alloy (SSTEELE RANGE)

Transcription

1 alloy (SSTEELE RANGE)

2 2 SALIENT FEATURES Direct Injection Single Density PU Sole Upper in Grain leather Barton print Breathable and absorbent CAMBRELLE lining Imported alloy steel toe cap - Max 200 Joules Electrical resistance - Max 18 KV for 1 min Heat resistance - Max 120⁰ C for 1 min Size : Month Sole Warranty

3 3

4 4

5 5

6 6

7 7

8 8 Appearance & Design Design : Low-neck safety shoe designed for maximum safety and comfort Anatomically shaped lasts with curved heel and rounded edges for greater comfort after long periods of wear Upper Height : Less than 103mm (measured from outside without heel height) for all sizes 5-11 as per IS (part1): 2011 / ISO Process Manufactured by Direct Injection Process (DIP) without using nails Acme Fabrik Plast Company, NH-3, Agra Bombay Road, Girwai, Gwalior (MP), India

9 9 Upper Material : Finest genuine grain leather in Barton print Colour : Black Thickness : mm (minimum 1.5mm) Tear strength : 120 Newtons (minimum) as per ISO 3377 Water vapour permeability : Not less then 0.8mg / cm 2 Water vapour coefficient : Not less then 20mg / cm 2 ph value of the upper leather : Not be less than 3.5 if ph is below 4 then differential figure shall be less then 0.7 Acme Fabrik Plast Company, NH-3, Agra Bombay Road, Girwai, Gwalior (MP), India

10 10 Vamp & Quarter lining Vamp lining material : 250 gsm non woven fabric Tear strength : 15 Newtons (minimum) Abrasion resistance : Dry Condition no hole before cycles Wet Condition no hole before cycles Water vapour permeability : Not less then 2.0mg / cm 2 Water vapour coefficient : Not less then 30mg / cm 2 Quarter lining material : Breathable Cambrelle mesh lining with antimicrobial treatment for odour control and more comfortable feet Acme Fabrik Plast Company, NH-3, Agra Bombay Road, Girwai, Gwalior (MP), India

11 11 Insole Material : Non woven based insole not less than 2mm thick ph Value : Not less than 3.5 If the ph value is below 4 then differential figure shall be less than 0.7 Water vapour absorption : Not less than 35% (m / m) Water desorption : Not less than 40%(m /m) of the water absorbed Acme Fabrik Plast Company, NH-3, Agra Bombay Road, Girwai, Gwalior (MP), India

12 Acme Fabrik Plast Company, NH-3, Agra Bombay Road, Girwai, Gwalior (MP), India ACME FABRIK PLAST COMPANY 12 Sole Material : Flexible Polyurethane Manufacturing Process : Direct Injection Process (DIP) Relative Density : Heat resistance : up to 120 Centigrade Shore hardness : up to 60 Shore A Tear strength : Not less than 5 Kilo Newtons / m Abrasion resistance : Less than 250mm 3 Flexing resistance : Maximum 4mm cut growth before flexes Fuel Oil resistance : Increase in volume not greater than 12% Other Properties : Anti-skid, acid, alkali & water-resistant

13 13 Toe Cap Material Impact resistance Compression resistance Thread Material Colour Properties : Alloy Steel : Minimum 14 mm clearance on 200 Joules impact : Minimum 14mm clearance on putting a load of 15 Kilo Newton : Nylon or Polyester : Orange : Z twist, oil, acid, chemical proof Acme Fabrik Plast Company, NH-3, Agra Bombay Road, Girwai, Gwalior (MP), India

14 14 Laces Material : Nylon Colour : Black Length : 85 +/- 5 cm Size Size range : Available in sizes 5 to 11 (39-45) Eyelets Material : Nickel Brass Numbers : 3 Acme Fabrik Plast Company, NH-3, Agra Bombay Road, Girwai, Gwalior (MP), India

15 15 Packing Each pair to be packed in 3 ply corrugated box Wrapped around with 45 micron clear Polybag 55 Micron outer carry bag 10 pairs packed in one master carton (9 ply) Warranty Warranty period Warranty Material testing Laboratory : 12 months : In case of sole defect within the warranty period shoe will be replaced free of cost : FDDI - Noida Acme Fabrik Plast Company, NH-3, Agra Bombay Road, Girwai, Gwalior (MP), India