone Potassium bicarbonate M Methyl isobutyl ketone Potassium bromide Methylene chloride Potassium carbonate Milk Potassium chlorate Monoethanolamine Potassium chloride Muriatic acid (20%) Potassium chromate M Muriatic acid (37%) (cold) Potassium dichromate

4 Page 4 DUM PUMP Chemical esistance Guide (cont d.) = ecommended M = Minor to moderate, should be field tested = Not recommended = No data = Flammable or explosive any explosion-proof motor as well as the container when transferring explosive material. Always consult with a Safety Engineer for proper pump / motor selection. PVDF (KYNA ) - MA. 175 F (80 C) POLYPOPYLENE - MA. 130 F (54 C) PVDF (KYNA ) - MA. 175 F (80 C) POLYPOPYLENE - MA. 130 F (54 C) Potassium hydroxide Sodium thiosulfate (PVDF & CPVC / PVDF, to 150 F/66 C) Stannic chloride Potassium nitrate Stearic acid Potassium permanganate M M Sulfate liquors Potassium sulfate M _ Sulfur Propionic acid (CPVC / PVDF, to 140 F/60 C) M Sulfur chloride (PVDF, to 75 F/24 C) Silicone oil Sulfur dioxide Silver nitrate Sulfuric acid (10%) M Soap solutions Sulfuric acid (10%-75%) M Sodium acetate Sulfuric acid (66 Baumè) M _ (PVDF & CPVC / PVDF, to 120 F/49 C) Sodium bicarbonate Sodium bisulfate Sulfurous acid M Sodium bisulfite Tannic acid Sodium borate M Tartaric acid Sodium bromide Tetrahydrofuran _ Tetralin Titanium tetrachloride (PVDF, to 150 F/66 C) M Sodium carbonate Sodium chlorate (50%) Sodium chloride Toluene (toluol) Sodium cyanide Transformer oil Sodium hydroxide (20%) Trichloroacetic acid _ (PVDF & CPVC/PVDF, to 75 F/24 C) Sodium hydroxide (50%) M Sodium hydroxide (80%) 1, 1, 1, Trichloroethane Sodium hypochlorite to 20% Trichloroethylene Sodium metaphosphate Tricresylphosphate Sodium nitrate Triethylamine (PVDF, to 125 F/52 C) _ Vinyl chloride Wood oil Sodium perborate Sodium phosphate M Sodium silicate Sodium sulfate Sodium sulfide ylene (xylol) Zinc hydrosulfite

5 Page 5 DUM PUMP Chemical esistance Guide (cont d.) TECHNICAL DATA Standard Formulas PESSUE AND HEAD Pressure (lbs. per sq. in) = Head in feet x Specific Gravity 2.31 = Head in feet x Specific Gravity x.434 Head in feet = TEMPEATUE (1.8 x C) + 32 = F.555 ( F 32) = C Degrees Kelvin VELOCITY Pipe Velocity (ft. / sec.) = lbs. per square inch x 2.31 Specific Gravity = Degrees Centigrade.408 x GPM (pipe diameter) 2 Velocity Head (feet) = (pipe velocity ft./sec.) x GPM pipe area CONVESION TABLE PESSUE IN POUNDS PE SQUAE INCH TO FEET OF HEAD Pounds Pressure Ft. of Head Pounds Pressure Ft. of Head CONVESION FACTOS FLOW Lbs of Water / Hr x.002 = Gal Min Gal / Min x 500 = Lbs of Water / Hr Lbs of Fluid / Hr Specific Gravity x.002 = Gal Min Liters / Min x.264 = Gal / Min (US) GPM x = Liters / Min Cu Meters / Hr x 4.4 = Gal / Min (US) Gal / Min x.227 = Cu Meters / Hr Kg of Water / Min x.264 = Gal / Min (US) Gal / MIn x 3.8 = Kg of Water / Min PESSUE Ft of Water x.433 = PSI PSI x 2.31 = Ft of Water Inches Hg x.491 = PSI Inches Hg x = Ft of Water ATM x 14.7 = PSI ATM x 33.9 = Ft of Water Kg / Sq cm x = PSI Meters of Water x 1.42 = PSI ATM x 760 = mm Hg mm Hg x.039 = Inches Hg Bar x 14.5 = PSI Newton / Meter 2 x 1 = Pascal PSI x 6.9 = kpa (Kilopascal) kpa x.145 = PSI VOLUME Lbs of Water x.119 = Gal Gal (Brit) x 1.2 = Gal (US) Gal x 128 = Fluid Ounces Cubic Ft x 7.48 = Gal Cubic In x = Gal Gal x = Liters Liter x.264 = Gal Cubic Meters x = Gallons Cubic Meter x 1000 = Liter Liters x 1000 = Cubic Centimeters Cubic Centimeters x.0338 = Fluid Ounces Fluic Ounces x = Cubic Centimeters LENGTH Mils x.001 = Inches Meters x = Feet Centimeters x.394 = Inches Millimeters x.0394 = Inches Microns x = Inches MASS Gal of Water x = Lbs Cubic Ft of Water x 62.4 = Lbs Ounces x.0625 = Lbs Kilograms x 2.2 = Lbs Lbs x.454 = Kilo Metric Ton x 2205 = Lbs METIC PEFIES Mega = 1,000,000 Kilo = 1,000 Hecto = 100 Deca = 10 Deci =.1 Centi =.01 Milli =.001 Micro = 000,001

6 Page 6 APPLICATIONS WOKSHEET APPLICATION INFO What type of application is this? Sanitary Industrial What type of fluid is the customer pumping? What is the viscosity of liquid being pumped (in centipoises)? cps Are there any solids present? NO YES - If so, what size? Total Dynamic Head: Vertical Feet Horizontal Feet CONTAINE INFO Elbows? NO YES - If so, how many? Valves? NO YES - If so, how many? Flow Meters? NO YES - If so, how many? What type of container is the customer pumping out of? 55 Gallon Drum Tote Tank Other Does the container have a hygienic bag liner? (Sanitary applications only) YES NO PUMP INFO Desired Flow ate? GPM (Gallons Per Minute) Type of motor required? Air Electric-115V Electric-230V Explosion Proof Type of motor enclosure? (Electric motors only) Open Drip Proof TEFC Note: Information subject to change without notice. egistered trademarks: Cellosolve - Union Carbide; Freon - DuPont; Kynar - Atochem ; Hastelloy - Haynes, Int l University Drive Phone: Auburn, Georgia USA FA: info@standardpump.com