Epoxy Resin Specification Information
|
|
- Lynn Bailey
- 6 years ago
- Views:
Transcription
1 Epoxy Resin Specification Information Epoxy Resin products are generally specified in sections and of most equipment specifications. Architectural Specification EPOXY RESIN WORK SURFACES shall be 3/4" (19mm) or 1" (25mm) thick. Work surfaces shall be monolithic and molded from a modified epoxy resin. Work surfaces shall have a smooth non-glare finish. Work surfaces shall be installed with a uniform 1" (25mm) overhang on the front and exposed ends. Work surfaces shall have a continuous drip groove 1/8" (3mm) wide and 1/8" (3mm) on the underside of all exposed edges. All exposed edges shall be finished with a 1/8" (3mm) bevel or a 3/16" (4.7mm) radius. Work surfaces shall be provided in longest practical lengths to minimize joints. BACKSPLASHES shall be of the same material, thickness, and finish as the work surface. Backsplashes are to be supplied loose for field application to assure proper fit of walls. SINKS shall be selected from standard sizes. All rectangular sinks shall be molded in one piece with corners coved and bottom sloped to the outlet. All rectangular sinks shall include modified resin SO-3R 1-1/2" (38mm) outlet, OE-R overflow, and SS-2R stopper. Sinks, outlets and stoppers are to be supplied loose for field application. FUME HOOD TOPS shall be selected from standard sizes. Fume hood tops shall be dished a minimum of 1/4" (6mm) to contain spills unless otherwise specified on architectural drawings. COLOR of work surfaces, sinks, accessories and fume hood tops shall be grey, white or black. Call for a design manual for work surface configurations, thickness, edge finish and sink sizes. Technical Data -- Epoxy Resin Products PHYSICAL PROPERTIES: The following data describes the typical physical properties of epoxy resin products. a) Compressive Strength b) Flexural Strength D695) D790) IMPERIAL S.I. 36,500 psi 252 MPa 16,000 psi 110 MPa
2 c) Tensile Strength d) Density e) Rockwell M Hardness f) Heat Distortion (Temp at 264 psi) g) Thermal Coefficient of Expansion h) Fire Resistance i) Water Absorption HEAT RESISTANCE: D638) D792) D785) D648) D696) D635) D570) 10,500 psi 72 MPa lbs/ft3 1.96g/cm F 176 C x 10-5 in./â F x 10-4 m/â C Self-Extinguishing Self-Extinguishing %.0076% a) A high form porcelain crucible (size: 15 ml. capacity) was heated over a Bunsen burner until the crucible bottom attained a dull, red heat. Immediately the hot crucible was transferred to the epoxy resin work surface and allowed to cool to room temperature. Upon removal of the cooled crucible, there was no effect on the epoxy resin work surface; no blisters, cracks, nor any breakdown of the work surface whatsoever. b) The epoxy resin work surface showed no blistering or cracking when exposed to direct flame. An overturned 3/8" (9.525mm) Bunsen burner, adjusted to quiet flame with a 1-1/2" (38mm) inner cone, was allowed to remain on the work surface for a period of five (5) minutes with no effect. Technical Data -- Epoxy Resin-R Products PHYSICAL PROPERTIES: The following data describes the typical physical properties of epoxy resin-r products. These products are limited to CS-4R, SO- 3R, OE-4R, OE-6R, OE-8R, OE-10R, and OE-S. IMPERIAL S.I. a) Flexural Strength D790) 7,200 psi 29.3 MPa b) Tensile Strength D638) 4,250 psi 49.6 MPa c) Specific Gravity D792) d) Hardness D Scale 70 70
3 Chemical resistance test methods Epoxy Resin Test Results Method A for volatile chemicals. A cotton ball saturated with the test chemical is placed in a one-ounce bottle {10 x 75 mm} test tube or similar container} with a reservoir of liquid above the ball. The container is inverted on the test material surface for a period of 24 hours. Temperature of test 23 +/-2 C (73 + /-4 F) this method was used for the organic solvents. Method B for non-volatile chemicals, five drops (1/4cc) of the test chemical are placed on the test material surface. The chemical is covered with a watch glass (25mm) for a period of 24 hours. Temperature of test 23 +/-2 C (73 + /-4 F). This method was used for all chemicals listed above other than the solvents. Evaluation After 24 hour s exposure, exposed areas are washed with water, then a detergent solution, finally with naphtha, then rinsed with distilled water and dried with a cloth. The sample is then numerically rated as follows: 1. No Effect - No detectable change in color or gloss but no clearly discernable change in function or life of the surface. 2. Excellent - Slight detectable change in color or gloss but no change in function or life of the surface. 3. Good - A clearly discernable change in color or gloss but no significant impairment of surface life or function. 4. Fair - Objectionable change in appearance due to deterioration or etch, possibly resulting in deterioration of function over an extended period of time. 5. Failure - Pitting, cratering or erosion of the surface, obvious and significant deterioration. Inorganic Acids Corrosive Black Platinum Pearl Beige Chromic Acid - 40% Hydrochloric Acid - 10% Hydrochloric Acid - Conc - 37% Nitric Acid - 40% Nitric Acid - Conc - 70% Sulfuric Acid - 60 % Sulfuric Acid - Conc - 96% Organic Acids - Corrosive Acetic Acid - 5% Acetic Acid - Glacial
4 Citric Acid - 1% Oleic Acid Phenol Solution - 5% Alkaline Solutions - Corrosive Ammonium Hydroxide - 10% Sodium Carbonate Sol - 20% Sodium Hydroxide Sol - 60% Sodium Hypochlorite Sol - 4% Organic Solvents Acetone Benzene Carbon Tetrachloride Diethyl Ether Dimethyl Formamide Ethyl Acetate Ethyl Alcohol - 95% Ethylene Dichloride Heptane Isooctane Kerosene Methyl Alcohol Toluene Organic Compounds Aniline Mineral Oil Olive Oil Soap Solution Transformer Oil Turpentine Physical Properties Test Results Physical Test Imperial Metric Compressive Strength ASTM D695 31,400 psi N/mm2 Tensile Strength ASTM D638 8,000 psi 55.2 N/mm2 Flexural Strength ASTM D790 11,700 psi 80.7 N/mm2 Rockwell Hardness M ASTM D Specific Density ASTM D lb/ft gm/cm3 Water Absorption ASTM D % 0.01% Fire Resistance ASTM D635 ATB (sec)=0 AEB (mm)=0 Heat 264 psi ASTM D F 172 C
5 Heat resistance Test Results Test A A porcelain crucible was heated to a dull red color, placed on the test material, and allowed to cool to ambient temperature Observation No surface deformation was observed Test B A 3/8 bunsen burner was adjusted to a quiet flame with a 1 1/2 inner core and overturned on the test material where it stayed for 5 minutes Observation No surface deformation was observed
Work Surface Specification
Work Surface Specification LABORATORY CASEWORK SECTION: 2.6 WORK SURFACES A. Epoxy Resin Work Surface: 2. Materials and Fabrication: a. General: Material shall be a monolithic, filled epoxy resin product
More informationEPOXY Work Surface Specification
2.6 WORK SURFACES Epoxy Resin Work Surface: EPOXY Work Surface Specification Supplier: DURATOP EPOXY Total Lab Solutions Materials and Fabrication: LABORATORY CASEWORK SECTION: General: Material shall
More informationSECTION Epoxy Work Surfaces and Sinks
SECTION 12 3653 - Epoxy Work Surfaces and Sinks PART 1- GENERAL I.I SUMMARY A. This Section includes the following: 1. Epoxy resin countertops and backsplash. 2. Lipped Drop-In epoxy sinks. 3. Under counter
More informationSECTION EPOXY RESIN LABORATORY WORKSURFACES V1.1
SECTION 12 36 53 EPOXY RESIN LABORATORY WORKSURFACES V1.1 PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Epoxy resin [work surfaces] [sinks] [and] [accessories]. 2. Setting materials. B. Related Sections:
More informationCHEMCAST is the only high quality acrylic sheet that can provide you with short runs capability and color selection to fit your specific needs.
INTRODUCTION What makes CHEMCAST acrylic sheet notably different is: CHEMCAST is the only high quality acrylic sheet that can provide you with short runs capability and color selection to fit your specific
More informationINTRODUCTION CHEMCAST PMG ULTRA
INTRODUCTION CHEMCAST PMG ULTRA is a unique high impact, fabricator friendly acrylic sheet with an improved formulation designed to accommodate the needs of the most demanding fabricators and builders.
More informationTECHNICAL SPECIFICATIONS
TECHNICAL SPECIFICATIONS SeamTek Type 4 Epoxy Quartz Flooring System (1/8 ) Section 09700 800-638-9874 www.lspinc.com Part 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract,
More informationTECHNICAL SPECIFICATIONS
TECHNICAL SPECIFICATIONS 800-638-9874 www.lspinc.com Part 1 - GENERAL SeamTek Type 3 Healthcare Epoxy Quartz Flooring System (3/16 ) Section 09700 1.01 RELATED DOCUMENTS A. Drawings and general provisions
More informationTECHNICAL SPECIFICATIONS
Part 1 - GENERAL TECHNICAL SPECIFICATIONS SeamTek Type 3 Epoxy Quartz Flooring System (3/16 ) Section 09700 800-638-9874 www lspinc com 1.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract,
More informationGrilamid TR 55 LY EMS-GRIVORY a unit of EMS-CHEMIE AG
Product Texts Product designation according to ISO 1874: PA 12/MACMI + PA 12, GHLT, 14-020 Mechanical properties dry / cond Unit Test Standard Tensile Modulus - / 1900 MPa ISO 527-1/-2 Yield stress - /
More informationManufacturers declaration of performance
Trespa International B.V. P.O. Box 110, 6000 AC Weert Wetering 20, 6002 SM Weert, The Netherlands Tel.: 31 (0) 495 458 358, Fax: 31 (0) 495 458 570 www.trespa.com Manufacturers declaration of performance
More informationCERTIFIED PRODUCT PERFORMANCE STANDARDS FOR CULTURED MARBLE LAVATORIES
CERTIFIED PRODUCT PERFORMANCE STANDARDS FOR CULTURED MARBLE LAVATORIES 2.GENERAL REQUIREMENTS 2.1 Materials 2.1.1 Filler Materials. The filler materials shall be of grades suitable to produce the performance
More informationMODULAR PHENOLIC CASEWORK
MODULAR PHENOLIC CASEWORK 1.00 General 1.01 General Conditions A) The General Conditions and Supplementary General Conditions apply to all work in this division. B) Warranty: BMT/Nelson Phenolic Casework
More information4 SPRINGS 6 SPRINGS 8 SPRINGS 10 SPRINGS 12 SPRINGS 14 SPRINGS
Sheet No.: 4.201 Rev. A INSTALLATION OF SPRINGS OF P-SERIES ACTUATOR P 4 SPRINGS 6 SPRINGS 8 SPRINGS SPRING 10 SPRINGS 12 SPRINGS 14 SPRINGS Sheet No.: 4.202 Rev. A INSTALLATION OF SPRINGS OF E-SERIES
More informationSECTION LABORATORY METAL CASEWORK and SECTION Laboratory Work Surfaces
Part 1 - General 1.1 SCOPE SECTION 12345 LABORATORY METAL CASEWORK and SECTION 12 3653 - Laboratory Work Surfaces A. The casework contractor, supplier shall furnish all material in accordance with this
More informationEpoxy Resin Comparison
1 Epoxy Resin Comparison Accept No Substitute! Malaysian Epoxy Resin Work Surfaces 2 Epoxy Resin Comparison Accept No Substitute! Malaysian Epoxy Resin Work Surfaces 3 Epoxy Resin Comparison Accept No
More informationGrilon TSG-30/4 EMS-GRIVORY a unit of EMS-CHEMIE AG
Product Texts Product designation according to ISO 1874: PA 66+PA 6, MHR, 14-100 N, GF30 Mechanical properties dry / cond Unit Test Standard Tensile Modulus 9700 / 6000 MPa ISO 527-1/-2 Stress at break
More informationDuPont Zytel 73G45 BK263
Product Information PRODUCT INFORMATION Common features of Zytel nylon resin include mechanical and physical properties such as high mechanical strength, excellent balance of stiffness and toughness, good
More informationDuPont Delrin 500CL NC010
Product Information PRODUCT INFORMATION Common features of Delrin acetal resins include mechanical and physical properties such as high mechanical strength and rigidity, excellent fatigue and impact resistance,
More informationDuPont Delrin 500P BK602
Product Information PRODUCT INFORMATION Common features of Delrin acetal resins include mechanical and physical properties such as high mechanical strength and rigidity, excellent fatigue and impact resistance,
More informationCharacteristics. Availability. Safety. Weather Resistance. Dimensional Stability. Light Weight. Rigidity. Cold Flow. Strength and Stresses
2 Characteristics Availability Safety Weather Resistance Dimensional Stability Light Weight Rigidity Cold Flow Strength and Stresses ACRYLITE FF acrylic sheet is a continuously manufactured acrylic sheet.
More informationGrilamid TR 55 EMS-GRIVORY a unit of EMS-CHEMIE AG
Product Texts Product designation according to ISO 1874: PA 12/MACMI, GT, 11-020 Mechanical properties dry / cond Unit Test Standard Tensile Modulus 2200 / 2200 MPa ISO 527-1/-2 Yield stress 75 / 75 MPa
More informationDuPont Zytel 8018HS NC010
Product Information PRODUCT INFORMATION Common features of Zytel nylon resin include mechanical and physical properties such as high mechanical strength, excellent balance of stiffness and toughness, good
More informationSuper Erecta Wall Mount Technical Data T10.40 TIM CAMPBELL
Wilkes-Barre, PA 18705 www.metro.com Super Erecta Wall Mount Technical Data T10.40 Finish Temp. Abrasion Chip Res. Nickel Chrome Brite Metroseal II Stainless Designer Very Good Very Good Application
More informationDuPont Delrin 100 BK602
PRODUCT INFORMATION Product Information Common features of Delrin acetal resins include mechanical and physical properties such as high mechanical strength and rigidity, excellent fatigue and impact resistance,
More informationDuPont Delrin 100P NC010
Product Information PRODUCT INFORMATION Common features of Delrin acetal resins include mechanical and physical properties such as high mechanical strength and rigidity, excellent fatigue and impact resistance,
More informationDuPont Delrin 500AL NC010
Product Information PRODUCT INFORMATION Common features of Delrin acetal resins include mechanical and physical properties such as high mechanical strength and rigidity, excellent fatigue and impact resistance,
More informationDuPont Delrin 150 NC010
PRODUCT INFORMATION Product Information Common features of Delrin acetal resins include mechanical and physical properties such as high mechanical strength and rigidity, excellent fatigue and impact resistance,
More informationProfiles in thermoplastics rubber TPeRX
Profiles in thermoplastics rubber TPeRX 30 22 Rubber Technology Edge protectors Available on Stock Sidesight 60 38 38 Elastomer joint with adhesive Colour: yellow Packaging: 10 x 2 meters Reference: F1123
More informationDuPont Zytel 73G15HSL BK363
Product Information PRODUCT INFORMATION Common features of Zytel nylon resin include mechanical and physical properties such as high mechanical strength, excellent balance of stiffness and toughness, good
More informationDuPont Zytel 73G30HSL BK261
Product Information PRODUCT INFORMATION Common features of Zytel nylon resin include mechanical and physical properties such as high mechanical strength, excellent balance of stiffness and toughness, good
More informationDuPont Delrin 100AL NC010
Product Information PRODUCT INFORMATION Common features of Delrin acetal resins include mechanical and physical properties such as high mechanical strength and rigidity, excellent fatigue and impact resistance,
More informationDuPont Minlon IG38C1 BK434
Product Information PRODUCT INFORMATION Common features of Minlon nylon resin include mechanical and physical properties such as high mechanical strength, excellent balance of stiffness /toughness, good
More informationDuPont Zytel 70G33L NC010
Product Information PRODUCT INFORMATION Common features of Zytel nylon resin include mechanical and physical properties such as high mechanical strength, excellent balance of stiffness and toughness, good
More informationDuPont Minlon 10B40 NC010
DuPont Minlon 1040 NC010 Product Information PRODUCT INFORMATION Common features of Minlon nylon resin include mechanical and physical properties such as high mechanical strength, excellent balance of
More informationChemical Resistance and Material Selection Guide for Drum Pumps
esistance and Material Selection Guide for Drum Pumps The information in the following guide lists the corrosion resistance of four materials used in the drum pump outer tubes. Additional wetted materials
More informationMATERIAL DATA SHEET TECHLITE WHITE ACOUSTICAL FOAM
TECHLITE White Acoustical Foam is an open-cell foam made of melamine resin. TECHLITE is manufactured in the form of untrimmed blocks with a thin outer skin. The standard dimensions of the blocks are 2500
More informationDuPont Zytel 73G30L NC010
Product Information PRODUCT INFORMATION Common features of Zytel nylon resin include mechanical and physical properties such as high mechanical strength, excellent balance of stiffness and toughness, good
More informationINTRODUCTION Stonia Stonia Stonia
ITODUCTIO Stonia is a trade mark of hybrid acrylics manufactured in Mexico by Plastiglas. Due to its attributes it allows designers, architects and interior decorators freedom to create comfortable environments
More informationPreferred. Steel, Epoxy Powder Coated. Satisfactory. Limited
Corrosion Resistance We manufactures enclosures from a wide range of materials, offering varying degrees of resistance against chemical corrosion. All materials are affected by corrosion in some manner.
More informationSECTION RESINOUS FLOORING
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 09 67 23 1. Use this section only for NCA projects. 2. Delete // // if not applicable to project. Also delete any other item or paragraph not applicable in the
More informationChemical Resistance and Material Selection Guide for FTI Drum Pumps
esistance and Material Selection Guide for FTI Drum Pumps The information in the following guide lists the corrosion resistance of four materials used in FTI drum pump outer tubes. Additional wetted materials
More informationDuPont Zytel 70G33HS1L BK031
Product Information PRODUCT INFORMATION Common features of Zytel nylon resin include mechanical and physical properties such as high mechanical strength, excellent balance of stiffness and toughness, good
More informationDATA SHEET. Atlas Minerals & Chemicals, Inc. REZKLAD SR MORTAR / REZKLAD SR-C MORTAR. 5-37PI ( ) Supersedes 5-37PI (9-95) PHYSICAL PROPERTIES
Atlas Minerals & Chemicals, Inc. DATA SHEET 5-37PI (3-97 2 ) Supersedes 5-37PI (9-95) REZKLAD SR MORTAR / REZKLAD SR-C MORTAR DESCRIPTION solvent free, high performance, acid and solvent resistant mortars
More informationSOLID SURFACE PRODUCTS SPECIFICATION AND TECHNICAL DATA SHEET
SOLID SURFACE PRODUCTS SPECIFICATION AND TECHNICAL DATA SHEET Product Swanstone Reinforced Solid Surface Products Manufacturer Swan, St. Louis, Missouri with manufacturing facilities in Centralia, Illinois.
More informationDuPont Zytel 70G30L NC010
Product Information PRODUCT INFORMATION Common features of Zytel nylon resin include mechanical and physical properties such as high mechanical strength, excellent balance of stiffness and toughness, good
More informationChemGuard FOR LAB COUNTERTOPS
Technical Bulletin ChemGuard FOR LAB COUNTERTOPS Pionite ChemGuard laminate incorporates the decorative features of high pressure laminate into a durable chemical resistant surfacing material. ChemGuard
More informationSECTION PLASTIC SURFACING
SECTION 06067 PLASTIC SURFACING PART 1 GENERAL 1.1 RELATED DOCUMENTS Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification sections, apply
More informationDuPont Hytrel 4068FG (Preliminary Data)
PRODUCT INFORMATION DuPont Hytrel 4068FG (Preliminary Data) Product Information Common features of Hytrel thermoplastic polyester elastomer include mechanical and physical properties such as exceptional
More informationDuPont Zytel 103FHS NC010
Product Information PRODUCT INFORMATION Common features of Zytel nylon resin include mechanical and physical properties such as high mechanical strength, excellent balance of stiffness and toughness, good
More informationO wner s Manual. The Rabbit TM Multiple Gradient Caster Models P7-CST, P1-CST, and P2-CST
O wner s Manual The Rabbit TM Multiple Gradient Caster Models P7-CST, P1-CST, and P2-CST Manual No.: P7,1,2,0602 Rev. Date: 11/2002 Table of Contents Rabbit Multiple Gradient Caster System Safety Information....
More informationINTRODUCTION. 1 GENERAL PRACTICES. 3 I. 3 II. 4 III. 5 IV. 6 V. 9 VI. 9 VII. 10 VIII. 11 IX. 15 X. 15 XI. 18 XII. 18 XIII. 19 XIV. 22 XV. 23 XVI.
INTRODUCTION... 1 GENERAL PRACTICES... 3 I. Drawing Requirements... 3 II. Colors... 4 III. Edges... 5 IV. Surfaces... 6 V. Thickness... 9 VI. Joints... 9 VII. Cutouts... 10 VIII. Curbs (Backsplashes)...
More informationDuPont Zytel 70G43L NC010
Product Information PRODUCT INFORMATION Common features of Zytel nylon resin include mechanical and physical properties such as high mechanical strength, excellent balance of stiffness and toughness, good
More informationPolystone G (HDPE) Polystone P (Polypropylene) Shaping the Future through Innovation.
Polystone G (HDPE) Polystone P (Polypropylene) Shaping the Future through Innovation. Innovation. 11/2011 Competence. Quality. Semi-Finished Thermoplastics Röchling A World Leader in Engineering Plastics
More informationPRODUCT SPECIFICATION
PRODUCT SPECIFICATION Resco s ChemLab is the ultimate laboratory benchtop for high chemical use. The Electro Beam Cured (EBC) surface, gives it an extra stain resistance and high hygiene, making it the
More informationDuPont Zytel 408 NC010A
NLON RESIN PRODUCT INFORMATION Product Information Zytel 408 NC010A is an Unreinforced, Medium Toughened, Polyamide 66 General information Value Unit Test Standard Resin Identification PA66-I - ISO 1043
More informationProperties of standard Bal Spring canted coil spring materials
Custom components that drive tomorrow s technologies. Properties standard Bal Spring canted coil spring materials Technical Report TR-9 (Rev. Q; 10-19-17) (100-44) 19650 Pauling Foothill Ranch, CA USA
More informationFilament wound Plastic Self-lubricating Bearings
Filament wound Plastic Self-lubricating Bearings Filament wound Plastic Self-lubricating Bearings CSB-CRB: Glass fiber epoxy-impregnated with PTFE and high strength fibers CSB-CRG: Glass fiber epoxy-impregnated
More informationDuPont Minlon 73M40 NC010
MINERAL REINFORCED NLON RESIN Product Information PRODUCT INFORMATION Common features of Minlon nylon resin include mechanical and physical properties such as high mechanical strength, excellent balance
More informationPOLIBOX STORE YOUR PERFORMANCE. Technical Datas PPE POLYPROPYLENE FOAM.
Technical Datas PPE POLYPROPYLENE FOAM www.polibox.com POLIBOX ECOLOGY A NEW RESPONSIBILITY ECO-SUSTAINABLE SDS Polibox is one young and dynamics company, been born in order to satisfy all the requirements
More informationScientific Equipment & Furniture Association SEFA Recommended Practices For Laboratory Work Surfaces
Scientific Equipment & Furniture Association SEFA 3-2010 Recommended Practices For Laboratory Work Surfaces SEFA World Headquarters 1205 Franklin Avenue Ste 320 Garden City, NY 11530 Tel: 516-294-5424
More informationPower-Bond CHEMICAL PUMP & DUAL CARTRIDGE PRODUCT DESCRIPTION PRODUCT DESCRIPTION MIXING GUIDELINES POWER-BOND MATERIAL PROPERTIES
184 Power-Bond PUMP & DUAL CARTRIDGE BASE MATERIAL Solid Concrete, Block, Brick, Stone or Masonry SIZE RANGE 3" to Anchor Rod. No. 3 to No. 8 Reinforcing Bar Upon completion of mixing, pull the plunger
More informationHammer-Capsule CHEMICAL PRODUCT DESCRIPTION SUGGESTED SPECIFICATION APPROVALS AND LISTINGS HAMMER CAPSULE SPECIFICATIONS
22 INSTALLATION OF ANCHORS OVERHEAD Prior to installing adhesive anchors overhead or in walls, consult with the governing building authority to determine the requirements for fire safety guidelines. The
More informationDuPont Zytel 70G43L NC010
Product Information PRODUCT INFORMATION Common features of Zytel nylon resin include mechanical and physical properties such as high mechanical strength, excellent balance of stiffness and toughness, good
More informationSURFACE VEIL CONTINUOUS GLASS ROVING. Color
Pultruded Fiberglass Grating Pultrusion technology is a manufacturing process which produces uniform cross-sectionally shaped glassfiber reinforced polymer composite profiles. These profiles are designed
More informationchroma Product Description
Product Description 3form Chroma is produced from optical grade engineered resin. Chroma is available in thick-gauge formats which lends itself well for use in many horizontal applications. Chroma is a
More informationDuPont Delrin 100 NC010
PRODUCT INFORMATION Product Information Common features of Delrin acetal resins include mechanical and physical properties such as high mechanical strength and rigidity, excellent fatigue and impact resistance,
More informationINTRODUCTION APPLICATIONS BENEFITS
ITODUCTIO Stonia is a trade mark of hybrid acrylics manufactured in Mexico by Plastiglas. Due to its attributes it allows designers, architects and interior decorators freedom to create comfortable environments
More informationDuPont Hytrel DYM350BK
THERMOPLASTIC POLESTER ELASTOMER Product Information PRODUCT INFORMATION Common features of Hytrel thermoplastic polyester elastomer include mechanical and physical properties such as exceptional toughness
More informationSeries FBE-4 Type Phenolic Epoxy Powders Fusion Bonded Epoxy. General Description: Powder Feature: Particle Size Distribution (% undersize):
General Description: FBE- Type Phenolic Epoxy FBE- pure primer epoxy powders are based on epoxy (Novolac) and phenolic resins. FBE- pure epoxy powder creates a coating with outstanding adhesion to metal,
More informationLIGHTBLOCKS BOARD. stress cracking. chemical
e info@ chemical stress cracking LIGHTBLOCKS BOARD Contents This brochure provides a summary of the chemical behavior of our semifinished product groups by listing the chemical substances ed on these materials
More informationDuPont Zytel 70G30HSLR BK099
Product Information PRODUCT INFORMATION Common features of Zytel nylon resin include mechanical and physical properties such as high mechanical strength, excellent balance of stiffness and toughness, good
More informationDuPont Zytel 101L NC010
PRODUCT INFORMATION Product Information Common features of Zytel nylon resin include mechanical and physical properties such as high mechanical strength, excellent balance of stiffness and toughness, good
More informationSPECIFICATIONS PVC MANHOLE SYSTEM: FIBERGLASS REINFORCED PLASTIC (FRP) MANHOLE LINER. Predl Systems North America Inc.
SPECIFICATIONS PVC MANHOLE SYSTEM: FIBERGLASS REINFORCED PLASTIC (FRP) MANHOLE LINER SPECIFICATIONS PVC MANHOLE SYSTEM: FIBERGLASS REINFORCED PLASTIC (FRP) MANHOLE LINER I. SCOPE OF WORK A. This specification
More information2 AA 720 A13 C12 EA14 F17 EA14 3 AA 720 B13 B33 C12 F17 EA14 4 AA 720 A13 B13 B33 C12 F17 EA14 5 AA 720 A13 B13 B33 C12 F17 EA14
Compound is a 70 durometer black colored high strength EPDM rubber formulated specifically for use in alkalis and acids, with the exception of concentrated sulfuric and nitric acid. It exhibits good resistance
More informationKERAPLAN d TECHNICAL CERAMICS. High quality worktops for laboratory applications
KERAPLAN d TECHNICAL CERAMICS High quality worktops for laboratory applications www.keraplan.com 2-2018/EN p 002 INDEX page 002 Warranty 003 Our mission for perfect laboratory 004 Product details 005 Colors
More informationFlame Retardant Epoxy Encapsulating & Potting Compound 834FRB Technical Data Sheet 834FRB
Encapsulating and Potting Epoxy Description The Flame Retardant Epoxy Encapsulating and Potting Compound is a UL 94V-0 recognized electric grade epoxy in the QMFZ2 category. This two-part, self-extinguishing
More informationDuPont Hytrel HTR4275 BK316
Product Information PRODUCT INFORMATION Common features of Hytrel thermoplastic polyester elastomer include mechanical and physical properties such as exceptional toughness and resilience, high resistance
More information3M Scotchkote Fusion-Bonded Epoxy Coating 6233P
3M Scotchkote Fusion-Bonded Epoxy Coating 6233P Data Sheet July 2015 Handling and Safety Precautions: Read all Health Hazard, Precautionary and First Aid, Material Safety Data Sheet, and/or product label
More informationDuPont Zytel 70G35HSLRA4 BK267
DuPont Zytel 70G35HSLRA4 K267 Product Information PRODUCT INFORMATION Common features of Zytel nylon resin include mechanical and physical properties such as high mechanical strength, excellent balance
More informationFlame Retardant Epoxy Encapsulating & Potting Compound 833FRB Technical Data Sheet 833FRB
Technical Data Sheet Encapsulating and Potting Epoxy Description The Encapsulating and Potting Compound is a UL 94V-0 recognized electric grade epoxy in the QMFZ2 category. This two parts epoxy provides
More informationDesco Mosaic Flooring Specifications
Desco Mosaic Flooring Specifications PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Sections, apply
More informationtechnical information
CHEMICAL RESISTANCE TABLES Version: 19-08-10 ADD Resins and Chemicals (Pty) Ltd Distribute a comprehensive range of unsaturated polyester resins for chemical resistance applications. The resins recommended
More informationCorrosion Resistant Chain Products. Stainless Steel Silver Shield CR Series Nickel-Plated
3 Corrosion Resistant Chain Products Stainless Steel Silver Shield CR Series Nickel-Plated 2 Drives Corrosion and Moisture Resistant Chains Drives, LLC headquartered, with manufacturing facilities in Fulton,
More informationPPH Pressed and Planed Sheet
Product information Product full identity: Polypropylene Homopolymer PPH is light weight (SG 0.91) has improved chemicalresistance, stiffness, improved higher working temperature compared to PPC (0 C to
More informationRYTON (PPS) Chemical Compatibility & Chemical Resistance Chart
RYTON (PPS) Chemical Compatibility & Chemical Resistance Chart Explanation of Footnotes 1. Satisfactory to 72 F (22 C) 2. Satisfactory to 120 F (48 C) Ratings -- Chemical Effect A = Excellent. B = Good
More informationPHYSICAL CHANGE OR CHEMICAL CHANGE?
PHYSICAL CHANGE OR CHEMICAL CHANGE? STUDENT BOOK Chapter 2, page 58 LAB 24 OBSERVATION TOOLBOX Pages 18 19, 32, 39 40 Goal Distinguish between a physical change and a chemical change. Observation criteria
More informationDATA SHEET. Atlas Minerals & Chemicals, Inc. ATLASTACRETE E / ATLASTACRETE E LT. 8-21PI (5-14) Supersedes 8-21PI ( ) PHYSICAL PROPERTIES
Atlas Minerals & Chemicals, Inc. DATA SHEET 8-21PI (5-14) Supersedes 8-21PI (12-02 3 ) ATLASTACRETE E / ATLASTACRETE E LT DESCRIPTION AND TYPICAL USES ATLASTACRETE E and ATLASTACRETE E LT are epoxy resin
More informationFor high performance anodized aluminum identification plates including bar code labels and UID plates. Because durability really matters
For high performance anodized aluminum identification plates including bar code labels and UID plates. Because durability really matters Identification Plates introduction Virtually every new product and
More informationPE300 Profiles Extruded
Product information Product full identity: High Density Polyethylene PE300 is a lightweight (SG 0.96) and strong material that has excellent sliding properties, good chemical resistance, low moisture absorption
More informationDuPont Hytrel 4069 THERMOPLASTIC POLYESTER ELASTOMER PRODUCT INFORMATION. Product Information
Product Information PRODUCT INFORMATION Common features of Hytrel thermoplastic polyester elastomer include mechanical and physical properties such as exceptional toughness and resilience, high resistance
More informationDuPont Zytel 103HSL NC010
NLON RESIN Product Information PRODUCT INFORMATION Common features of Zytel nylon resin include mechanical and physical properties such as high mechanical strength, excellent balance of stiffness and toughness,
More informationAtlas Minerals & Chemicals, Inc. FURATHANE MORTAR. 5-33PI ( ) Supersedes 5-33PI (7-02) PHYSICAL PROPERTIES
Atlas Minerals & Chemicals, Inc. DATA A SHEET 5-33PI (6-03 2 ) Supersedes 5-33PI (7-02) FURATHANE MORTAR DESCRIPTION FURATHANE MORTAR is a 100% carbon filled, specially formulated furan mortar for chemical
More informationDuPont Crastin S600F10 NC010
Product Information PRODUCT INFORMATION Common features of Crastin thermoplastic polyester resin include mechanical and physical properties such as stiffness and toughness, heat resistance, friction and
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 096623 - RESINOUS MATRIX TERRAZZO FLOORING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationLDPE Sheet Extruded. Product information. Applications. This document contains. Product full identity: Properties.
Product information Product full identity: Low Density Polyethylene LDPE is a lightweight material (SG 0.92) with low water absorption and good chemical resistance. LDPE is renowned for its low stiffness
More informationPE300 Sheet Extruded. Product information. Applications. This document contains. Product full identity: Properties.
Product information Product full identity: High Density Polyethylene PE300 is a lightweight (SG 0.96) and strong material that has excellent sliding properties, good chemical resistance, low moisture absorption
More informationPE300 Rod Extruded. Product information. Applications. This document contains. Product full identity: Properties.
Product information Product full identity: High Density Polyethylene PE300 is a lightweight (SG 0.96) and strong material that has excellent sliding properties, good chemical resistance, low moisture absorption
More informationTemperature Sensing Standard Thermowells for Industrial Applications. Velocity Ratings of Wells. View Product
Standard for Industrial Applications Well failures, in most cases, are not due to the effects of pressure and temperature. The calculations necessary to provide adequate strength under given conditions
More information