STUDY OF INFLUENCE CORROSIVE ENVIRONMENT ON CHARACTERISTICS PROTECTIVE COATINGS USED FOR LONG-TERM CORROSION PROTECTION OF STEEL SUBSTRATE

Size: px
Start display at page:

Download "STUDY OF INFLUENCE CORROSIVE ENVIRONMENT ON CHARACTERISTICS PROTECTIVE COATINGS USED FOR LONG-TERM CORROSION PROTECTION OF STEEL SUBSTRATE"

Transcription

1 STUDY OF INFLUENCE CORROSIVE ENVIRONMENT ON CHARACTERISTICS PROTECTIVE COATINGS USED FOR LONG-TERM CORROSION PROTECTION OF STEEL SUBSTRATE Jitka PODJUKLOVÁ a,kateřina SUCHÁNKOVÁ b, Petr ŠRUBAŘ c,sylvie KOPAŇAKOVÁ d, Kamila HRABOVSKÁ e VŠB TU Ostrava, Ostrava, Čzech Republic, EU a jitka.podjuklova@vsb.cz, b katerina.suchankova@vsb.cz, c petr.srubar@vsb.cz, sylvie.kopanakova@vsb.cz, e kamila.hrabovska@vsb.cz Abstract Corrosive environment has a major impact on the life of steel structures (bridge structures, production shops, look-out towers, etc.), which constitute an integral part of civil engineering. The basic building material for these structures in most cases is steel, which unfortunately gradually degrades in contact with the surrounding atmosphere. This negative phenomenon can be avoided by the application of corrosion protection, most frequently by organic coatings. They are an indispensable part of surface finishes and great emphasis is placed on their quality. The choice of the protective coating system depends primarily on the expected or planned lifetime of corrosion protection. If we focus on the long-term corrosion protection, especially of bridge structures, we need to carefully consider the preliminary surface treatment. The most frequently used technology amongst numerous methods of surface pretreatment of bridge structures is blasting, by means of which it is possible to achieve the required surface quality. This means, in addition to cleaning of the surface of the base material, also the achievement of suitable micro-geometry and physical, or physical and chemical properties of the surface. The paper focuses on experimental verification of coating systems intended for application on steel structures with long-term exposure in corrosive environments. Samples blasted to surface preparation degree of Sa 2 with applied coating systems were exposed to artificial salt spray atmosphere and a corrosive solution, which is used for testing by the so-called accelerated immersion test. Following was the evaluation of degradation and adhesion of the tested coating systems. The experiment was concluded by ascertaining of the content of volatile organic compounds in paint matters using gravimetric method. Keywords: coating system, surface finish, steel structure 1. INTRODUCTION Degradation of steel structures can be prevented by protecting the surface of the base material. Quality of the surface finish depends on several basic factors. It is primarily the very surface treatment prior to paint matter application, properties of the paint matter used, the quality of the work performed, and thus compliance with technological and application conditions according to the paint manufacturer. Pretreatment of steel structures is realized mainly by blasting, in which material surface is cleaned from any dirt like scales, rust or other impurities. Blasting must be followed in the shortest period of time possible by the application of corrosion protection itself, since the surface after blasting is responsive and oxide layers are formed with time.

2 2. EXPERIMENTAL MATERIAL The experimental part of the thesis is based on samples of material KOSMALT - E 300T with dimensions 150 x 100 x 3 mm, whose samples were blasted with steel grit. These samples were supplied by VÍTKOVICE POWER ENGINEERING a.s. These are hot-rolled metal sheets, which is suitable for cold pressing. 1 Mechanical properties of steel KOSMALT - E 300T Element C Mn Si P S Al N Ti Content[%] 0,07 0,21 0,03 0,013 0,01 0,042 0,006 0,06 2 Chemical composition of steel KOSMALT - E 300T Yield strengthre [MPa] Tensile strength[mpa] Ductility A 5 [%] 28 Fig.1 Micrograph of the blasted surface (200x magnification, photographed with the NEOPHOT 2 microscope The reference samples were subject to surface roughness measurement according to EN ISO Evaluation of the substrate roughness was performed by means of MitutoyoSurftest SJ 301. The principle of measurement is based on scanning of the surface profile of the underlying material with a diamond stylus tip. The device setting was the following: profile filter λ c = 8 mm; measured length l = 40 mm, number of measurements 10. Arithmetical mean deviation of the considered profile Ra = micron, the highest profile height Rz = micron. Measured values are appropriate for the blasted surface. 3. EXPERIMENTAL COATING SYSTEMS Experimental works were performed with two types of paints REMOPLAST EP ZINK - this is a two-component epoxy primer containing zinc powder mixed with hardener based on polyamide, which is produced by Rembrandtins.r.o. The main property of coating is cathodic protection of steel surfaces, resistance to chemical, mechanical and climatic stress. REMOPLAST HS - KST FAST - is a two component epoxy paint with a high dry matter and low VOC content, which is produced by Rembrandtins.r.o. The paint contains anticorrosion lamellar pigments and is intended for cover applications on steel substrates.

3 3.1. Paint application The paint matters REMOPLAST EP ZINK and REMOPLAST HS - KST FAST were applied using pneumatic spraying under a pressure of 3 bar with output nozzle diameter of 1.8 mm. According to the technical data sheet of REMOPLAST EP ZINK, the substrate was covered with wet film of a thickness of 70 micron and the REMOPLAST HS - KST FAST paint matter was applied in a wet film thickness of 110 micron, the application was performed in two layers. The measured dry film thickness of REMOPLAST EP ZINK coating was on average about 70 micron and that of REMOPLAST HS - KST FAST was on average 230 micron. 4. EXPERIMENTAL TESTS 4.1. Pull-off adhesion test according to ČSN EN ISO Pull-off adhesion test was performed before the exposure of samples to corrosive chamber and after 720 h of exposure. The measured values of of pull-off strength are recorded and compared in the chart No.1. Chart 1 Chart of comparison of reference samples and the samples before and after the corrosion chamber exposure, and before and after the immersion exposure test It is generally stated that the threshold value for assessing the good adhesion of the coating system is 3 Mpa. The chart No. 1 clearly shows that the average pull-off strength in the two coating systems after exposure in corrosive chamber dropped down to the threshold value of 3 Mpa. This decrease could be caused e.g. by residues of blasting media, which manifested only after exposure. The results of characteristic fractures show a very poor adhesion of the priming matter, since in all cases there was a 100% adhesion damage between the substrate and the first applied layer. The results of the pull-off strength after immersion test are similar to the average pull-off strength after the corrosion test. Concurrently there was a decrease in the average pull-off strength below the limit value of 3 MPa in the priming pant matter REMOPLAST EP ZINK, which indicates poor adhesion of the substrate and proves 100% adhesion damage between the substrate and the first applied layer Cross-hatch adhesion test according to ČSN EN ISO Cross-hatch adhesion test was performed before the exposure of samples to corrosive chamber and after 720 h of exposure. The substrate materials with applied REMOPLAST EP ZINK paint matter were subjected to cross-hatch test by a cutting tool with a spacing of 2 mm of the guide template. The guide template spacing in EP REMOPLAST ZINK REMOPLAST + HS - KST FAST system was 3 mm.

4 Chart 2 Chart of comparison of reference samples and the samples before and after the corrosion chamber exposure, and before and after the immersion exposure test The chart 2 clearly implies that after 720 h of exposure in the corrosion chamber the primer REMOPLAST EP ZINK showed average damage of the grid area of more than 5% but less than 15 %. The average damage of the paint matter REMOPLAST EP ZINK + REMOPLAST HS KST FAST, to the grid area exceeded even 65%. The exposure of the sample in the immersion test with EP REMOPLAST ZINK primer did not cause any substantial change in adhesion and the damage to the grid area is within 5 %. However, in the average damage of the grid area in REMOPLAST EP ZINK + REMOPLAST HS KST FAST system exceeded 65% Corrosion test in artificial atmosphere according to ČSN EN ISO 9227 The duration of exposure in corrosion chamber was at most 720 hours. During the test we carried out photographic documentation and evaluation of changes to the coating system in the interval of 0 h, 24 h, 48 h, 96 h, 120 h, 240 h, 720 h 480 h. The evaluation of the degree of blistering was carried out according to ČSN EN ISO , evaluation of the degree of rust-perforation according to ČSN EN ISO and the evaluation of the degree of delamination and corrosion around the section according to ČSN EN ISO Table 3 Evaluation of the coating system REMOPLAST EP ZINK (Des. REZ) and REMOPLAST HS KS FAST(Des. RHK) during the corrosion tests in artificial atmosphere It is evident from the Table No. 3 that coating systems showed a very good corrosion resistance when exposed to corrosive agents in the corrosion chamber. The coating REMOPLAST EP ZINK, showed the first blisters already after 24 h exposure in the corrosion chamber. There was almost an insignificant number of defects resembling blisters of a size of 0.5 to 5 mm, which did not extent under following exposure, and there was no rust penetration.

5 Fig.2 Photos of samples before exposure in corrosion chamber and after 720 h exposure in paint matter REMOPLAST EP ZINK (desig. ZK8) and the samples of paint matter REMOPLAST EP ZINK + REMOPLAST HS KST FAST (desig. MV8) The REMOPLAST EP ZINK + REMOPLAST HS KST FAST system was damaged in the form of the first type of defects (blisters) after 48 h exposure in the corrosion chamber. The amount of defects was very small, almost insignificant, with a size greater than 5 mm. Subsequent exposure caused no further extension defects and rust penetration of the coating Accelerated submersion test according to the ČSN Accelerated submersion test was carried out in three cycles. Each cycle was followed by a visual evaluation. Table 4 EvaluationofthecoatingsystemREMOPLAST EP ZINK (desig. REZ) and REMOPLAST HS KST FAST(Des. RHK)duringthesubmersion test Exposure in a salt bath 0. Cycle 1. Cycle 2. Cycle 3. Cycle Coating System marking Degree of blistering Degree of rusting Delamination/Corrosion along the cut Blistering aroundt he cut REZ 0 (S0) Ri 0 (S0) 0/0 0 (S0) REZ + RHK 0 (S0) Ri 0 (S0) 0/0 0 (S0) REZ 1 (S4) Ri 0 (S0) 0/1 0 (S0) REZ + RHK 0 (S0) Ri 0 (S0) 0/1 0 (S0) REZ 1 (S4) Ri 0 (S0) 1/1 1 (S4) REZ + RHK 1 (S4) Ri 0 (S0) 0/0 0 (S0) REZ 1 (S4) Ri 0 (S0) 1/1 1 (S4) REZ + RHK 1 (S5) Ri 0 (S0) 0/0 0 (S0) Fig 3 Photos of samples before exposure to accelerated submersion test and after the third cycle in the paint matter REMOPLAST EP ZINK (desig.zk3) and the samples of paint matter REMOPLAST EP ZINK + REMOPLAST HS KST FAST (desig.mv3 The primer coating system REMOPLAST EP ZINK showed slightly worse results than the system designated as REMOPLAST EP ZINK + REMOPLAST HS KST FAST. The primer coating system presented a very small, almost insignificant number of defects resembling blisters with a size of 0.5 to 5 mm

6 already after 1 st Cycle of exposure in the submersion test. These defects did not extend and the coating was not penetrated by rust. The REMOPLAST EP ZINK + REMOPLAST HS KST FAST system was damaged in the form of the first type of defects (blisters) after the second cycle of the submersion test. The amount of blistering ranging from 0.5 to 5 mm was almost negligible. Further exposure within the immersion test caused blistering growth over 5 mm. 5. DETERMINATION OF VOLATILE ORGANIC COMPOUNDS USING GRAVIMETRIC METHOD To determine the content of volatile organic compounds we used gravimetric method with time intervals of 15 min, followed by measurement of weight loss of the coating systems during the curing process. This method is used determine the content of volatile organic compounds [g l-1], density [g cm-3] and dry matter [% by wt.] of the coating systems. 6. CONCLUSION Chart 3 Comparison of paint matter evaporation curves The corrosion test in the salt spray artificial atmosphere showed that after 720 hours of exposure the coating systems showed good corrosion resistance, because in the course of the test only a very small, almost insignificant number of defects resembling blisters of the size of 0.5 to 5 mm occurred. From the point of view of adhesion the coating systems showed a significant decrease to the average value of pull-off strength of 3 MPa, the characteristic fracture results indicate very poor adhesion of primer, since in all cases there was a 100% damage to adhesion between the substrate and the first applied layer. The cross-hatch adhesion tests showed a very good performance of the REMOPLAST EP ZINK coating system, where average damage of the grid area was higher than 5% but less than 15%. Submersion test pointed to very similar results, which were achieved after corrosion test in artificial salt spray atmosphere. Pull-off adhesion test pointed to a low value of pull-off strength, as there was a 100% adhesion damage between the substrate and the first layer applied. Cross-hatch adhesion test of the coating system REMOPLAST EP ZINK pointed out a better adhesion (damage to the grid area of up to 5%) than in the REMOPLAST EP ZINK + REMOPLAST HS KST FAST system. Overall, it can be stated that the coating systems showed very good corrosion resistance, but the adhesion decreased with the time o exposure. AKCNOWLEDGEMENTS This contribution was created under the support of the Czech Ministry of Education, Youth and Sport KONTAKT ME

7 LITERATURE [1] ČERNÁ, E. Studium vlivu korozního prostředí na vlastnosti ochranných povlaků. Ostrava, s. Diplomová práce, VŠB-TU Ostrava.Vedoucí diplomové práce doc. Ing. Jitka Podjuklová, Csc.

Product Data Sheet AkzoNobel Powder Coatings Interpon APP 120 (EL140G)

Product Data Sheet AkzoNobel Powder Coatings Interpon APP 120 (EL140G) AkzoNobel Powder Coatings Product Data Sheet AkzoNobel Powder Coatings Interpon APP 120 (EL140G) Product Description Interpon APP 120 is a powder coating primer,totally free of Zinc, that is designed to

More information

Cold trichloroethylene degreasing Film Thickness 70± 10 µm 10 minutes at 170 C (PZ 660 alone) 5 minutes 30 sec. at 220 (Maximum curing conditions)

Cold trichloroethylene degreasing Film Thickness 70± 10 µm 10 minutes at 170 C (PZ 660 alone) 5 minutes 30 sec. at 220 (Maximum curing conditions) Product Datasheet Product Description Powder Properties Test Conditions BU Powder Coatings Interpon PZ 66 Interpon PZ 66 is a powder coating primer containing zinc which is designed to give enhanced corrosion

More information

Technical Data Sheet EPOXY PRIMER 3:1 Anti-corrosion epoxy primer RELATED PRODUCTS. Epoxy primer hardener EPOXY PRIMER HARDENER PROPERTIES

Technical Data Sheet EPOXY PRIMER 3:1 Anti-corrosion epoxy primer RELATED PRODUCTS. Epoxy primer hardener EPOXY PRIMER HARDENER PROPERTIES EPOXY PRIMER 3:1 Anti-corrosion epoxy primer RELATED PRODUCTS EPOXY PRIMER HARDENER Epoxy primer hardener Epoxy thinner PROPERTIES A product designed and dedicated for renovation of classic cars High solid

More information

Axle Surface Coatings IMechE Seminar 2014

Axle Surface Coatings IMechE Seminar 2014 Excellence In All We Do Axle Surface Coatings IMechE Seminar 2014 Page 1 Axle Surface Coatings Alternatives to current UK practices UK axle surface coatings Limitations of UK axle surface coatings Alternative

More information

Technical Bulletin Performance of several Talc Grades in a Water-Borne 2 Pack Epoxy Primer

Technical Bulletin Performance of several Talc Grades in a Water-Borne 2 Pack Epoxy Primer Technical Bulletin 1203 Performance of several Talc Grades in a Water-Borne 2 Pack Epoxy Primer Contents Introduction Summary Experimental structure and preparation of samples Grades tested Assessment

More information

PRODUCT GUIDE: ZINC-RICH COATINGS. Version:

PRODUCT GUIDE: ZINC-RICH COATINGS. Version: PRODUCT GUIDE: ZINC-RICH COATINGS Version: 08.07.17 305 Zinc Rich Epoxy Polyamide Primer Description: 305 is a user friendly zinc-rich epoxy primer formulated for use as a primer under acrylic, epoxy,

More information

Property Test/Standard Description. US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)

Property Test/Standard Description. US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong) Approved 402;2522 1,2 2522 zinc epoxy ^(ValidationDate) 1 Product description This is a two component polyamide cured zinc rich epoxy coating. It is a high zinc dust containing product. It conforms to

More information

Property Test/Standard Description

Property Test/Standard Description Approved 21060;21061 1,2 21060 epoxy ^(ValidationDate) 1 Product description This is a two component polyamine cured epoxy coating. It is a surface tolerant, high solids, high build product. Will continue

More information

Laboratory Testing of Three Above Ground Paint Systems for Canadian Applications

Laboratory Testing of Three Above Ground Paint Systems for Canadian Applications Laboratory Testing of Three Above Ground Paint Systems for Canadian Applications Amal Al-Borno, Mick Brown Charter Coating Service (2000) Ltd. #6, 4604 13 th Street N.E. Calgary, AB, Canada T2E 6P1 Robert

More information

SIGMACAP MASTIC GF. September surface tolerant coating for lower grade of steel preparation

SIGMACAP MASTIC GF. September surface tolerant coating for lower grade of steel preparation 5 pages DESCRIPTION PRINCIPAL CHARACTERISTICS COLOURS AND GLOSS BASIC DATA AT 20 C Mass density Volume solids VOC (supplied) Recommended dry film thickness Theoretical spreading rate Touch dry after Overcoating

More information

DET NORSKE VERITAS TM

DET NORSKE VERITAS TM TM REPORT Ballast tank coating testing of Jotacote F60 on Muki Z 2001 shop primer Jotun AS Report No./DNV Reg No.: 2012-5029 / 13FNOZF-5 Rev 00, 2012-08-17 Table of Contents 1 INTRODUCTION... 1 2 SCOPE

More information

- Aromatic hydrocarbons - Binder 2,67 kg/dm³ (±0,06 Kg/dm³) Solid content - 80% by weight (±2%) - 58% by volume (±2%) according to ASTM D2697

- Aromatic hydrocarbons - Binder 2,67 kg/dm³ (±0,06 Kg/dm³) Solid content - 80% by weight (±2%) - 58% by volume (±2%) according to ASTM D2697 p. 1/6 ZINGA The Film Galvanising System ZINGA is a one pack coating that contains 96% zinc in the dry film and provides cathodic protection of ferrous metals. It can be used as a unique system as an alternative

More information

Property Test/Standard Description

Property Test/Standard Description Approved 29560;29561 1 29560 zinc silicate ^(ValidationDate) 1 Product description This is a two component ceramically reinforced polyamide cured zinc rich epoxy coating. 1:1 mixing ratio for easy use

More information

Tested in accordance with ISO , high expected durability in corrosivity category C5-I. Property Test/Standard Description

Tested in accordance with ISO , high expected durability in corrosivity category C5-I. Property Test/Standard Description Approved 7461;7680 1,2 7680 zinc epoxy ^(ValidationDate) 1 Product description This is a two component polyamide cured zinc rich epoxy coating. It is a high solids, high zinc dust containing product. It

More information

Property Test/Standard Description

Property Test/Standard Description Approved 32222;32223;35142 1 32222 epoxy composite ^(ValidationDate) 1 Product description This is a two component glass flake reinforced epoxy composite coating. It is heat resistant up to 250 C (482

More information

Approval of Powder Coatings Quick Guide

Approval of Powder Coatings Quick Guide 1. Definitions 2. Powder system for approval versus Corrosivity Class achievable The powder supplier can only request an approval for a Coating System Type defined in the table below. (yellow fieds) He

More information

1.4 kg/l (11.4 lb/us gal) Maximum 295 g/kg (Directive 1999/13/EC, SED) Maximum 420 g/l (3.5 lb/gal) 50 to 63 μm (2.0 to 2.

1.4 kg/l (11.4 lb/us gal) Maximum 295 g/kg (Directive 1999/13/EC, SED) Maximum 420 g/l (3.5 lb/gal) 50 to 63 μm (2.0 to 2. DESCRIPTION One-component, heat-resistant silicone acrylic topcoat primarily for the PPG HI-TEMP 1027 primer or the PPG HI-TEMP 222 G primer. PRINCIPAL CHARACTERISTICS Heat-resistant silicone acrylic topcoat

More information

Property Test/Standard Description

Property Test/Standard Description Approved 612;617 1,2 617 epoxy ^(ValidationDate) 1 Product description This is a two component, polyamide cured, high molecular weight epoxy coating. Designed as a primer for new construction. Can be used

More information

Bharat Heavy Electricals Limited Piping Centre Chennai-17. Specification Number Revision Number Sheet Number PC:E:GF: of 7 CONTENTS

Bharat Heavy Electricals Limited Piping Centre Chennai-17. Specification Number Revision Number Sheet Number PC:E:GF: of 7 CONTENTS PC:E:GF:001 00 2 of 7 CONTENTS 1 SCOPE 2 PRODUCT SPECIFICATION 3 SURFACE PREPARATION 4 PRIMING 5 COATING 6 FIELD JOINTING 7 INSPECTION AND TESTING PC:E:GF:001 00 3 of 7 Technical Specification for Glass

More information

Chapter 7 APPROVAL OF COATINGS

Chapter 7 APPROVAL OF COATINGS Chapter 7 APPROVAL OF COATINGS 7.1 Terminology of the process steps In the following figure, the definition of the several preparations and layers is visual: The substrate is always STEEL Before the eventual

More information

1.4 kg/l (11.4 lb/us gal) Maximum 272 g/kg (Directive 1999/13/EC, SED) Maximum 420 g/l (3.5 lb/gal) To 650 C (1200 F) To 538 C (1000 F)

1.4 kg/l (11.4 lb/us gal) Maximum 272 g/kg (Directive 1999/13/EC, SED) Maximum 420 g/l (3.5 lb/gal) To 650 C (1200 F) To 538 C (1000 F) DESCRIPTION One component heat resistant silicone topcoat for use in an elevated temperature coating system, primarily for application over PPG HI-TEMP 1027 primer PRINCIPAL CHARACTERISTICS Heat resistant

More information

Property Test/Standard Description. semi gloss (35-70) Flash point ISO 3679 Method 1 32 C

Property Test/Standard Description. semi gloss (35-70) Flash point ISO 3679 Method 1 32 C Approved 18420;18360 1,2 18420 epoxy ^(ValidationDate) 1 Product description This is a two component amine cured, glass flake reinforced, abrasion resistant epoxy coating. It is a surface tolerant, high

More information

Pre-qualification testing in accordance with NORSOK M-501, Rev. 5, System 1, suitable for exterior exposure in offshore environment, below 120 C.

Pre-qualification testing in accordance with NORSOK M-501, Rev. 5, System 1, suitable for exterior exposure in offshore environment, below 120 C. Approved 402;2521 1,2 2521 zinc epoxy ^(ValidationDate) 1 Product description This is a two component polyamide cured zinc rich epoxy coating. It is a very high zinc dust containing product. It conforms

More information

Corrosion Protection for Fisher Valves

Corrosion Protection for Fisher Valves Corrosion Protection Product Bulletin Corrosion Protection for Fisher Valves Control valves operate in some of the most severely corrosive conditions imaginable. Valves used near or on the sea are constantly

More information

Technical Information Sheet

Technical Information Sheet Introduction: Unprotected steel will corrode in contact with air (atmosphere) and water. Therefore, a number of techniques have been developed to protect steel parts from the effects of corrosion, and

More information

Refer to Substrates & Surface Preparation.

Refer to Substrates & Surface Preparation. SELECTION & SPECIFICATION DATA Generic Type Description Features Color Finish Primer Dry Film Thickness Aliphatic Acrylic Polyurethane Thin film, high gloss finish with exceptional weathering performance

More information

PRODUCT DATA SHEET Sika Unitherm Platinum

PRODUCT DATA SHEET Sika Unitherm Platinum PRODUCT DATA SHEET Solvent free, ultra high build, two pack, modified epoxy resin based, intumescent fire protection coating for internally or externally exposed structural steel. Ideal for in-shop application.

More information

Coating Specifications

Coating Specifications Quadax Series Butterfly Valves Version May 2011 müller co-ax ag Gottfried-Müller-Str. 1 74670 Forchtenberg Germany Tel. +49 7947 828-0 Fax +49 7947 828-11 E-Mail info@co-ax.com Internet www.co-ax.com Table

More information

Material data sheet. EOS MaragingSteel MS1. Description

Material data sheet. EOS MaragingSteel MS1. Description EOS MaragingSteel MS1 EOS MaragingSteel MS1 is a tool steel powder intended for processing on EOS DMLS TM systems. This document provides information and data for parts built using EOS MaragingSteel MS1

More information

Property Test/Standard Description

Property Test/Standard Description Approved 1505;1506 1,2 1505 phenolic/novolac epoxy ^(ValidationDate) 1 Product description This is a two component polyamine cured phenolic/novolac epoxy coating. It is heat resistant up to 205 C (401

More information

Approved. Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method F (29 C) calculated VOC-US/Hong Kong

Approved. Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method F (29 C) calculated VOC-US/Hong Kong Approved 20920;16620 1 20920 epoxy ^(ValidationDate) 1 Product description This is a two component amine cured epoxy coating. It is a fast drying, zinc phosphate pigmented, high solids, high build product.

More information

Author: M Shaw, Sika Limited. Construction. A Guide to the Concrete Repair European Standards BS EN 1504 Series

Author: M Shaw, Sika Limited. Construction. A Guide to the Concrete Repair European Standards BS EN 1504 Series Author: M Shaw, Sika Limited A Guide to the Concrete Repair European Standards BS EN 1504 Series 1 Contents Section Heading Page Introduction 3 1.0 Overview of BS EN 1504 Documents 4 2.0 BS EN 1504 Principles

More information

Measured in accordance with ASTM D 2697.

Measured in accordance with ASTM D 2697. SELECTION & SPECIFICATION DATA Generic Type Description Features Color Finish Primer Service Temperature Solvent Based Inorganic Zinc Ultra-low VOC member of the Carbozinc family with extraordinary corrosion

More information

NEW AIRCRAFT PRETREATMENT & WASH PRIMER SYSTEM. Angel Green Cortec Corporation 4119 White Bear Parkway White Bear Lake, MN

NEW AIRCRAFT PRETREATMENT & WASH PRIMER SYSTEM. Angel Green Cortec Corporation 4119 White Bear Parkway White Bear Lake, MN Paper No. 0 20 NEW AIRCRAFT PRETREATMENT & WASH PRIMER SYSTEM Angel Green Cortec Corporation 4119 White Bear Parkway White Bear Lake, MN 551 agreen@cortecvci.com ABSTRACT Today s Department of Defense

More information

PRIMERS & SURFACE PREPARATION GUIDE

PRIMERS & SURFACE PREPARATION GUIDE PRIMERS & SURFACE PREPARATION GUIDE Era Polymers Primers & Surface Preparation Guide 1 There are three responses when looking at a coated surface yes, no, and WOW! Wow is the one to aim for. Era Polymers

More information

Property Test/Standard Description

Property Test/Standard Description Approved 515;519;527;1549 1,2 515 epoxy mastic ^(ValidationDate) 1 Product description This is a two component polyamine cured epoxy mastic coating. It is a surface tolerant, high solids, high build product.

More information

All hollow metal doors and frames manufactured in North America are produced from the identical base cold rolled steel, which conforms to ASTM A366.

All hollow metal doors and frames manufactured in North America are produced from the identical base cold rolled steel, which conforms to ASTM A366. 1 STEEL All hollow metal doors and frames manufactured in North America are produced from the identical base cold rolled steel, which conforms to ASTM A. The galvanneal process begins in the Hot Strip

More information

SP-100 Equipment Wash SP-110 Tool Cleaner

SP-100 Equipment Wash SP-110 Tool Cleaner DESCRIPTION: ADVANTAGES: USES: APPLICATION: SP-4888 Damp Surface Coating is a two-component epoxy coating developed specifically for application on wet or damp steel surfaces. In addition, it may be applied

More information

Product Index. Coating Thickness. Porosity. Adhesion. Inspection Kit. Surface Profile. Surface Cleanliness. Gloss

Product Index. Coating Thickness. Porosity. Adhesion. Inspection Kit. Surface Profile. Surface Cleanliness. Gloss Paint Test Equipment Price List 2018 Coating Thickness Wet Film Thickness Porosity Adhesion Surface Roughness Surface Cleanliness Climatic Conditions www.paint-test-equipment.com Product Index Coating

More information

PERFORMANCE STANDARD FOR PROTECTIVE COATINGS FOR DEDICATED SEAWATER BALLAST TANKS IN ALL TYPES OF SHIPS AND DOUBLE-SIDE SKIN SPACES OF BULK CARRIERS

PERFORMANCE STANDARD FOR PROTECTIVE COATINGS FOR DEDICATED SEAWATER BALLAST TANKS IN ALL TYPES OF SHIPS AND DOUBLE-SIDE SKIN SPACES OF BULK CARRIERS Page 2 ANNEX PERFORMANCE STANDARD FOR PROTECTIVE COATINGS FOR DEDICATED SEAWATER BALLAST TANKS IN ALL TYPES OF SHIPS AND DOUBLE-SIDE SKIN SPACES OF BULK CARRIERS 1 PURPOSE This Standard provides technical

More information

Refer to Substrates & Surface Preparation.

Refer to Substrates & Surface Preparation. SELECTION & SPECIFICATION DATA Generic Type Description Features Aliphatic Acrylic Polyurethane High gloss finish with exceptional weathering performance characteristics. Used extensively in virtually

More information

ISO INTERNATIONAL STANDARD

ISO INTERNATIONAL STANDARD INTERNATIONAL STANDARD ISO 16276-1 First edition 2007-05-15 Corrosion protection of steel structures by protective paint systems Assessment of, and acceptance criteria for, the adhesion/cohesion (fracture

More information

SP-100 Equipment Wash SP-110 Tool Cleaner SP-120 Internal Storage Lubricant

SP-100 Equipment Wash SP-110 Tool Cleaner SP-120 Internal Storage Lubricant DESCRIPTION: SP-9888 Pipe Lining is based on the latest Zero VOC Novolac Technology. The product cures to a highly cross-linked coating with excellent chemical, solvent and water immersion resistance.

More information

Technical Data Jotamastic 80 MIO

Technical Data Jotamastic 80 MIO Technical Data Jotamastic 80 MIO Product description Jotamastic 80 MIO is a high solids two-pack micaceous iron oxide pigmented, surface-tolerant epoxy mastic coating which can be applied in low film thickness.

More information

Approved. Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method C calculated VOC-US/Hong Kong. US EPA method 24 (tested)

Approved. Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method C calculated VOC-US/Hong Kong. US EPA method 24 (tested) Approved 28780 1,2 28780 acrylic ^(ValidationDate) 2 Product description This is a one component water borne acrylic emulsion coating. It is a versatile, fast drying product for exterior and interior use.

More information

Fine-Tune Your Knowledge On The Metallizing Process

Fine-Tune Your Knowledge On The Metallizing Process Fine-Tune Your Knowledge On The Metallizing Process 1. What is Metallizing? Metallizing is a common term used to describe thermal sprayed metal coatings. For corrosion protection of steel elements, it

More information

Coating Types. Coating Systems. Coating Basics. Why coatings are used Component of coatings Methods of protection Service environment

Coating Types. Coating Systems. Coating Basics. Why coatings are used Component of coatings Methods of protection Service environment Coating Basics Why coatings are used Component of coatings Methods of protection Service environment Coating types Curing mechanism Design characteristics Limitations Suitable Use Coating Systems Coating

More information

Product Data Sheet SERIES 69 - DRYZINC ZINC-RICH PRIMER (69/90500) Typical applications. Features. Finish and Color. TIGER Shield

Product Data Sheet SERIES 69 - DRYZINC ZINC-RICH PRIMER (69/90500) Typical applications. Features. Finish and Color. TIGER Shield Product Data Sheet SERIES 69 - DRYZINC ZINC-RICH PRIMER (69/90500) Epoxy zinc-rich powder coating primer. Part of a two-coat TIGER Shield system. Designed to impart superior corrosion protection to steel

More information

Property Test/Standard Description

Property Test/Standard Description Approved 720 1,2 720 silicone acrylic ^(ValidationDate) 1 Product description This is a one component physically drying silicone acrylic coating. It is heat resistant up to 600 C. Can be used as primer,

More information

MAINCOTE 1100A Emulsion Advanced Resin for Industrial Coatings based on AVANSE Technology Platform

MAINCOTE 1100A Emulsion Advanced Resin for Industrial Coatings based on AVANSE Technology Platform Technical Data Sheet MAINCOTE 1100A Emulsion Advanced Resin for Industrial Coatings based on AVANSE Technology Platform Regional Product Availability Description Key Features Benefits Asia-Pacific MAINCOTE

More information

Normadur 65 HS. Technical Data PROPERTIES AND RECOMMENDED USAGE TECHNICAL DATA

Normadur 65 HS. Technical Data PROPERTIES AND RECOMMENDED USAGE TECHNICAL DATA Technical Data Normadur 65 HS PROPERTIES AND RECOMMENDED USAGE Paint type: NORMADUR 65 HS is a fast drying, flexible polyurethane coating with an aliphatic isocyanate curing agent. NORMADUR 65 HS is high-solid

More information

Failure Analysis for the Economizer Tube of the Waste Heat Boiler

Failure Analysis for the Economizer Tube of the Waste Heat Boiler China Steel Technical Report, No. 22, pp. 53 58, (2009) Tsung-Feng Wu 53 Failure Analysis for the Economizer Tube of the Waste Heat Boiler TSUNG-FENG WU New Materials Research and Development Department

More information

Anticorrosive Coatings

Anticorrosive Coatings Anticorrosive Coatings Joerg Sander 1 Introduction 1.1 Why corrosion-protective coatings 1.2 Literature 2 Corrosion protection coatings 2.1 Principles of function 2.1.1 Electrochemistry of corrosion inhibition

More information

DP4101 / DP4104 / DP4107 HS PRIMER

DP4101 / DP4104 / DP4107 HS PRIMER Description 2-component High Solids primer with 2 methods of application: a. primer surfacer; b. non-sanding primer. Colour: white, medium grey and black. Composition based on a special hydroxy functional

More information

Abcite X45. Technical Data and Application Guide. Product description. Typical applications. Product range. Product certifications.

Abcite X45. Technical Data and Application Guide. Product description. Typical applications. Product range. Product certifications. Product description is a single layer, primer-free, halogen-free, high strength adhesive thermoplastic powder coating which provides excellent and durable corrosion protection to steel and other metals.

More information

Property Test/Standard Description. US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)

Property Test/Standard Description. US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong) Approved 23660 1,2 23660 silicone acrylic ^(ValidationDate) 1 Product description This is a one component physically drying silicone acrylic coating. It is an aluminum pigmented product. It is heat resistant

More information

Experimental Investigation of the Galvanization. Effects on the Properties of. Low Carbon Alloy Steel

Experimental Investigation of the Galvanization. Effects on the Properties of. Low Carbon Alloy Steel Adv. Theor. Appl. Mech., Vol. 5, 2012, no. 5, 225-236 Experimental Investigation of the Galvanization Effects on the Properties of Low Carbon Alloy Steel Ghazi S. Al-Marahleh Department of Mechanical Engineering,

More information

Date of issue: 5 October 2017 Page: 1/6

Date of issue: 5 October 2017 Page: 1/6 Approved 16560;16561;16840 1,2 16560 epoxy mastic ^(ValidationDate) 1 Product description This is a two component polyamine cured epoxy mastic coating. It is a surface tolerant, abrasion resistance, high

More information

SURFACE PREPARATION FOR SYNTHETIC ROPES

SURFACE PREPARATION FOR SYNTHETIC ROPES Published date: June 30, 2005 SURFACE PREPARATION FOR SYNTHETIC ROPES Rust damaged chock typical of crude tankers. The following recommendations can be applied at the shipyard or during vessel operations.

More information

POLYGUARD RD-6 A FAIL SAFE PIPELINE COATING SYSTEM FOR REHABILITATION OR GIRTH WELDS ON CATHODICALLY PROTECTED PIPELINES

POLYGUARD RD-6 A FAIL SAFE PIPELINE COATING SYSTEM FOR REHABILITATION OR GIRTH WELDS ON CATHODICALLY PROTECTED PIPELINES POLYGUARD RD-6 A FAIL SAFE PIPELINE COATING SYSTEM FOR REHABILITATION OR GIRTH WELDS ON CATHODICALLY PROTECTED PIPELINES A large percent of corrosion failures on cathodically protected structures are associated

More information

EOS StainlessSteel 17-4PH

EOS StainlessSteel 17-4PH IndustryLine EOS StainlessSteel 17-4PH EOS StainlessSteel 17-4PH Technical Data Material composition Acc. to standard EOS StainlessSteel 17-4PH is an iron based metal alloy powder intended for processing

More information

Electroplating. Copyright 2016 Industrial Metallurgists, LLC

Electroplating. Copyright 2016 Industrial Metallurgists, LLC Electroplating Northbrook, IL 847.528.3467 www.imetllc.com Copyright 2016 Industrial Metallurgists, LLC Course content 1. Process Steps (75 minutes) 2. Properties, Defects, and Evaluation (60 minutes)

More information

Property Test/Standard Description. semi gloss (35-70) Flash point ISO 3679 Method 1

Property Test/Standard Description. semi gloss (35-70) Flash point ISO 3679 Method 1 2080;2081 1 2080 epoxy VValidationDate). 1 Product description This is a two component polyamide cured epoxy coating. It is a high solids, high build product. Designed as a mid coat in systems for new

More information

Corlar 2.1 PR-P High Solids Productive Epoxy Primer

Corlar 2.1 PR-P High Solids Productive Epoxy Primer Corlar 2.1 PR-P High Solids Productive Epoxy Primer GENERAL DESCRIPTION A high solids, two component, VOC conforming (2.1 lbs./gal.) Low HAPS productive primer based on Axalta modified polyamide epoxy

More information

Table 2: Salt fog exposure testing Epoxy Salt fog exposure

Table 2: Salt fog exposure testing Epoxy Salt fog exposure ALUMINUM PHOSPHATE TECHNOLOGY ANTI-CORROSION APPLICATION DESCRIPTION Worldwide, the direct cost of corrosion is estimated to be more than $1.8T, which amounts to 3-4% of the GDP of industrialized countries.

More information

Corlar 2.1 PR-P High Solids Productive Epoxy Primer For Use With FG-040, FG-041 or FG-042 Activators

Corlar 2.1 PR-P High Solids Productive Epoxy Primer For Use With FG-040, FG-041 or FG-042 Activators Corlar 2.1 PR-P High Solids Productive Epoxy Primer For Use With FG-040, FG-041 or FG-042 Activators GENERAL DESCRIPTION A high solids, two component, high build, VOC conforming (2.1 lbs./gal.) Low HAPS

More information

SUPERIOR PRODUCTS INTERNATIONAL LEAD-BASED PAINT ABATEMENT ENCAPSULATION METHOD THAT ELIMINATES SANDBLASTING FOR STEEL STRUCTURES

SUPERIOR PRODUCTS INTERNATIONAL LEAD-BASED PAINT ABATEMENT ENCAPSULATION METHOD THAT ELIMINATES SANDBLASTING FOR STEEL STRUCTURES SUPERIOR PRODUCTS INTERNATIONAL INTRODUCES A LEAD-BASED PAINT ABATEMENT ENCAPSULATION METHOD THAT ELIMINATES SANDBLASTING FOR STEEL STRUCTURES Superior Products RUST GRIP and ENAMO GRIP Before 1 LEAD-BASED

More information

Ganicin 2.8 ZR-E Zinc-Rich Epoxy Primer

Ganicin 2.8 ZR-E Zinc-Rich Epoxy Primer Ganicin 2.8 ZR-E Zinc-Rich Epoxy Primer GENERAL DESCRIPTION A three-package, VOC conforming (2.8 lbs/gal) low HAPS, zinc-rich epoxy primer based on Axalta epoxy amine technology. The resulting organic

More information

SURFACE PREPARATION BEFORE PAINTING

SURFACE PREPARATION BEFORE PAINTING SURFACE PREPARATION: For any given paint system, surface preparation is the single important factor which would determine its performance. Various surface preparation methods are adopted depending on the

More information

Ganicin 2.8 ZR- U Zinc-Rich Polyurethane Primer

Ganicin 2.8 ZR- U Zinc-Rich Polyurethane Primer Ganicin 2.8 ZR- U Zinc-Rich Polyurethane Primer GENERAL DESCRIPTION A three-package, VOC conforming (2.8 lbs/gal) low HAPS, zinc-rich urethane primer based on Axalta polyurethane technology. The resulting

More information

Material data sheet. EOS NickelAlloy IN625. Description

Material data sheet. EOS NickelAlloy IN625. Description EOS NickelAlloy IN625 EOS NickelAlloy IN625 is a heat and corrosion resistant nickel alloy powder which has been optimized especially for processing on EOSINT M systems. This document provides information

More information

Carboguard 890 PRODUCT DATA SHEET SELECTION & SPECIFICATION DATA. Generic Type. Cycloaliphatic Amine Epoxy

Carboguard 890 PRODUCT DATA SHEET SELECTION & SPECIFICATION DATA. Generic Type. Cycloaliphatic Amine Epoxy SELECTION & SPECIFICATION DATA Generic Type Description Features Color Finish Primer Cycloaliphatic Amine Epoxy Highly chemical resistant epoxy mastic coating with exceptionally versatile uses in all industrial

More information

NextGen Epoxy WB Epoxy System (EPI-REZ Resin 7520-WD-52 and Research Curing Agent RSC-4431)

NextGen Epoxy WB Epoxy System (EPI-REZ Resin 7520-WD-52 and Research Curing Agent RSC-4431) NextGen Epoxy WB Epoxy System (EPI-REZ Resin 7520-WD-52 and Research Curing Agent RSC-4431) 1 Waterborne Coatings Sustainability & Product Innovation We take an integrated business approach to sustainability

More information

two component high build amine adduct cured phenolic epoxy primer

two component high build amine adduct cured phenolic epoxy primer 5 pages Revision of January 2003 DESCRIPTION two component high build amine adduct cured phenolic epoxy primer PRINCIPAL CHARACTERISTICS primer coat in the Sigma Phenguard tank coating system excellent

More information

MINIMIZING POLLUTION FROM CHEMICAL PRETREATMENT PROCESSES

MINIMIZING POLLUTION FROM CHEMICAL PRETREATMENT PROCESSES MINIMIZING POLLUTION FROM CHEMICAL PRETREATMENT PROCESSES Copyright Ron Joseph & Associates, Inc. All rights rwerved. January 1991. part of this publication may be reproduced or distributed in any form

More information

Sikalastic -821 LV is a two part, elastic, crack-bridging, rapid-curing polyurethane membrane. Sikalastic -821 LV is for machine application only.

Sikalastic -821 LV is a two part, elastic, crack-bridging, rapid-curing polyurethane membrane. Sikalastic -821 LV is for machine application only. PRODUCT DATA SHEET Spray applied waterproofing membrane PRODUCT DESCRIPTION Sikalastic -821 LV is a two part, elastic, crack-bridging, rapid-curing polyurethane membrane. Sikalastic -821 LV is for machine

More information

CONCRETE STEPS, HANDRAILS, AND SAFETY RAIL

CONCRETE STEPS, HANDRAILS, AND SAFETY RAIL SUDAS Standard Specifications Division 9 - Site Work and Landscaping Section 9080 - Concrete Steps, Handrails, and Safety Rail CONCRETE STEPS, HANDRAILS, AND SAFETY RAIL PART - GENERAL.0 SECTION INCLUDES

More information

Waterbased Range Protective coating solutions that cover your needs

Waterbased Range Protective coating solutions that cover your needs PROTECTIVE COATINGS SIGMA COATINGS Waterbased Range Protective coating solutions that cover your needs Sigma AquaCover 400 Sigma AquaCover 200 Sigma AquaCover 45 Sigma AquaCover 40 Sigma AquaCover 35 Sigma

More information

PERFORMANCE OF COATINGS OVER WATERJETTED SURFACES J. PETER AULT, P.E. ELZLY TECHNOLOGY CORPORATION

PERFORMANCE OF COATINGS OVER WATERJETTED SURFACES J. PETER AULT, P.E. ELZLY TECHNOLOGY CORPORATION PERFORMANCE OF COATINGS OVER WATERJETTED SURFACES J. PETER AULT, P.E. ELZLY TECHNOLOGY CORPORATION LEARNING OBJECTIVES THIS WEBINAR WILL EXPLORE ISSUES ASSOCIATED WITH WATERJETTING SURFACE PREPARATION

More information

Frank D. Rea Director of Coatings Services / Chief Chemist

Frank D. Rea Director of Coatings Services / Chief Chemist State of the Union Cleaning and Painting Steel Bridges Frank D. Rea Director of Coatings Services / Chief Chemist CURRENT PRACTICES AND MATERIALS LESSONS LEARNED THE LATEST CURRENT PRACTICES AND MATERIALS

More information

SECTION CERAMIC EPOXY LINING DUCTILE IRON PIPE AND FITTINGS

SECTION CERAMIC EPOXY LINING DUCTILE IRON PIPE AND FITTINGS SECTION 02500 CERAMIC EPOXY LINING DUCTILE IRON PIPE AND FITTINGS (As provided by Tnemec Company, Inc.) GENERAL 1.1 SUMMARY 1. This Section includes surface preparation and shop application of Series 431

More information

Thin Film Internal Epoxy Coating for Pipelines

Thin Film Internal Epoxy Coating for Pipelines Technical and professional requirements TR1114, Version 1.01, Valid from 13.11.2003 Validity area: Classification: Open Contents 1 Introduction...3 1.1 Objective...3 1.2 Warrant...3 1.3 Publication and

More information

Special Provision No. 911F04 March 1997

Special Provision No. 911F04 March 1997 COATING STEEL RAILING SYSTEM(S) - Item No. Special Provision No. 911F04 March 1997 Definitions, Elimination of Pre-Start Material Sample, Material Requirements, Operational Constraints, Time Between Surface

More information

Fusion Bonded Epoxy Powders, Liquid Epoxy, and Repairs on Pipelines

Fusion Bonded Epoxy Powders, Liquid Epoxy, and Repairs on Pipelines Fusion Bonded Epoxy Powders, Liquid Epoxy, and Repairs on Pipelines Period 8 Pipeline Coatings Course 2017 1 1 15 March 3M 2017. All Rights Reserved. Today s Agenda 1. Fusion Bonded Epoxy Powders Overview

More information

Aliphatic Acrylic-Polyester Polyurethane

Aliphatic Acrylic-Polyester Polyurethane SELECTION & SPECIFICATION DATA Generic Type Description Features Color Finish Primer Dry Film Thickness Aliphatic Acrylic-Polyester Polyurethane High build, low sheen finish that has excellent resistance

More information

Carla Sofia Jorge dos Reis

Carla Sofia Jorge dos Reis OPTIMISATION OF AN ANTICORROSION COATING PROCESS USING THE CATHODIC ELECTRODEPOSITION METHOD IN THE AUTOMOTIVE INDUSTRY Carla Sofia Jorge dos Reis INSTITUTO SUPERIOR TÉCNICO UNIVERSIDADE TÉCNICA DE LISBOA

More information

Property Test/Standard Description

Property Test/Standard Description Approved 1537 1,2 1537 alkyd ^(ValidationDate) 1 Product description This is a one component oxidatively drying alkyd coating. It is a fast drying, high build, zinc phosphate pigmented product. Can be

More information

STANDARD NO.: Z0254. ECO 13848: Added revision table and standard format. Minor corrections made through out the document.

STANDARD NO.: Z0254. ECO 13848: Added revision table and standard format. Minor corrections made through out the document. PAGE 1 OF 7 APPROVAL FOR RELEASE FOR USE: POSITION: NAME: DATE: POSITION: NAME: Paint Line Mfg Eng J. Pidima 4/9/2012 Mfg Eng Mgr R.Luety 4/9/2012 Quality Mgr J Meyers 4/9/2012 CHANGE CONTROL: REV: DATE:

More information

The Application Guide offers product details and recommended practices for the use of the product.

The Application Guide offers product details and recommended practices for the use of the product. Technical Data Sheet Application Guide Approved 345 1,2 345 alkyd ^(ValidationDate) 1 Product description This is a one component styrene modified oxidatively drying alkyd coating. It is heat resistant

More information

Scotch-Weld Metal Bonder Acrylic Adhesive DP8407NS Gray

Scotch-Weld Metal Bonder Acrylic Adhesive DP8407NS Gray Scotch-Weld Metal Bonder Acrylic Adhesive Preliminary Technical Data Sheet October 2017 Product Description is a high performance, two-part acrylic adhesive that offers excellent shear, peel, and impact

More information

vinyl ester Property Test/Standard Description semi gloss (35-70) Flash point ISO 3679 Method 1 34 C calculated IED (2010/75/EU) (theoretical)

vinyl ester Property Test/Standard Description semi gloss (35-70) Flash point ISO 3679 Method 1 34 C calculated IED (2010/75/EU) (theoretical) Approved 408;21800;21820;21740;21760;21840 1,2 408 ^(ValidationDate) 1 Product description This is a glass flake reinforced coating. It is an ultra high build, extremely chemical resistant and fast curing

More information

The required quality of surface preparation can vary depending on the area of use, expected durability and if applicable, project specification.

The required quality of surface preparation can vary depending on the area of use, expected durability and if applicable, project specification. Technical Data Sheet Application Guide 15560;15561 1 15560 zinc silicate VValidationDate). 1 Product description This is a two component moisture cured inorganic zinc ethyl silicate coating. It is a fast

More information

Material data sheet. EOS MaragingSteel MS1. Description

Material data sheet. EOS MaragingSteel MS1. Description EOS MaragingSteel MS1 EOS MaragingSteel MS1 is a steel powder which has been optimized especially for processing on EOSINT M systems. This document provides information and data for parts built using EOS

More information

Troubleshooting Guide

Troubleshooting Guide Troubleshooting Guide 2016 Edition Contents Aesthetic/Application Defects.......... 3 Wrinkling.......... 3 Slumping / sagging.......... 4 Dry spray.......... 5 Poor hangability.......... 6 Surges..........

More information

This document is a preview generated by EVS

This document is a preview generated by EVS INTERNATIONAL STANDARD ISO 12944-5 Third edition 2018-02 Paints and varnishes Corrosion protection of steel structures by protective paint systems Part 5: Protective paint systems Peintures et vernis Anticorrosion

More information

Comparison of BS and BS EN for steel materials

Comparison of BS and BS EN for steel materials Comparison of BS and BS EN for steel materials Appendix This table only highlights the comparison of BS and BS EN on steel materials, which are relevant to plan approval. Title of BS BS BS EN Title of

More information

Section COATING RESTORATION

Section COATING RESTORATION Sto Corp. 3800 Camp Creek Parkway Building 1400, Suite 120 Atlanta, GA 30331 Tel: 404-346-3666 Toll Free: 1-800-221-2397 Fax: 404-346-3119 www.stocorp.com 80658R StoColor Texture - Coarse Textured Acrylic-Based,

More information

Abcite X60. Technical Data and Application Guide. Product description. Typical applications. Product range. Product certifications.

Abcite X60. Technical Data and Application Guide. Product description. Typical applications. Product range. Product certifications. Product description is a single layer, primer-free, halogen free, high strength adhesive thermoplastic powder coating which provides best in class and highly durable corrosion protection to steel and other

More information

Property Test/Standard Description

Property Test/Standard Description Approved 34642;34643 1 34642 multipolymeric matrix ^(ValidationDate) 1 Product description This is a two component titanium catalyzed inorganic ceramic copolymer. It complies to the generic type Multi

More information