Distinctive Characteristics

Transcription

1 istinctive Characteristics Choice of long or short toggles in translucent colors combine with bright LEs available in red, amber, and green, plus super bright LEs available in white, green, and blue. Black face nut enhances front panel appearance. Antistatic material used for toggle withstands 20 kilovolts electrostatic discharge. Panel seal, achieved with use of optional exterior o-ring, conforms to IP65 of IEC60529 Standards. Interior o-ring protects contacts from oil, dust, water, and other contaminants. UL94V-0 fl ammability rated for base. High insulating barriers protect against crossover. Terminals are molded in and epoxy sealed to lock out fl ux, dust, and other contaminants. Actual Size

2 General Specifi cations Electrical Capacity (Resistive Load) Power Level (code W): 125V AC or 250V AC or 12V C for silver Logic Level (code G): 0.4VA 28V AC/C maximum for gold (Applicable Range 0.1mA ~ 20mV ~ 28V) Note: See Supplement Index for explanation of operating range. Other Ratings Contact Resistance: 10 milliohms maximum for silver; 20 milliohms maximum for gold Insulation Resistance: 1,000 megohms 500V C ielectric Strength: 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts & case for 1 minute minimum Mechanical Life: 50,000 operations minimum Electrical Life: 25,000 operations minimum for silver; 50,000 operations minimum for gold Static Capability: Withstands 20 kilovolts ES minimum Nominal Operating Force: 1.9N for.689 (17.5mm) toggle; 2.5N for.433 (11.0mm) toggle Angle of Throw: 25 Materials & Finishes Toggle: Housing: Sealing Ring: Base: Movable Contactor: Movable Contacts: Stationary Contact: Lamp Contacts: Power Terminals: Lamp Terminals: Glass fiber reinforced polyamide Nitrile butadiene rubber iallyl phthalate (UL94V-0) Phosphor bronze with silver or gold plating Silver alloy or copper with gold plating Silver plus copper with silver plating or copper with gold plating Beryllium copper with silver plating Copper with silver or gold plating Brass with silver plating Environmental ata Operating Temperature Range: Humidity: Vibration: Shock: 10 C through +55 C (+14 F through +131 F) 90 ~ 95% humidity for C (104 F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 1.75 hours 50G (490m/s 2 ) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Installation Mounting Torque: Soldering Time & Temperature:.98Nm (8.67 lb in) maximum 3 seconds 350 C maximum for manual soldering Standards & Certifications Flammability Standards: UL94V-0 base

3 TYPICAL SWITCH ORERING EXAMPLE TL 2 2 N A W01 6G POLE TOGGLE COLORS HOUSING LE COLORS 2 PT For Bright A Black Bright C Red 5C Red Amber 5 Amber CIRCUIT F Green For Super Bright 5F Green Super Bright 2 ON NONE ON N No Color 6B White 6F Green 6G Blue S TOGGLE LENGTHS.689 (17.5mm) (combines with silver contacts only).433 (11.0mm) (combines with gold contacts only) W01 G01 TERMINALS, CONTACTS & RATINGS Silver 125V AC for.689 (17.5mm) Toggle only Gold 28V AC/C for.433 (11.0mm) Toggle only ESCRIPTION FOR TYPICAL ORERING EXAMPLE TL22NAW016G PT ON-NONE-ON Circuit.689 (17.5mm) Toggle Length; No Color (matte finish of clear material) Blue, Super Bright LE Black Housing Silver Contacts with 6-amp Rating

4 Pole Model POLE & CIRCUIT Toggle Position Connected Terminals Throw & Power/Lamp Schematics own Center Up own Center Up Notes: Terminal numbers are not actually on switch. Lamp circuit is isolated and requires an external power source. P TL22 ON NONE ON 1-2- OPEN 1-2- PT 1 (COM) 2 (+) (-).689 (17.5mm) Combines with Silver Contacts only Material: TOGGLE LENGTHS & COLORS S.433 (11.0mm) (17.5).689 (11.0).433 Combines with Gold Contacts only Material: HOUSING Colors Available for Bright LE C Red Amber F Green Color Available for Super Bright LE No Color (Appearance is matte N finish of clear material) A Black The housing consists of the one-piece bushing/case of glass fiber reinforced polyamide in black color only. The glass fiber reinforced polyamide material used for the housing is UL fl ammability rated 94V-0. CONTACT MATERIALS, RATINGS, & TERMINALS W Silver Contacts Power Level V AC & 250V AC & 12V C G Gold Contacts See Supplement Index for complete explanation of operating range. Logic Level 0.4VA 28V AC/C The.043 x (1.1mm x 2.0mm) oblong hole accommodates one solid 18-gauge wire or two solid or stranded 20-gauge wires. Exopy Seal (1.17) Turret LE Thk = (0.6) (5.0) (3.0) (3.5) (1.1) Typ.043 Solder Lug Thk = (0.8) Typ LE COES & SPECIFICATIONS Electrical specifications are determined at a basic temperature of 25 C. Lamp circuit is independent of switch operation. If the source voltage is greater than rated voltage, a ballast resistor is required. The ballast resistor calculation and more lamp detail are shown in Supplement; see Supplement Index. Attention Electrostatic Sensitive evices Colored Toggles Bright Clear Toggles Super Bright LE Factory Assembled C F B F G Not Available Separately Color Red Amber Green White Green Blue Forward Peak Current I FM 30mA 30mA 50mA 30mA 30mA 30mA Continuous Forward Current I F 20mA 20mA 20mA 20mA 20mA 20mA Forward Voltage V F 2.0V 2.1V 2.27V 3.6V 3.3V 3.4V Reverse Peak Voltage V RM 4V 4V 4V 5V 5V 5V Current Reduction Rate Above 25 C I F 0.32mA/ C 0.32mA/ C 0.50mA/ C 0.50mA/ C 0.40mA/ C 0.40mA/ C Ambient Temperature Range 10 C ~ +55 C 10 C ~ +55 C 5 6

5 I I TYPICAL SWITCH IMENSIONS 17.5mm Toggle (3.5).138 (1.1) x.043 x (0.6) Typ (1.17) Typ 25 (4.7) Typ (13.5) (0.8) Typ L ( ) v I L ( ) vi (4.5).177 (18.0) Sq.709 (2.5).098 (6.0) ia.236 (17.5).689 (10.0).394 (21.0).827 (0.5) Typ (5.0) Typ TL22NAW016G 11.0mm Toggle (3.5).138 (1.1) x.043 x (0.6) Typ (1.17) Typ 25 (4.7) Typ (13.5) (0.8) Typ L ( ) v I L ( ) vi (6.0).236 (18.0) Sq.709 (2.5).098 (11.0).433 (10.0).394 (21.0).827 (0.5) Typ (5.0) Typ TL22SCAG015C STANAR HARWARE OPTIONAL HARWARE AT527MA Black Hex Nut Use as Face Nut Chrome/Steel AT527M Hex Nut Use as Backup Nut Nickel/Steel AT508 Lockwasher Not to use with Panel Seal Steel with Chromate/Zinc AT401P O-ring Use for Panel Seal Natural Rubber (12.1).476 (14.0).551 (14.0).551 (15.8) ia.622 (12.1) ia.476 (17.5) ia.689 (13.8) ia.543 (16.0).630 (16.0).630 (1.0).039 (0.5) (1.5).059 Hardware details in Accessories & Hardware section. Panel Cutouts Maximum Panel Thickness with Standard Hardware.157 (4.0mm) (12.5) ia.492 (1.5).060 (12.5) ia.492 (11.5).453 Maximum Panel Thickness with Standard Hardware & AT401P O-ring.236 (6.0mm)