CDA ASTM ASARCON SAE AMS FEDERAL MILITARY OTHER
|
|
- Peregrine Gray
- 6 years ago
- Views:
Transcription
1 Product Description: Cartridge Brass, 70% Tempers: H01 Quarter Hard, H02 Half Hard, H04 Hard Solids: 3 8" to 2 1 2" OD Hex: 3 8" to 2" OD Rectangles: Consult Mill Standard Lengths: 144" Wrought Wrought Products Typical Uses Architecture Automotive Builders Hardware Consumer Electrical Fasteners Industrial Ordnance Other Plumbing grillwork odometer contacts, heater cores, thermostats, electrical connectors, radiator cores, radiator tube, radiator tanks, tanks locks, push plates, finish hardware, kick plates, decorative hardware, door knobs, hinges snaps, planters, fireplace screens, etched articles, bird cages, coinage, chain links, pen/pencil inserts and clips, syringe parts, watch parts, costume jewelry, buttons, shells, electrical sockets, lamps terminal connectors, flashlight shells, lamp fixtures, reflectors, screw shells pins, rivets, fasteners, grommets, eyelets, screws air pressure conveyer systems, sound proofing equipment, springs, chain, bead chain, tubing for instruments and machines, heat exchangers, pump cylinders, wire screens, pumps, liners, power cylinders ammunition cartridge cases, mechanical housings for lighters, mechanical housings for ammunition, ammunition stencils, washers fittings, bathroom fixtures, plumbing accessories, faucet escutcheons, traps, plumbing brass goods Similar or Equivalent Specification CDA ASTM ASARCON SAE AMS FEDERAL MILITARY OTHER B927 J461 B927M J463 Chemical Composition Cu% Pb% Zn% Fe% Rem Chemical Composition according to ASTM B927/B927M-17 Note: Cu + Sum of Named Elements, 99.7% min. Single values represent maximums.
2 Wrought Products Machinability Copper Alloy UNS No. Machinability Rating Density (lb/cu in at 68 F) Mechanical Properties Mechanical Properties according to ASTM B927/B927M-17: H01 Quarter-Hard Temper SIZE RANGE: OVER ½" DIAMETER TO 1" INCLUSIVE SIZE RANGE: OVER 1" DIAMETER
3 H02 Half-Hard Temper SIZE RANGE: OVER ½" DIAMETER TO 1" INCLUSIVE Wrought Products SIZE RANGE: OVER 1" DIAMETER
4 Wrought Products H04 Hard Temper SIZE RANGE: ½" DIAMETER TO 1" INCLUSIVE SIZE RANGE: OVER 1" TO 2" DIAMETER Physical Properties US Customary Metric Melting Point Liquidus 1750 F 954 C Melting Point Solidus 1680 F 916 C Density lb/in 3 at 68 F 8.53 gm/cm 3 at 20 C Specific Gravity Electrical Conductivity 28% IACS at 68 F MegaSiemens/cm at 20 C Thermal Conductivity 70 Btu ft/(hr ft 2 F) at 68 F W/m at 20 C Coefficient of Thermal Expansion per F ( F) per C ( C) Specific Heat Capacity 0.09 Btu/lb/ F at 68 F J/kg at 293 C Modulas of Elasticity in Tension ksi MPa Modulus of Rigidity 6000 ksi MPa Physical Properties provided by CDA
5 Fabrication Properties Joining Technique Suitability Soldering Excellent Brazing Excellent Oxyacetylene Welding Good Gas Shielded Arc Welding Good Coated Metal Arc Welding Not Recommended Spot Weld Fair Seam Weld Not Recommended Butt Weld Good Capacity for Being Cold Worked Excellent Capacity for Being Hot Formed Fair Fabrication Properties provided by CDA Thermal Properties Treatment Temp./Time - US Temp./Time - SI Stress Temperature Solution Minimum Solution Maximum Solution Time Solution Medium Precipitation Value Precipitation Time Precipitation Medium Annealing Minimum Annealing Maximum Annealing Time Hot Treatment Minimum Hot Treatment Maximum Wrought Products Fabrication Properties provided by CDA
C26000 CuZn30 Industrial Rolled
Alloy Designation EN DIN CEN/TS 13388 (2.265) CW55A JIS C 26 BS CZ 16 UNS C26 (Cartridge brass, 7%) Brass Rolled Products KME offers a wide range of brass rolled products in the form of strips, sheets
More informationC26800 CuZn33 Industrial Rolled
C268 Alloy Designation EN DIN CEN/TS 13388 CW56L JIS C 268 BS CZ 13 UNS Chemical Composition Weight percentage C268 Cu 66.. 68 % Zn Rest % Ni.3 % Sn.1 % Fe.5 % This alloy is in accordance with RoHS 22/96/CE
More informationC27000 CuZn36 Industrial Rolled
C27 Alloy Designation EN DIN CEN/TS 13388 (2.335) CW57L JIS C 27 BS CZ 18 UNS Chemical Composition Weight percentage C27 Cu 63.5.. 65.5 % Zn Rest % Ni.3 % Sn.1 % Fe.5 % This alloy is in accordance with
More informationC26800 CuZn33 Industrial Rolled
Alloy Designation EN DIN CEN/TS 13388 CW56L JIS C 268 BS CZ 13 UNS Chemical Composition percentage C268 Cu 67 % Zn Rest % This alloy is in accordance with RoHS 22/96/CE for electric & electronic equipments
More informationC Chemical Composition. Copper Alloy Data C Tradename: Beryllium Copper. Designation: Active? True. Inactive Date:
Copper Alloy Data C17510 C17510 Tradename: Beryllium Copper Designation: Active? True Inactive Date: US EPA Registered Antimicrobial? True Chemical Composition Element Cu (1,2) Fe Ni Al Be Co Si Min (%)
More informationIntroduction to Copper and Copper Alloys. James Michel Manager, Technical Services Copper Development Association Inc. May 2013
Introduction to Copper and Copper Alloys James Michel Manager, Technical Services Copper Development Association Inc. May 2013 CDA Mission The Copper Development Association, Inc. is a not-for-profit trade
More informationC22000 CuZn10 Industrial Rolled
Alloy Designation EN DIN CEN/TS 13388 JIS BS CW501L Brass Rolled Products UNS Chemical Composition percentage C22000 Cu 90 % Zn Rest % This alloy is in accordance with RoHS 2002/96/CE for electric & electronic
More informationC27200 CuZn37 Industrial Rolled
C272 Alloy Designation EN DIN CEN/TS 13388 (2.321) CW58L JIS C 272 BS CZ 17 UNS C272 Brass Rolled Products KME offers a wide range of brass rolled products in the form of strips, sheets and discs in order
More informationC51100 CuSn4 Industrial Rolled
Alloy Designation Bronze Rolled Products EN DIN CEN/TS 13388 CW45K JIS C 5111 BS PB 11 UNS Chemical Composition Weight percentage Cu C511 Rest Sn 3.5 4.5 % P.3.35 % This alloy is in accordance with RoHS
More informationCOPPER PRODUCTS. 145 COPPER PRODUCTS Half Hard Tellurium Rounds
COPPER PRODUCTS 110 COPPER PRODUCTS Rounds... 12-2 Squares... 12-2 Flats - Square Edge...12-3 thru12-4 Flats - Full Round Edge (FRE)... 12-5 Cold Rolled Sheet... 12-6 110 Quarter Hard Copper Sheet... 12-6
More informationWe manufactures copper & copper based alloys mainly brass / bronzes extrusion & drawn quality rods / bars
EXTRUDED RODS INTRODUCTION` We manufactures copper & copper based alloys mainly brass / bronzes extrusion & drawn quality rods / bars in different shapes like round, hex, square, rectangular & flat. We
More informationAluminum 6061-T6; 6061-T651
Aluminum 606 I -T6; 606 l -T651 Aluminum 6061-T6; 6061-T651 Categories: Metal; Nonferrous Metal; Aluminum Alloy; 6000 Series Aluminum Alloy Material Notes: General 6061 characteristics and uses: Excellent
More informationIndustrial Rolled. High Performance STOL Alloys. Characteristics. Capacity. xx xx xx xx x x. Density 8.93 g/cm³
Alloy Designation High Performance STOL Alloys EN CW 117 C* DIN CEN/TS 13388 UNS * chemical composition of STOL 8 has a higher Sn content up to,2 % We have developed a wide range of high performance alloys
More informationCopper & Copper Alloys CuZn33Pb1.5AlAs (OF 2279)
Copper and Copper Alloys Page 1 of 5 no responsibility is taken for the correctness of this information 04/2014 Cu Zn Pb Sn Fe Mn Ni Al Si As Co Cr Others min. 64.0 Rem. 1.2 - - - - 0.8-0.02 - - - max.
More informationAircraft. Automotive. Electronic. Oil and Gas
4. Industry Applications of Copper Aircraft Heat Exchange Cable Assembly Terminals Couplers and Connectors Valves Automotive Radiators Brake Tubing Brake Lines Air Coolers Tubing for Master Cylinder Electronic
More informationCopper & Copper Alloys CuZn40Pb2 (OF 2357)
Copper and Copper Alloys Page 1 of 6 no responsibility is taken for the correctness of this information 02/2014 Cu Zn Pb Sn Fe Mn Ni Al Si As Co Cr Others min. 57.0 Rem. 1.6 - - - - - - - - - - max. 59.0-2.2
More informationCustom 450 Stainless Steel, UNS S45000
Custom 450 Stainless Steel, UNS S45000 Shaped, Flat, Square, Round, Fine Wire, Plated and Bare Wire Specifications: AMS5763, AMS 5773, AMS 5863, ASTM A 564, ASTM A693, ASTM A 959 Custom 450 Alloy Description
More informationBronze Rolled Products. Characteristics
Alloy Designation Bronze Rolled Products EN DIN CEN/TS 13388 CW453K JIS C 5210 BS PB 104 UNS Chemical Composition Weight percentage Cu C52100 Rest Sn 8 % P 0.1 % This alloy is in accordance with RoHS 2002/96/CE
More informationNickel Based Superalloy Hastelloy B-3 (UNS N10675)
Nickel Based Superalloy Hastelloy B-3 (UNS N10675) Hastelloy B-3 is manufactured for providing excellent resistance to reducing acids at the different content %s and temperature limits. It shows better
More informationHigh Performance Alloys. Characteristics. Stamped parts connectors Relay springs Semiconductor components. Density 8.8 g/cm³
Alloy Designation High Performance Alloys EN CuNi3Si DIN CEN/TS 13388 UNS Chemical Composition percentage Cu Rest % Ni 3 % Si.65 % Mg.15 % This alloy is in accordance with RoHS 22/96/CE for electric &
More informationHigh Performance STOL Alloys. Characteristics. Current Carrying Capacity. Density 8.9 g/cm³. Specific heat capacity J/(g K)
Alloy Designation High Performance STO Alloys EN - DIN CEN/TS 13388 - UNS Chemical Composition percentage Cu Rest % Ni 1.4.. 1.7 % Si 0.2.. 0.35 % Sn 0.02.. 0.3 % Zn 0.20.. 0.7 % Others 0.50 % This alloy
More informationCopper & Copper Alloys CuZn38As (OF 2765)
Copper and Copper Alloys Page 1 of 5 no responsibility is taken for the correctness of this information 04/2014 Cu Zn Pb Sn Fe Mn Ni Al Si As Co Cr Others min. 61.5 Rem. - - - - - - - 0.02 - - - max. 63.5-0.2
More informationNonferrous Metals and Alloys: Production, General Properties, and Applications
Nonferrous Metals and Alloys: Production, General Properties, and Applications Manufacturing Engineering and Technology 2001 Prentice-Hall Page 6-1 Approximate Cost per Unit Volume for Wrought Metals and
More informationHastelloy C-2000 (UNS N06200)
Hastelloy C-2000 (UNS N06200) Hastelloy C-2000 is a versatile alloy that provides high resistance to variety of chemicals including sulfuric acid, hydrochloric acid and other strong acidic media. It offers
More informationIndustrial Rolled. High Performance STOL Alloys. Characteristics. Capacity. Density 8.8 g/cm³. Thermal expansion coefficient C 17.
Alloy Designation High Performance STOL Alloys EN DIN CEN/TS 13388 UNS Chemical Composition Weight percentage Cu 99. % Mg.4...9 % P.2...4 % This alloy is in accordance with RoHS 22/96/CE for electric &
More informationCopper & Copper Alloys CuZn38Pb2 (OF 2361)
Copper and Copper Alloys Heiligenstraße 70 41751 Viersen Phone +49 2162 956-6 FAX +49 2162 956-762 duelken@otto-fuchs.com Page 1 of 5 no responsibility is taken for the correctness of this information
More informationCuSn0,15 (STOL 81) C14415 Industrial Rolled
Alloy Designation EN DIN CEN/TS 13388 CuSn,15 CW 117 C High Performance CuSn,15 UNS * * Slight difference in chem. composition We have developed a wide range of high performance alloys with excellent properties
More informationCopper & Copper Alloys
Copper and Copper Alloys Page 1 of 6 No responsibility is taken for the correctness of this information 12/2016 Cu Zn Pb Sn Fe Mn Ni Al Si As Co Cr Others min. 58 Rem. - 0.1 0.35 1.8-1.4 0.6 - - - - max.
More informationStainless Steel 310/310S (UNS S31000/ UNS S31008)
Stainless Steel 310/310S (UNS S31000/ UNS S31008) Austenitic Stainless Steel 310/310S offers excellent resistance to oxidation up to 2000oF. It is a low grade steel that prevents embrittlement and sensitization.
More informationThyssenKrupp Materials NA
Copper & Alloys COPPER BRASS BRONZE BEARING BRONZE LEADED BRONZE PHOSPHOR BRONZE MANGANESE BRONZE ALUMINUM BRONZE SILICON BRONZE NICKEL SILVER A ThyssenKrupp Services company ThyssenKrupp Materials NA
More informationStandard Properties of Typical Brass, Bronze, & Aluminum Alloys visit us online at
Standard Properties of Typical Brass, Bronze, & Aluminum Alloys 630 East Green Street Bensenville, IL 60106 Tel: 630.766.3112 Fax: 630.766.3307 630 East Green Street Bensenville, IL 60106 Tel: 630.766.3112
More informationCopper & Copper Alloys CuNi1Si (OF 2403)
Copper and Copper Alloys Page 1 of 5 no responsibility is taken for the correctness of this information 04/2014 Cu Zn Pb Sn Fe Mn Ni Al Si As Co Cr Others Min. Rem. - - - - - 1.0-0.4 - - - - Max. - - 0.02-0.2
More informationHigh Performance Alloys. Characteristics
Alloy Designation EN DIN CEN/TS 13388 UNS High Performance Alloys Chemical Composition Weight percentage We have developed a wide range of high performance alloys with excellent properties regarding conductivity,
More informationCopper & Copper Alloys CuZn37Mn3Al2Si (OF 2291)
Copper and Copper Alloys Page 1 of 5 No responsibility is taken for the correctness of this information 05/2014 Cu Zn Pb Sn Fe Mn Ni Al Si As Co Cr Others min. 58 Rem. - 0.1 0.35 1.8-1.4 0.6 - - - - max.
More informationENAMELING STEELS PRODUCT DATA BULLETIN
ENAMELING STEELS PRODUCT DATA BULLETIN Appliances Plumbingware Barbecue Grills Architectural AK Steel manufactures three enameled products to meet a variety of porcelain enameling and formability requirements:
More informationCustom 455, UNS S45500
Custom 455, UNS S45500 Shaped, Flat, Square, Round, Fine Wire, Plated and Un-plated Specifications: AMS 5617, AMS 5860, ASTM A313 ASTM A564, ASTM A693 Custom 455 Alloy Description Custom 455 stainless
More informationCopper & Copper Alloys CuZn31Si1 (OF 2270)
Copper and Copper Alloys Page 1 of 5 no responsibility is taken for the correctness of this information 02/2014 Cu Zn Pb Sn Fe Mn Ni Al Si As Co Cr Others min. 66.0 Rem. 0.1 - - - - - 0.7 - - - - max.
More informationStainless Steel & Stainless Steel Fasteners Chemical, Physical and Mechanical Properties
Stainless Steel & Stainless Steel Fasteners Chemical, Physical and Mechanical Properties Stainless steel describes a family of steels highly resistant to tarnishing and rusting that contain at least two
More informationCannot be strengthened (precipitation hardening) Strength can be increased only through cold-work Three main groups : 1xxx, 3xxx and 5xxx series
1. Aluminium (Al) Extremely useful engineering material o has low density (2.70 g/cm3) o good corrosion resistance in most natural environment o non-toxic : suitable for food containers and packaging o
More informationIndustrial Rolled. High Performance STOL Alloys. Characteristics. Capacity. Density 8.8 g/cm³. Thermal expansion coefficient C 17.
Alloy Designation High Performance STOL Alloys EN DIN CEN/TS 13388 UNS Chemical Composition percentage Cu 99. % Mg.4...9 % P.2...4 % This alloy is in accordance with RoHS 22/96/CE for electric & electronic
More informationHigh Performance Alloys. Characteristics
Alloy Designation EN DIN CEN/TS 13388 UNS High Performance Alloys Chemical Composition percentage We have developed a wide range of high performance alloys with excellent properties regarding conductivity,
More informationNiSPAN-C 902 (Alloy 902), UNS N09902
NiSPAN-C 902 (Alloy 902), UNS N09902 AMS 5221, AMS 5223, AMS 5225 Alloy 902 Wire Description Alloy 902is a precipitation hardenable nickel-iron with a controllable thermoplastic coefficient which is the
More information316Ti Stainless Steel, UNS S31635
316Ti Stainless Steel, UNS S31635 Shaped, Flat, Square, Round, Fine Wire, Plated and Un-plated ASTM A240 316Ti Alloy Description Type 316Ti is a titanium stabilized variation of alloy 316. This austenitic
More informationNickel Based Superalloy Incoloy 800 (UNS N08800)
Nickel Based Superalloy Incoloy 800 (UNS N08800) Nickel-Iron-Chromium alloy Incoloy 800 has fine strength and suitable resistance to oxidation and carburization at high temperatures. It offers elevated
More informationAluminum Stock Guide.
For more information call (800) 926-2600 1 Materials Services Copper and Brass Sales Aluminum Stock Guide. 1 New! in this edition of the Aluminum Stock Guide, CBS Part Numbers make ordering easier than
More informationThe following tubing can be supplied from stock, on futures or on a periodic release program which we can design to fit your needs.
The following tubing can be supplied from stock, on futures or on a periodic release program which we can design to fit your needs. I. Seamless Copper and Brass Tubing - as per ASTM and military standards,
More informationIdentification. Type Analysis
Page 1 of 12 Unit Display: English Print Now Custom 455 Stainless E-Mail Datasheet Add to My Materials UNS Number S45500 Identification Type Analysis Carbon 0.05 % Manganese 0.50 % Phosphorus 0.040 % Sulfur
More informationmaterial specifications
METAL sheet / plate AS/NZS 1734 " and aluminium alloys - Flat sheet, coiled sheet and plate" Material Finish 304SS 0.9mm Bright annealed Alloy 5052 H32 Ultimate tensile stress 215 MPa minimum Yield tensile
More informationZINC DIE CASTING ALLOYS
ZINC DIE CASTING ALLOYS Overview Eastern Alloys manufactures the complete range of zinc die casting alloys. ZAMAK alloys were first developed during the 1920's by The New Jersey Zinc Company. The name
More informationUNS:C70250, C70320 EN:CW112C
Rendering date: 2018-02-01 13:53:55 http://conductivity-app.org CuNi3Si UNS:C70250, C70320 EN:CW112C Manufactures list: Diehl Metall Stiftung & CO.KG (http://www.diehlmetall.de) - CuNi3Si (SB26) KM Europa
More informationCharacteristics. Current carrying Capacity. Density 8.85 g/cm³. Thermal expansion coefficient C /K
Alloy Designation STOL 94 High Performance STOL Alloys EN CuNi2,5SiZn DIN CEN/TS 13388 UNS Chemical Composition percentage Cu # Rest % Ni 1... 4. % Si.8.. 1. % Zn max. 2. % Sn max. 1. % Ag max..5 % Mg
More informationSECTION MEDICATION CABINET. 1.1 SUMMARY A. Section Includes: 1. Medication cabinets with self-contained refrigerator and fixtures.
SECTION 12 35 70.21 MEDICATION CABINET SPEC WRITER NOTE: Delete text between // // not applicable to project. Edit remaining text to suit project. PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Medication
More informationMuShield s High Permeability Magnetic Shielding per ASTM A753 Alloy Type 4
MuShield s High Permeability Magnetic Shielding per ASTM A753 Alloy Type 4 Available in coil, sheet, rod, billet, wire, and bar form, MuShield s High Permeability Magnetic Shielding is a soft magnetic
More informationJayant Impex Private Limited
+91-8042909029 Jayant Impex Private Limited https://www.jayantferro.com/ We are among leading trader, importer and Supplier Pipe Fittings & Bars product. The offered range of products is best known for
More informationRA17-4 stainless. Introduction
RA17-4 stainless Introduction RA17-4 is an age-hardening martensitic alloy combining high strength with the corrosion resistance of stainless steel. Hardening is achieved by a short-time, simple lowtemperature
More informationHigh-Performance Metal Strip
High-Performance Metal Strip Automotive Aerospace Electronics Power Generation Oil & Gas Innovative & Advanced Metallurgical Technology Putting Metal Strip Technology to Work for You. For the most alloy
More informationHastelloy G-30 (UNS N06030) Chemical Composition
Hastelloy G-30 (UNS N06030) Hastelloy G-30 is commonly used for providing excellent resistance to chemical conditions. It offers resistance to nitric acid, phosphoric acid, hydrochloric acid and hydrofluoric
More informationATI 201 HP /ATI 201L HP
Stainless Steel: Austenitic (UNS S20100 and S20103) GENERAL PROPERTIES and L austenitic stainless steels belong to the 200 series of Cr-Mn-Ni stainless alloys, which are similar to the 300 series of Cr-Ni
More informationSection 906. STRUCTURAL STEEL
906.01 Section 906. STRUCTURAL STEEL 906.01. General Requirements. Finished rolled shapes must be free from imperfections that affect strength and durability in accordance with ASTM A 6. Rolled shapes
More informationATI 718 ATI 718. Technical Data Sheet. Nickel-Base Superalloy INTRODUCTION FORMS AND CONDITIONS AVAILABLE SPECIFICATIONS. (UNS Designation N07718)
ATI 718 Nickel-Base Superalloy (UNS Designation N07718) INTRODUCTION ATI 718 alloy (N07718) is an austenitic nickel-base superalloy which is used in applications requiring high strength to approximately
More informationLow Lead Copper Rod Alloys
Working With Copper Copper rass ronze Low Lead Copper Rod lloys www.copper.org Working With Copper: Low Lead Copper Rod lloys UNS # Common Name Machining Index (a) Chip Type (b) Cu Pb Zn Sn Fe l C21000
More informationStandard Specification for Brass Rod, Bar, and Shapes 1
Designation: B 2 03 Standard Specification for Brass Rod, Bar, and Shapes This standard is issued under the fixed designation B 2; the number immediately following the designation indicates the year of
More informationDatasheet for Steel Grades Carbon Steel AMS 4924
This page is mainly introduced the AMS 4924 Datasheet, including chemical information,mechanical properties, physical properties, mechanical properties, heat treatment, and Micro structure, etc. It also
More informationNONFERROUS ALLOYS. Copper and Copper Alloys
NONFERROUS ALLOYS 525 NONFERROUS ALLOYS Copper and Copper Alloys Pure copper is a reddish, highly malleable metal, and was one of the first to be found and utilized. Copper and its alloys are widely used
More informationHAYNES 188 alloy. Principal Features
HAYNES 188 alloy Principal Features Excellent High-Temperature Strength and Environment Resistance HAYNES 188 alloy (UNS R30188) is a cobalt-nickel-chromium-tungsten alloy that combines excellent high-temperature
More informationSECTION C. Water Infiltration: Provide manufactured cupolas and dormers that do not allow water infiltration to cupola and dormer interiors.
PART 1 - GENERAL 1.1 SUMMARY A. Section includes the following: 1. Manufactured exterior cupolas. 2. Manufactured dormers. 3. Historical locomotive weather Vane. 1.2 PERFORMANCE REQUIREMENTS A. General:
More informationMechanical Properties - Standard. Standard Mild Steel Studs AWS Type A
General Material Specifications Material Specifications Nelson s studs may be made of one of the following materials, as specified on individual specification sheets. Certificates of chemical analysis
More informationINCOLOY alloy 803. Publication Number SMC-033 Copyright Special Metals Corporation, 2004 (Sept 04)
INCOLOY alloy 83 (UNS S3545), an iron-nickelchromium alloy, is designed for use in petrochemical, chemical and thermal processing applications. The nickel and chromium contents of alloy 83 are higher than
More informationATI 15-7 ATI Technical Data Sheet. Semi-Austenitic Stainless Steel INTRODUCTION
ATI 1-7 Semi-Austenitic Stainless Steel (UNS S1700) INTRODUCTION ATI 1-7 Precipitation Hardening Alloy (S1700, AISI Type 632) is a chromium-nickel-molybdenum-aluminum semi-austenitic precipitation hardening
More informationStandard Specification for Cartridge Brass Sheet, Strip, Plate, Bar, and Disks 1
Designation: B 19 05 Standard Specification for Cartridge Brass Sheet, Strip, Plate, Bar, and Disks 1 This standard is issued under the fixed designation B 19; the number immediately following the designation
More informationNominal Composition. Weight %
HASTELLOY HYBRID-BC1 Principal Features High Resistance to Hydrochloric Acid, Sulfuric Acid, Pitting, and Crevice Corrosion HASTELLOY HYBRID-BC1 (UNS N10362) alloy possesses much higher resistance to hydrochloric
More informationAlloy Conductors. Percon Alloys. Percon HS95: A high strength, high conductivity conductor with 655 N/mm 2 strength and 63% IACS.
ALLOY CONDUCTORS Alloy Conductors RoHS compliant alloy conductors were originally invented by Fisk Alloy. Continuously innovating, we now produce a family of high performance alloy conductors, PERCON.
More informationWelding Processes. Consumable Electrode. Non-Consumable Electrode. High Energy Beam. Fusion Welding Processes. SMAW Shielded Metal Arc Welding
Fusion Consumable Electrode SMAW Shielded Metal Arc Welding GMAW Gas Metal Arc Welding SAW Submerged Arc Welding Non-Consumable Electrode GTAW Gas Tungsten Arc Welding PAW Plasma Arc Welding High Energy
More information30ChGSA Included in 13 standards (CIS Countries)
Standards GOST 10702-78 GOST 11268-76 GOST 12132-66 GOST 21729-76 GOST 23270-89 GOST 4543-71 GOST 8731-74 GOST 8733-87 GOST R 54159-10 TU 14-1-1213-75 TU 14-1-1409-75 TU 14-1-4118-76 TU 14-4-385-73 Steel
More informationDatasheet for Steel Grades Carbon Steel SAE J403
This page is mainly introduced the SAE J403 Datasheet, including chemical information,mechanical properties, physical properties, mechanical properties, heat treatment, and Micro structure, etc. It also
More informationUNIFIED FACILITIES GUIDE SPECIFICATIONS
USACE / NAVFAC / AFCEC / NASA UFGS-10 22 13 (August 2016) Change 1-08/18 --------------------------- Preparing Activity: NAVFAC Superseding UFGS-10 22 13 (August 2010) UNIFIED FACILITIES GUIDE SPECIFICATIONS
More informationATI 601 ATI 601. Technical Data Sheet. Nickel-base Alloy INTRODUCTION PRODUCT FORMS SPECIFICATIONS & CERTIFICATES (UNS N06601)
Nickel-base Alloy (UNS N06601) INTRODUCTION alloy (UNS Designation N06601) is an austenitic nickel-chromium-iron alloy designed for both heat and corrosion resistance. As compared to ATI 600 alloy (UNS
More informationUNIFIED FACILITIES GUIDE SPECIFICATIONS
USACE / NAVFAC / AFCEC / NASA UFGS-10 22 13 (August 2016) --------------------------- Preparing Activity: NAVFAC Superseding UFGS-10 22 13 (August 2010) UNIFIED FACILITIES GUIDE SPECIFICATIONS References
More informationMetallurgy, Alloys, and Applications p. 1 Introduction and Overview p. 3 Major Groups of Copper and Copper Alloys p. 3 Properties of Importance p.
Preface p. vii Metallurgy, Alloys, and Applications p. 1 Introduction and Overview p. 3 Major Groups of Copper and Copper Alloys p. 3 Properties of Importance p. 3 Fabrication Characteristics p. 5 Alloy
More informationSANDVIK 6R44 TUBE AND PIPE, SEAMLESS
SANDVIK 6R44 TUBE AND PIPE, SEAMLESS DATASHEET Sandvik 6R44 is an austenitic, niobium-stabilized stainless chromium-nickel steel for use at temperatures up to 850 C (1560 F). STANDARDS ASTM: TP347, TP347H
More informationHAYNES 25 alloy. Principle Features
HAYNES 25 alloy Principle Features Excellent High-Temperature Strength and Good Oxidation Resistance HAYNES 25 alloy (UNS R30605) is a cobalt-nickel- chromium-tungsten alloy that combines excellent high-temperature
More informationNON FERROUS METAL MESH
WALCOOM Walcoom Corporation "Completion on time within budget, focused team and service, Walcoom is always ready to help." Walcoom offers a large selection of non ferrous metal meshes and also thoughtful
More informationDAIMLERCHRYSLER CORPORATION
DAIMLERCHRYSLER CORPORATION No: MS-8580 Material Standard Date Published: 2003-07-30 Category Code: C-3 Change: G EASL Req.: No RESTRICTED: No WROUGHT ALUMINUM AND ALUMINUM ALLOYS 1.0 GENERAL 1.1 Purpose
More informationCORROSION-RESISTANT ALLOYS
CORROSION-RESISTANT ALLOYS HASTELLOY B-3 alloy A nickel-molybdenum alloy with outstanding resistance to hydrochloric and sulfuric acids in the as-welded condition and excellent thermal stability. Contents
More informationSANDVIK 3R65 TUBE AND PIPE, SEAMLESS
SANDVIK 3R65 TUBE AND PIPE, SEAMLESS DATASHEET Sandvik 3R65 is a molybdenum-alloyed austenitic stainless chromium-nickel steel with a low carbon content. STANDARDS ASTM: TP316L, TP316 UNS: S31603, S31600
More information15-5 PH STAINLESS STEEL
Aerospace Chemical Food Processing Metalworking Paper Industries AK STEEL offers a combination of high strength and hardness, good corrosion resistance plus excellent transverse mechanical properties.
More informationSpecifications. TABLE - 1 Wrought alloys : Chemical composition limits (per cent)
Specifications TABLE - 1 Wrought alloys : Chemical composition limits (per cent) Equivalent Copper Magnesium Silicon Iron Manganese * Others Remarks (ISS) alloy (AA) (Total) Old New U.S.A. Min. Max. Min.
More informationESSHETE 1250 TUBE AND PIPE, SEAMLESS
ESSHETE 1250 TUBE AND PIPE, SEAMLESS DATASHEET Esshete 1250 is a fully austenitic chromium-nickel steel with excellent high- temperature strength and good resistance to corrosion in boiler applications.
More informationALUMINUM PRODUCTS. SECTION 1 ROD, BAR AND WIRE (COLD FINISHED) Alloy Descriptions and Applications Mechanical Properties...
ALUMINUM PRODUCTS SECTION 1 ROD, BAR AND WIRE (COLD FINISHED) Alloy Descriptions and Applications...10-4 Mechanical Properties... 10-5 thru 10-6 SIZE CHARTS 2011-T3 Rounds...10-7 2011-T3 Hexagons...10-8
More informationCopper and Copper Alloy Tube, Pipe and Fittings COPPER and COPPER ALLOY TUBE and PIPE Seamless Copper Pipe: Copper pipe is almost pure copper manufactured to the requirements of ASTM B 42 - Standard Specification
More informationTypes : HYDRAULIC TUBE HORN TUBE CAPILLARY TUBE
Inconel alloys are oxidation and corrosion resistant materials well suited for service in extreme environments. It is common in gas turbine blades, seals, and combustors, as well as turbocharger rotors
More informationSECTION COILING COUNTER DOORS
SECTION 08 33 13 COILING COUNTER DOORS SPEC WRITER NOTES: 1. Delete text between // // not applicable to project. Edit remaining text to suit project. 2. Use overhead coiling counter shutters as closures
More informationNominal Composition. Weight % Nickel: 58 Balance Cobalt: 13.5 Iron:
HAYNES Waspaloy alloy Principle Features HAYNES Waspaloy alloy (UNS N07001) is an age-hardenable, nickel-based superalloy with very good strength at temperatures up to about 1800 F (980 C). It is widely
More informationAppendix A British and ISO standards related to welding and aluminium
Appendix A British and ISO standards related to welding and aluminium Listed below are all of the European and ISO standards that are related to the properties, composition and product forms of aluminium
More informationSANDVIK 254 SMO TUBE AND PIPE, SEAMLESS
SANDVIK 254 SMO TUBE AND PIPE, SEAMLESS DATASHEET Sandvik 254 SMO is a high-alloy austenitic stainless steel developed for use in seawater and other aggressive chloride-bearing media. The steel is characterized
More informationSANDVIK 3R12 FOR MEDICAL APPLICATIONS TUBE AND PIPE, SEAMLESS
SANDVIK 3R12 FOR MEDICAL APPLICATIONS TUBE AND PIPE, SEAMLESS DATASHEET Sandvik 3R12 is an austenitic stainless chromium-nickel steel with a low carbon content used for medical and dental instruments.
More informationItem 442 Metal for Structures
Item 442 Metal for Structures 1. DESCRIPTION 2. MATERIALS Provide structural steel, high-strength bolts, forgings, steel castings, iron castings, wrought iron, steel pipe and tubing, aluminum castings
More informationARCAP AP1D AP1D lb/in³ 8.8 g/cm³ 240 Ohm circ mil/ft 40 microohm cm 212 F 572 F 932 F 1112 F 1832 F 100 C 300 C 500 C 600 C 1000 C
Identification VMI No. UNS No. Relevant Specifications Forms Description ARCAP C76350 n/a Strip Wire Bar Sheet Free Cutting bar and wire. Chemical Composition (%) Copper (+Silver) 61 Nominal Nickel (+Cobalt)
More informationT :
Aluminium Stock www.cncdirect.co.nz T : +64 9 622 2169 www.highgrademetals.co.nz About CNC Direct Limited was established by David Thumath in 2007 to supply quality well priced machine tools into the New
More information