ASTM, SAE AND ISO GRADE MARKINGS AND MECHANICAL PROPERTIES FOR STEEL FASTENERS
|
|
- Reynard Montgomery
- 6 years ago
- Views:
Transcription
1 ASTM, SAE AND ISO GRADE MARKINGS AND MECHANICAL PROPERTIES FOR STEEL FASTENERS Nominal Mechanical Properties Identification Grade Specification Fastener Description Material Size Range (in.) Proof Load (psi) Yield Strength Min (psi) Tensile Strength Min (psi) No Grade Grade 1 ASTM A307 Grades A&B Grade 2 Low or Medium Low Carbon Steel Low or Medium 33,000 36, /4 Over 55,000 57,000 3/4 to 33,000 36,000 60,000 60,000 No Grade Grade 4 Cold Drawn Steel B5 B6 Grade B5 Grade B6 AISI 501 1/4 Thru 4 AISI ,000 B7 B16 Grade B7 Grade B16 AISI 4140, 4142, OR 4105 CrMoVa Alloy Steel 2-1/2 Over 2-1/2 thru 4 Over 4 thru 7 75,000 Grade B8 AISI 304 1/4 and larger 30,000 75,000
2 B8 B8C Grade B8C AISI 347 B8M Grade B8M AISI 316 B8T Grade B8T AISI 321 1/4 and larger 30,000 75,000 B8 B8C B8M B8T Grade B8 Grade B8C Grade B8M Grade B8T for High-Temperature Service AISI 304 Strain Hardened AISI 347 Strain Hardened AISI 316 Strain Hardened AISI 321 Strain Hardened 1/4 thr 3/4 Over 3/4 thru 1 Over 1 thru 1-1/4 Over 1-65,000 50,000 65,000 50,000 65,000 50, ,000 90,000 L7 Grade L7 for Low-Temperature Service AISI 4140, 4142 or /2 L7A Grade L7A AISI 4037 L7B Grade L7B AISI 4137
3 L7C Grade LC7 AISI 8740 L43 Grade L43 AISI B8 Grade B8 for Low-Temperature Service AISI 304 B8C Grade B8C AISI 347 B8T Grade B8T AISI 321 1/4 and larger 30,000 75,000 B8F Grade B8F AISI 303 or 303Se B8M Grade B8M AISI 316 B8 B8C Grade B8 Grade B8C AISI 304 AISI 347 3/4 Over 3/4 thru 1 Over 1 thru 1-1/4 Over 1-65,00 50,00 65,00 50,00 B8F Grade B8F AISI 303 or 303Se Grade B8M AISI 316
4 B8M B8T Grade B8T AISI 321 Grade 5 ASTM A449 1 Over 1 to 1 Over 1 to Over thru 3 55,000 92,000 81,000 92,000 81,000 58, , ,000 90,000 Low or Medium Grade 5.1 Sems, No. 6 thru 3/8 120,000 Low Carbon Grade 5.2 Martensitic 1 92, ,000 A325 ASTM A325 Type 1 1/2 thru 1 1-1/8 thru 92,000 81, ,000 Low Carbon A325 ASTM A325 Type 2 High Strength Structural Bolts Martensitic 1/2 thru 1 92, ,000 Atmospheric A325 ASTM A325 Type 3 Corrosion Resisting 1/2 thru 1 1-1/8 thru 92,000 81, ,000 BB ASTM A354 Grade BB 2-1/2 2-3/4 thru 4 75,000 83,000 78,000
5 BC ASTM A354 Grade BC 109,000 99,000 Grade 7 133,000 4 Grade 8 ASTM A354 Grade BD 4 120, , ,000 Alloy or SAE No Grade Grade Modified Elevated Temperature Drawn Steel 120, , ,000 A490 ASTM A490 High Strength Structural Bolts 1/2 thru 120, , ,000 min 170,000 max No Grade No Grade ISO R898 Class 4.6 ISO R898 Class 5.8 All Sizes thru 33,000 36,000 60,000 55,000 57, or ISO R898 Class , ,000 88
6 10.9 or ISO R898 Class , , ,
7 FASTENER IDENTIFICATION MARKING Grade Identification ing Specification Material Nominal Size In. Proof Load Stress ksi Hardness Rockwell Min Max See Note ASTM A563 - Grade 0 69 B55 C32 3,4 ASTM A563 - Grade A 90 B68 C32 3, No ASTM A563 - Grade B over 1 thru 105 B69 C32 3,4 ASTM A563 - Grade C ASTM A563 - Grade C3 ASTM A563 - Grade D ASTM A563 - Grade DH ASTM A563 - Grade DH3 May be Atmospheric Corrosion Resistant Steel May be May be Atmospheric Corrosion Resistant B78 C B78 C38 5, B84 C C24 C C24 C38 5,9 ASTM A194 - Grade B70 7 ASTM A194 - Grade 2 Steel ,8
8 ASTM A194 - Grade 2H ASTM A194 - Grade 2HM ASTM A194 - Grade 4 ASTM A194 - Grade 7 ASTM A194 - Grade 7M See Note 1,2 10 and and and and and C24 C , C24 C C24 C NOTES: 1. In addition to the indicated grade marking, all grades, except A563 grades O, A and B, must be marked for manufacturer identification. 2. The markings shown for all grades of A194 nuts are for cold formed and hot forged nuts. When nuts are machined from bar stock the nut must be additionally marked with the letter 'B'. 3. Nuts are not required to be marked unless specified by the purchaser. When marked, the identification marking shall be the grade letter O, A or B. 4. Properties shown are those of nonplated or noncoated coarse thread hex nuts. 5. Properties shown are those of coarse thread heavy hex nuts. 6. Properties shown are those of coarse thread heavy hex nuts. 7. Properties shown are those of coarse 8-pitch thread heavy hex nuts. 8. Hardnesses are Brinell Hardness Numbers. 9. The nut manufacturer, at his option, may add other markings to indicate the use of atmospheric corrosion resistant steel. 10. Specifications ASTM A563 Carbon and Alloy Steel Nuts. ASTM A194/A194M Carbon and Alloy Steel Nuts for Bolts for High Pressure and High Temperature Service. Shanghai Welfast Enterprise Co., Ltd. Tel: Fax: Web:
ASTM, SAE AND ISO BOLTING MATERIAL
, SAE AND ISO BOLTING MATERIAL Grade Yield SAE J429Grade 1 A307Grades A&B SAE J429Grade 2 Low or Low Carbon Low or 33,000 4 3/4 Over 3/4 to 55,000 33,000 57,000 36,000 60,000 60,000 SAE J429Grade 4 Carbon
More informationStainless Steel & Stainless Steel Fasteners Chemical, Physical and Mechanical Properties
Stainless Steel & Stainless Steel Fasteners Chemical, Physical and Mechanical Properties Stainless steel describes a family of steels highly resistant to tarnishing and rusting that contain at least two
More informationStandard Specification for Carbon and Alloy Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both 1
Designation: A 94/A 94M 0a Endorsed by Manufacturers Standardization Society of the Valve and Fittings Industry Used in USNRC-RDT Standards Standard Specification for Carbon and Alloy Steel Nuts for Bolts
More informationISO INTERNATIONAL STANDARD. Mechanical properties of corrosionresistant stainless steel fasteners Part 1: Bolts, screws and studs
INTERNATIONAL STANDARD ISO 3506-1 Second edition 2009-11-15 Mechanical properties of corrosionresistant stainless steel fasteners Part 1: Bolts, screws and studs Caractéristiques mécaniques des éléments
More informationSubcommittee 3, Connections August 15, 2012
AISI Coittee on Specifications for the Design of Coittee/Subcoittee Ballot: CS11-345C Subcoittee 3, Connections August 15, 2012 SPECIFICATION E3 ed Connections The following design criteria and the requirements
More informationCorrosion Resistant Bolting for Use in the Petroleum and Natural Gas Industries
Corrosion Resistant Bolting for Use in the Petroleum and Natural Gas Industries API SPECIFICATION 20F FIRST EDITION, XXX 201X 1 1. Scope 1.1 Purpose This API specification specifies requirements for the
More informationDesignation: A 193/A 193M 08a
Designation: A 193/A 193M 08a Standard Specification for Alloy-Steel and Stainless Steel Bolting Materials for High Temperature or High Pressure Service and Other Special Purpose Applications 1 This standard
More informationFF-B-575C May 26, 1970 SUPERSEDING Fed. Spec. FF-B-575B September 12, 1960 Fed. Spec. FF-B-571A (In part) January 9, 1934 FEDERAL SPECIFICATION
FEDERAL SPECIFICATION BOLTS, HEXAGON AND SQUARE May 26, 1970 SUPERSEDING Fed. Spec. FF-B-575B September 12, 1960 Fed. Spec. FF-B-571A (In part) January 9, 1934 This specification was approved by the Commissioner,
More informationFree Machining Martensitic stainless steel. Oxidation resistance in continuous service to 1200 F (650 C).
Description 416 is a free machining martensitic grade. The unique production process developed exclusively by Ugitech results in a product that delivers superior productivity and tool life, and improves
More informationResource Guide. Section 4: Ni-Resist
Resource Guide Section 4: Ni-Resist Section 4 Ni-Resist Description of Grades... 4-3 201 (Type 1) Ni-Resist... 4-4 202 (Type 2) Ni-Resist... 4-6 Stock Listings... 4-8 4-2 Ni-Resist Description of Grades
More informationRA17-4 stainless. Introduction
RA17-4 stainless Introduction RA17-4 is an age-hardening martensitic alloy combining high strength with the corrosion resistance of stainless steel. Hardening is achieved by a short-time, simple lowtemperature
More informationAlloys SUPER SQUARE
Alloys ETD 150...8-2 ETD 150 Rounds...8-2 AISI 4140/41L40 - Annealed...8-3 AISI 4140 - Annealed Flats And Squares... 8-4 thru 8-5 AISI 4140 - Annealed Rounds... 8-5 thru 8-6 AISI 4140 Rounds HR Q&T...8-7
More informationCorporation SEAMLESS PIPE
Corporation SEAMLESS PIPE Pipe Applicable Standards ASTM Pipe Code Designations A 106/A 106M Standard Specification for Seamless Carbon Steel Pipe for High-Temperature Service A 312/A 312M Standard Specification
More informationDIVISION: CONCRETE SECTION: CONCRETE ANCHORS DIVISION: METALS SECTION: POST-INSTALLED CONCRETE ANCHORS
0 Most Widely Accepted and Trusted ICC-ES Listing Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ELC-4027 Issued 07/2017 This listing is subject to renewal 07/2018. DIVISION: 03 00 00 CONCRETE
More informationAEROSPACE MATERIAL SPECIFICATION
AEROSPACE MATERIAL SPECIFICATION AMS 2759/3D Issued OCT 1984 Revised FEB 2005 Superseding AMS 2759/3C Treatment Precipitation-Hardening Corrosion-Resistant and Maraging Steel Parts 1. SCOPE: This specification,
More informationDIVISION: CONCRETE SECTION: CONCRETE ANCHORS DIVISION: METALS SECTION: POST-INSTALLED CONCRETE ANCHORS
0 Most Widely Accepted and Trusted ICC-ES Listing Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ELC-4027 Issued 07/2017 This listing is subject to renewal 07/2018. DIVION: 03 00 00 CONCRETE
More informationSTAINLESS STEEL STAINLESS HALF-ROUNDS STAINLESS SQUARES 303, 304/304L, 316L, 416, 17-4,
STAINLESS STEEL TECHNICAL DATA and APPLICATIONS Grade 201...9-2 Grade 303 and 303 G&P...9-3 Grade 304 and 304L...9-4 Grade 316L and 316L BSQ...9-5 Grade 410...9-6 Grade 416 and 416 PSQ...9-7 Grade 420...9-8
More informationMaterial and Process. Specification
s 146-67- 1 of 7 Document By: Title Name 1. Purpose 1.1 This document defines approved revision levels of Material and Process specifications used by Onboard Systems. This list is for supplier reference
More informationCOPPER PRODUCTS. 145 COPPER PRODUCTS Half Hard Tellurium Rounds
COPPER PRODUCTS 110 COPPER PRODUCTS Rounds... 12-2 Squares... 12-2 Flats - Square Edge...12-3 thru12-4 Flats - Full Round Edge (FRE)... 12-5 Cold Rolled Sheet... 12-6 110 Quarter Hard Copper Sheet... 12-6
More informationSTAINLESS STEEL SHEETS
STAINLESS & NICKEL ALLOY CHATHAM STEEL CORPORATION 59 STAINLESS STEEL SHEETS TYPE 04, 04L, 6, 6L No. 2B Finish Cold Rolled, Annealed *No. 2D Finish No. Finish Polished One Side No. 4 Finish Polished One
More informationAEROSPACE MATERIAL SPECIFICATION
AEROSPACE MATERIAL SPECIFICATION Licensed to Juan Rodriguez AMS 5754M Issued MAY 1954 Revised AUG 2007 Superseding AMS 5754L Nickel Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings 47.5Ni
More informationSingle & Back-to-Back StiffWall Column Product Profile
Single & Back-to-Back StiffWall Column Product Profile Material Properties ASTM A1003/A1003M or ASTM A653/A653M, Grade 50 (340), 50ksi (340MPa) minimum yield strength, 65ksi (450 MPa) minimum tensile strength,
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005. ELEMENT NEWTOWN 2 Pheasant Run Newtown, PA Douglas Reed Phone: MECHANICAL
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 ELEMENT NEWTOWN 2 Pheasant Run Newtown, PA 18940 Douglas Reed Phone: 267 759 3886 MECHANICAL Valid To: April 30, 2016 Certificate Number: 0478.01 In recognition
More informationSection 906. STRUCTURAL STEEL
906.01 Section 906. STRUCTURAL STEEL 906.01. General Requirements. Finished rolled shapes must be free from imperfections that affect strength and durability in accordance with ASTM A 6. Rolled shapes
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 3506-1 Second edition 2009-11-15 Mechanical properties of corrosionresistant stainless steel fasteners Part 1: Bolts, screws and studs Caractéristiques mécaniques des éléments
More informationCopper & Copper Alloys CuNi1Si (OF 2403)
Copper and Copper Alloys Page 1 of 5 no responsibility is taken for the correctness of this information 04/2014 Cu Zn Pb Sn Fe Mn Ni Al Si As Co Cr Others Min. Rem. - - - - - 1.0-0.4 - - - - Max. - - 0.02-0.2
More informationE-Z-Ground Grounding Systems. Ground Wire Size. Water Pipe Size. 1/2 in /4 in. 2 in /2 in. 3-1/2 in TB
Waterpipe Ground Clamps Cat. No. Ground Wire Size Water Pipe Size 2-TB 1/2 in., 3/4 in., 1 or rebar 4-10 3-TB 1-1/4 in., 1-1/2 in. or 2 in. #6, #4, 4 2-1/2 in., 3 in. or 3-1/2 in. #2 WG 5-TB 4 in., 4-1/2
More informationDIVISION: CONCRETE SECTION: CAST IN CONCRETE ANCHORS DIVISION: CONCRETE ANCHORS REPORT HOLDER: DEWALT
0 Most Widely Accepted and Trusted ICC ES Listing Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ELC 3657 Issued 05/2017 This listing is subject to renewal 05/2018. DIVISION: 03 00 00 CONCRETE
More informationINDUSTRIAL THREADED PRODUCTS, INC.
INDUSTRIAL THREADED PRODUCTS, INC. (800) 976-Bolt PRODUCTS & SERVICES CORPORATE HEADQUARTERS 3580 Firestone Blvd., Santa Fe Springs, CA 90670 (562) 802-4626 (74) 52-5902 Fax: (562) 802-464 BRANCH SALES
More informationNORRIS. Drive Rods. Engineered performance. Designed tough.
NORRIS Drive Rods Engineered performance. Designed tough. 1 (25,4 mm) Norris Drive Rods with 7/8 (22,23 mm) fullsize couplings Tubing size Improvement 27/8 (73,0 mm) 37% improvement in flow area when compared
More informationONE-STOP SHOP FOR AEROSPACE MATERIALS
ONE-STOP SHOP FOR AEROSPACE MATERIALS Scope Metals Group is a leading distributor and supplier of finished and semi-finished metals products and engineered plastics products to industrial manufacturers.
More informationIt is our intent to always maintain the highest level of quality metals obtainable from our mill sources.
This stock catalog contains the sizes, weights and descriptions of all standard Steel, Brass, Bronze and Dura-Bar Cast Iron items that are available from stock for immediate delivery. However, new items
More informationEVALUATION REPORT. PFC-5551 Reissued April 1, Filing Category: DESIGN Steel (038)
ICBO Evaluation Service, Inc. 5360 WORKMAN MILL ROAD WHITTIER, CALIFORNIA 90601-2299 A subsidiary corporation of the International Conference of Building Officials EVALUATION REPORT Copyright 2001 ICBO
More informationSubway Cars. Applications Potential
301 STAINLESS STEEL P R O D U C T D ATA B U L L E T I N Aircraft Structural Parts Roof Drainage Cooking Utensils Automotive Trim Subway Cars Applications Potential Type 301 is an austenitic chromium-nickel
More informationDIVISION: METALS SECTION: METAL FASTENINGS REPORT HOLDER: LINDAPTER
0 Most Widely Accepted and Trusted ICC-ES Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-3330 Reissued 03/2017 This report is subject to renewal 03/2018. DIVISION: 05 00 00 METALS SECTION:
More informationCast steel: Group of ASTM standards for steel castings and forgings
Cast steel: Group of ASTM standards for steel castings and forgings Abstract: This group of ASTM specifications covers standard properties of steel and iron castings and forgings for valves, flanges, fittings,
More informationApplications Potential
P R O D U C T D A T A B U L L E T I N STAINLESS 301STEEL UNS S30100 High Strength and Good Ductility When Cold Worked Excellent Corrosion Resistance Readily Welded Readily Formed and Drawn Economical Oxidation
More informationDIVISION: CONCRETE SECTION: CONCRETE ANCHORS DIVISION: METALS SECTION: POST INSTALLED CONCRETE ANCHORS
0 Most Widely Accepted and Trusted ICC ES Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3572 Reissued 04/207 This report is subject to renewal 04/209. DIVISION: 03 00 00 CONCRETE SECTION:
More informationDIVISION: EARTHWORK SECTION: BORED PILES REPORT HOLDER: CANTSINK MANUFACTURING, INC. 71 FIRST AVENUE LILBURN, GEORGIA 30047
0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-1559 Reissued 12/2016 This report is subject to renewal 12/2018. DIVISION: 31 00
More informationDIVISION: EARTHWORK SECTION: BORED PILES REPORT HOLDER: HELICAL ANCHORS, INC BOONE AVENUE, NORTH MINNEAPOLIS, MINNESOTA 55428
0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-3982 Reissued 09/2017 This report is subject to renewal 09/2019. DIVISION: 31 00
More informationSECTION CRL50 AND CRL51 HEAVY GLASS TOP HUNG SLIDING DOOR SYSTEMS
SECTION 08 32 20 CRL50 AND CRL51 HEAVY GLASS TOP HUNG SLIDING DOOR SYSTEMS Page 1 of 6 USE THIS SECTION WHEN SPECIFYING OVERHEAD SUPPORTED GLASS PANEL PARTITIONS. SECTION INCLUDES OVERHEAD TRACK ASSEMBLY,
More informationSTAINLESS STEEL STAINLESS STEEL
STAINLESS STEEL The special characteristic of stainless steels is that they have a resistance to corrosion that is significantly higher with respect to other steels; some of them also have an excellent
More informationCantilevered Rail System
Knight Global's Cantilevered Rail Systems are designed to eliminate the need for a four post floor structure system. It provides an alternative to workstations with minimal floor space. A wide range of
More informationDIVISION: CONCRETE SECTION: CONCRETE ANCHORS DIVISION: METALS SECTION: POST INSTALLED CONCRETE ANCHORS
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3931 Reissued 07/2017 This report is subject to renewal 07/2019. DIVISION: 03 00
More informationThis document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 683-1 Third edition 2016-07-01 Heat-treatable steels, alloy steels and free-cutting steels Part 1: Non-alloy steels for quenching and tempering Aciers pour traitement thermique,
More informationAEROSPACE MATERIAL SPECIFICATION
AEROSPACE MATERIAL SPECIFICATION AMS 5643Q Issued OCT 1951 Revised JAN 2003 Superseding AMS 5643P Steel, Corrosion-Resistant, Bars, Wire, Forgings, Tubing, and Rings 16Cr - 4.0Ni - 0.30Cb - 4.0Cu Solution
More informationStandard Specification for Carbon and Alloy Steel Bars Subject to End-Quench Hardenability Requirements 1
Designation: A 304 04 An American National Standard Standard Specification for Carbon and Alloy Steel Bars Subject to End-Quench Hardenability Requirements 1 This standard is issued under the fixed designation
More informationLOAD BEARING ROLLER ASSEMBLIES Engineering Data Installation Notes
Installation Notes INSTALLING STUD TYPE LOAD BEARING ROLLER ASSEMBLIES Mounting holes should be machined to the nominal stud size within +.001/-.000 (+.025mm / -.000mm) tolerance. When properly aligned,
More informationStructural vs Nonstructural Members. Roger LaBoube, Ph.D., P.E. Wei-Wen Yu Center for Cold-Formed Steel Structures
Structural vs Nonstructural Members Roger LaBoube, Ph.D., P.E. Wei-Wen Yu Center for Cold-Formed Steel Structures Behavior of Cold-Formed Steel Members STEEL DESIGN SPECIFICATIONS Type of steel Specification
More informationThe ATI 17-4 precipitation hardening stainless steel (S17400) is covered by the following wrought product specifications.
ATI 17-4 Precipitation Hardening Stainless Steel (UNS S17400) INTRODUCTION ATI 17-4 precipitation hardening stainless steel (S17400), Type 630, is a chromium-nickel-copper precipitation hardening stainless
More informationISO INTERNATIONAL STANDARD. Bolted bonnet steel gate valves for the petroleum, petrochemical and allied industries
INTERNATIONAL STANDARD ISO 10434 Second edition 2004-07-15 Bolted bonnet steel gate valves for the petroleum, petrochemical and allied industries Robinets-vannes en acier à chapeau boulonné pour les industries
More informationSTUDY: STAGE : ENGLISH VERSION Aerospace series Bolt Countersunk head, Short thread Inch series
DRAFT pren6114 Edition : P5 Date: Dec.2007 STUDY: STAGE : Ref. : Superseding Ref. : ENGLISH VERSION Aerospace series Bolt Countersunk head, Short thread Inch series Série Aérospatiale Vis, tête fraisée,
More informationDownloaded from DETAIL SPECIFICATION SHEET INSERT, SCREW THREAD, LOCKED IN, KEY-LOCKED, MINIATURE AND LIGHTWEIGHT
INCH-POUND DETAIL SPECIFICATION SHEET 21 June 2012 SUPERSEDING MS51830E 9 March 1992 INSERT, SCREW THREAD, LOCKED IN, KEY-LOCKED, MINIATURE AND LIGHTWEIGHT This specification is approved for use by all
More informationThis document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 683-2 Second edition 2016-07-01 Heat-treatable steels, alloy steels and free-cutting steels Part 2: Alloy steels for quenching and tempering Aciers pour traitement thermique,
More informationSTOCKIST SUPPLIERS & EXPORTERS:
PIPES & TUBES: Stainless Steel: ASTM A 312, A 213, A 213, A 249, A 269, A 358, A 240, A 276 Type: 202, 304, 304L, 304, 304H, 316, 316L, 316Ti, 321, 321H, 317, 317L, 310, 310S, 409, 410, 420, 430 etc. Carbon
More informationStandard Specification for Stainless Steels for Surgical Instruments 1
Designation: F 899 02 Standard Specification for Stainless Steels for Surgical Instruments 1 This standard is issued under the fixed designation F 899; the number immediately following the designation
More informationMATERIAL ALLOWABLE STRENGTH DATA
Design Allowables Data Sheet A B C D E Metallic Materials Threaded Fasteners Wire Ropes and Cables Wood Rivets Issue Status Iss No. Date Change Description 1 29/06/06 Initial Issue, Metallic Materials
More informationESR ICC Evaluation Service, Inc. Reissued January 1, 2008 This report is subject to re-examination in one year.
ESR-1967 Reissued January 1, 2008 This report is subject to re-examination in one year. ICC Evaluation Service, Inc. www.icc-es.org Business/Regional Office # 5360 Workman Mill Road, Whittier, California
More informationProduct Test Report. PTR-3074 Swagelok Company. Rev. B Solon Road January 2015 Solon, Ohio U.S.A. Page 1 of 5
Solon, Ohio 44139 U.S.A. Page 1 of 5 TITLE Resistance of SAF 2507 Super Duplex Stainless Steel to Chloride Stress Corrosion Cracking PRODUCT TESTED Test samples were machined from Sandvik SAF 2507 solution-annealed
More informationUgitech Stainless steel solutions for the oil and gas industry
Ugitech Stainless steel solutions for the oil and gas industry 02 Stainless steel solutions for the oil and gas industry Ugitech and the Oil and Gas industry The world s conventional oil reserves are seriously
More informationDAHE STEEL STRUCTURE CO.,LTD.
DAHE ENTERPRISES LIMITED DAHE STEEL STRUCTURE CO.,LTD. FOREWORD FOREWORD Dahe Enterprises Ltd registers in Hong Kong. She owns two sole-investment companies Dahe Steel Structure (HK) Co., Ltd & Nanhai
More informationNotes Changed note Date. 1 (A) Changed template 09 / 07 / 2008
Revisions Notes Changed note Date 1 (A) Changed template 09 / 07 / 2008 2 Changed template. Clause 12.5.4.1 hot-rolled steel added. Clause 12.5.4.2, 12.5.2.4, 12.5.3.4, 12.5.4.4, 12.5.5.4, 12.5.6.4, 12.5.7.4
More informationSTAINLESS STEEL BRIGHT BARS
STAINLESS STEEL BRIGHT BARS Stainless Steel Bright Bars Stainless Steel Bright Bars Viraj is equipped with a state-of-the-art, continuous hardening and tempering furnace for the heat treatment of Ferritic
More informationSURFACE VEHICLE STANDARD
400 Commonwealth Drive, Warrendale, PA 15096-0001 SURFACE VEHICLE STANDARD J403 Issued 1911-06 Revised 2001-11 Superseding J403 JUN2000 REV. NOV2001 s of SAE Carbon Steels 1. Scope In 1941, the SAE Iron
More informationObjective. Who is involved. Before final decisions are made
New San Francisco-Oakland Bay Bridge Self Anchored Suspension Bridge By: Brian Maroney, PE, Dr. Engr. Deputy Toll Bridge Program Manager California Department of Transportation Objective Carry out an open
More informationHilti, Inc South 122 nd East Avenue Tulsa, OK
Attached are page(s) from the 2014 Hilti North American Product Tech Guide. For complete details on this product, including data development, product specifications, general suitability, installation,
More informationSTAINLESS STEELS UTILITY FERRITIC. T e c h n i c a l B r o c h u r e. U-3CR12L S U-410S 410S S41008 U-3CR12
R T e c h n i c a l B r o c h u r e UTILITY FERRITIC STAINLESS STEELS Unity AISI UNS EN U-3CR12 U-3CR12L S43 1.43 U-4S 4S S48 COLUMBUS STAINLESS [Pty] Ltd www.columbusstainless.co.za Introduction 3CR12
More informationREPORT HOLDER: MITEK USA, INC. (FORMERLY USP STRUCTURAL CONNECTORS) SOUTHCROSS DRIVE, SUITE 200 BURNSVILLE, MINNESOTA EVALUATION SUBJECT:
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 43 6587 (56) 699 0543 www.icc es.org ESR 3754 Reissued 09/07 This report is subject to renewal 09/09. DIVISION: 03 00 00 CONCRETE
More informationCorrelation of Hardness Values to Tensile Strength
Correlation of Hardness Values to Tensile Strength Semih Genculu, P.E. Various procedures and approaches are utilized to determine if a given material is suitable for a certain application. The material
More informationHigh Strength Epoxy Tested in Accordance with ICC-ES AC308
ADHESIVE ANCHORING SPECIALISTS High Strength Epoxy Tested in Accordance with ICC-ES AC308 DESCRIPTION/SUGGESTED SPECIFICATIONS* The epoxy resin and hardener are completely mixed as they are dispensed from
More informationCHEMICAL /4" 3/8" to 5/8" /8" 3/4" to 1-1/4" 1 10
194 ASTM A193 GRADE B7 HIGH-STRENGTH CARBON, ZINC PLATED (ASTM B 633 YELLOW DICHROMATE) B7 (AISI 414) anchor rod is supplied with nuts meeting the requirements of ASTM Specification A 194, Grade 2H (ASTM
More informationIntroduction Manufacturing Process Manufacturing Process and Quality Control Standard Dimensions and Weights Chemical composition and mechanical
C O N T E N T S Introduction Manufacturing Process Manufacturing Process and Quality Control Standard Dimensions and Weights Chemical composition and mechanical properties Sections Head Hardened Rails
More informationTRANSPORT II " 10.5" MOUNTING POSTS FENCE LINE POST. Classic gate shown GATE OPENING CANTILEVER GATE SAFETY WARNING
TRANSPORT ESTATE TRANSPORT IS TRANSPORT LINK ADAPTRACK 2"sq x.25" UPRIGHTS & DIAGONAL BRACES 1"sq x.125" PICKETS GATE TRACKS PRE-DRILLED FOR LEFT OR RIGHT OPENINGS FENCE LINE POST 13.8125" 10.5" MOUNTING
More informationAISI A2 Cold work tool steel
T OOL STEEL FACTS AISI A2 Cold work tool steel Great Tooling Starts Here! General AISI A2 is an air- or oil hardening chromiummolybdenum-vanadium alloyed tool steel characterized by: Good machinability
More informationMaterials Carbon Steel and Malleable Iron are used in the manufacture of concrete inserts. Stainless Steel and other materials are available.
Concrete inserts offered in this section are designed to provide a pre-set support point in concrete ceilings, walls, and floors. A range of inserts with varying design loads are available. Materials Carbon
More informationASME B31.3 Process Piping. 19. What s Different in B31.1
ASME B31.3 Process Piping Charles Becht IV, PhD, PE Don Frikken, PE Instructors BECHT ENGINEERING COMPANY, INC. What s Different in B31.1-1 19. What s Different in B31.1 Scope Organization of the Code
More informationWe manufactures copper & copper based alloys mainly brass / bronzes extrusion & drawn quality rods / bars
EXTRUDED RODS INTRODUCTION` We manufactures copper & copper based alloys mainly brass / bronzes extrusion & drawn quality rods / bars in different shapes like round, hex, square, rectangular & flat. We
More informationLicensed Copy: John May, Powertrain Ltd., February 20, 2002, Uncontrolled Copy, (c) BSI
BRITISH STANDARD BS 70-3: Incorporating Amendment Nos. 1 and 2 Specification for Wrought steel for mechanical and allied engineering purposes Part 3: Bright bars for general engineering purposes BS70-3:
More informationCarpenter CTS BD1 Alloy
Type Analysis Carbon 0.85 to 0.95 % Manganese 1.00 % Phosphorus 0.040 % Sulfur 0.030 % Silicon 1.00 % Chromium 15.00 to 17.00 % Molybdenum 0.50 % Iron 79.48 to 81.58 % General Information Description Carpenter
More informationSEWER FORCE MAIN HDPE PIPE
SECTION 15150 SEWER FORCE MAIN HDPE PIPE PART 1: GENERAL 1-1 DESCRIPTION: This specification governs the material, pipe, fittings, joining methods and general construction practice for High Density Polyethylene
More informationCopper and Copper Alloy Tube, Pipe and Fittings COPPER and COPPER ALLOY TUBE and PIPE Seamless Copper Pipe: Copper pipe is almost pure copper manufactured to the requirements of ASTM B 42 - Standard Specification
More informationCustom-Designed Clamps. Machined Versions. Online Configurator for Custom-Designed Clamps A56.
Custom-Designed Clamps Machined Versions Custom-designed clamping systems for pipes, tubes, hoses, cables and other components according to customer`s specifications or based on developments, made of thermoplastics,
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005. TSP / USB LABORATORY South Main Street Houston, TX Lester Burgess Phone:
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 TSP / USB LABORATORY 1 12895 South Main Street Houston, TX 77035 Lester Burgess Phone: 713 726 1000 MECHANICAL Valid To: June 30, 2018 Certificate Number: 0929.01
More informationMartensitic. stainless steels. Types 410, 420, 425 Mod, and 440A TECHNICAL DATA BLUE SHEET GENERAL PROPERTIES APPLICATIONS PRODUCT FORM
TECHNICAL DATA BLUE SHEET Martensitic Stainless Steels s 410, 420, 425 Mod, and 440A GENERAL PROPERTIES Allegheny Ludlum s 410, 420, 425 Modified, and 440A (see composition on Page 2) are hardenable, straight-chromium
More informationGlobal Metal Solutions Oil & Gas Aerospace Naval & Marine Power Generation Motor Sport Metalworking Medical
Global Metal Solutions Oil & Gas Aerospace Naval & Marine Power Generation Motor Sport Metalworking Medical Our pedigree Maher supplies advanced alloys for high performance applications. Founded in Sheffield
More informationSTANDARD FERRITIC STAINLESS STEELS
T e c h n i c a l B r o c h u r e STANDARD FERRITIC STAINLESS STEELS Unity AISI UNS EN U-40910 409 S40910 1.4512 U-430 430 S43000 1.4016 U-430DDQ 430 S43000 1.4016 U-439 439 S43035 1.4510 - S43940 U-1.4509
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 15761 First edition 2002-12-15 Steel gate, globe and check valves for sizes DN 100 and smaller, for the petroleum and natural gas industries Robinets-vannes, robinets à soupape
More informationDuctility and Use of Titanium Alloy and Stainless Steel Aerospace Fasteners
University of South Florida Scholar Commons Graduate Theses and Dissertations Graduate School January 2015 Ductility and Use of Titanium Alloy and Stainless Steel Aerospace Fasteners Jarrod Talbott Whittaker
More informationPRELIMINARY INVESTIGATIONS OF LOW-NICKEL STAINLESS STEELS FOR STRUCTURAL APPLICATIONS
PRELIMINARY INVESTIGATIONS OF LOW-NICKEL STAINLESS STEELS FOR STRUCTURAL APPLICATIONS J. Kerr and R. Paton Mintek, Private Bag X3015, Randburg. 2125. South Africa. E-mail: jonathank@mintek.co.za ABSTRACT
More informationQuick Tie System (QTS) TER No
Quick Tie System (QTS) TER No. 0910-01 Quick Tie Products, Inc. 13300 Vantage Way Jacksonville, FL 32218 904-281-0525 904-281-0526 (fax) quicktieproducts.com Issue Date: October 20, 2009 Updated: March
More informationDIVISION: CONCRETE SECTION: CONCRETE ANCHORS DIVISION: METALS SECTION: POST-INSTALLED CONCRETE ANCHORS
0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 43-6587 (56) 699-0543 www.icc-es.org ESR-384 Reissued 0/07 This report is subject to renewal 0/09. DIVISION: 03 00 00 CONCRETE
More informationRosemount 9901 Chambers for Process Level Instrumentation
Reference Manual Rosemount 9901 Chambers for Process Level Instrumentation Reference Manual Safety instructions These safety instructions are to be read and used in conjunction with the manual of the
More informationDIVISION: CONCRETE SECTION: CONCRETE ANCHORS DIVISION: METALS SECTION: POST INSTALLED CONCRETE ANCHORS
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3576 Reissued 07/2017 This report is subject to renewal 07/2018. DIVISION: 03 00
More informationISO INTERNATIONAL STANDARD. Fasteners Preloading test for the detection of hydrogen embrittlement Parallel bearing surface method
INTERNATIONAL STANDARD ISO 15330 First edition 1999-09-01 Fasteners Preloading test for the detection of hydrogen embrittlement Parallel bearing surface method Éléments de fixation Essai de précharge pour
More informationSTAINLESS STEELS. Chromium and nickel content in the various groups of stainless steels
These steels contain a high percentage of chromium and sometimes other alloys and have been designed to prevent different types of corrosion. There are two kinds of corrosion: dry corrosion (often named
More informationDIVISION: EARTHWORK SECTION: BORED PILES REPORT HOLDER: MAGNUM PIERING, INC. 156 CIRCLE FREEWAY DRIVE CINCINNATI, OHIO 45246
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2997 Reissued 05/2017 This report is subject to renewal 05/2018. DIVISION: 31 00
More informationHigh Strength Epoxy tested in accordance to ICC-ES AC308
ADHESIVE ANCHORING SPECIALISTS High Strength Epoxy tested in accordance to ICC-ES AC308 2006 IBC Compliant ICC-ES Report No. 1137 DESCRIPTION/SUGGESTED SPECIFICATIONS* The epoxy resin and hardener are
More information41003 STAINLESS STEEL
41003 STAINLESS STEEL D ATA S H E E T Formable and Weldable in Heavy Sections Refined Grain Structure Leads to Good Toughness Ferritic as Annealed Low Cost AK Steel 41003 is an economical ferritic stainless
More informationATI 718 ATI 718. Technical Data Sheet. Nickel-Base Superalloy INTRODUCTION FORMS AND CONDITIONS AVAILABLE SPECIFICATIONS. (UNS Designation N07718)
ATI 718 Nickel-Base Superalloy (UNS Designation N07718) INTRODUCTION ATI 718 alloy (N07718) is an austenitic nickel-base superalloy which is used in applications requiring high strength to approximately
More informationSanta Ana Operations. Military Standard Fasteners, Inch & Metric Section 1 - Ring-Locked Studs
Santa Ana Operations Military Standard Fasteners, Inch & Metric Section 1 - Ring-Locked Studs INTRODUCTION ROSÁN IS A COMPANY WITH OVER FORTY YEARS OF CREATIVE DESIGN, DEVELOPMENT AND MANUFACTURING EXPERIENCE.
More information