CAMPUS Datasheet. Ultramid B3EG3 - PA6-GF15 BASF

Transcription

1 CAMPUS Datasheet Ultramid B3EG3 - PA6-GF15 Product Texts Glass fibre reinforced injection moulding grade for housings (e.g: automotive mirror housings). Also used for wheels of mountain bikes. Rheological properties dry / cond Unit Test Standard Melt volume-flow rate, MVR 55 / * cm³/1min ISO 1133 Temperature 275 / * C ISO 1133 Load 5 / * kg ISO 1133 Mechanical properties dry / cond Unit Test Standard Tensile modulus 58 / 35 MPa ISO 527-1/-2 Stress at break 13 / 7 MPa ISO 527-1/-2 Strain at break 3.5 / 15 % ISO 527-1/-2 Tensile creep modulus, 1h * / 25 MPa ISO Tensile creep modulus, 1h * / 21 MPa ISO Charpy impact strength, +23 C 5 / 15 kj/m² ISO 179/1eU Charpy impact strength, -3 C 45 / - kj/m² ISO 179/1eU Charpy notched impact strength, +23 C 8 / 2 kj/m² ISO 179/1eA Charpy notched impact strength, -3 C 7 / - kj/m² ISO 179/1eA Thermal properties dry / cond Unit Test Standard Melting temperature, 1 C/min 22 / * C ISO /-3 Temp. of deflection under load, 1.8 MPa 19 / * C ISO 75-1/-2 Temp. of deflection under load,.45 MPa 215 / * C ISO 75-1/-2 Vicat softening temperature, 5 C/h 5N 21 / * C ISO 36 Coeff. of linear therm. expansion, parallel 32.5 / * E-6/K ISO /-2 Coeff. of linear therm. expansion, normal 75 / * E-6/K ISO /-2 Burning Behav. at 1.5 mm nom. thickn. HB / * class IEC Thickness tested (1.5) 1.6 / * mm IEC Yellow Card available Yes / * - - Burning Behav. at thickness h HB / * class IEC Thickness tested (h).8 / * mm IEC Yellow Card available Yes / * - - Oxygen index 22.5 / * % ISO /-2 Electrical properties dry / cond Unit Test Standard Relative permittivity, 1MHz 3.8 / 7 - IEC Dissipation factor, 1Hz 25 / 24 E-4 IEC Dissipation factor, 1MHz 25 / 24 E-4 IEC Volume resistivity 1E13 / 1E1 Ohm*m IEC Surface resistivity * / 1E1 Ohm IEC Electric strength 41 / 35 kv/mm IEC Comparative tracking index - / 55 - IEC 6112 Other properties dry / cond Unit Test Standard Water absorption 8 / * % Sim. to ISO 62 Humidity absorption 2.6 / * % Sim. to ISO 62 Density 123 / - kg/m³ ISO 1183 Last update: Source: Page: 1/6

2 Material specific properties dry / cond Unit Test Standard Viscosity number 14 / * cm³/g ISO 37, 1157, 1628 Rheological calculation properties Value Unit Test Standard Ejection temperature 15 C - Test specimen production Value Unit Test Standard Injection Molding, melt temperature 28 C ISO 294 Injection Molding, mold temperature 8 C ISO 1724 Injection Molding, injection velocity 2 mm/s ISO 294 Diagrams Viscosity-shear rate Shearstress-shear rate Viscosity-shear rate Ultramid B3EG3 Shearstress-shear rate Ultramid B3EG3 1E3 27 C 28 C 29 C 1E6 27 C 28 C 29 C Viscosity in Pa s 1E2 Shearstress in Pa 1E5 1E4 1E1 1E 1E1 1E2 1E3 1E4 1E5 1E3 1E 1E1 1E2 1E3 1E4 1E5 Shear rate in 1/s Shear rate in 1/s Stress-strain (isochronous) 23 C Creep modulus-time 23 C Stress-strain (isochronous) 23 C Ultramid B3EG3 (cond.) (->Ultramid B35EG3) Creep modulus-time 23 C Ultramid B3EG3 (cond.) (->Ultramid B35EG3) Stress in MPa h 1 h 1 h 1 h 1 h Creep modulus in MPa MPa 1 MPa 15 MPa 2 MPa E1 1E2 1E3 1E4 1E5 Time in h Strain in % Last update: Source: Page: 2/6

3 Stress-strain (isochronous) 9 C Creep modulus-time 9 C Stress-strain (isochronous) 9 C Creep modulus-time 9 C Stress in MPa h 1 h 1 h 1 h 1 h Creep modulus in MPa E1 1E2 1E3 1E4 1E5 2 MPa 4 MPa 6 MPa 8 MPa 1 MPa 12 MPa 14 MPa 15 MPa Time in h Strain in % Stress-strain (isochronous) 12 C Creep modulus-time 12 C Stress-strain (isochronous) 12 C Creep modulus-time 12 C Stress in MPa h 1 h 1 h 1 h 1 h Creep modulus in MPa E1 1E2 1E3 1E4 1E5 2 MPa 4 MPa 6 MPa 8 MPa 1 MPa 2 Time in h Strain in % Last update: Source: Page: 3/6

4 Specific volume-temperature (pvt) Specific volume-temperature (pvt) Ultramid B3EG3 Spec. volume in E-3 m³/kg Temperature in C.1 MPa 4 MPa 8 MPa 12 MPa 16 MPa 2 MPa Characteristics Processing Injection Molding Delivery form Pellets Special Characteristics Heat stabilized or stable to heat Regional Availability North America, Europe Additives Lubricants, Release agent Other text information Injection molding PREPROCESSING Pre/Post-processing, max. allowed water content:.15 % Pre/Post-processing, Pre-drying, Temperature: 8 C Pre/Post-processing, Pre-drying, Time: 4 h PROCESSING injection molding, Melt temperature, range: C injection molding, Melt temperature, recommended: 28 C injection molding, Mold temperature, range: 8-9 C injection molding, Mold temperature, recommended: 8 C injection molding, Dwell time, thermoplastics: 1 min Chemical Media Resistance Acids Acetic Acid (5% by mass) (23 C) Citric Acid solution (1% by mass) (23 C) Lactic Acid (1% by mass) (23 C) Hydrochloric Acid (36% by mass) (23 C) Nitric Acid (4% by mass) (23 C) Sulfuric Acid (38% by mass) (23 C) Sulfuric Acid (5% by mass) (23 C) Chromic Acid solution (4% by mass) (23 C) Last update: Source: Page: 4/6

5 Bases Sodium Hydroxide solution (35% by mass) (23 C) Sodium Hydroxide solution (1% by mass) (23 C) Alcohols Hydrocarbons Ketones Ethers Mineral oils Isopropyl alcohol (23 C) Methanol (23 C) Ethanol (23 C) n-hexane (23 C) Toluene (23 C) iso-octane (23 C) Acetone (23 C) Diethyl ether (23 C) SAE 1W4 multigrade motor oil (23 C) SAE 1W4 multigrade motor oil (13 C) Standard Fuels Salt solutions Other Diesel fuel (pref. ISO 1817 Liquid F) (23 C) Diesel fuel (pref. ISO 1817 Liquid F) (>9 C) Sodium Chloride solution (1% by mass) (23 C) Sodium Hypochlorite solution (1% by mass) (23 C) Zinc Chloride solution (5% by mass) (23 C) Ethyl Acetate (23 C) Hydrogen peroxide (23 C) DOT No. 4 Brake fluid (13 C) Ethylene Glycol (5% by mass) in water (18 C) Water (23 C) The data contained in this publication are based on our current knowledge and experience. In view of the many factors that may affect processing and application of our product, these data do not relieve processors from carrying out their own investigations and tests. Any descriptions, drawings, photographs, data, proportions, weights etc. given herein may change without prior information and do not constitute the agreed contractual quality of the product. It is the responsibility of the recipient of our products to ensure that any proprietary rights and existing laws and legislation are observed. NO WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING WARRANTIES OFMERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE MADE REGARDING PRODUCTS DESCRIBED OR DESIGNS, DATA OR INFORMATION SET FORTH, OR THAT THE PRODUCTS, DESIGNS, DATA OR INFORMATION MAY BE USED WITHOUT INFRINGING THEINTELLECTUAL PROPERTY RIGHTS OF OTHERS. Last update: Source: Page: 5/6

6 In order to check the availability of products please contact us or our sales agency. For more information about our products contact your local representative or SE Dept. PM/K Fax: CAMPUS is a registered trademark of CWFG (Chemie Wirtschaftsfoerderungsgesellschaft GmbH, Frankfurt) Last update: Source: Page: 6/6