Applications. - APS coatings -

Size: px
Start display at page:

Download "Applications. - APS coatings -"

Transcription

1 Applications - APS coatings - Applications of APS coatings Typical spray materials Oxide ceramics: Cr 2 O 3, Al 2 O 3, Al 2 O 3 /TiO 2 Compounds: Ni/C G, AlSi/Polyester, [WC/Co(Cr), Cr 3 C 2 /NiCr] Metals: Mo, NiCrBSi, CoCrWC, CoCrMoSi, CuAl(Fe), CuNi(In) Aim for surfaces of components build of cheap base materials or base materials that fufill structural demands (strength, formability) in an optimal way Partially in combination with corrosion protection Partially in combination with special surface properties like high or low wettability by different media Abradable coatings for clearance control Coatings with tribological function 1

2 Printing machines Ink ductor rollers in offset printing machines High resistance against wear by pigments in ink Ink is easily both picked up and transferred after adequate coating finishing APS sprayed Cr 2 O 3 APS sprayed Ni5Al bond coat Terolab Services König & Bauer Coatings with tribological function Printing machines Anilox rollers in flexo printing machines APS sprayed high purity Cr 2 O 3 (laser engraved) High wear resistance of small webs, easy ink take-up and cleaning Only metal free coatings permit homogeneous laser engraving and therefore suitable quality König & Bauer Coatings with tribological function 2

3 Printing machines Anilox rollers SOT, Salzgitter Coatings with tribological function Cooking pans APS Al 2 O 3 layer as wear resistant support for anti-sticking coating layer compound Easy cleaning of light-weight cast aluminum alloy pans 3

4 Textile industries Grooved rollers, godets, templates for guidance of fibres APS Al 2 O 3 /TiO 2 Depending on the specific demands coating surfaces need to be smoothened by brushing, grinding and / or polishing to avoid fibre damage Terolab Services Seals Seal rings with high wear resistance and low friction APS Cr 2 O 3 Post-treatment by polishing Related applications: - pump shafts - protective bushings Terolab Services 4

5 Piston rings APS Mo/NiCrBSi and coatings including molybdenum carbide compete against Al 2 O 3 or diamond impregnated hard chromium or PVD coating solutions Piston rings APS Mo/NiCrBSi coating Microhardness: ~ 500 HV0.3 Coating porosity has tribologoical function because of storage of oil in lubricating pockets 5

6 Hydraulic pistons APS Cr 2 O 3 /TiO 2 on APS Ni5Al bond coat Suitable for off-shore applications after sealing Hunger Hydraulik Automotive in-line engines APS iron based coatings with Mo addition Iron oxides provide to some extent lubrication Coating porosity has tribologoical function becasuse of storage of oil in lubricating pockets Special production line at Volkswagen and prototype production for Formula 1 engines Chemnitz University of Technology Chemnitz University of Technology 6

7 Automotive in-line and V-engines PTWA and HVCW of plain steel wires Cooperation project with Daimler Chrysler, Ford, Gehring, General Motors and Porsche water blasted, coated, honed I, honed II coating substrate Doctor blades APS Al 2 O 3 /TiO 2 or Cr 2 O 3 coated blades improve lifetime compared to uncoated spring steel significantly 7

8 Turbine blade roots APS CuNiIn coatings for titanium compressor blade roots prevent adhesive wear Compressors (gas turbines) Abradable coatings greatly improve efficiency of axial flow compressors by minimizing air leaks APS Al 2 O 3 (more and more replaced by HVOF WC/Co) on the compressor rotor and APS or powder flame sprayed Ni/C G on the casing APS AlSi/Polyester coatings are alternative abradable coatings APS Al 2 O 3 for protection of labyrinth seal webs on rotors combined with soft counterbody surfaces APS Al 2 O 3 effectively limits titanium fire in gas turbines compressor section Clearance control 8

9 Gas turbine blades and vanes Hot gas corrosion protective MCrAlY (M := Ni,Co) coatings are the traditional major application of vacuum plasma spraying MCrAlY coatings form a protective alumina scale with excellent bond to the metallic base and yttria prevents grain growth and therefore detrimental effect on thermal shock resistance Institute of Materials Technology, Dortmund Hot gas corrosion protection Gas turbine blades and vanes APS YPSZ (partially stabilized zirconia, ZrO 2 /Y 2 O 3 ) thermal barrier coatings Combustion chambers with up to 4.5 m diameter and up to 3.5 t weight For aero engines aviation approval required Thermal insulation 9

10 Gas turbine blades and vanes APS ZrO 2 /Y 2 O 3 thermal barrier coatings on MCrAlY bond coats Institute of Materials Technology, Dortmund Thermal insulation Gas turbine blades and vanes APS ZrO 2 /Y 2 O 3 thermal barrier coatings on MCrAlY bond coats Improved life-time of turbine components due to lower thermal load of the core material Maximum component surface temperature: ~ 1250 C Despite intensive long-term research no improvement by alternative material solution achieved up to now Major problem: Sintering at service temperature results in decreased fracture toughness temperature thermal barrier coating bond coat substrate Thermal insulation 10

11 Electrical insulation APS Al 2 O 3 for electrical insulation α-phase is desired, because of high electrical resistance, but mostly γ-phase is produced during thermal spraying Moisture needs to be excluded in order to provide sufficient shielding effect of high-γ content Al 2 O 3 coatings dynamo components Electrical insulation Implants VPS cp Ti, Ti6Al4V and / or hydroxyapatite coated hip, knee and tooth implants Very high demands concerning coating purity Titanium (alloys) do not corrode in human tissue (biocompatible) and hydroxyapatite coatings can partially dissolve and provide bone growth during re-precipitation (bioactive) Terolab Services Biocompatible and -active coatings 11

12 Hardmagnetic NdFeB coatings VPS NdFeB to prevent oxidation which has detrimental effect on the magnetic properties Substrate temperature control needed for good magnetic properties Up to now only laboratory scale production Sensor and actuator coatings Hardmagnetic NdFeB coatings APS Al 2 O 3 -MgO (Spinell) or YPSZ coatings provide high oxygen ion diffusivity Current (produced by ion flux) at given temperature is a measure for oxygen content in exhaust gas Specific Bosch product replaced by alternative technology Lambda probe Sensor and actuator coatings 12

13 Target production for PVD processes (sputtering) Depending on the desired type of PVD coating and the size of targets different thermal spray processes can be applied For arc-pvd CrN coating production usually VPS of chromium is carried out, because chromium strongly oxidizes during spraying under atmospheric conditions VPS chromium sputter targets Institute of Materials Technology, Dortmund Material build-up Thank you for your attention! Thanks 13

GTV SPRAY POWDER CATALOGUE. according to DIN EN 1274

GTV SPRAY POWDER CATALOGUE. according to DIN EN 1274 according to DIN EN 1274 APPLICATION AREAS Overhaul / repair Wear protection Corrosion protection Bond coats Electrical isolation Thermal isolation Clearance control (Abradable Coatings) POWDER MORPHOLOGY

More information

Cutting Tool Materials and Cutting Fluids. Dr. Mohammad Abuhaiba

Cutting Tool Materials and Cutting Fluids. Dr. Mohammad Abuhaiba Cutting Tool Materials and Cutting Fluids HomeWork #2 22.37 obtain data on the thermal properties of various commonly used cutting fluids. Identify those which are basically effective coolants and those

More information

INTRODUCTION. Think HSS

INTRODUCTION. Think HSS INTRODUCTION Think HSS SUMMARY METALLURGY 2 Excellent strength 3 A super sharp edge 4 Safe and reliable tools Alloy elements 6 The influence of alloy elements 7 Standard compositions of HSS 8 The HSS-PM

More information

STUDIES ON THE APPLICABILITY OF THE HIGH VELOCITY THERMAL SPRAY USED IN THE AUTOMOTIVE INDUSTRY

STUDIES ON THE APPLICABILITY OF THE HIGH VELOCITY THERMAL SPRAY USED IN THE AUTOMOTIVE INDUSTRY STUDIES ON THE APPLICABILITY OF THE HIGH VELOCITY THERMAL SPRAY USED IN THE AUTOMOTIVE INDUSTRY D. PETRE 1 R. IOVANAŞ 1 A. PASCU 1 Abstract: The thermal spray is a domain connected to the welding process

More information

Thermal Surfacing Powder choice with ease

Thermal Surfacing Powder choice with ease Thermal Surfacing Powder choice with ease Why Thermal Surfacing Thermal surfacing is a cost effective method to achieve high performance characteristics on exposed metallic surfaces. A metal object can

More information

A REVIEW OF PROPERTIES, APPLICATIONS AND PRESENTLY STUDY DONE ON CERAMIC BEARINGS

A REVIEW OF PROPERTIES, APPLICATIONS AND PRESENTLY STUDY DONE ON CERAMIC BEARINGS Review Article ISSN 2278 0149 www.ijmerr.com Vol. 3, No. 3, July, 2014 2014 IJMERR. All Rights Reserved A REVIEW OF PROPERTIES, APPLICATIONS AND PRESENTLY STUDY DONE ON CERAMIC BEARINGS Simran Dutt Sharma

More information

Investigations on corrosion protective layers in waste incineration plants

Investigations on corrosion protective layers in waste incineration plants Investigations on corrosion protective layers in waste incineration plants Peter Crimmann, Dietmar Bendix, Martin Faulstich, Sulzbach-Rosenberg / D Corrosion in the hot gas area of waste incineration plants

More information

Cermet Materials (Recommend for HVOF spray process)

Cermet Materials (Recommend for HVOF spray process) Cermet Materials (Recommend for HVOF spray process) WC/12%Co Jun 2017 SURPREX WC12L WC/12%Co SURPREX WC12J SURPREX WC12D DTS-W171-75/32-75+32μm Hardness Abrasion resistance SURPREX WC12J DTS-W76-30/5 DTS-W522-45/15

More information

Machinability is the ease with which a given material may be worked with a cutting tool

Machinability is the ease with which a given material may be worked with a cutting tool Machinability Machinability is the ease with which a given material may be worked with a cutting tool Machinability ratings (MR) provide and understanding of the severity of a metalworking operation in

More information

PRIREV. ZI Vagos, lote

PRIREV. ZI Vagos, lote 2017 PRIREV We are the only Portuguese company that provides Decorative PVD services in several business areas. Our mission is make our partners more competitive in their markets with higher added value

More information

A SHORT NOTE ON MANUFACTURING PROCESS OF METAL POWDERS

A SHORT NOTE ON MANUFACTURING PROCESS OF METAL POWDERS INTERNATIONAL JOURNAL OF RESEARCH IN COMPUTER APPLICATIONS AND ROBOTICS ISSN 2320-7345 A SHORT NOTE ON MANUFACTURING PROCESS OF METAL POWDERS 1 R.Raja, 2 M.Rajkumar 1 Assistant Lecturer, St. Joseph College

More information

VDM Alloy 80 A Nicrofer 7520 Ti

VDM Alloy 80 A Nicrofer 7520 Ti VDM Alloy 80 A Nicrofer 7520 Ti Material Data Sheet No. 4048 February 2017 February 2017 VDM Alloy 80 A 2 VDM Alloy 80 A Nicrofer 7520 Ti VDM Alloy 80 A is a nickel-chromium alloy that can be age-hardened.

More information

AN INVESTIGATION OF THE THERMAL SHOCK BEHAVIOR OF THERMAL BARRIER COATINGS

AN INVESTIGATION OF THE THERMAL SHOCK BEHAVIOR OF THERMAL BARRIER COATINGS AN INVESTIGATION OF THE THERMAL SHOCK BEHAVIOR OF THERMAL BARRIER COATINGS ANDERSON.A Research scholar, Sathyabama University, Chennai, India. Email: anderson_ranji@yahoo.co.in, Phone: +91-9940223023 RAMACHANDRAN.S

More information

Turbine Tip Clearance Issues and Optimization for Increased Power and Efficiency. Lloyd Cooke Liburdi Turbine Services Inc

Turbine Tip Clearance Issues and Optimization for Increased Power and Efficiency. Lloyd Cooke Liburdi Turbine Services Inc Turbine Tip Clearance Issues and Optimization for Increased Power and Efficiency Lloyd Cooke Liburdi Turbine Services Inc www.liburdi.com Turbine Blade Tip Clearance Tip Clearance between Turbine Blades

More information

AMPERIT Thermal Spray Powders

AMPERIT Thermal Spray Powders Technology Metals Advanced Ceramics AMPERIT Thermal Spray Powders 2 H.C. Starck Expertise, Quality and Customer Awareness Whenever ideas are to be turned into successful products or applications, the first

More information

High-Entropy Alloys. Breakthrough Materials for Aero Engine Applications? By Daniel Svensson, Gothenburg, 13/2 2015

High-Entropy Alloys. Breakthrough Materials for Aero Engine Applications? By Daniel Svensson, Gothenburg, 13/2 2015 High-Entropy Alloys Breakthrough Materials for Aero Engine Applications? By Daniel Svensson, Gothenburg, 13/2 2015 Presentation Outline 1. 2. 3. 4. 5. 6. Introduction High-Entropy Alloys Aero Engine Materials

More information

MANUFACTURE AND REPAIR OF AERO ENGINE COMPONENTS USING LASER TECHNOLOGY (INVITED PAPER) Paper (405)

MANUFACTURE AND REPAIR OF AERO ENGINE COMPONENTS USING LASER TECHNOLOGY (INVITED PAPER) Paper (405) Proceedings of the 3 rd Pacific International Conference on Application of Lasers and Optics 2008 MANUFACTURE AND REPAIR OF AERO ENGINE COMPONENTS USING LASER TECHNOLOGY (INVITED PAPER) Paper (405) Ingomar

More information

LOW HEAT INPUT WELDING ALLOYS

LOW HEAT INPUT WELDING ALLOYS ASTRALOY 662 CHARACTERISTICS: An all position AC/DC electrode for high strength, crack free joining of low/medium carbon, and medium tensile steels of various compositions. Low alloy medium carbon steels,

More information

AEROSPACE THE SURFACE ENGINEERS

AEROSPACE THE SURFACE ENGINEERS AEROSPACE THE SURFACE ENGINEERS We are the leader in Aerospace coatings, you get the benefits Lower Cost and Environmental Impact Litres 5.0 4.5 4.0 4.52 4.39 4.10 3.98 3.94 3.85 3.85-14 % 3.88 The aerospace

More information

Stainless Steel & Stainless Steel Fasteners Chemical, Physical and Mechanical Properties

Stainless Steel & Stainless Steel Fasteners Chemical, Physical and Mechanical Properties Stainless Steel & Stainless Steel Fasteners Chemical, Physical and Mechanical Properties Stainless steel describes a family of steels highly resistant to tarnishing and rusting that contain at least two

More information

MANUFACTURING PROCESSES. Tool Material & Cutting Fluid

MANUFACTURING PROCESSES. Tool Material & Cutting Fluid MANUFACTURING PROCESSES Tool Material & Cutting Fluid 1 CUTTING TOOL MATERIAL Success in metal cutting depends on the selection of the proper cutting tool (material and geometry) for a given work material.

More information

Recent Technologies for Steam Turbines

Recent Technologies for Steam Turbines Recent Technologies for Steam Turbines Kenji Nakamura Takahiro Tabei Tetsu Takano A B S T R A C T In response to global environmental issues, higher efficiency and improved operational reliability are

More information

The most important parameters determining the performance of a cutting blade are:

The most important parameters determining the performance of a cutting blade are: Diamond blades exceptionally wear resistant and extremely sharp P. Gluche 1, S. Strobel 1, H.-J. Fecht 2 1 GFD Gesellschaft für Diamantprodukte mbh, Lise-Meitner-Str. 13, 89081 Ulm, Germany 2 University

More information

Tribology in Industry. PVD-Alumina Coatings on Cemented Carbide Cutting Tools: A Study About the Effect on Friction and Adhesion Mechanism

Tribology in Industry. PVD-Alumina Coatings on Cemented Carbide Cutting Tools: A Study About the Effect on Friction and Adhesion Mechanism Vol. 34, N o 1 (2012) 24-28 Tribology in Industry www.tribology.fink.rs RESEARCH PVD-Alumina Coatings on Cemented Carbide Cutting Tools: A Study About the Effect on Friction and Adhesion Mechanism S.E.

More information

Automotive & Mechanical Applications Broad Base. Best Solutions.

Automotive & Mechanical Applications Broad Base. Best Solutions. Carbon and Graphite Materials for Mechanical Seals Automotive & Mechanical Applications Broad Base. Best Solutions. Tribological Behavior Friction Friction depends on surface finish of the mating surfaces

More information

Supported by:

Supported by: 2012 Supported by: www.ubmaviationnews.com Advances in thermal barrier coatings Since gas turbine jet engines were developed more than 70 years ago they have made significant, continuous improvements today

More information

Increase powder packing density. Spherical particles provide denser packing of powders, increasing overall bulk tap density.

Increase powder packing density. Spherical particles provide denser packing of powders, increasing overall bulk tap density. Plasma power can make better powders It may be a truism to say that round powders pack better, but spheroidisation of powder particles is one of the successful commercial applications of induction plasma

More information

CUTTING TOOL TECHNOLOGY

CUTTING TOOL TECHNOLOGY CUTTING TOOL TECHNOLOGY Tool Life Tool Materials Tool Geometry Cutting Fluids Cutting Tool Technology Two principal aspects: 1. Tool material 2. Tool geometry Three Modes of Tool Failure Fracture failure

More information

WEAR PROPERTIES OF PLASMA NITRIDED INCONEL 718 SUPERALLOY

WEAR PROPERTIES OF PLASMA NITRIDED INCONEL 718 SUPERALLOY WEAR PROPERTIES OF PLASMA NITRIDED INCONEL 718 SUPERALLOY Halim Kovacı 1, Hojjat Ghahramanzadeh ASL 1, Çiğdem Albayrak 2, Akgün Alsaran 1 1 Ataturk University, Erzurum, Turkey 2 Erzincan University, Erzincan,

More information

Materials & Technology at Kennametal. Dev Banerjee VMA Conference March, 2012

Materials & Technology at Kennametal. Dev Banerjee VMA Conference March, 2012 Materials & Technology at Kennametal Dev Banerjee VMA Conference March, 2012 Contents Kennametal overview Materials portfolio Processing capabilities Basics of sintered carbide processing & properties

More information

Laser assisted Cold Spray

Laser assisted Cold Spray 2009-02-16 Laser assisted Cold Spray Andrew Cockburn, Matthew Bray, Rocco Lupoi Bill O Neill Innovative Manufacturing Research Centre (IMRC) Institute for Manufacturing, Department of Engineering, University

More information

Discover the variety of Metal Powders

Discover the variety of Metal Powders Discover the variety of Metal Powders The range of our standard metal powder Non Ferrous, Tool Steel, Stainless Steel and Light Alloys SLM The Industrial Manufacturing Revolution PIONEERS in metal-based

More information

Microstructural Studies of Thermal Spray Coating

Microstructural Studies of Thermal Spray Coating Microstructural Studies of Thermal Spray Coating Chennupati Vijaya Kumar SSIT, Sathupally-Khammam, India Subhash Kamal, PhD Universiti Teknologi Petronas, Malaysia ABSTRACT Chromium carbide nickel chrome,

More information

19 th SYMPOSIUM ON INDUSTRIAL APPLICATIONS OF GAS TURBINES

19 th SYMPOSIUM ON INDUSTRIAL APPLICATIONS OF GAS TURBINES 19 th SYMPOSIUM ON INDUSTRIAL APPLICATIONS OF GAS TURBINES Training Session 8: Gas Turbine Repair Technology by Scott Hastie / Liburdi Turbine Services Presented at the 19th Symposium on Industrial Application

More information

EQUIPMENT AND SYSTEM FOR VACUUM COATING METALLIZING, SPUTTERING, PLASMA and PECVD. Hybrid system KOLZER DGK 36

EQUIPMENT AND SYSTEM FOR VACUUM COATING METALLIZING, SPUTTERING, PLASMA and PECVD. Hybrid system KOLZER DGK 36 email : carlo.gennari@fastwebnet.it web site : http://carlogennariforni.beepworld.it/kolzer.htm EQUIPMENT AND SYSTEM FOR VACUUM COATING METALLIZING, SPUTTERING, PLASMA and PECVD Hybrid system KOLZER DGK

More information

HIGH TEMPERATURE CERAMIC & GRAPHITE ADHESIVES

HIGH TEMPERATURE CERAMIC & GRAPHITE ADHESIVES HIGH TEMPERATURE & GRAPHITE S Technical Bulletin A2 Ceramabond 835-M bonds halogen lamp. Ceramabond 503 coats heater used to 1700 ºC. Ceramabond 685-N bonds infrared heater. Graphi-Bond 551-RN bonds graphite

More information

Ceramic-metal Composite Coated Piston Ring and Cylinder Liner of Marine Low Speed Diesel Engine*

Ceramic-metal Composite Coated Piston Ring and Cylinder Liner of Marine Low Speed Diesel Engine* 77 Ceramic-metal Composite Coated Piston Ring and Cylinder Liner of Marine Low Speed Diesel Engine* Masaki Tanaka * *, Yoshihisa Kitajima * *, Yasuhisa Endoh * *, Masaoki Watanabe * *, Yutaka Nagita *

More information

GRINDING AND OTHER ABRASIVE PROCESSES

GRINDING AND OTHER ABRASIVE PROCESSES GRINDING AND OTHER ABRASIVE PROCESSES Grinding Related Abrasive Process Abrasive Machining Material removal by action of hard, abrasive particles usually in the form of a bonded wheel Generally used as

More information

Heat Treating Basics-Steels

Heat Treating Basics-Steels Heat Treating Basics-Steels Semih Genculu, P.E. Steel is the most important engineering material as it combines strength, ease of fabrication, and a wide range of properties along with relatively low cost.

More information

Ceramic materials with submicron structure based on nanopowders

Ceramic materials with submicron structure based on nanopowders Ceramic materials with submicron structure based on nanopowders Uwe Reichel, Fraunhofer Institute for Ceramic Technologies and Systems IKTS Institutsteil Hermsdorf, D-07629 Hermsdorf, Germany Nanophotonics

More information

Fabrication of Magnesium Oxide Ceramics with Density Close to Theoretical Using Nanopowders

Fabrication of Magnesium Oxide Ceramics with Density Close to Theoretical Using Nanopowders Fabrication of Magnesium Oxide Ceramics with Density Close to Theoretical Using Nanopowders Jing Yang, Tzu-Chieh Lin, Bill Manett, Jeremy Young, Dan Rooney Eugene Medvedovski SCI Engineered Materials,

More information

Typical aerospace-standard materials

Typical aerospace-standard materials JOHANN MAIER GmbH & Co. KG Schockenriedstraße 3 70565 Stuttgart-Vaihingen Typical aerospace-standard materials 1.4314.7 Stainless, austenitic steel 0,05C-1Cr-Ni X5 CrNi 1 1.4301 / AISI 304 60 * * Special

More information

Toughness measurement of Thermal Barrier Coatings (TBCs)

Toughness measurement of Thermal Barrier Coatings (TBCs) Class: Master Project of Engineering Science Advisor # 1: Professor Ernesto Gutierrez-Miravete Advisor # 2: Professor Bose, Sudhangshu Name: Danh Tran Toughness measurement of Thermal Barrier Coatings

More information

Chapter 18: Powder Metallurgy

Chapter 18: Powder Metallurgy Chapter 18: Powder Metallurgy ผ ช วยศาสตราจารย เร อโท ดร. สมญา ภ นะยา Reference: DeGarmo s Materials and Processes in Manufacturing 18.1 Introduction Powder metallurgy is the name given to the process

More information

Durability Testing of Ceramic Coatings for Indirect Resistance Heat Treating in Vehicle Lightweighting Applications

Durability Testing of Ceramic Coatings for Indirect Resistance Heat Treating in Vehicle Lightweighting Applications Durability Testing of Ceramic Coatings for Indirect Resistance Heat Treating in Vehicle Lightweighting Applications Warren Peterson and Jerry E. Gould EWI Abstract The need for vehicle lightweighting has

More information

Ti 6Al-4V is recommended for use at service temperatures up to approximately 350 C (660 F).

Ti 6Al-4V is recommended for use at service temperatures up to approximately 350 C (660 F). Titanium Alloy Ti 6Al-4V Type Analysis Carbon (Maximum) 0.10 % Titanium Balance Aluminum 5.50 to 6.75 % Vanadium 3.50 to 4.50 % Nitrogen 0.05 % Iron (Maximum) 0.40 % Oxygen (Maximum) 0.020 % Hydrogen (Maximum)

More information

CHARACTERIZATION OF THIN WALLED Ti-6Al-4V COMPONENTS PRODUCED VIA ELECTRON BEAM MELTING

CHARACTERIZATION OF THIN WALLED Ti-6Al-4V COMPONENTS PRODUCED VIA ELECTRON BEAM MELTING CHARACTERIZATION OF THIN WALLED Ti-6Al-4V COMPONENTS PRODUCED VIA ELECTRON BEAM MELTING Denis Cormier, Harvey West, Ola Harrysson, and Kyle Knowlson North Carolina State University Department of Industrial

More information

Electron Beam Melted (EBM) Co-Cr-Mo Alloy for Orthopaedic Implant Applications Abstract Introduction The Electron Beam Melting Process

Electron Beam Melted (EBM) Co-Cr-Mo Alloy for Orthopaedic Implant Applications Abstract Introduction The Electron Beam Melting Process Electron Beam Melted (EBM) Co-Cr-Mo Alloy for Orthopaedic Implant Applications R.S. Kircher, A.M. Christensen, K.W. Wurth Medical Modeling, Inc., Golden, CO 80401 Abstract The Electron Beam Melting (EBM)

More information

SURFACE TECHNOLOGIES AND ADVANCED MANUFACTURING

SURFACE TECHNOLOGIES AND ADVANCED MANUFACTURING SURFACE TECHNOLOGIES AND ADVANCED MANUFACTURING AEROSPACE POWER GENERATION OIL & GAS www.hycrome.com TEL: +44 (0)1282 418300 FAX: +44 (0)1282 418310 About Hycrome Hycrome was originally established in

More information

Influence of Niobium or Molybdenum in Titanium Alloy for Permanent Implant Application Yuswono Marsumi 1, a and Andika Widya Pramono 1,b

Influence of Niobium or Molybdenum in Titanium Alloy for Permanent Implant Application Yuswono Marsumi 1, a and Andika Widya Pramono 1,b Advanced Materials Research Vol. 900 (2014) pp 53-63 (2014) Trans Tech Publications, Switzerland doi:10.4028/www.scientific.net/amr.900.53 Influence of Niobium or Molybdenum in Titanium Alloy for Permanent

More information

Self Healing Ceramic (Surfaces)

Self Healing Ceramic (Surfaces) Self Healing Ceramic (Surfaces) KIVI NIRIA Jaarcongres 23 november 2011 Matthijn de Rooij University of Twente Laboratory for Surface Technology and Tribology Introduction Technical Ceramics Crystalline

More information

Twin arc wire spraying technology. Spray Wires

Twin arc wire spraying technology. Spray Wires Twin arc wire spraying technology EuTronic Arc Spray Wires Enduring Performance Stronger, with Castolin Eutectic Prolonging the service life of critical components Faster deposition rate Cost effective

More information

STAINLESS STEELS. Chromium and nickel content in the various groups of stainless steels

STAINLESS STEELS. Chromium and nickel content in the various groups of stainless steels These steels contain a high percentage of chromium and sometimes other alloys and have been designed to prevent different types of corrosion. There are two kinds of corrosion: dry corrosion (often named

More information

Plasma Heat and Surface Treatment

Plasma Heat and Surface Treatment Plasma Heat and Surface Treatment Plasmait is a supplier of heat and surface treatment solutions based on plasma technology. We design, build, deploy and support production machinery for continuous and

More information

These elements are in carbon steels in minimal amounts, usually less than 1%.

These elements are in carbon steels in minimal amounts, usually less than 1%. Alloy Steels Weld Tech News VOL 1. NO. 11 WELD TECH NEWS is a newsletter for welders working primarily in maintenance and repair. Each issue contains useful information on materials (cast irons, steels,

More information

Axle Surface Coatings IMechE Seminar 2014

Axle Surface Coatings IMechE Seminar 2014 Excellence In All We Do Axle Surface Coatings IMechE Seminar 2014 Page 1 Axle Surface Coatings Alternatives to current UK practices UK axle surface coatings Limitations of UK axle surface coatings Alternative

More information

Processing of Metal Powders

Processing of Metal Powders Chapter 17 Processing of Metal Powders QUALITATIVE PROBLEMS 17.15 Why is there density variation in the compacting of powders? How is it reduced? The main reason for density variation in compacting of

More information

Characteristics of Wear and Rolling on Fiber Reinforced Metal at High Temperature

Characteristics of Wear and Rolling on Fiber Reinforced Metal at High Temperature Technical Report NIPPON STEEL & SUMITOMO METAL TECHNICAL REPORT No. 111 MARCH 2016 UDC 621. 771. 016. 2 : 669. 771. 07 Characteristics of Wear and Rolling on Fiber Reinforced Metal at High Temperature

More information

Thermal Evaporation. Theory

Thermal Evaporation. Theory Thermal Evaporation Theory 1. Introduction Procedures for depositing films are a very important set of processes since all of the layers above the surface of the wafer must be deposited. We can classify

More information

1 Cutting Tool Materials of common use

1 Cutting Tool Materials of common use 1 Cutting Tool Materials of common use Instructional Objectives At the end of this lesson, the students will be able to (i) Identify the needs and cite the chronological development of cutting tool materials.

More information

Pulsed laser deposition of AlMgB14 thin films

Pulsed laser deposition of AlMgB14 thin films Graduate Theses and Dissertations Graduate College 2008 Pulsed laser deposition of AlMgB14 thin films Jason Curtis Britson Iowa State University Follow this and additional works at: http://lib.dr.iastate.edu/etd

More information

Powder Metallurgy. Science, Technology. and Materials. Anish Upadhyaya. G S Upadhyaya. Department of Materials Science and Engineering

Powder Metallurgy. Science, Technology. and Materials. Anish Upadhyaya. G S Upadhyaya. Department of Materials Science and Engineering Powder Metallurgy Science, Technology and Materials Anish Upadhyaya Associate Professor Department of Materials Science and Engineering Indian Institute of Technology Kanpur, India G S Upadhyaya Former

More information

Study on HVOF spraying replacement of EHC repairing technique

Study on HVOF spraying replacement of EHC repairing technique Study on HVOF spraying replacement of EHC repairing technique SU Xin-Yong Qin Dao Qianjin Naval Yard Qingdao, China 266001 e-mail: suxinyong888@163.com. Abstract The EHC processing can be prepared wear

More information

Anti - Corrosive Finishing

Anti - Corrosive Finishing MSSA Metal Spray Supplies Australia P.O. Box 954 A.B.N. 80 403 448 834 Capalaba Unit 3/37 Veronica Street Queensland 4157 Capalaba, Brisbane Australia Australia Ph: (07) 3823 1004 Fax: (07) 3823 1005 Int

More information

Bearings for Extreme Special Environments - Part 3 Basic Performance of Ceramic (Silicon Nitride) Bearings

Bearings for Extreme Special Environments - Part 3 Basic Performance of Ceramic (Silicon Nitride) Bearings Bearings for Extreme Special Environments - Part 3 Basic Performance of Ceramic (Silicon Nitride) Bearings H. TAKEBAYASHI * *Bearing Engineering Center, EXSEV Engineering Department Outlines of Koyo EXSEV

More information

Joining. 10. Tool Design for Joining. Joining. Joining. Physical Joining. Physical Joining

Joining. 10. Tool Design for Joining. Joining. Joining. Physical Joining. Physical Joining Joining 10. Tool Design for Joining Nageswara Rao Posinasetti The joining processes are generally divided into two classes: mechanical and physical. Mechanical joining does not ordinarily involve changes

More information

For the F/A 18CDEF Programs. 74A J Serialization and Traceability for F/A-18 FC Parts

For the F/A 18CDEF Programs. 74A J Serialization and Traceability for F/A-18 FC Parts = Performed by GKN 74A900003 J Serialization and Traceability for F/A-18 FC Parts 74A900004 M Control of Fracture & Maintenance Crit. Parts for F/A-18 74A900053 J Serialization and Traceability Requirements

More information

Metal Powder the Raw Material of Future Production

Metal Powder the Raw Material of Future Production Metal Powder the Raw Material of Future Production Introduction and Overview Applications for Powder Metallurgy Methods &Systems for Powder Production Physical and Chemical Properties of Metal Powder Economic

More information

Mechanical seals: some developments in face materials

Mechanical seals: some developments in face materials Mechanical seals: some developments in face materials K. Wakely* Carbon has been used as a face material in mechanical seals for well over fifty years. The first grades of carbon used were developed from

More information

NONFERROUS METALS AND ALLOYS

NONFERROUS METALS AND ALLOYS NONFERROUS METALS AND ALLOYS Chapter 7 7.1 Introduction Usage of nonferrous metals and alloys has increased due to technology Possess certain properties that ferrous materials do not have Resistance to

More information

Precision Machining, Grinding & Thermal Spray Since thermal spray coatings metallurgical laboratory machining grinding

Precision Machining, Grinding & Thermal Spray Since thermal spray coatings metallurgical laboratory machining grinding Precision Machining, Grinding & Thermal Spray Since 1960 thermal spray coatings metallurgical laboratory machining grinding MACHINING, GRINDING & THERMAL SPRAY SOLUTIONS Full service manufacturing, thermal

More information

BIOACTIVE SILICIUM-CONTAINING COATINGS ON TITANIUM SUBSTRATE

BIOACTIVE SILICIUM-CONTAINING COATINGS ON TITANIUM SUBSTRATE Powder Metallurgy Progress, Vol.11 (2011), No 3-4 271 BIOACTIVE SILICIUM-CONTAINING COATINGS ON TITANIUM SUBSTRATE O. S. Antonova, V. V. Smirnov, S. M. Barinov, N. V. Bakunova, Ľ. Medvecký, J. Ďurišin

More information

PIM Technology. a powder technology for complex small engineering parts

PIM Technology. a powder technology for complex small engineering parts a powder technology for complex small engineering parts Powder Injection Moulding () metals (MIM) ceramics (CIM) cemented carbides (CCIM) is a new process for material shaping that combines the flexibility

More information

Material and Process. Specification

Material and Process. Specification s 146-67- 1 of 7 Document By: Title Name 1. Purpose 1.1 This document defines approved revision levels of Material and Process specifications used by Onboard Systems. This list is for supplier reference

More information

Titanium and titanium alloys. Josef Stráský

Titanium and titanium alloys. Josef Stráský Titanium and titanium alloys Josef Stráský Lecture 3: Technological aspects of Ti alloys Pure Ti metallurgy, properties and applications α+β alloys microstructures, metallurgy, heat treatment Ti-6Al-4V

More information

Index. Automotive engines, silicon nitride products development, 83-94

Index. Automotive engines, silicon nitride products development, 83-94 Index Advanced composite ceramics, properties and applications, 109-22 Aircraft engine bearings, shaft speed limits, 46-8 Alumina cast sintered, applications, 72-5 comparative erosive wear performance,

More information

Beechcraft Corporation Special Processes Index Special Processes that Require Approval to Perform

Beechcraft Corporation Special Processes Index Special Processes that Require Approval to Perform Brazing Note: Part Number-specific approval is required for Suppliers who do not hold Nadcap Welding/Brazing certification. Silver brazing requires Part Number-specific approval in all cases. Contact:

More information

Thermal Spraying. OSAKA FUJI Corporation

Thermal Spraying. OSAKA FUJI Corporation Spraying A SURFACE COATING TECHNIQUE Items Water plasma Gas plasma High velocity oxygen fuel Electric arc Flame (wire,rod,powder) http://www.ofic.co.jp/en/ OSAKA FUJI Corporation 1-9-1 Jokoji, Amagasaki-shi,

More information

Development of Oil-impregnated Sintered Bearing of Low Wear and Corrosion Resistance

Development of Oil-impregnated Sintered Bearing of Low Wear and Corrosion Resistance New Product Development of Oil-impregnated Sintered Bearing of Low Wear and Corrosion Resistance Kazuhiro KIMURA Recently, oil-impregnated sintered bearings, which are slipping bearings, are used for a

More information

VBN Components AB. 3D-printing for demanding applications. ESS, Max IV, IUC Syd/Big Science Dk Lund,

VBN Components AB. 3D-printing for demanding applications. ESS, Max IV, IUC Syd/Big Science Dk Lund, VBN Components AB 3D-printing for demanding applications ESS, Max IV, IUC Syd/Big Science Dk Lund, 2017-09-19 Ulrik Beste CTO, VBN Componens AB ulrik.beste@vbncomponents.com 070 235 86 26 VBN Components

More information

true grit minerals CUMI lative range of EMD PRODUCT CATALOG 100 years US $ 3 billion 29 companies +30,000 people MURUGAPPA GROUP

true grit minerals CUMI lative range of EMD PRODUCT CATALOG 100 years US $ 3 billion 29 companies +30,000 people MURUGAPPA GROUP MURUGAPPA GROUP 100 years US $ 3 billion 29 companies +30,000 people EMD ELECTRO MINERALS DIVISION CUMI lative range of true grit minerals PRODUCT CATALOG FUSED PRODUCTS MACRO REGULAR BROWN FUSED ALUMINA

More information

1-Materials Science & Materials Engineering

1-Materials Science & Materials Engineering 1-Materials Science & Materials Engineering 1-1-Structure & Properties Relationship (Materials Science or Materials Engineering) Processing Structure Properties Performance Sub Atomic Atomic Sub Atomic

More information

Modern Methods of Surface Engineering

Modern Methods of Surface Engineering LVIV POLYTECHNIC NATIONAL UNIVERSITY Modern Methods of Surface Engineering Institute of Engineering Mechanics and Transport Department of Applied Materials Science and Materials Engineering Asssistant

More information

Amilon. The Alternative to Rulon

Amilon. The Alternative to Rulon Amilon The Alternative to Rulon It all starts with the right material Because we control our own PTFE compounding, sintering, and machining, we are able to create PTFE shapes or components to your exact

More information

Experimental O 3. Results and discussion

Experimental O 3. Results and discussion Introduction Surface coatings to protect against oxidation extend the service temperature and the service life of basic metals. The commercially used coating systems can be divided into three main groups:

More information

STEELS & COATINGS FOR CUTTING TOOL APPLICATIONS

STEELS & COATINGS FOR CUTTING TOOL APPLICATIONS STEELS & COATINGS FOR CUTTING TOOL APPLICATIONS Requirements for cutting tools There are several characteristics that are essential to the good performance of a cutting tool. Powder Metal High Speed Steels

More information

Praxair and TAFA Arc Spray BondArc Wire75B

Praxair and TAFA Arc Spray BondArc Wire75B File: Issue: Supercedes: 1.9.1.2-75B L11111 K10328 Praxair and TAFA Arc Spray BondArc Wire75B Material Review: BondArc 75B wire, a unique nickel-aluminum alloy for use in arc spray systems, is available

More information

Mold Design. 12. Mold Materials. Bong-Kee Lee School of Mechanical Engineering Chonnam National University

Mold Design. 12. Mold Materials. Bong-Kee Lee School of Mechanical Engineering Chonnam National University 12. Mold Materials Bong-Kee Lee Chonnam National University Mold Materials easy toolmaking good performance during production good machining properties ease of hear treatment where hardening is required

More information

Electrochemical Die-Sinking (ECM) in Practice

Electrochemical Die-Sinking (ECM) in Practice Electrochemical Die-Sinking () in Practice Copyright by Maschinenfabrik Köppern GmbH & Co.KG. Distribution, forwarding or duplication of this document, whether in part or in full, is only allowed with

More information

Hot-Dip Galvanized Fabrication Considerations

Hot-Dip Galvanized Fabrication Considerations Hot-Dip Galvanized Fabrication Considerations TECHNICAL BULLETIN JANUARY 27, 2016 Forming Hot-dip galvanized sheet can be formed almost as readily as uncoated cold rolled sheet. It can be formed in a variety

More information

Operating Status of Uprating Gas Turbines and Future Trend of Gas Turbine Development

Operating Status of Uprating Gas Turbines and Future Trend of Gas Turbine Development Operating Status of Uprating Gas Turbines and Future Trend of Gas Turbine Development KEIZO TSUKAGOSHI* 1 JUNICHIRO MASADA* 1 AKIMASA MUYAMA*1 YOICHI IWASAKI* 1 EISAKU ITO* 2 Large frame gas turbines for

More information

STANDARD PRODUCT RANGE. FRIALIT -DEGUSSIT High Performance Ceramics. www-friatec-ceramics.com

STANDARD PRODUCT RANGE. FRIALIT -DEGUSSIT High Performance Ceramics. www-friatec-ceramics.com STANDARD PRODUCT RANGE FRIAIT -DEGUSSIT High Performance Ceramics www-friatec-ceramics.com CONTACT Marc erenard Phone: +33 (0)1 85 78 38 04 Email: marc.lerenard@eu.umicore.com MATERIAS Material FRIATEC-Brand

More information

TECHNOLOGY PLASMA. Ahornweg Weikersheim, Germany

TECHNOLOGY PLASMA. Ahornweg Weikersheim, Germany TECHNOLOGY TECHNOLOGY The plasma process is used to optimally prepare material surfaces before processes such as gluing, soldering, bonding, wire-bonding, injection molding, potting, coating, printing

More information

Nontraditional Machining Processes

Nontraditional Machining Processes Nontraditional Machining Processes The NTM processes can be divided into four basic categories: I. Chemical (Chemical reaction), II. Electrochemical (Electrolytic dissolution), III. Mechanical (Multipoint

More information

PRECISION POLYURETHANES

PRECISION POLYURETHANES Company Profile: We at PRECISION POLYURETHANES manufacture and supply various types of Hi - Performance Cast Polyurethane components and other polyurethane products engineered for multipurpose industrial

More information

special hot work tool steel CR7V-L

special hot work tool steel CR7V-L special hot work tool steel CR7V-L T h e p r e m i u m s t e e l w i t h m a x i m u m h i g h t e m p e r at u r e w e a r r e s i s ta n c e 2 From the casting of steel to finished die... LONG-STANDING

More information

2890 Ligonier St. Latrobe, PA Phone Fax Toll Free

2890 Ligonier St. Latrobe, PA Phone Fax Toll Free Your Best Choice For Carbide Components 2890 Ligonier St. Latrobe, PA 15650 Phone 724.532.3041 Fax 724.532.3043 Toll Free 800.862.7066 www.extramet.net OUR HISTORY OUR MISSION Extramet s Primary Objective

More information

ZYBF. High Temperature Yttria Stabilized Zirconia Fibers. Advanced Fibrous Ceramics

ZYBF. High Temperature Yttria Stabilized Zirconia Fibers. Advanced Fibrous Ceramics Advanced Fibrous Ceramics ZYBF High Temperature Yttria Stabilized Zirconia Fibers The Unrivaled Industry Leader of ZrO 2 Insulation Three Product Types ZYBF-1 (7.5 pcf) ZYBF-2 (21 pcf) ZYBF-5 (16 pcf)

More information

YEOMANS SUBMERSIBLE SOLIDS-HANDLING WASTEWATER PUMPS YEOMANS

YEOMANS SUBMERSIBLE SOLIDS-HANDLING WASTEWATER PUMPS YEOMANS YEOMANS SUBMERSIBLE SOLIDS-HANDLING WASTEWATER PUMPS YEOMANS SERIES 9100 - SUBMERSIBLE NON-CLOG PUMPS SERIES 9235 - DRY-PIT SUBMERSIBLE NON-CLOG PUMPS SERIES 9500 - STAINLESS STEEL SUBMERSIBLE NON-CLOG

More information