PercoTop Primer 010 CS310 / CS311 / CS312 / CS313 / CS315 / CS316 1K Primer
|
|
- Leslie Poole
- 6 years ago
- Views:
Transcription
1 Description PercoTop Primer 010 is a solvent borne zinc chromate-free 1K primer. Composition based on polyvinyl butyral. Products CS310/CS311/CS312/CS313/CS315/CS316 CS010-CS095 CS600 PercoTop Tints PercoTop Thinner Standard Colours CS310: ca RAL CS311: ca RAL CS312: ca RAL CS313: ca RAL CS315: colourless. CS316: ca RAL 1015 Properties Very fast drying. Very good adhesion on metal substrates as listed below. Provides a very fine and smooth surface. Indoor use without warm-humid or wet conditions. Substrates Steel, aluminium and non-ferrous metal. Galvanic and sendzimir zinc coated steel. 1/5
2 Surface preparation Substrates must be free from all contaminants. Because of the wide variety of substrates and their manufacturing processes, a preliminary test should be carried out on the respective substrate to ensure that the pretreatment is sufficient to guarantee a perfect adhesion. For information on substrate and respective surface preparation, refer to the supplier s specifications. VOC value ready for use (EU Directive 1999/13/EC) RAL 9010: 706 g/l 25 % CS600 inclusive. RAL 9005: 711 g/l 25 % CS600 inclusive. 2/5
3 Product preparation Thinner Recommended dry film thickness CS µ Application Gravity feed Application viscosity Thinner Spray nozzle Pressure Number of coats DIN 4 at 20 C (s) (%) (mm) (bar) Suction feed (High pressure spraying) HVLP (Low pressure spraying) Airless air 1-2 Airmix Ca 100 Pressure pot air 2 Membrane pump (High pressure spraying) Electrostatic According to the advice of the DuPont Technical Representative. 3/5
4 Drying Air drying at 20 C Dust dry Dry to handle Dry to recoat Dry 25 µ dry film thickness 10 minutes 15 minutes 30 minutes 30 minutes Forced drying Drying time Drying temperature Flash time: 5 minutes. Depending on film thickness. 10 minutes 60 C object temperature Recoatability Recoatable Remarks With PercoTop and Imron topcoats. Recoating with above mentioned products without sanding is possible. Product data Package viscosity s DIN 4 Flash point 25 C Solids Density Theoretical coverage Theoretical consumption (at 25 µ) (at 25 µ) Weight (%) (kg/l) (m 2 /kg) (g/m 2 ) +/- 1 +/ White Packaged Black Packaged /5
5 Remarks Stir before use. Storage Conditions Shelf life at 5 C to 35 C Material has to be stored at a temperature between 5 C and 35 C. Refer to the label on the original can. Safety Consult the Safety Data Sheet prior to use. Observe the precautionary notices displayed on the container. Information The information provided herein corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific designated; these data may not be valid for such used in combination with any other s or additives or in any process, unless expressly indicated otherwise. The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific for your particular purposes. Since DuPont cannot anticipate all variations in actual end-use conditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this publication is to be considered as a license to operate under or a recommendation to infringe any patent rights. This Technical Data Sheet supersedes all previous issues. Copyright 2011 DuPont. All rights reserved. The DuPont Oval Logo, DuPont, The miracles of science and all products denoted with or are registered trademarks or trademarks of E. I. du Pont de Nemours and Company or its affiliates 5/5
DP4101 / DP4104 / DP4107 HS PRIMER
Description 2-component High Solids primer with 2 methods of application: a. primer surfacer; b. non-sanding primer. Colour: white, medium grey and black. Composition based on a special hydroxy functional
More informationTechnical Data Sheet CC6400 STANDARD VOC CLEAR. Effective October 5, Description
Description 2-component clear based on Low Emission resin technology, to be used in clear over base system. Composition based on acrylic copolymer and a unique, patented "star" polymer technology. Products
More information10P20-14 High Solids Low IR Primer
Technical Data Sheet Product Group Epoxy Primer Characteristics Product Information - A high solids primer for aircraft exteriors meeting the low infrared reflectance requirements of the referenced specification.
More informationAerodur CF Primer 37047
AkzoNobel Aerospace Coatings Technical Data Sheet Product Group Polyurethane Primers Characteristics Product Information is a 3-component chromate free isocyanate cured modified polyurethane primer for
More informationPRODUCT DATA SHEET Sika Unitherm Platinum
PRODUCT DATA SHEET Solvent free, ultra high build, two pack, modified epoxy resin based, intumescent fire protection coating for internally or externally exposed structural steel. Ideal for in-shop application.
More information10P2-3 Anti-static Conductive Flat Black Epoxy Coating
Technical Data Sheet Product Group Conductive epoxy coating Characteristics Product Information This epoxy coating is designed to produce an anti-static conductive film on fiberglass components. It can
More informationRefer to Substrates & Surface Preparation.
SELECTION & SPECIFICATION DATA Generic Type Description Features Color Finish Primer Dry Film Thickness Aliphatic Acrylic Polyurethane Thin film, high gloss finish with exceptional weathering performance
More informationCorlar 2.1 PR-P High Solids Productive Epoxy Primer For Use With FG-040, FG-041 or FG-042 Activators
Corlar 2.1 PR-P High Solids Productive Epoxy Primer For Use With FG-040, FG-041 or FG-042 Activators GENERAL DESCRIPTION A high solids, two component, high build, VOC conforming (2.1 lbs./gal.) Low HAPS
More informationHS High-Build, Primer Surfacer P /1028. HS High-Build, Primer Surfacer P / Grey / White
Product Data Sheet February 2018 INTERNATIONAL MASTER FOR PROFESSIONAL USE ONLY Product P565-1027/8 Product Description HS High-Build, Primer Surfacer P565-1027 /1028 - Grey / White Description HS High
More informationCA8310B (Activator) CA8360 meets the performance requirements of: Mil-PRF FS BS2X34B
Desothane HS Polyurethane Topcoat Near Matt TECHNICAL DATA SHEET Product Description is a high durability, polyurethane topcoat, designed for use as both an internal topcoat for aircraft structural components
More informationCarboguard 890 PRODUCT DATA SHEET SELECTION & SPECIFICATION DATA. Generic Type. Cycloaliphatic Amine Epoxy
SELECTION & SPECIFICATION DATA Generic Type Description Features Color Finish Primer Cycloaliphatic Amine Epoxy Highly chemical resistant epoxy mastic coating with exceptionally versatile uses in all industrial
More informationCorlar 2.1 PR-P High Solids Productive Epoxy Primer
Corlar 2.1 PR-P High Solids Productive Epoxy Primer GENERAL DESCRIPTION A high solids, two component, VOC conforming (2.1 lbs./gal.) Low HAPS productive primer based on Axalta modified polyamide epoxy
More informationPRODUCT GUIDE: ZINC-RICH COATINGS. Version:
PRODUCT GUIDE: ZINC-RICH COATINGS Version: 08.07.17 305 Zinc Rich Epoxy Polyamide Primer Description: 305 is a user friendly zinc-rich epoxy primer formulated for use as a primer under acrylic, epoxy,
More informationApproved. Property Test/Standard Description. gloss (70-85) Flash point ISO 3679 Method 1 32 C calculated VOC-US/Hong Kong. US EPA method 24 (tested)
Approved 30060;30061 1,2 30060 polyurethane ^(ValidationDate) 1 Product description This is a two component chemically curing aliphatic acrylic polyurethane coating. It has a glossy finish with very good
More informationBasecoat WB Technical Data Sheet 09 / 05 / 2016 L UK & Ireland Basecoats
Description One component, mixing machine water based basecoat system. Available in a wide variety of colours including metallic, pearls and solids. Specifically designed for the refinishing of passenger
More informationGently shake the Autowave can prior to use. Prior to clearcoat application: Until completely matt at 25 C 15 minutes at 25 C
Description Autowave waterborne basecoat provides excellent coverage, metallic control and sprayability when used to duplicate OEM solid, metallic and pearl effect colors. Autowave must be used in conjunction
More information1.4 kg/l (11.4 lb/us gal) Maximum 295 g/kg (Directive 1999/13/EC, SED) Maximum 420 g/l (3.5 lb/gal) 50 to 63 μm (2.0 to 2.
DESCRIPTION One-component, heat-resistant silicone acrylic topcoat primarily for the PPG HI-TEMP 1027 primer or the PPG HI-TEMP 222 G primer. PRINCIPAL CHARACTERISTICS Heat-resistant silicone acrylic topcoat
More information58 Series Polyurethane topcoat
Product Group Polyurethane topcoat Characteristics Product Information - This two component high solids polyurethane finish is formulated for application to military aircraft, and is designed to provide
More informationUse suitable respiratory protection Akzo Nobel Car Refinishes recommends the use of a fresh air supply respirator
Description Autobase Plus basecoat provides excellent coverage, metallic control and sprayability when used to duplicate OEM solid, metallic and pearl colour effects. Autobase Plus must be used in conjunction
More information1.4 kg/l (11.4 lb/us gal) Maximum 272 g/kg (Directive 1999/13/EC, SED) Maximum 420 g/l (3.5 lb/gal) To 650 C (1200 F) To 538 C (1000 F)
DESCRIPTION One component heat resistant silicone topcoat for use in an elevated temperature coating system, primarily for application over PPG HI-TEMP 1027 primer PRINCIPAL CHARACTERISTICS Heat resistant
More informationAliphatic Acrylic-Polyester Polyurethane
SELECTION & SPECIFICATION DATA Generic Type Description Features Color Finish Primer Dry Film Thickness Aliphatic Acrylic-Polyester Polyurethane High build, low sheen finish that has excellent resistance
More informationEclipse ECL-G-2 Clear High Solids Polyurethane Topcoat
Technical Data Sheet Product Group Polyurethane topcoat Characteristics Product Information ECL-G-2 is a high solids, long life clear coat formulated for use with Eclipse base coat and special effect colors
More informationHS CLEAR
HIGH SOLIDS ACRYLIC CLEAR HS CLEAR 0300 offers high solid content, fast drying, strong film hardness, and excellent gloss, with the flexibility of different hardener options, and simple mixing ratios for
More informationOne-coat application 5 LV650 Clear 2 LV650 Hardener 1 LV650 Reducer Anti-Graffiti (#484165)
Description Autocoat BT is a two component VOC compliant clear coat that provides excellent chemical resistance and stain repellent properties. is designed for original equipment and repairs of commercial
More informationAbcite 585 EF. Technical Data and Application Guide. Product description. Typical applications. Product range. Product certifications.
Product description is a single layer, primer-free, halogen-free, high strength adhesive thermoplastic powder coating which provides shattering protection for glass pieces and preserves the original glass
More information4970 PRIME COAT FZ Two components zinc phosphate epoxy product
Converter name Destination Extremely versatile use: industrial vehicles, agricultural machines, different metal surfaces, (trussing, external pipes). Contains zinc phosphate as anticorrosive pigment. Doesn
More informationApproved. Property Test/Standard Description. high gloss (85+) Flash point ISO 3679 Method 1 30 C. US EPA method 24 (tested)
Approved 9600;9620 1,2 9600 polysiloxane ^(ValidationDate) 1 Product description This is a two component chemically curing polysiloxane resin based coating. The product does not contain isocyanates and
More informationProperty Test/Standard Description. Flash point ISO 3679 Method C
Other Technical Data Sheet 2906;2907 6 2906 VValidationDate). 1 Product description This is a two component finishing filler. It is a smooth multi purpose product. It has good sanding properties, strong
More informationSIGMACAP MASTIC GF. September surface tolerant coating for lower grade of steel preparation
5 pages DESCRIPTION PRINCIPAL CHARACTERISTICS COLOURS AND GLOSS BASIC DATA AT 20 C Mass density Volume solids VOC (supplied) Recommended dry film thickness Theoretical spreading rate Touch dry after Overcoating
More informationTechnical Data Sheet S Topcoats LV 351 TOPCOAT MM/RM FOR PROFESSIONAL USE ONLY
100 Topcoat 40 Hardener 30 Reducer Description: High gloss, state of the art 2K High Solids polyurethane topcoat. The target use for this product is refinishing and refurbish of existing vehicles and the
More information64C1-2-A High Temperature Resistant Insulative Coating
Product Group Characteristics Product Information High temperature coating is formulated for use as a high temperature insulation coating for environments with continuous exposure to temperatures up to
More informationProperty Test/Standard Description
Approved 720 1,2 720 silicone acrylic ^(ValidationDate) 1 Product description This is a one component physically drying silicone acrylic coating. It is heat resistant up to 600 C. Can be used as primer,
More informationMix ratio (by volume): (base component) (activator component) (thinner component)
TECHNICAL DATA SHEET Product Description DeSoto High Temperature urethane primer is a heat resistant coating that can withstand an operating temperature of 232 C (450 F). is used over aluminum and composite
More informationGRIP-GARD PLUS BRUSH / ROLL ADDITIVE
Description The GRIP-GARD PLUS Brushing/Rolling Additive is designed to convert GRIP-GARD PLUS spray paint into a coating that can be used for brush & roll application. 100 Grip Gard Plus (High Gloss)
More informationProperty Test/Standard Description
Approved 1505;1506 1,2 1505 phenolic/novolac epoxy ^(ValidationDate) 1 Product description This is a two component polyamine cured phenolic/novolac epoxy coating. It is heat resistant up to 205 C (401
More informationTested in accordance with ISO , high expected durability in corrosivity category C5-I. Property Test/Standard Description
Approved 7461;7680 1,2 7680 zinc epoxy ^(ValidationDate) 1 Product description This is a two component polyamide cured zinc rich epoxy coating. It is a high solids, high zinc dust containing product. It
More informationApproved. Property Test/Standard Description. gloss (70-85) Flash point ISO 3679 Method 1 25 C calculated VOC-US/Hong Kong. US EPA method 24 (tested)
Approved 612;625;627 1,2 625 epoxy ^(ValidationDate) 1 Product description This is a two component polyamide cured epoxy coating. It has a glossy finish with fair gloss retention. To be used as topcoat
More informationProperty Test/Standard Description
Approved 16480;18120 1,2 16480 polyurethane ^(ValidationDate) 1 Product description This is a two component chemically curing aliphatic acrylic polyurethane coating. This product contains no solvents on
More informationProperty Test/Standard Description
Approved 515;519;527;1549 1,2 515 epoxy mastic ^(ValidationDate) 1 Product description This is a two component polyamine cured epoxy mastic coating. It is a surface tolerant, high solids, high build product.
More informationProperty Test/Standard Description
Approved 32222;32223;35142 1 32222 epoxy composite ^(ValidationDate) 1 Product description This is a two component glass flake reinforced epoxy composite coating. It is heat resistant up to 250 C (482
More informationtwo component high build amine adduct cured phenolic epoxy primer
5 pages Revision of January 2003 DESCRIPTION two component high build amine adduct cured phenolic epoxy primer PRINCIPAL CHARACTERISTICS primer coat in the Sigma Phenguard tank coating system excellent
More informationProperty Test/Standard Description
Approved 1537 1,2 1537 alkyd ^(ValidationDate) 1 Product description This is a one component oxidatively drying alkyd coating. It is a fast drying, high build, zinc phosphate pigmented product. Can be
More informationPre-qualification testing in accordance with NORSOK M-501, Rev. 5, System 1, suitable for exterior exposure in offshore environment, below 120 C.
Approved 402;2521 1,2 2521 zinc epoxy ^(ValidationDate) 1 Product description This is a two component polyamide cured zinc rich epoxy coating. It is a very high zinc dust containing product. It conforms
More informationCorlar 2.8 HG High Solids Epoxy
Corlar 2.8 HG High Solids Epoxy GENERAL DESCRIPTION A high build, high solids, two-component, VOC conforming (2.8 lbs./gal.), high gloss epoxy based on Axalta modified polyamide epoxy technology. The resulting
More informationERC5 Erosion Resisting Polyurethane Coating
TECHNICAL DATA SHEET Product Description Components is a two pack, polyurethane erosion resisting coating developed for the protection of strike areas and leading edges of aircraft. When applied over the
More informationP WB Engine Bay Basic P Activator for WB Engine Bay Basic P Aquabase Plus Thinner P Aquabase Plus Slow Thinner
Product Data Sheet December 2016 INTERNATIONAL MASTER FOR PROFESSIONAL USE ONLY Aquabase Plus Engine Bay Repair Process Product Description P935-1135 WB Engine Bay Basic P210-9115 Activator for WB Engine
More informationProperty Test/Standard Description
Approved 29560;29561 1 29560 zinc silicate ^(ValidationDate) 1 Product description This is a two component ceramically reinforced polyamide cured zinc rich epoxy coating. 1:1 mixing ratio for easy use
More informationApproved. Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method C calculated VOC-US/Hong Kong. US EPA method 24 (tested)
Approved 28780 1,2 28780 acrylic ^(ValidationDate) 2 Product description This is a one component water borne acrylic emulsion coating. It is a versatile, fast drying product for exterior and interior use.
More informationProduct Information D8120
Product Information High Solids 2-Pack Clearcoat PRODUCTS Deltron Clear Deltron s D803, D841, D861 Deltron Accelerated D863 Deltron s D870, D807,D872, D873 Deltron DG Fade-out D868 For matt, satin and
More informationCorlar LV PR 178 Series Epoxy Primer
Corlar LV PR 178 Series Epoxy Primer GENERAL DESCRIPTION A two-component very low VOC corrosion-resistant epoxy primer designed to be extremely tough and durable. When properly activated, the combined
More informationProperty Test/Standard Description. US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)
Approved 402;2522 1,2 2522 zinc epoxy ^(ValidationDate) 1 Product description This is a two component polyamide cured zinc rich epoxy coating. It is a high zinc dust containing product. It conforms to
More informationMix ratio (by volume): 529K002 (base component) 910K021 (activator component)
TECHNICAL DATA SHEET Product Description DeSoto high temperature epoxy topcoat can withstand an operating temperature of up to 204 C (400 F). It is used over high temperature coatings such as 519X303 and
More informationDPHS521 FL301. Low VOC Primer
Product Information Bulletin Effective 1/99 Low VOC Primer DPHS52 DPHS52 is a 3.5 VOC epoxy primer or primer surfacer designed specifically for use in fleet refinishing operations. The product is lead
More informationPDS N5.9.1 March 2005 P HS CLEARCOAT PRODUCT DESCRIPTION
PDS N5.9.1 March 2005 P190-643 HS CLEARCOAT PRODUCT DESCRIPTION P190-643 is a premium quality High Solids Acrylic Urethane Clearcoat. When combined with Nexa Autocolor Hardeners and Thinners, HS Clearcoat
More information4002A21M Aluminum Lipskin Coating
Technical Data Sheet Product Group High heat coating Characteristics Product Information This specialty coating is designed for use on the leading edges of aluminum alloy nose cowl inlets. It is formulated
More informationProperty Test/Standard Description. semi gloss (35-70) Flash point ISO 3679 Method 1
2080;2081 1 2080 epoxy VValidationDate). 1 Product description This is a two component polyamide cured epoxy coating. It is a high solids, high build product. Designed as a mid coat in systems for new
More informationTECH MANUAL TABLE OF CONTENTS
PRO-SPRAY TECH MANUAL TECH MANUAL TABLE OF CONTENTS SURFACE CLEANERS 1-1 ICR-0014, ICR-0015, ICR-1402 1-1 SELF-ETCHING & EPOXY PRIMERS 2-1 A-514 CHROMATE FREE ETCH PRIMER 2-1 A-518 EPOXY PRIMER 2-3 PLASTIC
More informationGeneral Industrial Equipment & Machinery. PercoTop for machine builders. Lighten your load
General Industrial Equipment & Machinery PercoTop for machine builders Lighten your load You protect what you value. That also holds true for large machines, particularly if they are investments worth
More informationProperty Test/Standard Description
Approved 21060;21061 1,2 21060 epoxy ^(ValidationDate) 1 Product description This is a two component polyamine cured epoxy coating. It is a surface tolerant, high solids, high build product. Will continue
More informationProperty Test/Standard Description. semi gloss (35-70) Flash point ISO 3679 Method 1 32 C
Approved 18420;18360 1,2 18420 epoxy ^(ValidationDate) 1 Product description This is a two component amine cured, glass flake reinforced, abrasion resistant epoxy coating. It is a surface tolerant, high
More informationAbcite X45. Technical Data and Application Guide. Product description. Typical applications. Product range. Product certifications.
Product description is a single layer, primer-free, halogen-free, high strength adhesive thermoplastic powder coating which provides excellent and durable corrosion protection to steel and other metals.
More informationDue to the intrinsic quality the CARIZZMA CANDIZZ should be used only for show cars. CARIZZMA CANDIZZ - small areas, 1-2 panels, e.g.
Product description For CANDYS, an ONYX HD ground coat is sprayed, then the CANDIZZ is sprayed over the top of it, followed by an R-M to finish the look. The CANDIZZS set a new standard of color intensity
More informationJanuary 2007 Product Information ENVIROBASE HIGH PERFORMANCE
GLOBAL REFINISH SYSTEM January 2007 Product Information ENVIROBASE HIGH PERFORMANCE PRODUCTS Envirobase Waterborne Basecoat colour T4xx Envirobase Thinner T494 Envirobase High Performance is waterborne
More informationPRODUCT DATA SHEET SikaCor -277
PRODUCT DATA SHEET Epoxy resin-based coating material for wear resistant coatings PRODUCT DESCRIPTION SikaCor-277 is a thixotropic epoxy resin based 2-pack coating material for steel and concrete. SikaCor-277
More informationTechnical Data Jotamastic 80 MIO
Technical Data Jotamastic 80 MIO Product description Jotamastic 80 MIO is a high solids two-pack micaceous iron oxide pigmented, surface-tolerant epoxy mastic coating which can be applied in low film thickness.
More informationProperty Test/Standard Description
Approved 612;617 1,2 617 epoxy ^(ValidationDate) 1 Product description This is a two component, polyamide cured, high molecular weight epoxy coating. Designed as a primer for new construction. Can be used
More informationReady-to-use structural plaster for interior use
Ready-to-use structural plaster for interior use Very easy to spread Very robust and hard-wearing surface Uniform Fibre-reinforced, low-stress Easy and flexible to handle Environmentally friendly, low-odour
More informationTECHNICAL DATA SHEET
PRODUCT : UT105 TWO-PACK ACRYLIC STRUCTURED METALLIC COLOURS Page 1 of 5 DESCRIPTION PROPERTIES COLOUR GLOSS LEVEL WEATHERING CHEMICAL RESISTANCE SOLVENT RESISTANCE ABRASION RESISTANCE TEMPERATURE RANGE
More informationApproved. Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method F (29 C) calculated VOC-US/Hong Kong
Approved 20920;16620 1 20920 epoxy ^(ValidationDate) 1 Product description This is a two component amine cured epoxy coating. It is a fast drying, zinc phosphate pigmented, high solids, high build product.
More informationCROMAX PRO WB9908 SUPER JET BLACK BASECOAT
CROMAX PRO WB9908 SUPER JET BLACK BASECOAT GENERAL DESCRIPTION A super jet black factory package color that delivers the deepest black to meet the most critical color standards. It features high hiding,
More informationProduct Information D8501 D8505 D8507 2K Primer DP4000
GLOBAL REFINISH SYSTEM August 2013 Product Information D8501 D8505 D8507 2K Primer DP4000 D8501 2K primer DP4000 White G1 D8505 2K primer DP4000 Grey G5 D8507 2K primer DP4000 Dark Grey G7 D8238 HS Fast
More informationPRODUCT DATA SHEET Sikafloor -378
PRODUCT DATA SHEET 2-PART TOUGH-FLEXIBLE COLOURED EPOXY SEAL COAT DESCRIPTION is a two part tough-flexible, coloured,epoxy seal coat with improved resistance against amine blushing under critical weather
More informationProduct Data Sheet September 2010
Precleaners P980-251/9010 E1300 Product Data Sheet September 2010 INTERNATIONAL MASTER FOR PROFESSIONAL USE ONLY 2-Pack Polyester Stopper Range Product Description P551-1050 General Purpose Stopper P551-1052
More informationDuPont ETFE Coatings High-Build Topcoat Powder Powder Primer and 699N-129 Liquid Primer
DuPont ETFE Coatings 532-6410 High-Build Topcoat Powder 532-6405 Powder Primer and 699N-129 Liquid Primer Industrial Nonstick Coatings Product Information Ethylene tetrafluoroethylene (ETFE) is a thermoplastic
More informationDate of issue: 5 October 2017 Page: 1/6
Approved 16560;16561;16840 1,2 16560 epoxy mastic ^(ValidationDate) 1 Product description This is a two component polyamine cured epoxy mastic coating. It is a surface tolerant, abrasion resistance, high
More informationTechnical Data Sheet.
Technical Data Sheet. Permahyd Hi-TEC Base Coat Series 480 Permahyd Hi-TEC Base Coat Series 480 is an innovative waterborne base coat system. Hi-TEC is fast, versatile, and easy to blend. After recoating
More informationConstruction. 2-part epoxy protective coating. Product Description. Product Data 1 1/5. Test. Form. Storage
Product Data Sheet Edition 2011-10_1 2-part epoxy protective coating Construction Product Description is a total solid (acc. test method of Deutsche Bauchemie*), two part epoxy resin coating. * German
More informationSilopren* LSR Technical Data Sheet. Silopren LSR 2750
Technical Data Sheet Silopren* LSR 2750 Silopren LSR 2750 Description Silopren LSR 2750 TP 3824 is a two-component liquid silicone rubber for injection moulding, which offers primer-less adhesion to a
More information2K P421 - Single Layer Metallic System Medium Solids. P421-2K Single-layer Metallic colour mixes. P K Air dry lacquer converter
FOR PROFESSIONAL USE ONLY I0320 Date of Issue : July 2002 2K P421 - Single Layer Metallic System Medium Solids Products P421-2K Single-layer Metallic colour mixes P420-/P421-/P425-/P429-2K Mixing basics
More informationFor purchasing information visit: Sikkens Cetol Novatech
The following Technical Datasheet is provided by Manns Wood Finishes Direct cannot be held liable for the information contained within this document. For purchasing information visit: Sikkens Cetol Novatech
More information2-K epoxy resin coating Certified for direct contact with foods
FK 45 FOODGRADE 2-K epoxy resin coating Certified for direct contact with foods Product description is a highly resilient 2K high solid epoxy resin coating. Odourless, fast-drying, for internal areas.
More informationNFCA 400 Field Quality Assurance Procedure for Application of Mastic and Thin-Film Intumescent Fire Resistive Coatings
NFCA 400 Field Quality Assurance Procedure for Application of Mastic and Thin-Film Intumescent Fire Resistive Coatings 1 Scope The application of mastic and thin-film intumescent fire resistive coatings
More informationDuPont Zytel HTN51G50HSL BK083 (Preliminary Data)
PRODUCT INFORMATION DuPont Zytel HTN51G50HSL K083 (Preliminary Product Information Zytel HTN high performance polyamide resins feature high retention of properties upon exposure to elevated temperature,
More informationTECHNICAL DATA SHEET
Page 1of 5 PRODUCT DESCRIPTION PROPERTIES COLOUR GLOSS LEVEL WEATHERING UT100 2-Pack topcoat is an unmodified acrylic polyurethane designed to maintain maximum appearance for the maximum length of time.
More informationNEXA AUTOCOLOR 2K Plastics Painting Process
PDS N7.1 April 2017 NEXA AUTOCOLOR 2K Plastics Painting Process PRODUCT DESCRIPTION The NEXA AUTOCOLOR 2K Plastic Painting Process offers a complete and high quality rage of products for the painting of
More information- Aromatic hydrocarbons - Binder 2,67 kg/dm³ (±0,06 Kg/dm³) Solid content - 80% by weight (±2%) - 58% by volume (±2%) according to ASTM D2697
p. 1/6 ZINGA The Film Galvanising System ZINGA is a one pack coating that contains 96% zinc in the dry film and provides cathodic protection of ferrous metals. It can be used as a unique system as an alternative
More informationDuPont Kevlar THE SCIENCE OF CUT PROTECTION
DuPont Kevlar THE SCIENCE OF CUT PROTECTION Industry standards groups have made tremendous progress in testing and measuring the cut protective performance of gloves and apparel. DuPont has been a pioneer
More informationImron 1.8 FT-C Flat Waterborne Polyurethane Clearcoat
Imron 1.8 FT-C Flat Waterborne Polyurethane Clearcoat GENERAL DESCRIPTION A flat gloss, isocyanate-free, single component, 1.8 lbs/gal VOC conforming, zero HAPs coating based on unique Axalta waterborne
More informationCHROMAPREMIER 42400S / 42410S / 42440S / 42470S 2K PREMIER SEALER
CHROMAPREMIER 42400S / 42410S / 42440S / 42470S 2K PREMIER SEALER GENERAL DESCRIPTION A three-component, high-performance sealer for premium-quality spot, panel and overall repairs. It provides excellent
More informationDuPont ChromaClear G2-4700S (Hyper Cure - Air Dry and Express Bake)
cdupont Automotive Finishes ChromaSystem Technical Manual Description ChromaClear G2-4700S is a second generation version of ChromaClear 4700S. ChromaClear G2-4700S is not only the world s fastest air
More information3MTM FireDamTM Intumescent Coating WB Installation Manual. Thinner is. Better
0808-3086E 3M FD Intumescent Coating WB 1000 - INSTALLATION MANUAL:Layout 1 9/30/08 2:32 PM Page 1 3MTM FireDamTM Intumescent Coating WB 1000 Installation Manual Thinner is Better 3 1 Index 1. Product
More informationDuPont Engineering Polymers for High Performance Extrusion Solutions. October, 2005
DuPont Engineering Polymers for High Performance Extrusion Solutions October, 2005 2 Legal Disclaimer The information and suggestions provided in this presentation are based on data believed to be reliable,
More informationTT-P-1757B Type I, Class C, Aerosol Zinc Chromate Primer. A one component, alkyd base, corrosion inhibiting zinc chromate primer.
941 111313 TT-P-1757B Type I, Class C, Aerosol Zinc Chromate Primer PRODUCT: TT-P-1757B TY.I, CL.C AEROSOL ZINC CHROMATE PRIMER A one component, alkyd base, corrosion inhibiting zinc chromate primer. DESCRIPTION:
More informationSikaCor 255 Epoxy-binder for mortars on concrete and steel. Protective Coatings
Product Data-Sheet Edition 03.09 DS-Code: E 1605 SikaCor 255 Epoxy-binder for mortars on concrete and steel SikaCor 277 Thixotropic epoxy-binder - sag resistant high-build coatings and mortars Protective
More informationSWARCO LIMBURGER LACKFABRIK GmbH Road Marking Systems LIMBOROUTE LW48 TECHNICAL INFORMATION
LIMBOROUTE LW48 TECHNICAL INFORMATION LIMBOROUTE LW48 Art.-No.: 11702 Airless, white Dispersions Dispersion paint Version: 2016-11-14 CONTENTS 1 Main characteristics / Fields of applications... 3 2 Technical
More informationTwo component PU adhesive system. Property 2018/A 2018/B 2018 (mixed)
Advanced Materials Araldite 2018 Structural Adhesives TECHNICAL DATA SHEET Araldite 2018 Two component PU adhesive system Key properties Good UV stability Ideal for bonding thermoplastics Low shrinkage
More informationMaximum Rust Protection!
ZERO-RUST Zero Rust is a direct-to-metal, phenolic modified alkyd rust and corrosion control coating, which controls rust and corrosion by putting down an impermeable barrier at the steel level. Its dielectric
More informationTechnical Datasheet E
Fight rust und prime in a one-step operation Non-polluting as there is no lead, zinc chromate or mineral acid content. Inactivates rust by forming organometallic complexes. Forms a rust-inhibiting protective
More informationProduct Information CHEMGLAZE B 9942 A/B. Coating for Casting Pits. Easy Application Chemglaze B 9942 A/B will bond to damp and wet surfaces.
Product Information Chemical Products Division CHEMGLAZE B 9942 A/B Coating for Casting Pits. FEATURES BENEFITS. Easy Application Chemglaze B 9942 A/B will bond to damp and wet surfaces. Will build to
More informationTechnical Data Sheet
MATTE CONTRACTOR CHOICE PAINT The Matte Contractor Choice C paint is designed for the contractor; it has good performance and opacity. No odor. Has very good brushability, leveling, durability, adhesion
More information