BALL BEARING SKF BEARINGS MANUFACTURED BY ELECTRICAL EROSION

Transcription

1 BALL BEARING SKF BEARINGS MANUFACTURED BY ELECTRICAL EROSION Drd. Ing. IOAN BADIU, Technical University of Cluj-Napoca Prof.univ.dr.ing. MARCEL S.POPA, Technical University of Cluj-Napoca ABSTRACT: Bearings for rotary motion bearings fall and bearings. It differs if the forces between moving parts are sent by rolling or sliding elements. Bearings generally consist of two rings embedded runways. Rolling bodies are disposed between the ring and roll on the raceways. Rolling bodies have different shapes such as balls, cylindrical roller, needle, tapered roller and spherical roller. The cage of the rolling bodies guided by the right, to keep them at a distance of each other and prevent them reaching. Needle bearings and aligning those with central ridge, further ensures proper orientation cage rolling bodies. KEY WORDS : bearings, electrical erosion materials. 1.INTRODUCTION. At camps dismantled, cage keeps bodies running together and thus facilitate mounting bearings. For special applications and use ball bearings, needle roller and cage free. Standard material is sheet steel cages for some applications and brass sheet. Cages are solid brass, steel, thermoplastics or other materials. Very common are the cages of thermoplastics, especially those of glass fiber reinforced polyamide. The guide rings and the rolling bodies are made in particular from steel with high chromium content, heattreated steel and a case hardening. At special camps for extreme conditions - load, speed, temperature, corrosion - the commodities are sealing lip. Requests predominantly radial bearings are called radial bearings. Most applications support combined radial bearings, for example. groove ball bearings, thrust ball bearings radial, tapered roller bearings or spherical roller bearings. Type cylindrical roller bearings N and NO, most needle bearings, needle sleeves and rings can upload only these radial direction. Another feature is the guide shaft to the bearing. Thus, there are bearings which allow axial movement, bearings that guide the shaft in the axial direction in one or both directions and the bearings which allow the angular misalignment between the shaft and the housing. In determining bearing size consider 11

2 steel, plastics, ceramics, and other materials resistant to temperature and / or steel. Bearings are provided in the open version, and sealed on one side or on both sides. The most common types are those with fissure relative motion. At low oscillating or requests at rest is considered as static requested. External dimensions identical roller bearings generally support more stress than the Ball bearings. first request value and type of load - static or dynamic - as well as the operational and safety operation of the suspension. Rotary bearings are generally dynamic stress. Bearings with a slow and medium loads mainly use ball bearings at higher loads and larger shaft diameters predominantly roller. Fig.1.Machine is manufactured by electrical erosion AQ-900. Fig. 2. Material SKD11 12

3 Fig. 3. Processing bearing circular orbits. Fig.4. 3D Graphics bearing. Deep groove ball bearings are designed to take mainly radial loads. They are used for a wide range of applications. Consequently, they are available in many variants. 13

4 Fig.5. Deep groove ball bearings Single row SKF. Fig.6. Deep groove ball bearings SKF double row Fig.7. Deep groove ball bearings SKF selfaligning Fig. 8. The table electrical erosion parameter values Fig. 9. The graph electrical erosion parameters. Fig. 10. The electrical erosion parameter values. 14

5 Fig. 11. Link between the parameters erosion plants. Fig. 12. Electrical erosion productivity parameter values Fig. 13.The table parameters electrical erosion. Fig. 14. The reporting of productivity parameters electrical erosion. Fig. 15. The reporting of productivity parameters electric erosion. Fig. 16. The reporting of productivity parameters electric erosion 15

6 Fig. 17. The reporting of productivity parameters the electrical erosion. Fig. 18. The table parameters the electrical erosion Fig D representation parameters of the electrical erosion. Fig. 20. The table parameters under various graphic shapes. Fig. 21. The electrical erosion parameters the table. Fig D shape parameters the electrical erosion. 16

7 Fig. 23. The table parameters in the form of 2D the electrical erosion Fig. 24. The shape 3D graphics parameters electrical erosion Fig. 25.The electrical erosion parameters the table Fig. 26. The form 3D graphics parameters erosion electric. Fig. 27. Reporting of the electrical erosion productivity parameters. Fig. 28. Reporting of the electrical erosion productivity parameters 17

8 Fig. 29. The productivity curve and other parameters of electrical erosion. Fig. 30. The table parameters electrical erosion Fig. 31. The productivity the reporting of to other parameters Fig. 32. The curves electrical erosion parameters Fig. 33. The parameters the curves the electrical erosion. Fig. 34. Impulse time expressed as a percentage. 18

9 3.CONCLUSIONS. Each bearing type has its characteristic properties and is suitable for various applications such suspension. There are no general rules apply to choosing the type of bearing, because many factors must be evaluated and their mutual influences. Thus, in addition to load and speed, should be considered and temperature, lubrication, vibration, installation, maintenance. In many cases, at least one of the dimensions of the camp - often bore diameter - are already determined by sizing the neighboring building. Thrust bearings are suitable for applications predominantly axial. Spherical thrust bearings thrust bearings and angular contact ball bearings can take both axial and radial. The remaining axial bearings are only suitable for tasks in axial directions. If the gauge is limited radial bearings are chosen such low section eg needle cages, needle sleeves with or without inner ring, ball bearings or spherical bearing different types. Cages are used for axial loading axial needle bearings, thrust needle or Ball bearings. REFERENCES [1] Ailincai, G.: Studiul metalelor,institutul Politehnic Iasi, [2] Balc, N.: Tehnologii neconventionale, Editura Dacia Publishing House, Cluj- Npoca, [3] Bolundut, L.I.: Materiale si tehnologii neconventionale, Editura Tehnica-Info, Chisinau, [4] Buzdugan, Gh., ş.a. Vibraţii mecanice, Editura Didactică şi Pedagogică, Bucureşti, [5] Constantinescu, V., ş.a. Lagăre cu alunecare, Editura Tehnică, Bucureşti [6] Colan, H.: Studiul metalelor, Editura [Didactica si Pedagogica, Bucuresti, [7] Domsa, A.: Materiale metalice in constructia de masini si instalatii, Editura Dacia, [8] Dašić, P.: Technical and ICT Abbreviations and Acronyms. Vrnjačka Banja: SaTCIP Ltd., pp ISBN ] Dašić, P.: Analysis of the journal impact factor in field of mechanical engineering. Plenary and Invitation paper. In: Proceedings of the 11th International Mechanical Industry Volume 1, Sokobanja, Serbia, September Edited by Predrag Dašić. Vrnjačka Banja: SaTCIP Ltd., 2011, pp ISBN [10] Dašić, P.; Natsis, A. and Petropoulos, G.: Models of reliability for cutting tools: Examples in manufacturing and agricultural engineering. Strojniški vestnik Journal of Mechanical Engineering, Vol. 54, No. 2 (2008), pp ISSN ] Dašić, P.; Franek, F.; Assenova, E. and Radovanović, M.: International [12] Gafiţanu, M. ş.a. Organe de maşini, vol. 2. Editura Tehnică, Bucureşti, [13] Nichici, A.: Prelucrarea prin eroziune electrica in constructia de masini, Editura Facla, Timisoara, [14] Olaru, D.N. Tribologie. Elemente de bază asupra frecării, uzării şi ungerii, Litografia Institutului Politehnic Gheorghe Asachi, Iaşi, [15] Popa,M.S.:Masini, tehnologii neconventionale si de mecanica fina-editie Bilingva, Romana-Germana, Editura U.T.PRESS, Cluj-Napoca, [16] Popa, M.S.: Tehnologii si masini neconventionale, pentru mecanica fina si microtehnica, Editura U.T.PRESS, Cluj- Napoca, [17] Popa, M.S.:Tehnologii inovative si procese de productie, Editura U.T.PRESS, 19

10 Cluj-Napoca,2009. [18] Popescu, Luminiţa Georgeta, Cristinel Popescu, Influenţa dispozitivelor de anclanşare automată a rezervei asupra funcţionării întrerupătoarelor de cuplă longitudinală, Analele Universităţii Constantin Brâncuşi din Târgu Jiu, seria Inginerie, nr.2/2010, pp 35-44, ISSN , Revistă categoria B+, [19] Popescu, Luminiţa Georgeta -Aplicaţii ale liniarizării exacte prin reacţii la acţionările de curent continuu, Analele Universităţii Constantin Brâncuşi din Târgu Jiu, seria Inginerie, nr.1/2009, pp 7-14, ISSN , Revistă categoria B+, [20] Rădulescu, Gh., Ilea, M. Fizicochimia şi tehnologia uleiurilor lubrifiante, Editura Tehnică, Bucureşti, 1982, [21] Sofroni, L.: Fonta cu grafit nodular,editura Tehnica, Bucuresti, [22] Trusculescu, M.: Studiul metalelor, Editura Didactica si Pedagogica,Bucuresti,,