Curriculum Vitae EDUCATION: Institute of Joining and Assembly Chemnitz University of Technology Reichenhainer Strasse 70 D Chemnitz, Germany

Transcription

1 Curriculum Vitae Peter Mayr, Univ.-Prof. Dr. Vice Dean Mechanical Engineering Director Institute of Joining and Assembly Chair of Welding Engineering Chemnitz University of Technology Contact Details Office: Institute of Joining and Assembly Chemnitz University of Technology Reichenhainer Strasse 70 D Chemnitz, Germany Tel.: Fax Contact Details Private: Am weißen Stein 20 D Chemnitz, Germany Mobile : Personal Data: Date of Birth: August 19, 1976 Place of Birth: Salzburg, Austria Nationality: Austria Civil Status: Married, 2 children (2, 5 years) EDUCATION: Doctor of Technical Sciences (Dr. techn.), with highest honours Graz University of Technology, Faculty of Mechanical Engineering, Austria, September 2007 PhD Thesis Evolution of microstructure and mechanical properties of the heat affected zone in boron-containing 9% chromium steels, TU Graz (2007), Supervisor Prof. Dr. Horst Cerjak International Welding Engineer (IWE), Accreditation according the International Institute of Welding (IIW) 2006 Master of Science (Dipl.-Ing.), Graz University of Technology, Institute for Materials Science and Welding, Austria, January 2004 Master Thesis Characterisation and examination of the weldability of the high temperature resistant steel grade P23, TU Graz (2003), Supervisor Prof. Dr. Horst Cerjak CV Peter Mayr Page 1 of 6

2 PROFESSIONAL EXPERIENCE Vice Dean, Department of Mechanical Engineering TU Chemnitz, Germany Director, Institute of Joining and Assembly Department of Mechanical Engineering, TU Chemnitz, Germany Professor, Chair of Welding Engineering Department of Mechanical Engineering, TU Chemnitz, Germany Assistant Professor, Group Leader Materials Development, Institute for Materials Science and Welding Graz University of Technology, Austria Senior Researcher, Institute for Materials Science and Welding Graz University of Technology, Austria Researcher, Institute for Materials Science, Welding and Forming Graz University of Technology, Austria 04/ present 08/ present 04/ present 04/ / / / RESEARCH EXPERIENCE ABROAD Visiting Scientist, Department of Materials Science and Engineering, Massachusetts Institute of Technology, USA Prof. Samuel Allen Visiting Scientist, Department of Materials Engineering, The University of Tokyo, Japan Prof. Toshihiko Koseki Observation of phase transformations in steels using high temperature laser scanning microscopy" Visiting Scientist, Heat Resistant Design Group, National Institute for Materials Science (NIMS), Tsukuba, Japan Dr. Fujio Abe Characterisation of base materials and weldments of creep resistant steels using most advanced electron microscopic methods" Researcher, Belgian Welding Institute (BWI), Gent, Belgium, Prof. Alfred Dhooge, 09/ / / / /2002 Characterisation of crossweld microstructures by physical weld simulation using a GLEEBLE thermal simulator and microscopic investigations" CV Peter Mayr Page 2 of 6

3 HONORS AND AWARDS Professor Koichi Masubuchi Award, American Welding Society, 2013 Congress Award Graz 2008, IIW Annual Assembly and International Conference, Graz Max Kade Fellowship 2008, Austrian Academy of Sciences, Max Kade Foundation, NY Henry Granjon Prize 2008, International Institute of Welding (IIW) Dr. Wolfgang Houska Prize 2007, 100k, B&C Privatstiftung TEACHING EXPERIENCE 10+ years of experience in teaching at academic institutions experience in teaching small groups to 200+ students courses offered at Bachelor, Master and PhD level continuous training in teaching and didactics through participation in expert courses Lectures, Exercises and Laboratories for Bachelor courses in: Automotive Manufacturing, Mechanical Engineering, Systems Engineering, Sports Engineering, Industrial Engineering, Microtechnology/Mechatronics Lectures, Exercises and Laboratories for Master courses in: Automotive Manufacturing, Mechanical Engineering, Lightweight Engineering, Sports Engineering, Industrial Engineering, Medical Engineering Courses for Bachelor Degree: Manufacturing Technology, Manufacturing Engineering, Joining Technology, Materials Science Laboratory, Materials Science Seminar Courses for Master Degree: Selection of Engineering Materials, Failure Analysis, Materials Science and Welding Laboratory, Integrative Laboratory Materials, Advanced Materials Science, Materials Science Seminar, Beam Processes, Materials and Joining, Joining of Lightweight Metals, Joining in Medicine SUPERVISED STUDENTS Supervision of students at Bachelor, Master, PhD and post-doctoral level At present, supervision of 19 PhD candidates working in welding technology, mechanical joining, lightweight structures, structural simulation, microstructure evolution, joining of non-ferrous metals, metal-plastic joining, etc. CV Peter Mayr Page 3 of 6

4 POSITIONS IN THE UNIVERSITY SELF-GOVERNMENT Extended Senate, Member Chemnitz University of Technology Vice-Dean for Strategy and Interior Affairs Faculty Executive Committee, Member Habilitation and Doctoral Committee, Member Academic Planning and Examining Committee, Member Medical Engineering, BSc, MSc Academic Planning and Examining Committee, Member Textile Structures and Technologies, MSc Further Duties Chairman Search Committee, Strategy Committee, Quality Management, etc. COMMITTEES, ACTIVITIES AND EXTRA-CURRICULAR ACTIVITIES European Commission, Horizon 2020 Expert Research Fund for Coal and Steel RFCS TGS 6 Physical metallurgy and design of new generic steel grades European Commission Expert European Technical Working Group of experts in fabricated metal products manufacturing European Virtual Institute on Knowledge-based Multifunctional Materials AISBL (KMM-VIN), Chairman WG2 Materials for Energy Welding and Joining German Research Foundation (DFG) Expert German Federation of Industrial Research Associations (AiF) Expert Sonderfachgutachter present present present present present CV Peter Mayr Page 4 of 6

5 American Welding Society (AWS), Chairman German Section Director, Steinbeis Innovation Center Joining Technology Steinbeis Network, Germany Director, Steinbeis Transfer Center Welding and Joining Steinbeis Network, Germany International Institute of Welding (IIW), Chairman Commission IX-C Behaviour of metals subjected to welding creep and heat resistant welds ; European Creep Collaborative Committee (ECCC), Austrian representative in the ECCC Management Committee and member of working Group WG3A Ferritic Steels present present present present Conference Organisation THERMEC - International Conference on Processing & Manufacturing of Advanced Materials Topic Symposium Coordinator, Executive Committee 11 th International Seminar Numerical Analysis of Weldability, Seggau Conference Co-Chairman FUEMOTEC Scientific Conference Series on Joining and Assembly, (in German) TU Chemnitz Assistentenseminar der Wissenschaftlichen Gesellschaft Fügetechnik des DVS, Lichtenwalde 8. Chemnitzer Symposium Füge- und Schweißtechnik 2012, Conference Chairman IIW International Conference Safety and Reliability of Welded Components in Energy and Processing Industry, IIW Annual Assembly 2008, Graz, Austria, Conference Chairman 2016, , Werkstofftagung TU Graz, (Materials Day), Organizer Member of the Advisory Board, Scientific Committee and Organising Committee for Several National and International conferences CV Peter Mayr Page 5 of 6

6 Reviewing Activities for Scientific Journals Editorial Board Member: Int. J. of Microstructure and Materials Properties (IJMMP) Science and Technology of Welding and Joining (STWJ) Welding in the World (WiW) Reviewer: Int. Journal of Pressure Vessels and Piping Materials Characterization Materials and Design Materials at High Temperature Journal of Materials Processing Technology Materials Science and Engineering A Metallurgical and Materials Transactions A International Journal of Materials Research PROFESSIONAL AFFILIATIONS ASM International AWS - American Welding Society DVS - Deutscher Verband für Schweißen und verwandte Verfahren e.v. MRS - Materials Research Society TMS - The Minerals, Metals and Materials Society VDI - Verein Deutscher Ingenieure ÖGS - Österreichische Gesellschaft für Schweißtechnik WFG - Wissenschaftliche Gesellschaft Fügetechnik Chemnitz, March 2018 CV Peter Mayr Page 6 of 6