0.5mm Pitch SMT Board to Board Connector

Transcription

1 .5mm Pitch SMT oard to oard onnector DF16 Series orrespond to Automatic Mounting The vacuum pick-up area is prepared for automatic mounting machine. Features 1. Miniaturizing and Slimming In addition to.5mm pitch miniaturization, board to stacking height of 2mm and 2.5mm are prrovided. Receptacle commonly uses DF16#-*DS-.5V. Header Product Name DF16#(2.)-*DP-.5V DF16#(2.5)-*DP-.5V Stacking Height 2.mm 2.5mm Note1: The stacking height doesn't include the solder paste thickness. 2. High ontact Reliability The bellows female contact has a sufficient spring characteristic despite the low profile, and achieves high contact reliability. 3. lick Sensitivity In Mating The click feeling is considered to facilitate insertion check when the connector is mated. 4. Metal Fitting Available The metal fitting to prevent the solder peel is provided, considering the mounting on FP. 5. orresponding to Automatic Mounting The connector has the vacuum pick-up area, and enables the automatic mounting with the embossed tape packaging. onnector specification with no boss and no fitting is also. Applications Mobile phone, LD(Liquid rystal Display), and so on A38

2 Product Specifications Rating Rated urrent :.3A Operating Temperature Range : 35~+85ç (Note 1.) Storage Temperature Range : 1~+6ç (Note 2.) Rated Voltage : 5V A Operating Humidity Range : 4~8% Storage Humidity Range : 4~7% (Note 2.) Item Specification ondition 1. Insulation Resistance 5Mø min Measured at 1V D 2. Withstand voltage Neither short or insulation breakdown 15V A for 1 minute 3. ontact Resistance 5mø max Measured at 1mA 4. Vibration lectrical discontinuity, 1µ S max. 1~55Hz and single amplitude.75mm in 3 directions for 2 hours, respectively. 5. Moisture Resistance ontact resistance: 5mø max.insulation resistance:25mø min. xposed to temperature 4±2ç and humidity 9~95% for 96 hours 6. Temperature ycle ontact resistance: 5mø max.:insulation resistance: 5Mø min. (-55ç: 3 minutes 5~35ç: 1 minutes (-85ç: 3 minutes 5~35ç: 1 minutes) 5 cycles 7. Operating Life ontact resistance: 5mø 5cycle 8. Resistance to Soldering heat No resion area fusion to degrade performance SMT Type Reflow According to the recommended temperature profile Manual soldering Soldering iron temperature: 3ç for 3 seconds Note 1: Temperature rise included when energized Note 2: This storage indicates a long-term storage state for the unused product before the board mounted. The operating temperature and humidity ranges are applied to the non-energized state after the connector has been installed to the board. Note 3: The above standards represent this series. Individual formal agreement should be based on the "Specification". Material Product Part Material Treatment UL Standard Insulator Polyamide resin White eige (Natural) UL94V- Receptacle ontact Phosphor copper Gold plating Metal fitting rass Solder plating Insulator Polyamide resin White eige (Natural) UL94V- Header ontact Phosphor copper Gold plating Metal fitting rass Solder plating Ordering Information Please determine the specific product. If needed, please select and order products from the product No. as listed on catalog page A31~A315. Receptacle/Header DF 16 # (ππ) - * DS -.5 V (*,*) q w e r t y u i o q Series Name : DF w Series No. : 16 e Type Symbol Symbol Fitting oss None K K A K K r Product height Receptacle : None Header : 2., 2.5 t Number of ontacts 14, 2, 3,, 4, 5, 6, (8) (Note1) y onnector Type DS : Double-row receptacle DP : Double-row header u ontact Pitch :.5mm i ontact Type V : Straight SMT o Pakaging Type (5) : Gold plating, embossed tape packaging (51) : Gold plating, tube packaging Note1: For the 8 contacts connector, the stacking height 2.mm product only is available. For the 14 and contacts connectors, the stacking height of 2.5mm product only is available. A39

3 oard to oard 2.5mm Header With metal fitting P=.5 A Ø.5.65 D [Specific No.] * *, (* *) (5) :Gold plating, tube packaging (51) :Gold plating, embossed tape packaging oard to oard 2.5mm Header With metal fitting, With boss Unit: mm Product No. HRS No. Number of ontacts DF16(2.5)-2DP-.5V(ππ) L ππ DF16(2.5)-3DP-.5V(ππ) L ππ DF16(2.5)-DP-.5V(ππ) L ππ DF16(2.5)-4DP-.5V(ππ) L ππ DF16(2.5)-5DP-.5V(ππ) L ππ DF16(2.5)-6DP-.5V(ππ) L ππ A D Tube Packaging Quantity( pcs.) 59 pcs. 45 pcs. 42 pcs. 37 pcs. 31 pcs. 26 pcs. oard to oard 2.5mm Header With metal fitting, Without boss Unit: mm Product No. HRS No. Number of ontacts DF16(2.5)-2DP-.5V(ππ) L ππ DF16(2.5)-3DP-.5V(ππ) L ππ DF16(2.5)-DP-.5V(ππ) L ππ DF16(2.5)-4DP-.5V(ππ) L ππ DF16(2.5)-5DP-.5V(ππ) L ππ DF16(2.5)-6DP-.5V(ππ) L ππ A D Tube Packaging Quantity( pcs.) 59 pcs. 45 pcs. 42 pcs. 37 pcs. 31 pcs. 26 pcs. A314

4 Recommended P Footprints Receptacle P=.5±.2.25±.2 M N ± ±.3 G±.3 Ø (Note 2) Note1: If the pattern is included in the shaded area, and is not treated with resist, it could touch the connector contact. Note2: If the boss isn't included, the boss hole shown in the above isn't required. Number of ontacts G M N Header (oard to oard 2., 2.5mm) P=.5±.2.25±.2 G +.1 H -.1 ± ± Ø.6 (Note 2) +.5 ±.3 K Note1: If the pattern is included in the shaded area, and is not treated with resist, it could touch the connector contact. Note2: If the boss isn't included, the boss hole shown in the above isn't required. Note3: Don't install any part in the shaded area. If installed, the connectors can't be mated with each other. Number of ontacts G H K A316

5 mbossed arrier Tape Dimensions Receptacle Reel Dimensions Ø ±.1 2±.1 4±.1 L± ± Product name label Ø13±.2 2±.5 Ø21±.8 Ø1.5Lead hole depth M±.1 (Ø8±1) N±.3 Ø33±2 R ±.1 2.2±.15 2±.5 Q +2 R ±.5 Unreeling direction Header Reel Dimensions Ø ±.1 2±.1 4±.1 L± ±.1 Product name label Ø13±.2 2±.5 Ø21±.8 Ø1.5Lead hole depth (Ø8±1) Ø33±2 M±.1 N±.3 2±.5 Q +2 R ±.1 (2.)1.9±.15 (2.5)2.4±.15 R ±.5 Unreeling direction Product Name N M L Q DF16#-14DS-.5V 24. DF16#-2DS-.5V 24. DF16#-3DS-.5V 24. DF16#-DS-.5V 24. DF16#-4DS-.5V 32. DF16#-5DS-.5V 32. DF16#-6DS-.5V 32. DF16#-8DS-.5V DF16#(2.)-14DP-.5V DF16#(2.)-DP-.5V 24. DF16#(2./2.5)-2DP-.5V DF16#(2./2.5)-3DP-.5V 24. DF16#(2./2.5)-4DP-.5V 24. DF16#(2./2.5)-5DP-.5V 24. DF16#(2./2.5)-6DP-.5V 32. DF16#(2./2.5)-8DP-.5V A317

6 Precautions for Use Temperature 25ç 2ç IR reflow condition Preheating area 15ç 3~9 seconds Soldering area 235ç±5ç 1 seconds max. 22ç min. 1~2 seconds Max 24ç 22ç 15ç 1. Recommended Temperature Profile (SMT) 1ç Preheating area Soldering area 5ç ç SS 5SS 1SS 15SS 2SS Time Note1: Maximun twice actions are allowed under the same condition. However, the interval between the first and second actions must be maintained at the room temperature. Note2: The temperature indicates the board surface temperature of the connector lead area. 2. Recommended Manual Soldering ondition (SMT) Soldering iron temperature: 29±1ç, Soldering time: Within 2 seconds 3. Recommended Screen Thickness (SMT) 4. oard Warp (SMT) 5. leaning ondition 6. autions.15mm Maximum.2mm in the connector center area, based on the both connector edges Refer to the "Nylon onnector Instruction Manual". The header is designed in a structure where contacts are exposed. Touching it with bare hands would cause contact failure or electrostatic element damage. Where no board is mounted, the insertion or extraction will cause damage or contact deformation. Avoid retaining the board with the connector only, and fix the board by any other means than the connector. xcessive scoop insertion or extraction may result in damage. In the manual soldering process, don't carry out flux coating which will cause a flux blister on the connector. The color phase of this product may be slightly different from that of the formed product according to the manufacturing lot. However, the difference doesn't affect the performance. A318