Excellent stability und. ARNO SHORT-Cut -SIS. w w w. a r n o. d e. Introducing SHORT-Cut -SIS for internal groove turning. The new SHORT-Cut holder

Transcription

1 Introducing SHORT-Cut -SIS for internal groove turning New w w w. a r n o. d e The new SHORT-Cut holder with optimum insert clamping. Easy handling and efficient in production. ARNO SHORT-Cut -SIS Excellent stability und cutting performance Innovative tooling for the grooving application. High performance potential due to compact and rigid design Excellent reliability due to the tight clamping of the insert Maximum tool life central coolant supply through the clamp straight onto the insert.

2 AL l Dmin d f S H O R T - C u t Holder >> Dx EB ET Right hand version shown Holder Dmin ET EB AL Designation d l f Dx 29,5 8 3,1 40 SIS R/L ,0 39,5 LOMX ,5 8 3,1 60 SIS R/L ,0 39,5 LOMX ,5 10 3,1 50 SIS R/L ,5 50,5 LOMX ,5 10 3,1 75 SIS R/L ,5 50,5 LOMX ,5 10 4,1 50 SIS R/L ,5 50,5 LOMX ,5 10 4,1 75 SIS R/L ,5 50,5 LOMX ,5 10 4,1 65 SIS R/L ,5 59,0 LOMX ,5 10 4,1 100 SIS R/L ,5 59,0 LOMX Dimensions in mm. The NEW SHORT-Cut excellent stability and cutting performance! Spare parts Holder Screw Locking ring SIS R/L DIN912-M3x KVR25 SIS R/L DIN912-M3x KVR25 SIS R/L DIN912-M4x KVR32 SIS R/L DIN912-M4x KVR32 SIS R/L DIN912-M4x KVR32 SIS R/L DIN912-M4x KVR32 SIS R/L DIN912-M4x KVR40 SIS R/L DIN912-M4x KVR40

3 S H O R T - C u t Cutting data >> ISO Material Brinell hardness HB AM35C Cutting speed Vc [m/min] AK10 (p) Unalloyed steel and cast steel ca. 0,15% C ca. 0,45% C ca. 0,45% C ca. 0,75% C P Low alloyed steel and cast steel ca. 0,75% C High alloyed steel, high alloyed tools teel and cast steel Stainless steel and ferritic / martensitic, M cast steel Stainless steel and cast steel Cast iron martensitic, austenitic and austenitic/ferritic, chilled pearlitic, ferritic K Cast iron with nodular graphite pearlitic, martensitic ferritic pearlitic Malleable cast iron ferritic pearlitic Aluminium alloys, long chipping not heat treatable heat treatable, heat - treated Casted aluminium alloys 12% Si, hardened % Si, heat treatable, hardened 90 N Copper and copper alloys ( brass / bronze ) 12% Si, not heat treatable Lead alloys, Pb > 1% Brass, bronze Aluminium bronze Copper and electrolyte copper Non ferrous materials Duroplastics Re - inforced plastics Hard rubber High temperature resistant alloys Fe-alloyed S Ni- or Co based heat - treated casting heat - treated Titanium alloys, high strength Pure titan Alpha- and Beta- alloys, hardened H Hardened steel Hard cast iron casting Hardened cast iron 55 HRC The data given are only approximate values. It can be necessary to adjust these datas to the individual machining operation

4 S H O R T - C u t >> Standard geometry >> α Designation B ± 0,05 L α R [mm] [mm] [mm] coated AM35C Grades AK10 uncoated CERMET CBN25 brazed PKD LOMX EN LOMX EN 3,1 4, ,2 0,4 AM geometry >> α Designation B ± 0,05 L α R [mm] [mm] [mm] AM35C coated Grades AK10 uncoated CERMET CBN25 brazed PKD LOMX EN-AM LOMX EN-AM LOMX EN-AM LOMX EN-AM 3,1 3,1 4,1 4, ,2 0,4 0,2 0,4

5 S H O R T - C u t Cutting data and Grades >> f v [mm / U] = Feed rate into solid f n [mm / U] = Feed rate for re-grooving f k [mm / U] = Feed rate for copy-turning a p [mm] = Depth of cut Standard geometry sintered grooving insert two cutting edges for grooving and turning with medium to large chip-cross-section strong cutting edge for interrupted cutting and changing chip-cross-sections for a large number of workpiece materials f v f n f k a p max LOMX EN 0,08-0,20 0,2-1,5 LOMX EN 0,10-0,25 0,4-2,0 SHORT-Cut geometry -AM sintered grooving insert two cutting edges for grooving and turning at medium chip-cross-sections special geometry for very soft cutting and low cutting forces machining all steel materials f v f n f k a p max LOMX EN-AM 0,08-0,20 0,2-1,5 LOMX EN-AM 0,10-0,25 0,4-2,0 Coated carbide grades AM35C HC - P35, HC - M30 CVD-multilayer, substrate + TiC + TiCN + TiN coating Machining steel, stainless steel and cast steel, at medium to large chipcross-sections and medium to low cutting speeds under unfavourable machining conditions where good toughness is required. HC - P35 CVD-multilayer coating, substrate + TiN + TiCN + TiN + TiCN Machining of stainless steel at medium chip-cross-sections. For steel and super alloys. The advantage of this coating is the increased wear resistance, improved crater wear resistance and high toughness and safety against cutting edge outbreaks. HC - P40, HC - M35 CVD-multilayer coating, substrate + Al2O3 + TiN Grade with a good combination of wear resistance and toughness for turning steel, stainless steel as well as cast steel at medium chip-crosssections and medium to high cutting speeds. Can also be used under unfavourable machining conditions Special grade for stainless steel (austenitic). HC - P30, HC - M25, HC-K30 CVD-multilayer TiC + TiCN + TiN coating Machining steel, cast steel as well as grey cast iron, at medium to high cutting speeds, medium to large chip-cross-sections and varying depths of cut. Used for finishing and medium roughing. HC - P25, HC - M20, HC - K20 CVD-multilayer Al2O3-coating, substrate + TiC + TiN + Al2O3 Machining of steel, stainless steel, spheroidal cast iron, cast steel and grey cast iron at high cutting speeds under stable machining conditions. Uncoated carbide grades AK10(P) HW - K10 Submicron carbide grade for machining cast materials, light and nonferrous materials, refractory metals, hardened steels up to 55 HRC. In connection with chipbreaker-alu specially suitable for machining Al- and Cu-alloys. HW - P40 Machining of steel, cast steel and austenitic steel, at medium to lower cutting speeds, medium to large chip-cross-sections, also under unfavourable conditions.

6 Tools and inserts for parting and grooving simplex.de SHORT-CUT - SIS Milling cutters and indexable inserts for milling and thread milling Tooling and indexable inserts for turning and threading Drilling tools and indexable inserts for drilling Drillsystem SHARK-Drill Tools and inserts as well solid carbide twist drills High-pressure machine jaw vice Work holding tools w w w. a r n o. d e ARNO WERKZEUGE w w w. a r n o. d e as well as special tooling and tooling packages for lathes and machining centres For further information please ask for our complete catalogue. Please contact us. Karl-Heinz Arnold GmbH. Karlsbader Str. 4. D Ostfildern Fon +49( 0 ) 711 / Fax +49( 0 ) 711 / info@arno.de. ARNO (UK) Limited. Unit 3, Sugnall Business Centre. Sugnall, Eccleshall. Staffordshire. ST21 6NF Phone +44( 0 ) Fax +44( 0 ) sales@arno.de. ARNO Italia S.r.l. Via Fiume Vimercate (Mi) Tel / Fax / info@arno-italia.it.