Modification of epoxy adhesives to enhance glue ductility in relation to wood adherends
|
|
- Brittney Stafford
- 6 years ago
- Views:
Transcription
1 Modification of epoxy adhesives to enhance glue ductility in relation to wood adherends Jan Vanerek Anna Benesova, Ámos Dufka, Nikol Zizkova and Rostislav Drochytka FACULTY OF CIVIL ENGINEERING BRNO UNIVERSITY OF TECHNOLOGY CZECH REPUBLIC
2 Experiment Objective To increase the durability of epoxy adhesives Possible usage for load-bearing structures (classification type I - EN 301, requiring durability during external exposure and stability at temperatures above 50 C) Fulfillment of standard requirements sufficient shear tensile strengths after hygrothermal exposure (exposures A1-5 defined in EN 302-1) the ability to withstand the strain arising from volume changes of wood adherends (delamination test after accelerated aging test according to EN comparable to ASTM D 2559). Currently there are non-uniform results from epoxy/wood durability testing, in spite of the huge development of the FRP branch.
3 Introduction - Types of Epoxy Modification 1. Reinforcing process of epoxy adhesives: Epoxy adhesives are optimized for delamination resistance a) with reinforcements (suitable aspect ratio) to ensure the flexible behavior of the adhesives a) nanocellulose fibers (optimal disintegration process to avoid agglomeration of cellulose) fracture delamination improved significantly with the addition of NFC (fracture toughness increased about 61% for 1wt.% of NFC to CF/epoxy material) b) with fillers, mostly in nano-scale a) Nano-clay particles only 0.5 wt.% could improve the fracture toughness by 20%, 3.0 wt.% by 50% higher than the neat epoxy. b) Carbon-black 2.0 wt.% of CB content leads to improving the fracture toughness by 18% (ductile fracture mode) 2. Modification of application process: a) Positive results with proper wood penetration processes (wood cell stabilization theory) using different types of primer (MME, HMR) increase the ability of the bondline to withstand the wood volume changes.
4 Material - adhesives Using a two-step application penetration to stabilize the interfacial wood cell walls and distribute the expansion /concentration differences more into the wood structure 120 g/m 2 ), adhesive layer (200 g/m 2 ), both-side application, pressure clamping 1.0 MPa for 10 hours, Primer - epoxy resin CHS 474 and curing agent Telalit 0492 (SPOLCHEMIE, Czech Rep.) σ t = 59.2 N/mm 2, CHS 474: Pa.s; 0492: Pa.s Epoxy resin CHS 531 and curing agent Telalit 0492 (SPOLCHEMIE, Czech Rep.) σ t = 50.1 N/mm 2, CHS 531: Pa.s; Telalit 0492: Pa.s
5 Materials Wood Spruce (Picea abies) f m = 81.1 N/mm 2, E m = N/mm 2, ρ 12 = 465 kg.m 3 flatsawn timber of 25 mm thickness, surface treatment - planed Reinforcing agent Carbon black (Rubber gas black, ORION Engineered Carbons, GERMANY) CK3 achieved by gas black method, pour density 380 g/dm 3 ; Different amount 0.5; 1.0; 2.0 and 3.0 wt.% of epoxy resin.
6 Modification of epoxy primer Epoxy basis 1.CB was first dispersed in a solvent agent (chloroform CHCl 3 ) using a magnetic heat stirrer plate at 45 C (150 rpm) for 15 minutes; 2.epoxy resin was mixed with the suspension and subjected to shear mixing (150 rpm) for 15 min at 45 C; 3.sonication of suspension for 10 minutes in water bath of constant 20 C temperature using Bandelin 3200 ultrasound apparatus at 70% amplitude; 4.nanofiller chloroform mixture was degassed in s vacuum dryer at 75 C for 12 h to eliminate the remaining solvent; 5.stoichiometric amount of curing agent was added into the mixture before application onto the wood surface.
7 Durability testing Hygrothermal exposure - short term durability test according to EN (A1, A4, A5) was carried out to observed wood/epoxy bond behavior Table 1: Types of exposition prior to tensile shear testing Treatment Climatic treatment Specification A1 Standard climate 7 days 20 ºC/65% A2 Immersion in cold water 7 days 20 ºC/65% 4 days in water (15±5 ºC) Tested in wet state A3 Immersion in cold water 7 days 20 ºC/65% 4 days immersion in water (15±5 ºC), conditioning at 20 ºC/65% Tested in dry state A4 Immersion in boiling water 7 days 20 ºC/65% 6 hours in boiling water 2 hours immersion in water (15±5 ºC), Tested in wet state A5 Immersion in boiling water 7 days 20 ºC/65% 6 hours in boiling water 2 hours immersion in water (15±5 ºC) 7 days conditioning at 20 ºC/65% Tested in dry state Treatment Min. mean value of tensile shear strength (MPa) Type I A1 10,0 A2 6,0 A3 8,0 A4 6,0 A5 8,0
8 Testing Tensile shear strength modified single lap joint test specimens with dimension of mm (EN 302-1), with thin bondline (<0,1mm), single lap shear area of mm (notch of 4 mm width), 12 pcs per each exposure treatment, speed of tensile testing 0,1 mm/min; extensometr with gauge length of 50 mm, Tensile strength and MOE of neat and modified epoxy resin, EN Wood failure mode 10% percentage stage graded of shear area, wood failure (Cohesive Failure), DSC complementary assessment for T g evaluation SEM, AFM micrograph complementary for dispergation of nano particles in resin, AFM for detailed bondline evaluation.
9 Tensile shear strength [N.mm -2 ] Tensile shear strength [N.mm -2 ] Results tensile shear strengths A1 exposure A4 exposure A5 exposure A1 exposure A4 exposure A5 exposure ref 1.0 MCB 3.0 MCB 5.0 MCB 10.0 MCB content of micro carbon black in epoxy primer [wt.%] 0.00 ref 0.5 NCB 1.0 NCB 2.0 NCB 3.0 NCB content of nano carbon black in epoxy primer [wt.%] micro carbon black fillers in epoxy primer nano carbon black fillers in epoxy primer significant aspect could be seen in exposure of boiling test (A4 treatment), where specimens with micro carbon black fillers decrease strength of ca. 75 %; huge conglomeration of carbon black cause local huge interfacial strain; contrary, no significant drop was observed in A4 treatment when nano carbon black reinforcing agent was applied in primer with 0,5 wt.% of nano carbon black; additionally decrease of 40% in primer with 3,0 wt.% of nano carbon black.
10 Cohesive failure [%] Cohesive failure [%] Results wood failure (cohesive) criterion A1 exposure A4 exposure A5 exposure 0 ref 1.0 MCB 3.0 MCB 5.0 MCB 10.0 MCB content of micro carbon black in epoxy primer [wt.%] ref 0.5 NCB 1.0 NCB 2.0 NCB 3.0 NCB content of nano carbon black in epoxy primer [wt.%] A1 exposure A4 exposure A5 exposure micro carbon black fillers in epoxy primer nano carbon black fillers in epoxy primer Tensile shear strength specimen with 0.5 NCB fillers in epoxy primer resin
11 Results wood failure (cohesive) criterion cohesive failure in softwood structure mostly observed in early wood of annual ring, where better penetration into the cell wood structure adhesion failure wood imperfection (knots), insufficient penetration into the wood structure (could be confirmed by EPI-fluorescence microscopy), agglomeration of MCB
12 Results influence of NCB for epoxy characteristics Sample Tensile strength N.mm -2 Mean value S.D. Modulus of Elasticity N.mm -2 Mean value S.D. Relative strain % Mean value Neat resin , CHS NCB ,
13 Results SEM analyze for dispersion of MCB and NCB in epoxy Surface of fracture area for MFC/epoxy adhesive (left, 10,000x magn.), and 0.5NFC/epoxy adhesive (middle, 10,000x magn.), agglomerates of 0.5NFC in epoxy (right, 100,000x magn.)
14 Concluding remarks epoxy modification using micro and nano carbon blacks were evaluated for the primer layer. The micro carbon black caused local stress concentrations on the bondline resulting in total adhesion failures after hygrothermal exposures. In contrast, a significant aspect of carbon black deagglomerization using the ultrasonication treatments was found to enhance the stabilization of wood adherend by such modified epoxy primer. The optimum content, fulfilling criteria of strength and cohesive failure, was 0.5wt.% for nano carbon black reinforcing agents. This improvement was found despite the fact that better resin characteristics (ultimate strength, modulus of elasticity, strain) were not confirmed for 0.5NCB/epoxy primer.
15 The optimum penetration of modified primer into the wood structure plays the most important role to the stabilize wood surface to better interfere with internal forces arising in the glued bondline. In the spruce test samples, cohesive failures were primarily detected in the annual rings of the early wood, confirming easier adhesive penetration. According to SEM observation of fracture MFC/epoxy and NFC/epoxy surfaces, the agglomeration of reinforcing agents even in both scales influence the occurrences of cracks or other imperfections.
16 Thank you for your attention.
Heating elements shall not be used for FRP tank-containers including tank swap bodies.
Chapter 6.9 6.9.1 General Requirements for the design, construction, equipment, type approval, testing and marking of fibre-reinforced plastics (FRP) tank-containers including tank swap bodies NOTE: For
More informationDURABILITY OF PRESSURE SENSITIVE ADHESIVE JOINTS
DURABILITY OF PRESSURE SENSITIVE ADHESIVE JOINTS Paul Ludwig Geiss, Daniel Vogt Kaiserslautern University of Technology, Faculty Mechanical and Process Engineering, Workgroup Materials and Surface Technologies
More informationTHE EFFECT CLAY ON THE MECHANICAL PROPERTIES OF EPOXY RESINS SUBJECTED TO HYGROTHERMAL AGEING
THE EFFECT CLAY ON THE MECHANICAL PROPERTIES OF EPOXY RESINS SUBJECTED TO HYGROTHERMAL AGEING Salah U. Hamim 1 & Raman P. Singh 1 1 Mechanical and Aerospace Engineering Oklahoma State University Helmerich
More informationExperimental investigation of the use of CFRP grid for shear strengthening of RC beams
Journal of Asian Concrete Federation Vol. 2, No. 2, Dec. 2016, pp. 117-127 ISSN 2465-7964 / eissn 2465-7972 http://dx.doi.org/10.18702/acf.2016.12.2.2.117 Experimental investigation of the use of CFRP
More informationThe Flexural Properties of Glass Fabric/Epoxy -Rigid Polyurethane Foam Core Sandwich Composites at Different Span to Depth Ratios and Densities
Proc. of the Intl. Conf. on Advances In Engineering And Technology - ICAET-214 ISBN: 978-1-63248-28-6 doi: 1.15224/ 978-1-63248-28-6-3-87 The Flexural Properties of Glass Fabric/Epoxy -Rigid Polyurethane
More informationExperimental Evaluation of Tensile Strength and Young s Modulus of Woven Jute fiber and Polyurethane Composite
From the SelectedWorks of Innovative Research Publications IRP India Summer August 1, 2015 Experimental Evaluation of Tensile Strength and Young s Modulus of Woven Jute fiber and Polyurethane Composite
More informationMECHANICAL PROPERTIES OF SURFACTANT-COATING CARBON NANOFIBER/EPOXY COMPOSITE
International Journal of Nanoscience, Vol. 1, Nos. 5 & 6 (2002) 1 6 c World Scientific Publishing Company MECHANICAL PROPERTIES OF SURFACTANT-COATING CARBON NANOFIBER/EPOXY COMPOSITE ZHE YING,, JIN-HONG
More informationINNOVATIVE HYBRID WEARING SURFACES FOR FRP BRIDGE DECKS
16 TH INTERNATIONAL CONFERENCE ON COMPOSITE MATERIALS INNOVATIVE HYBRID WEARING SURFACES FOR FRP BRIDGE DECKS Riyad S. Aboutaha Syracuse University Keywords: FRP decks, bridge decks, wearing surfaces Abstract
More informationEnhanced Durability of One-Part Polyurethane Bonds to Wood Due to the Use of HMR Primer
Enhanced Durability of One-Part Polyurethane Bonds to Wood Due to the Use of HMR Primer Alfred W. Christiansen Chemical Engineer Charles B. Vick Research Scientist E. Arnold Okkonen Physical Science Technician,
More informationProcessing of expanded graphite reinforced polymer nanocomposites
Composites Science and Technology 66 (26) 1179 1186 COMPOSITES SCIENCE AND TECHNOLOGY www.elsevier.com/locate/compscitech Processing of expanded graphite reinforced polymer nanocomposites Asma Yasmin,
More information1E5 Advanced design of glass structures. Martina Eliášová
1E5 Advanced design of glass structures Martina Eliášová List of lessons 1) History, chemical, production 2) Glass as a material for load bearing structures 3) Design of laminated plates 4) Design of glass
More informationMECHANICAL AND THERMAL PROPERTIES OF CARBON/EPOXY NANOCLAY COMPOSITES EXPOSED TO SYNERGISTIC EFFECT OF UV RADIATION AND CONDENSATION
18 TH INTERNATIONAL CONFERENCE ON COMPOSITE MATERIALS MECHANICAL AND THERMAL PROPERTIES OF CARBON/EPOXY NANOCLAY COMPOSITES EXPOSED TO SYNERGISTIC EFFECT OF UV RADIATION AND CONDENSATION A. Tcherbi-Narteh,
More informationComposites: Part B 42 (2011) Contents lists available at ScienceDirect. Composites: Part B
Composites: Part B 42 (2011) 1708 1712 Contents lists available at ScienceDirect Composites: Part B journal homepage: www.elsevier.com/locate/compositesb Mechanism of reinforcement in a nanoclay/polymer
More informationCarbon-fiber Reinforced Concrete with Short Aramid-fiber Interfacial Toughening
2016 International Conference on Electronic Information Technology and Intellectualization (ICEITI 2016) ISBN: 978-1-60595-364-9 Carbon-fiber Reinforced Concrete with Short Aramid-fiber Interfacial Toughening
More informationEPIKOTE Resin MGS BPR 435 EPIKURE Curing Agent MGS BPH
Product Bulletin Wind Energy Industrial bonding paste with outstanding fatigue performance EPIKOTE Resin MGS BPR 435 EPIKURE Curing Agent MGS BPH 434 439 The EPIKOTE Resin MGS BPR 435 system series was
More informationMEASUREMENT OF THE MECHANICAL PROPERTIES OF A CARBON REINFORCED BISMALEIMIDE OVER A WIDE RANGE OF TEMPERATURES
Revista da Associação Portuguesa de Análise Experimental de Tensões ISSN 66-778 MEASUREMENT OF THE MECHANICAL PROPERTIES OF A CARBON REINFORCED BISMALEIMIDE OVER A WIDE RANGE OF TEMPERATURES L. F. M. da
More informationNEW HYBRID GLULAM BEAM REINFORCED WITH CFRP AND ULTRA-HIGH-PERFORMANCE CONCRETE
NEW HYBRID GLULAM BEAM REINFORCED WITH CFRP AND ULTRA-HIGH-PERFORMANCE CONCRETE L. MICHEL Associate Professor Université Lyon 1-INSA LYON 1 82 bd Niels Bohr 69622 VILLEURBANNE Emmanuel.ferrier@univ-lyon1.fr
More informationCold-curing epoxy system based on Araldite LY 564 / Hardener HY 560
Ciba Specialty Chemicals Performance Polymers Structural Composites MATRIX SYSTEMS FOR AEROSPACE COMPOSITES MATRIX SYSTEMS FOR INDUSTRIAL COMPOSITES DATA SHEET Cold-curing epoxy system based on Araldite
More informationAssessment process of a new structural PUR adhesive
Assessment process of a new structural PUR adhesive Mario Marra 1, Martino Negri 2, Stefano Guercini 3 and Ario Ceccotti 4 ABSTRACT: Engineered timber-based elements used nowadays in timber buildings are
More informationReinforcement of glulam beams with FRP reinforcement
Reinforcement of glulam beams with FRP reinforcement H.J. Blaß and M. Romani University of Karlsruhe (TH), Germany 1 Introduction For several years possibilities to reinforce glulam beams parallel to the
More informationFlexural Behaviour of Sandwich Composite Panels Fabricated Through Different Vacuum Bagging Techniques
Journal of Materials Science & Surface Engineering Vol. 3 (4), 2015, pp 293-297 Contents lists available at http://www.jmsse.org/ Journal of Materials Science & Surface Engineering Flexural Behaviour of
More informationPractice Problems Set # 3 MECH 321 Winter 2018
Question 1 Copper-rich copper beryllium alloys are precipitation hardenable. After consulting the portion of the phase diagram given below, answer the following questions: (a) Specify the range of compositions
More informationFRACTURE TOUGHNESS EVALUATION OF COMPOSITE/METAL ADHESIVE STRUCTURE IN CRYOGENIC ENVIRONMENT
16 TH INTERNATIONAL CONFERENCE ON COMPOSITE MATERIALS FRACTURE TOUGHNESS EVALUATION OF COMPOSITE/METAL ADHESIVE STRUCTURE IN CRYOGENIC ENVIRONMENT Ryohei Maruyama*, Tomohiro Yokozeki **, Toshio Ogasawara***,
More informationDEVELOPMENT AND EVALUATION OF FRACTURE MECHANICS TEST METHODS FOR SANDWICH COMPOSITES
DEVELOPMENT AND EVALUATION OF FRACTURE MECHANICS TEST METHODS FOR SANDWICH COMPOSITES Daniel O. Adams, Jeffery A. Kessler, Joseph Nelson, Josh Bluth, and Brad Kuramoto Department of Mechanical Engineering
More informationApplication of the modified split-cantilever beam for mode-iii toughness measurement
Fourth International Conference on FRP Composites in Civil Engineering (CICE008) -4July 008, Zurich, Switzerland Application of the modified split-cantilever beam for mode-iii toughness measurement A.
More informationMechanical performance of bacterial cellulose nanofibre-reinforced epoxy composites
High Performance Structure and Materials VI 379 Mechanical performance of bacterial cellulose nanofibre-reinforced epoxy composites H. Takagi1, A. N. Nakagaito1 & K. Uchida2 1 2 Institute of Technology
More informationANCHORING METHOD FOR PRESTRESSING OF FRP REINFORCEMENT
ANCHORING METHOD FOR PRESTRESSING OF FRP REINFORCEMENT D Ďurech, Brno University of Technology, Czech Republic F Girgle, Brno University of Technology, Czech Republic D Horák, Brno University of Technology,
More informationSTRENGTH DISTRIBUTION COMPARISON OF AEROSPACE AND WIND ENERGY CARBON FIBER REINFORCED EPOXY. Eric M. Jensen*, Ray S. Fertig III*
International Conference on Future Technologies for Wind Energy October 07-09, 2013, Laramie, Wyoming, USA STRENGTH DISTRIBUTION COMPARISON OF AEROSPACE AND WIND ENERGY CARBON FIBER REINFORCED EPOXY Eric
More informationScotch-Weld Metal Bonder Acrylic Adhesive DP8407NS Gray
Scotch-Weld Metal Bonder Acrylic Adhesive Preliminary Technical Data Sheet October 2017 Product Description is a high performance, two-part acrylic adhesive that offers excellent shear, peel, and impact
More informationSTRENGTH AND DURABILITY OF ONE-PART POLYURETHANE ADHESIVE BONDS TO WOOD
PROCESSES STRENGTH AND DURABILITY OF ONE-PART POLYURETHANE ADHESIVE BONDS TO WOOD CHARLES B. VICK E. ARNOLD OKKONEN ABSTRACT One-part polyurethane wood adhesives comprise a new class of general purpose
More informationMECHANICAL CHARACTERIZATION OF SANDWICH STRUCTURE COMPRISED OF GLASS FIBER REINFORCED CORE: PART 1
Composites in Construction 2005 Third International Conference Lyon, France, July 11 13, 2005 MECHANICAL CHARACTERIZATION OF SANDWICH STRCTRE COMPRISED OF GLASS FIBER REINFORCED CORE: PART 1 S.V. Rocca
More informationProduct Data Sheet Sikadur -31 CF Normal Product Description Uses ruction Const Characteristics / Advantages
Construction Product Data Sheet Edition 02/12/2013 Identification no: 02 04 02 03 001 0 000039 Sikadur -31 CF Normal 2-part thixotropic epoxy adhesive Product Description Uses Characteristics / Advantages
More informationPB 250, PB 400 / SD 560x Resilient & ambient curing epoxy foam
PB 250, PB 400 / Resilient & ambient curing epoxy foam Page 1 / 5 PB products are 2 component epoxy foaming formulations developed for in situ low density epoxy foam production. Foam final density is depends
More informationPOLYMER MODIFIED CEMENTITIOUS SYSTEMS
POLYMER MODIFIED CEMENTITIOUS SYSTEMS Odile Quet 13.9.2005 WHY TO USE A CEMENT MODIFIER? Concrete Wev Repair mortars, renders, ceramic tile adhesives.. Wev S, V, W/C Thickness: Drop in w/c Drop on properties
More informationDIVISION 9 FINISHES Section Floor Finishes
Spec Component: SC-032-0807 Supersedes: SS-032-0601 DIVISION 9 FINISHES Section 09600 Floor Finishes Part 1 - General 1.01 Summary A. This specification describes the application of a waterproofing, slip
More informationTests on FRP-Concrete Bond Behaviour in the presence of Steel
Tests on FRP-Concrete Bond Behaviour in the presence of Steel M. Taher Khorramabadi and C.J. Burgoyne Engineering Department, University of Cambridge Trumpington St., Cambridge, UK ABSTRACT The bond behaviour
More informationJoining of Dissimilar Automotive Materials
Joining of Dissimilar Automotive Materials P.K. Mallick William E. Stirton Professor of Mechanical Engineering Director, Center for Lighweighting Automotive Materials and Processing University of Michigan-Dearborn
More informationFracture Toughness and Mechanical Properties of Aluminum Oxide Filled Chopped Strand Mat E-Glass Fiber Reinforced Epoxy Composites
International Journal of Scientific and Research Publications, Volume 4, Issue 7, July 2014 1 Fracture Toughness and Mechanical Properties of Aluminum Oxide Filled Chopped Strand Mat E-Glass Fiber Reinforced
More information3-Part Epoxy Grouting System for Pile Capping
Product Data Sheet Edition: 10/10/2012 Identification no. Version no: GCC Sikadur -42 PC Sikadur -42 PC 3-Part Epoxy Grouting System for Pile Capping Product Description Uses Characteristics / Advantages
More informationENGINEERING MATERIAL 100
Department of Applied Chemistry Division of Science and Engineering SCHOOL OF ENGINEERING ENGINEERING MATERIAL 100 Experiments 4 and 6 Mechanical Testing and Applications of Non-Metals Name: Yasmin Ousam
More informationG.B.M. building equipments PONTEGGI. Parapetti Certifi cati SHUTTERING PANELS AND FORMWORK H20 BEAMS
Parapetti Certifi cati d ng equip SHUTTERING PANELS AND FORMWORK H0 BEAMS shuttering panels are high-quality, -ply wooden panels, made of spruce and fir wood acquired from sustainable forests. The panels
More informationProgress report Material characterization and impact performance of Semi Impregnated Micro-Sandwich structures, SIMS
Progress report Material characterization and impact performance of Semi Impregnated Micro-Sandwich structures, SIMS Dipartimento di Ingegneria Meccanica e Aerospaziale By. Prof. G. Belingardi, Alem.T.
More informationFIVE STAR PRODUCTS, INC. (800)
FIVE STAR PRODUCTS, INC. www.fivestarproducts.com (800) 243-2206 Page 1 of 11 DESIGN-A-SPEC GUIDELINES FIVE STAR RS ANCHOR GEL CONTENTS PART A - GENERAL CONDITIONS PART B - MATERIAL SPECIFICATIONS PART
More informationComparison of Energy Absorption Characteristics of Thermoplastic Composites, Steel and Aluminum in High-Speed Crush Testing of U-Beams
Comparison of Energy Absorption Characteristics of Thermoplastic Composites, Steel and Aluminum in High-Speed Crush Testing of U-Beams CELANESE ENGINEERED MATERIALS Michael Ruby October, 2013 1 Overview
More informationEFFECT OF CARBON NANOTUBE DISPERSION ON THE FRACTURE TOUGHNESS OF POLYMERS
EFFECT OF CARBON NANOTUBE DISPERSION ON THE FRACTURE TOUGHNESS OF POLYMERS V. Mirjalili, P. Hubert Department of Mechanical Engineering, McGill University 817 Sherbrooke Street West, Montreal, Quebec H3A
More informationMECHANICAL PROPERTISE OF KENAF FIBER COMPOSITE USING CO- CURED IN-LINE FIBER JOINT
MECHANICAL PROPERTISE OF KENAF FIBER COMPOSITE USING CO- CURED IN-LINE FIBER JOINT Ribot, N.M.H., Ahmad, Z.*, Mustaffa, N.K. Faculty of Civil Engineering, Universiti Teknologi MARA Malaysia, 40450,Shah
More informationAraldite LY 5052 Resin / Aradur 5052 Hardener
Araldite LY 5052 Resin / Aradur 5052 Hardener Product Description Araldite LY 5052 is a low-viscosity epoxy resin that is used with Aradur 5052, a mixture of polyamines, to form a cold curing epoxy system.
More informationSikadur -330 is a two part, thixotropic epoxy based impregnating resin / adhesive.
Product Data Sheet Edition 21/02/2012 Identification no: 02 04 01 04 001 0 000004 2-part epoxy impregnation resin Construction Product Description is a two part, thixotropic epoxy based impregnating resin
More informationStudies on ductility of RC beams in flexure and size effect
Studies on ductility of RC beams in flexure and size effect G. Appa Rao* & I. Vijayanand *University of Stuttgart, 7569, Stuttgart, Germany Indian Institute of Technology Madras, Chennai-6 36, India R.
More informationStainless Steel & Stainless Steel Fasteners Chemical, Physical and Mechanical Properties
Stainless Steel & Stainless Steel Fasteners Chemical, Physical and Mechanical Properties Stainless steel describes a family of steels highly resistant to tarnishing and rusting that contain at least two
More informationTensile Bond Between Substrate Concrete and Normal Repairing Mortar under Freeze Thaw Cycles
4 th International Conference on the Durability of Concrete Structures 24 26 July 2014 Purdue University, West Lafayette, IN, USA Abstract Tensile Bond Between Substrate Concrete and Normal Repairing Mortar
More informationMECHANICAL PROPERTIES OF TRIAXIAL BRAIDED CARBON/EPOXY COMPOSITES
MECHANICAL PROPERTIES OF TRIAXIAL BRAIDED CARBON/EPOXY COMPOSITES C. L. Bowman 1, G. D. Roberts 1, M. S. Braley 2, M. Xie 3 & M. J. Booker 4 1 NASA Glenn Research Center, Cleveland OH 44135 2 A&P Technology,
More informationTesting of Bond Coat Emulsions
National Pavement Preservation Conference Nashville, TN Testing of Bond Coat Emulsions August, 2012 Arlis Kadrmas BASF Corporation 1 Testing of Tack/Bond Emulsions Presentation Outline Definition of a
More informationPart 4 MECHANICAL PROPERTIES
Part 4 MECHANICAL PROPERTIES Fiber Composite Materials M. S. Ahmadi 192 TENSILE PROPERTIES Tensile properties, such as tensile strength, tensile modulus, and Poisson s ratio of flat composite laminates,
More informationShort Jute Fiber-Reinforced Polypropylene Composites: Effect of Compatibilizer
Short Jute Fiber-Reinforced Polypropylene Composites: Effect of Compatibilizer A. K. RANA, 1 A. MANDAL, 1 B.C. MITRA, 1 R. JACOBSON, 2 R. ROWELL, 2 A. N. BANERJEE 3 1 Indian Jute Industries' Research Association,
More informationTESTING AND MODELLING OF PRESTRESSED TIMBER BEAMS USING A MULTI SURFACE PLASTICITY MODEL
TESTING AND MODELLING OF PRESTRESSED TIMBER BEAMS USING A MULTI SURFACE PLASTICITY MODEL Martin Lehmann 1, Till Vallée 2, Karl Rautenstrauch 3 ABSTRACT: The refurbishment of old buildings often comes hand
More informationModule 8: Composite Testing Lecture 36: Quality Assessment and Physical Properties. Introduction. The Lecture Contains
Introduction In the previous lecture we have introduced the needs, background and societies for mechanical testing of composites. In this lecture and subsequent lectures we will see principles for the
More informationFunctional enhancement of epoxy polymer nanocomposite: A nano blended binder for retrofitting of bridges
Functional enhancement of epoxy polymer nanocomposite: A nano blended binder for retrofitting of bridges B. Bhuvaneshwari 1, Saravana Karthikeyan 1, G.S. Palani 1 and Nagesh R. Iyer 1 1 (CSIR- Structural
More informationISO INTERNATIONAL STANDARD. Wood-based panels Oriented strand board (OSB) Definitions, classification and specifications
INTERNATIONAL STANDARD ISO 16894 First edition 2009-11-15 Wood-based panels Oriented strand board (OSB) Definitions, classification and specifications Panneaux à base de bois Panneaux de lamelles minces,
More informationJoining & Bonding of Composite Parts The Structural Adhesive Advantage
Joining & Bonding of Composite Parts The Structural Adhesive Advantage Recent trends and advancements in the manufacturing and cost reduction of composite materials has increased their usage in the transportation,
More informationDesign Methods of Elements from Cross-Laminated Timber Subjected to Flexure
RIGA TECHNICAL UNIVERSITY INSTITUTE OF STRUCTURAL ENGINEERING AND RECONSTRUCTION A.Vilguts, D.Serdjuks, L.Pakrastins Design Methods of Elements from Cross-Laminated Timber Subjected to Flexure RIGA 2015
More informationPolymer Linings for Restoration & Corrosion Protection of Steel Surfaces: Crude Oil Storage Tank Repair and Reline in New Zealand
Polymer Linings for Restoration & Corrosion Protection of Steel Surfaces: Crude Oil Storage Tank Repair and Reline in New Zealand ~ 2009 SSPC Corrosion Conference ~ By: Greg Severyn, Sauereisen Inc., Greg
More informationInnovative Application of Scrap-tire Steel Cords in Concrete Mixes
Innovative Application of Scrap-tire Steel Cords in Concrete Mixes Ahmed N. Bdour 1) and Yahia A. Al-Khalayleh 2) 1) Assistant Professor and Assistant Dean of Engineering College, Department of Civil Engineering,
More informationConstruction. Adhesive for bonding Carbon Fibre & Steel reinforcement. Product Description. Tests
Product Data Sheet Edition 10/12/2014 Identification no: 02 04 01 04 001 0 000001 Sikadur -30 Adhesive for bonding Carbon Fibre & Steel reinforcement Construction Product Description Uses Characteristics
More informationBehavior and Strength of Bearing Wall Strengthening by CFRP
Behavior and Strength of Bearing Wall Strengthening by CFRP Amer M. Ibrahim, Wissam D. Salman Prof. Dr., College of Engineering, Lect. Dr., College of Engineering, Diyala University, Iraq Abstract Collapse
More informationFeatures Conductive Room Temperature Cure. Product Ref IP 4525IP Low viscosity adhesive & coating. High thermal conductivity
Properties and Part Selection Overview Selection Table - Epoxy-Based Adhesive Properties Features Conductive Room Temperature Cure Product Ref 120 132 4461IP 42IP 438 700 Properties High electrical conductivity
More information3 Scotch-Weld TM. Structural Adhesive Film AF 563. Technical Data September, 2002
3 Scotch-Weld TM Technical Data September, 2002 Introduction 3M Scotch-Weld designates a family of moderate cure temperature thermosetting structural adhesive films. Scotch-Weld is similar to 3M Scotch-Weld
More informationDURABILITY OF ONE-PART POLYURETHANE BONDS TO WOOD IMPROVED BY HMR COUPLING AGENT
PROCESSES DURABILITY OF ONE-PART POLYURETHANE BONDS TO WOOD IMPROVED BY HMR COUPLING AGENT CHARLES B. VICK E. ARNOLD OKKONEN ABSTRACT In a previous study on the strength and durability of a new class of
More informationTHE INFLUENCE OF THE AMOUNT OF FIBRE REINFORCEMENT ON THE AIR PERMEABILITY OF HIGH PERFORMANCE CONCRETE
2009/2 PAGES 1 7 RECEIVED 10. 1. 2009 ACCEPTED 9. 4. 2009 P. PAULÍK, I. HUDOBA THE INFLUENCE OF THE AMOUNT OF FIBRE REINFORCEMENT ON THE AIR PERMEABILITY OF HIGH PERFORMANCE CONCRETE ABSTRACT Peter Paulík
More informationIntroduction to Engineering Materials ENGR2000 Chapter 8: Failure. Dr. Coates
Introduction to Engineering Materials ENGR2000 Chapter 8: Failure Dr. Coates Canopy fracture related to corrosion of the Al alloy used as a skin material. 8.2 Fundamentals of Fracture Fracture is the separation
More informationEPOXY RESIN SYSTEMS FOR HIGH PERFORMANCE FRP
EPOXY RESIN SYSTEMS FOR HIGH PERFORMANCE FRP MOULDS Dr Mahesh Soni * GM Research & Development - Polymers / Atul Ltd mahesh_soni@atul.co.in Dr Utkarsh Shukla Manager Research & Development - Polymers /
More informationCHARACTERIZATION OF PHYSICAL AND MECHANICAL PROPERTIES OF RIGID POLYURETHANE FOAM
CHARACTERIZATION OF PHYSICAL AND MECHANICAL PROPERTIES OF RIGID POLYURETHANE FOAM Puput Wiyono, Faimun, Priyo Suprobo and Heppy Kristijanto Department of Civil Engineering, Institut Teknologi Sepuluh Nopember,
More informationDEVELOPMENT OF THERMOPLASTIC RESIN IMPREGNATED YARN AND ITS COMPOSITE PROPERTIES
DEVELOPMENT OF THERMOPLASTIC RESIN IMPREGNATED YARN AND ITS COMPOSITE PROPERTIES Akio Ohtani 1, Mitsuro Takagi 2, Jun Takashima 3, Kouji Nakajima 4, Takayuki Imai 4, Tadashi Uozumi 1, Asami Nakai 1, Hiroyuki
More informationCFRP STRENGTHENING OF CONCRETE BRIDGES WITH CURVED SOFFITS
CFRP STRENGTHENING OF CONCRETE BRIDGES WITH CURVED SOFFITS Nagaraj Eshwar Dr Tim Ibell Dr Antonio Nanni Graduate Research Assistant Senior Lecturer Jones Professor CIES, # 223 ERL University of Bath CIES,
More informationEvaluation Listing CCMC L Nordic X-Lam
CONSTRUCTION Evaluation Listing CCMC 3654-L Nordic X-Lam Evaluation Issued: 203-2-24 Re-evaluation due: 206-2-24 Preface: Masterformat 06 9 00.02, Cross Laminated Timber (CLT) Panels (Standardized) Preface
More informationINNOVATIVE FIBRE REINFORCED BRIDGE DECK MODULES ABSTRACT
INNOVATIVE FIBRE REINFORCED BRIDGE DECK MODULES Heather Crocker, ISIS Canada, Winnipeg, MB Emile Shehata, Wardrop Engineering Inc., Winnipeg, MB Rick Haldane-Wilsone, Wardrop Engineering Inc., Winnipeg,
More informationEvaluation of Curing Process for Kevlar 49-Epoxy Composites by Mechanical Characterization Designed for Brake Liners
Evaluation of Curing Process for Kevlar 49-Epoxy Composites by Mechanical Characterization Designed for Brake Liners A. Chennakesava Reddy Professor, Department of Mechanical Engineering, JNT University,
More informationTrue Stress and True Strain
True Stress and True Strain For engineering stress ( ) and engineering strain ( ), the original (gauge) dimensions of specimen are employed. However, length and cross-sectional area change in plastic region.
More informationFlexural Performance of Reinforced Concrete Beams with a Layer of Expansive Strain-hardening Cement -based Composite(SHCC)
Flexural Performance of Reinforced Concrete Beams with a Layer of Expansive Strain-hardening Cement -based Composite(SHCC) Hae Jun Yang, June Su Kim, Sung Ho Kim & Hyun Do Yun Chungnam National University,
More informationBonded Structures Industry Survey
Bonded Structures Industry Survey Bonded John Tomblin Wichita State University / NAIR Wichita, KS and Curtis Davies FAA Technical Center Atlantic City International Airport, NJ Survey Motivation Bonding
More informationTrusted ICC ES. Conformity! Look. Evaluation. ICC-ES Evaluation
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.orgg ESR 3288 Reissued 12/2017 This report is subject to renewal 12/2018. DIVISION: 03 00
More informationcarbon Abstract: 1. Introduction produce the toughness of Nanotubes Elasticity India in a 36- in the tensile strength showed Single-walled
World Journal of Nano Science and Engineering, 2011, 1, ** doi: 10.4236/wjnse.2011.110011 Published Online March 20111 (http://www.scirp.org/journal/wjnse) Enhancement of Elastic Modulus of Epoxy Resin
More informationMechanical Characterisation of Polyamide 66/Graphite Nanocomposites
International Journal of Materials Science ISSN 0973-4589 Volume 12, Number 3 (2017), pp. 411-420 Research India Publications http://www.ripublication.com Mechanical Characterisation of Polyamide 66/Graphite
More informationEFFECT OF VOLUME FRACTION EPOXY-HOLLOW GLASS MICROSPHERES AND CURING TEMPERATURE VARIATION ON COMPRESSIVE PROPERTIES OF COMPOSITES
EFFECT OF VOLUME FRACTION EPOXY-HOLLOW GLASS MICROSPHERES AND CURING TEMPERATURE VARIATION ON COMPRESSIVE PROPERTIES OF COMPOSITES Sutikno, Wajan Berata, Wahyu Wijanarko and Indra Sidharta Mechanical Engineering
More informationAsk for FSC certified products. Ask for PEFC certified products.
Ask for FSC certified products. Ask for PEFC certified products. ABOUT COMPANY Mission - provide solutions to enhance customers product value. Vision - to be a leader among wood based panel producers in
More informationLASER SURFACE PREPARATION AND BONDING OF AEROSPACE STRUCTURAL COMPOSITES
LASER SURFACE PREPARATION AND BONDING OF AEROSPACE STRUCTURAL COMPOSITES M.A. Belcher, 1 C.J. Wohl, 1 and J.W. Connell 2 1 National Institute of Aerospace, 100 Exploration Way, Hampton, VA 23666, USA 2
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 WESTMORELAND MECHANICAL TESTING & RESEARCH, INC. 1 221 Westmoreland Drive Youngstown, PA 15696 Michael Self Phone: 724 537 3131 E-mail: mself@wmtr.com MECHANICAL
More informationGage Series Stress Analysis Gages
GAGE SERIES All Micro-Measurements strain gages incorporate precision foil grids mounted on organic backing materials. The strain-sensing alloys and backing materials cannot be arbitrarily combined in
More informationProgress on cellulose nanofiberfilled thermoplastic composites
Progress on cellulose nanofiberfilled thermoplastic composites Douglas J. Gardner, Yousoo Han, Alper Kiziltas, and Yucheng Peng Session 5: The role of nanotechnology in green materials and sustainable
More informationBonding of Carbon Fibre-reinforced Plastics with Wood
Bonding of Carbon Fibre-reinforced Plastics with Wood René STEIGER Dr. sc. techn. / civil engineer Swiss Federal Laboratories for Materials Testing and Research EMPA Wood Laboratory Dübendorf, Switzerland
More informationThe effect of Nano-fibrillated cellulose on the mechanical properties of polymer films.
The effect of Nano-fibrillated cellulose on the mechanical properties of polymer films. Gerard Gagnon, Rikard Rigdal, Jake Schual-Berke, Mike Bilodeau and Douglas W. Bousfield Department of Chemical and
More informationEffect of Bar-cutoff and Bent-point Locations on Debonding Loads in RC Beams Strengthened with CFRP Plates
CICE 2010 - The 5th International Conference on FRP Composites in Civil Engineering September 27-29, 2010 Beijing, China Effect of Bar-cutoff and Bent-point Locations on Debonding Loads in RC Beams Strengthened
More informationEffects of Steel and Polypropylene Fiber Addition on Interface Bond Strength between Normal Concrete Substrate and Self-Compacting Concrete Topping Slamet Widodo Doctoral Student at Department of Civil
More information2. Definition of Environmental Stress Cracking (ESC)
2. Definition of Environmental Stress Cracking (ESC) Environmental stress cracking (ESC) in plastics means the failure at about room temperature due to continuously acting external and/or internal stresses
More informationThree-Dimensional Material Properties of Composites with S2-Glass Fibers or Ductile Hybrid Fabric
: Distribution Statement A. Approved for public release. Three-Dimensional Material Properties of Composites with S2-Glass Fibers or Ductile Hybrid Fabric Keith J. Kowalkowski, Nabil F. Grace Lawrence
More informationFiber Reinforced Tile and Stone Mortar
, ANSI A 118.4, ANSI A 118.11 ARDEX X 77 MICROTEC Fiber Reinforced Tile and Stone Mortar The most advanced technology ideal for large format porcelain tile installations,exterior or interior, floor or
More informationExperimental Evaluation And Analysis Of Glass Fiber Reinforced Composite Under Mechanical Loading
Original Paper Volume 2 Issue 11 July 2015 International Journal of Informative & Futuristic Research ISSN (Online): 2347-1697 Experimental Evaluation And Analysis Of Glass Fiber Reinforced Composite Under
More informationGLT GIRDER LONGITUDINALLY TENSILETESTED
GLT GIRDER LONGITUDINALLY TENSILETESTED THE INDIVIDUALLY TESTED SAFETY GUARANTOR. 01 AT A GLANCE AREAS OF APPLICATION Construction and industrial buildings Multi-storey residential buildings Single and
More informationEffect of PEK Content on Fracture Toughness of Glass Woven Fabric / Phenolic Resin Composites
Effect of PEK Content on Fracture Toughness of Glass Woven Fabric / Phenolic Resin Composites Y.Q. Sun 1,2, J.H. Li, 2 J.B. Wang, 2 S.R. Zheng 3 and M.L. Sun 3 1 Laboratory for Nonlinear Mechanics of Continuous
More information