3300C Slade s Cost Effective Pump and Valve Packing HIGH PURITY EXPANDED GRAPHITE PACKING

Transcription

1

2 3300C Slade s Cost Effective Pump and Valve Packing Reinforcement: Each yarn of graphite foil of 99.26% purity (by weight) is reinforced with high strength structural carbon fibre. Temp: Non-oxidizers environments: -400 F ~ 5400 F / -240 C ~ 3000 C Mild Oxidizers environments: up to 1800 F/1000 C Max-oxidizer environments: up to 1200 F/650 C Max Working temp for steam: up to 1800 F/1000 C Density before compression Density die formed (25% compression) Ash Inhibitor type Valves to 1000 PSI/70 BAR (for higher pressures, consult factory) 1-14 (Chemical resistance range) Without cooling flush up to 4800 ft/min or 24.4 m/s 88 lb/ft3 / 1.41 g/cm² 117 lb/ft3 / g/cm² Carbon fibre per yarn 10% by weight Chloride leachable Total chloride Fluorine leachable Total fluorine Sulphur leachable Total sulphur 24ppm 3300W: Inconel wire reinforced for higher pressures: 5000 PSI/350 BAR 3300LC: 3300LS: Applications: Low chloride, high purity for nuclear service Low sulphur, high purity for nuclear service Product recommended for flush free pump service with leak free performance in most applications; contact the factory for specific recommendations. Used in high pressure heater drain pumps, condensate, boiler fee, recirculation, make-up water, cooling water, auxiliary boiler fee, vacuum, and many other water related pumps. COMMONLY USED IN STEAM & CHEMICAL APPLICATIONS. Recommended for valve emission containment up to 1000 C. The above data, collected from in-house testing, field testing, and field applications, is subject to change without notice and must be used for examination ONLY. Contact the factory for suggestions on your specific application. Specific applications must be independently tested for safety and suitability. Failure to independently test can result in property damage and/or personal injury.

3 3300CJ Slade s Anti-Extrusion Carbon Fibre Packing Description: Temp: Density: Density die formed: Ash: Inhibitor type: Carbon fibre per yarn: Graphite: Polytetrafluoroethylene: Chloride leachable: Total chloride: Fluorine leachable: Total fluorine: Total sulphur: Application: Carbon jacketed 3300C where each yarn of graphite foil of 99.26% purity (by weight) is reinforced with high strength structural carbon fibre. Valves to 5000 PSI/345 BAR (for higher pressures, consult factory) Max Working temp for steam: up to 1200 F/650 C Non-oxidizers environments: up to 1200 F/650 C Mild Oxidizers environments: up to 1200 F/650 C Max-oxidizer environments: up to 1200 F/650 C (not oxygen service): 0-14 (Chemical resistance range, except in strong oxidizers) Without cooling flush up to 4800 ft./min or 24.4 m/s 88 lb/ft3 / 1.41 g/cm² (before compression) 117 lb/ft3 / g/cm² (25% compression) 70% by weight 25% by weight 5% by weight For flush free pump service with virtually leak free performance, contact the factory for specific recommendations. Product recommended as an anti-extrusion or bull ring in high pressure pumps and valves as well as an antiabrasion bottom ring in slurry applications. Commonly used in steam & chemical applications. Recommended for valve emission containment up to 1200 F/650 C. Lifetime warranty for valves. (Refer to Warranty Certificate for details.) The above data, collected from in-house testing, field testing, and field applications, is subject to change without notice and must be used for examination ONLY. Contact the factory for suggestions on your specific application. Specific applications must be independently tested for safety and suitability. Failure to independently test can result in property damage and/or personal injury.

4 3300CJK Slade s Anti-Extrusion Carbon Fibre Packing Description: Same as 3300C where each yarn of graphite foil of 99.26% purity (by weight) is reinforced with high strength structural carbon fibre and with Kevlar corners. Temp: Density: Density die formed : Ash: Inhibitor type: Carbon fibre per yarn: Aramid Graphite: Flexible graphite: Graphite impregnate: Chloride leachable: Total chloride: Fluorine leachable: Total fluorine: Total sulphur: Application: Max Working temp for steam: up to 500 F/260 C Non-oxidizers environments: up to 500 F/260 C Mild Oxidizers environments: up to 1200 F/650 C Max-oxidizer environments: up to 350 F/175 C (not oxygen service) Valves to 5000 PSI/345 BAR (for higher pressures, consult factory) 2-12 (Chemical resistance range, except in strong oxidizers) Without cooling flush up to 2500 ft./min or 12.7 m/s 77 lb/ft3 / 1.23 g/cm² (before compression) 103 lb/ft3 / 1.64 g/cm² (25% compression) 66% by weight 25% by weight 8% by weight 1% by weight For flush free pump service with virtually leak free performance, contact the factory for specific recommendations. Carbon jacketed graphite & Kevlar packing used as an antiextrusion or bull ring in high pressure applications, also as an anti-abrasion bottom ring in slurry applications (especially with large throat clearances) and to provide barrier to particulate contamination. Commonly used in steam & chemical applications. Recommended up to 500 F/260 C. The above data, collected from in-house testing, field testing, and field applications, is subject to change without notice and must be used for examination ONLY. Contact the factory for suggestions on your specific application. Specific applications must be independently tested for safety and suitability. Failure to independently test can result in property damage and/or personal injury.

5 3300G Slade s Best All Purpose Pump and Valve Packing Reinforcement: Yarn of graphite foil of 99.26% purity (by weight) is reinforced with high strength structural carbon fibre corners. Temp: Non-oxidizers environments: 5400 F / 3000 C Max-oxidizer environments: 1200 F/650 C Max Working temp for oil: 1800 F/1000 C Max Working temp for steam: 1800 F/1000 C Valves to 5000 PSI/350 BAR Density Density die formed Ash Inhibitor type ft./min (24.4 m/s) without cooling 88 lb/ft3 / 1.41 g/cm² (before compression) 117 lb/ft3 / g/cm² (25% compression) Carbon fibre per yarn 10% by weight Chloride leachable Total chloride Fluorine leachable Total fluorine Sulphur leachable Total sulphur Applications: 24ppm Product recommended for flush free pump service with leak free performance in most applications; contact the factory for specific recommendations. Used in high pressure heater drain pumps, condensate, boiler fee, recirculation, make-up water, cooling water, auxiliary boiler fee, vacuum, and many other water related pumps. COMMONLY USED IN STEAM, hydrocarbons & CHEMICAL APPLICATIONS. Recommended for valve emission containment up to 1000 C Lifetime warranty for valves. (Refer to Warranty Certificate for details.) The above data, collected from in-house testing, field testing, and field applications, is subject to change without notice and must be used for examination ONLY. Contact the factory for suggestions on your specific application. Specific applications must be independently tested for safety and suitability. Failure to independently test can result in property damage and/or personal injury. Advantages: - One packing inventory for all pumps and valves - Works well on worn sleeves - Difficult to overtighten - No added lubricants to squeeze out or burn off - Eliminates flush-water in most applications - Not necessary to replace entire set, just add ring - Won t glaze or harden - Eliminates most leaks - Amperage reduction of 15% is typical - No special end-rings required - Outlasts typical packings by factor of fpm/24 ms (without flush water) - ph Operates virtually leak-free in most applications - Low chloride/sulphur available for nuclear service

6 3300K Slade s Best Triplex Pump, Reciprocating Packing Reinforcement: Each yarn of graphite foil of 99.26% purity (by weight) is reinforced with high strength structural carbon fibre (Same as 3300C) but with added Kevlar fibre corners. Temp: Max Working temp: 500 F / 260 C Non-oxidizers environments: 500 F / 260 C Max-oxidizer environments: 500 F/ 260 C (not oxygen service) 5000 PSI/350 BAR Density: Density die formed: Ash: Inhibitor type: Carbon fibre: Kevlar fibre: Graphite: Chloride leachable: Total chloride: Fluorine leachable: Total fluorine: Total sulphur: Applications: ft./min (12.7 m/s) without cooling 88 lb/ft3 / 1.41 g/cm² (before compression) 117 lb/ft3 / g/cm² (25% compression) 10% by weight (per yarn) 18% by weight 72% by weight For flush free pump service with virtually leak free performance, contact the factory for specific recommendations. Kevlar packing commonly used in oil well sucker rod applications and reciprocating / plunger, wastewater, steam, ammonia pumps. The above data, collected from in-house testing, field testing, and field applications, is subject to change without notice and must be used for examination ONLY. Contact the factory for suggestions on your specific application. Specific applications must be independently tested for safety and suitability. Failure to independently test can result in property damage and/or personal injury.

7 Slade 3300i Low Emission API 622 Certified Valve Packing Slade s 3300i style packing combines the strength of Inconel 600 wire that prevents extrusion of graphite, and the resilient lubricity properties of Slade patented yarns ensures the superior performance of a low emission valve stem packing. Slade 3300i Low Emissions Valve Packing was tested and passed API 622, 2nd Edition. 3300i Low Emissions Valve Packing also proven to be non-corrosive after a 35 day corrosion test as part of the API 622 (2nd edition) test. 3300i Slade Low Emission API 622 (2 nd Ed.) Certified Valve Packing Reinforcement: Temp: Utilizes Inconel 600 wire as a knitted jacket around the Slade patented expanded graphite, carbon reinforced yarns Mild Oxidizers to 1800 F/1000 C* (Inert Environment) Steam 1200 F / 650 C Valves to 6000 PSI/414 BAR (for higher pressures, consult factory)* 0-14 (except in strong oxidizers) * Higher temperatures MAY lower the pressure over 1000 F/540 C, consult the factory

8 Pyro-Tex Gasket Sheet Stainless Steel Reinforced Woven Graphite Sheet Patent Protection: US and Foreign Patents Construction of Gasket: Woven & Compressed sheet gasketing. Construction of Weaving Yarns: Individual flat 304 SS foil strips (not wire), encapsulated in graphite, form unique metal/graphite yarns suitable for weaving 80 x80 high strength sheets. The woven metal strips act as leaf springs to provide resilience during frequent thermal cycling. Temp: Up to 1000 C 1-14 Applications: Advantages: Up to 4500 PSI/310 BAR Heat Exchangers, large cross section flanges, ventilator housings, High temperature, high pressure critical services - Can be used on warped and heavily oxidized surfaces - Change gasket without pulling out the tube bundles - Adhesive bonds in place during installation - Self-forms into endless gasket - Made to virtually any thickness or width - Never hardens or dries out - Metallic reinforcement impedes extrusion - Re-adjustable, often re-usable - Individual strands reinforced with carbon fibre or 304 SS - Packaged on plastic spools - Eliminates large inventories; normally just two sizes needed - More reliable than PTFE joint sealants TYPICAL PHYSICAL PROPERTIES PROPERTY ENGLISH METRIC Density 75 lb/ft g/cm3 Leachable chlorides <10 PPM <10 PPM Sulphur* <360 PPM <360 PPM Ash content <0.74% <0.74% Compressibility (Troom) 40% 40% Recovery (Troom) 10% 10% Tensile along length 2200 psi MPa Compressive strength 35,000 psi 240 MPa Temperature range Inert media -400O F 1400O F -240O C 760O C Steam 1200OF 650OC Oxidizing media -400O F 975O F -200O C 525O C Strong oxidizers Consult Factory Consult Factory Maximum fluid pressure 4500 psi 310 bar/ 31 MPa M Factor 3 3 Y Stress 2900 psi 20 MPa *Use Pyro-Tex Gasket Sheet GLC-2 for high purity applications in nuclear power generation. The GASKET in a CLASS of ITS OWN According to the BHR Group report, Development of Gaskets Made from Expanded Graphite by M. Gawlinski and J. Blachura (given at the Sealing for Pollution Prevention and Control 18th International Conference on Fluid Sealing in Belgium), the Pyro-Tex Woven Gasket (1) maintains a superior tightness over other graphite gaskets during temperature cycling due to its adherence to the sealing surface; (2) operates with high tightness due to the low tangential resistance at compression. Thus, a larger than typical compression set, due to the presence of raised graphite surface nodules, is not a deterrent to its sealing capabilities. The nodules, as illustrated below, are designed to flow into flange surface imperfections. This nodule technology, making a high-quality gasket, puts the Pyro-Tex Gasket Sheet in a different classification when standard commercial tests are performed. The disparity in free thickness due to the surface nodules is much greater than the thickness at which a seal is achieved. The above data, collected from in-house testing, field testing, and field applications, is subject to change without notice and must be used for examination ONLY. Contact the factory for suggestions on your specific application. Specific applications must be independently tested for safety and suitability. Failure to independently test can result in property damage and/or personal injury.

9 Pyro-Tex Joint Sealant HP Self-Forming Gasket PATENTED Pyro-Tex HP Joint Sealant / Gasket is available with the patented stainless-steel foil yarns for HP (high-pressure) applications. Inconel option is also available, consult factory. Available in 25 and 50 foot spools in various configurations, shapes, and thicknesses. HIGH PRESSURE (HP) 304 STAINLESS STEEL FOIL REINFORCED GASKET TYPE SS reinforced joint sealant STYLE/NAME HP Pyro-Tex STANDARD PACKAGING ON SPOOLS 25' & 50' lengths STANDARD SHAPES Rectangular & Semi Round NON-STANDARD SHAPES Delta, Round & as Specified by Customer AVERAGE COMPOSITION MAIN COMPONENT Graphite & SS Foils STATE OF MAIN COMPONENTS Braided, woven & calendared to shape TYPICAL DENSITY lb/ft3 (g/cm) 84.3 (1.35) GRAPHITE PURITY % Weight ASH % Weight 0.74 VERMICULATED GRAPHITE FOIL % Weight STAINLESS STEEL FOIL % Weight 18 CHLORIDE LEACHABLE ppm 10 TOTAL pp 50 TYPICAL STANDARDS FLUORINE LEACHABLE ppm 10 TOTAL FLOURINE ppm 50 SULFUR LEACHABLE ppm 24 TOTAL SULFUR ppm 330 WORKING PARAMETERS MAX TEMP IN OXYGENATED ENV. F/ C 1000/538 MAX TEMP NON-OXY ENV F/ C 1400/760 MAX WORKING TEMP OIL F/ C 1400/760 MAX WORKINGTEMP STEAM & EXHAUST GASES F/ C 1400/760 MAXIMUM PRESSURE RESISTANCE bar/psi 310/4500 CHEMICAL RESISTANCE ph Contact Factory M: Maintenance Factor* 4 Y: Minimum Seating Stress* psi/bar 2200/152 *Based upon bolted flange joint strength analysis, not leakage results. Not intended to give gasket stress assembly limitations. The above data, collected from in-house testing, field testing, and field applications, is subject to change without notice and must be used for examination ONLY. Contact the factory for suggestions on your specific application. Specific applications must be independently tested for safety and suitability. Failure to independently test can result in property damage and/or personal injury.