Alloy Conductors. Percon Alloys. Percon HS95: A high strength, high conductivity conductor with 655 N/mm 2 strength and 63% IACS.

Transcription

1 ALLOY CONDUCTORS Alloy Conductors RoHS compliant alloy conductors were originally invented by Fisk Alloy. Continuously innovating, we now produce a family of high performance alloy conductors, PERCON. Alloy conductors combine copper as the major constituent with other elements to obtain an engineered set of properties. Our Percon alloy conductors balance several competing engineering attributes: breaking load, elongation, electrical resistivity, resistance to thermal softening, mechanical processing and cost. Each alloy is engineered for different applications and product specifications. Fisk provides a full range of alloy conductors either bare, gold, nickel, silver, or tin plated as stranded or bunched constructions, on bobbins or as single end wire in sizes as small as mm (56 AWG). Listed below is the current selection and properties of Percon alloy conductors. Fisk s technology in copper alloys stands ready to tailor required properties or develop new ones as you may find needed. Percon Alloys Percon HS95: A high strength, high conductivity conductor with 655 N/mm 2 strength and 63% IACS. Percon 28: Surpasses the performance requirements of ASTM B624 with 33% more strength, and the requirements for extra high strength conductor in SAE Percon 24: Engineered to meet the requirements of ASTM B624 and SAE Percon 19: Developed to have better performance than and to replace hard cadmium copper. Percon 17: Developed to have better performance than and to replace soft cadmium copper. Percon 15: An economical hard temper alloy when cost is the major consideration.

2 Alloy Conductors ALLOY TEMPER TENSILE STRENGTH N/mm 2 (min) CONDUCTIVITY IACS ELONGATION (min) FLEX LIFE (ASTM B470) RESISTANCE TO THERMAL SOFTENING AVAILABLE PLATINGS Percon HS-95 soft % 6% excellent very good N, S, G Percon 28 soft % 6% excellent excellent N, S, G Percon 24 soft % 6% excellent excellent N, S, G Percon 19 hard % 1% excellent moderate N, S, T, G Percon 17 soft % 6% good moderate N, S, G Percon 15 hard % 1% very good low N, S, T, G We also offer a selection of bimetals, such as Copper-Clad Steel and Copper-Clad Aluminum in various sizes with different plating options. Details are available upon request. N = Nickel, S = Silver, T = Tin, G = Gold Web Catalogue: Engineered Wire ISO 9001:2008/AS9100C 2017 Fisk Alloy, Incorporated. All rights reserved. Percon, Fisk Engineered Wire and the Fisk Engineered Wire logo are trademarks or registered trademarks of Fisk Alloy, Inc.

3 Alloy Wire Fisk Alloy specializes in copper alloy wire, manufacturing it in the shapes and sizes that customers specify with high precision, uniformity, and quality. ALLOY WIRE As an industry leader, Fisk Alloy has continuously developed innovative products and technologies for producing wire in copper alloys. Our processing capabilities range from 10 mm (0.400") to mm ( ", 56 AWG), bare or plated. With a staff of some 200 persons, Fisk manufactures wire to customer specification in the U.S. at our 14,000 m 2 Hawthorne, NJ facility. The long lead time necessary for casting specialty copper alloys requires that we keep a large and varied inventory of these alloys in rod and wire in stock at all times, so that we can respond quickly to market exigencies. Although copper alloys are our specialty we also work with other materials as requested by our customers. Listed below please find a summary of our general capabilities and stocked alloys. Shapes Flat: Thickness: 0.25 to 2.0 mm (0.010 to 0.079") Width: 0.38 to 6.35 mm (0.015 to 0.250") Rectangular: Thickness: 0.25 to 2.0 mm (0.010 to 0.079") Width: 0.25 to 5.0 mm (0.010 to 0.196") Round: to 10 mm ( to.400") Square: 0.25 to 2.0 mm (0.010 to 0.079") Special: Special profiles and sizes tooled and produced to order Surface Finishes Reel to reel electroplated processing of Copper, Gold, Nickel, Silver and Tin in single layers or in multi-layered combinations (e.g. Ni-Au) to specified thickness for each element. Fisk also produces an Advance Tin Barrier (ATB) plating system which reduces insertion forces and increases solderability shelf life.

4 Alloy Wire Tempers To specified tensile strengths from annealed to spring by separate or combined cold work processing and heat treating to temper. Packages 0.1 kg to 500 kg on a variety of coils, drums, reels and spools. Profiled Wire The term profiled wire is applied to any non-standard shape of wire. Rolled profiled wire can be produced in virtually any copper alloy. However, the cold working characteristics of the alloy have considerable impact on the plastic flow of the metal, the efficiency of the rolling process, and the final shape realized. Thus the economics of profiling vary by copper alloy. We would be pleased to help you select the optimal alloy for your needs; please contact us. High Performance Alloys To respond to a strong and increasing demand for miniaturized parts, Fisk Alloy offers a range of High Performance Copper Alloys, such as C18150, C18080, C19700, combining high conductivity of greater than 80% IACS, high tensile strength and superior stress relaxation resistance. Copper Alloys USA (CDA) EUROPE JAPAN C10200 C19400 C52100 Cu-OF CuFe2P CuSn8 C1020 C1940 C5210 C15100 C19700 C54400 CuZr CuFeMgP CuPb4Sn4Zn3 C1510 C1970 C5441 C17200 C26000 C70250 CuBe2 CuZn30 CuNi3Si1 C1720 C2600 C7025 C17510 C36000 C72500 CuNi2Be CuZn36Pb3 CuNi9Sn2 C1751 C3600 C7250 C18080 C42500 C75200 CuCrTiSiAg CuSn3Zn9 CuNi18Zn20 C1808 C4250 C7941 C18150 C51000 CCS CuCr1Zr CuSn5 CCS C1815 C5102 CCS C19150 C51900 CuNi1PbP CuSn6 C1915 C5191 Web Catalogue: Engineered Wire ISO 9001:2008/AS9100C 2017 Fisk Alloy, Incorporated. All rights reserved. Fisk Engineered Wire and the Fisk Engineered Wire logo are trademarks or registered trademarks of Fisk Alloy, Incorporated.

5 Fine Wire Fine and ultra-fine wire from Fisk Alloy leverages our decades of know-how in copper alloy manufacturing to offer custom solutions in fine diameter round wire for the spring and connector industries. FINE WIRE Our efforts in specialty and fine wire at Fisk focus directly on the ever increasing requirements for high performance products at smaller sizes, offering clients a valuable tool for meeting the unique challenges presented by miniaturization. From traditional spring materials in beryllium copper, to alternative berylliumfree systems, our specialty and fine wire products bring together our existing alloy and conductor lines to offer unique combinations of strength, conductivity, formability, and resistance to relaxation or softening. With careful consideration of these attributes and a complete range of available plating solutions, we can meet the requirements of a wide variety of parts from electronic contacts to mechanical springs. Fine and ultra-fine wire in beryllium and berylliumfree copper alloys from Fisk are manufactured in our Hawthorne, NJ facility. Please find below a summary of our capabilities in specialty and fine wire: Alloys Beryllium Copper: C17200, C17510 Beryllium-Free, High-Conductivity: C18080, C18150, Percon 28 Beryllium-Free, High-Strength: C70250 Phosphor Bronze: C51000, C51900, C52100 Other alloys available on request Diameter Fine wire from to mm ( to 0.010")

6 Fine Wire Temper To specified tensile strengths from annealed to spring by separate or combined cold work processing and heat treating to temper Beryllium Copper is available in both heat treatable and pre-tempered conditions Surface Finish As drawn or electroplated with Copper, Gold, Nickel, Silver, Tin, or combinations thereof Packages On a variety of spools, with controlled cast and offset where required Web Catalogue: Engineered Wire ISO 9001:2008/AS9100C 2017 Fisk Alloy, Incorporated. All rights reserved. Fisk Engineered Wire and the Fisk Engineered Wire logo are trademarks or registered trademarks of Fisk Alloy, Incorporated.

7 Machinable Alloys Available in rod or wire, Fisk Alloy copper alloys are optimized for manufacturing machined products that exceed both end use and processing requirements. Machinability, mechanical requirements, physical properties, corrosion resistance, and fabrication all important considerations when selecting the correct copper alloy for manufacturing a machined product. At Fisk, we understand these characteristics and enhance them to maximize performance of our rod and wire products. Wrought from alloys that are cast to our exact specifications and informed by our metallurgical knowhow, Fisk Alloy products receive the right combination of heat treatment and cold work needed to excel in the most demanding applications. Precise control throughout the entire process ensures a highly consistent product providing maximum value for the customer. Machinable alloys from Fisk are manufactured in our Hawthorne, NJ facility. With a sharp focus on precision, quality, and value, we can meet your requirements in a timely manner. Please find below a summary of our capabilities in machinable alloys: Alloys MACHINABLE ALLOYS High Copper: C14500, C18700, C19150, C19160 Brass: C33500, C34000, C34500, C35300, C36000, C38500 RoHS Compliant Lead-Free: BlueBrass 42e Phosphor Bronze: C54400 Nickel Silver: C79200, C79860 Other alloys available on request

8 Machinable Alloys Form Rod or wire, round Diameter Rod from 1 to 8 mm (0.039 to 0.315") Wire from 0.25 to 6.35 mm (0.010 to 0.250") Temper To specified tensile strengths from annealed to spring by separate or combined cold work processing and heat treating to temper Length Rod, 3000 mm (118.1") or mm (144"), standard Ends Rod, finished end configurations, depending on diameter Packages Rod, from 100 to 250 kg (250 to 500 lb), in cases Wire, in standard coils, fiber drums, or on a variety of spools, from 15 to 250 kg (35 to 500 lb) Web Catalogue: Engineered Wire ISO 9001:2008/AS9100C 2017 Fisk Alloy, Incorporated. All rights reserved. Fisk Engineered Wire and the Fisk Engineered Wire logo are trademarks or registered trademarks of Fisk Alloy, Incorporated. BlueBrass and BlueBrass 42e are registered trademarks of Aurubis AG.

9 BlueBrass BlueBrass is a RoHS compliant, lead-free machinable copper alloy, bringing both economic and environmental benefits to precision machining by combining performance and regulatory compliance in a single solution. BlueBrass is a RoHS compliant, lead-free brass with good machinability, high strength, excellent ductility, and ease of recycling. Based on the copper-zinc alloy system and made from common alloying elements, lead is present only in a limited amount for compliance with a growing range of legislative and regulatory guidelines. BlueBrass is recommended for any RoHS compliant machined brass part, and is of particular interest where replacement of traditional leaded brass has proved difficult or impractical due to processing or end use requirements. PROFILED WIRE BlueBrass performance relies on a unique combination of composition and microstructure. This approach alleviates the need for substitution with elements such as silicon, bismuth, and sulfur all of which can have negative impact to recycling and product quality, requiring continuous and costly controls in use. Because of it s RoHS composition, BlueBrass chips can be safely added to the standard scrap stream without exception. This results in both economic and ecologic benefits throughout the supply chain. BlueBrass is flexible by design and having a dedicated development team, we can tailor the properties to your unique situation. BlueBrass 42e BLUE BRASS BlueBrass 42e is a member of the BlueBrass family of alloys, specifically targeted for all electronic products including connector components. When compared to traditional leaded brass, electrical conductivity and machining properties are comparable, while strength

10 BlueBrass and ductility are both markedly improved. The favorable ductility provides increased capacity for hot forming or secondary cold working operations. BlueBrass 42e is available in wire from 0.25 to 6.35 mm (0.010 to 0.250") diameter. Rod products are manufactured with diameters from 1 to 8 mm (0.039 to 0.315") and standard lengths of 3000 (118.1") or (144"). BlueBrass 42e is manufactured and distributed by Fisk Alloy in the USA, in partnership with Aurubis AG. Below is a summary of our capabilities in BlueBrass: Tensile Strength From 450 to 750 MPa (65 to 109 ksi) Yield Strength From 200 to 690 MPa (29 to 100 ksi) Elongation From 35 to 7% Electrical Conductivity 25% IACS Spring Properties / Modulus of Elasticity 105,000 MPa (15,500 ksi) Web Catalogue: Engineered Wire ISO 9001:2008/AS9100C 2014 Fisk Alloy, Incorporated. All rights reserved. Fisk Engineered Wire and the Fisk Engineered Wire logo are trademarks or registered trademarks of Fisk Alloy, Incorporated. BlueBrass and BlueBrass 42e are registered trademarks of Aurubis AG.