FrelTec GmbH. Shielded SMD Power Inductors

Transcription

1 GmbH Mathildenstr. 10A Starnberg Germany 1/28/2013 1/11 GmbH

2 SPECIFICATION Part Number 104 H27 * 101 * M E0A ** Type Size Value Tolerance Packing 104 : Shielded SMD Power Inductor 62B: The value is given in µh and u indicates the decimal point. When higher than 100µH then l the last digit is the multiplier 64B: which denotes the number of zero following M: ±20% E0X : 1500pcs 500pcs for 62B (13" reel) E01 : 1000pcs for 64B, 773 and 774 (13" reel) 773: Example: E0A : 500pcs for H27 and 124 (13" reel) 774: U3 : 3,3 µh E0W : 400pcs for 125 and 127 (13" reel) 124: : 22 µh 125: : 100 µh 127: 12x12x8,0 H27: 12x12x8,0 (High Current) * not all combination is possible 1/28/2013 2/11

3 SMD Dimensions and recommended PCB pattern for reflow soldering: 62B / 64B 773 / /125/127/H27 Inductance and rated current ranges 62B 2,9μH~330μH 1,94~0,19A 64B 10μH~1000μH 1,35~0,14A 773 1,0μH~1000μH 7,97~0,16A 774 1,0μH~1000μH 8,0~0,18A 124 2,5μH~300μH 8,0~0,5A 125 1,3μH~1000μH 8,0~0,4A 127 1,2μH~1000μH 9,8~0,55A H27 4,7μH~1000μH 15,9~1,14A Electrical specifications at 25 C Type H1 H2 H3 max. max. max. H I J 62B 3, ,9 1,4 4,6 64B 5, ,9 1,4 4, ,4-2,2 1,6 4, ,5-2,2 1,6 4, ,5 5,4 2,9 7, ,0 5,4 2,9 7, ,0 5,4 2,9 7,0 H27 8,0 5,4 2,9 7,0 unit: mm 1/28/2013 3/11

4 Test equipment: HP4284A or HP4285A LCR meter DCR: Milli-ohm meter Electrical Characteristics 62B / 64B / 773 / 774 Type Codes RDC IDC L Tolerance (Ω) max. (A) max. (μh) 62B 64B B 64B H0 1, ,016 0, ,970 8,000 1H5 1, ,023 0, ,500 7,000 2H2 2, ,027 0, ,500 6,000 2H9 2,9 0, , H3 3,3 0,075-0,031 0,032 1,800-4,000 4,800 3H9 3, ,041 0, ,800 4,400 4H0 4,0 0, , H7 4,7 0,090-0,048 0,038 1,55-3,500 4,000 5H5 5,5 0, , H6 5, ,056 0, ,000 3,500 6H8 6, ,062 0, ,000 3, ,150 0,120 0,072 0,049 1,100 1,350 1,680 1, ,200 0,130 0,098 0,058 1,000 1,220 1,520 1, ,230 0,180 0,130 0,081 0,900 1,110 1,330 1, ,270 0,240 0,140 0,091 0,800 1,020 1,200 1, ,340 0,270 0,190 0,110 0,740 0,910 1,070 1, ,380 0,300 0,210 0,150 0,660 0,820 0,960 1, ,450 0,330 0,240 0,170 0,590 0,740 0,910 0,960 M ,490 0,370 0,320 0,230 0,540 0,690 0,770 0, ,690 0,520 0,360 0,260 0,500 0,620 0,760 0, ,780 0,560 0,470 0,350 0,460 0,580 0,680 0, ,070 0,630 0,520 0,380 0,420 0,510 0,610 0, ,210 0,710 0,690 0,430 0,380 0,460 0,570 0, ,390 1,030 0,790 0,610 0,340 0,420 0,500 0, ,900 1,150 0,890 0,660 0,310 0,380 0,490 0, ,180 1,680 1,270 0,880 0,280 0,350 0,430 0, ,770 1,870 1,450 0,980 0,260 0,320 0,390 0, ,120 2,080 1,650 1,170 0,230 0,290 0,350 0, ,380 2,370 2,310 1,640 0,220 0,260 0,320 0, ,940 2,670 2,620 1,860 0,190 0,230 0,280 0, ,940 2,940 2,850-0,220 0,260 0, ,930 4,180 3,010-0,200 0,240 0, ,430 4,670 3,620-0,180 0,220 0, ,320 5,730 4,630-0,170 0,190 0, ,240 6,540 5,200-0,150 0,180 0, ,260 9,440 6,000-0,140 0,160 0,180 Measuring Freq: 62B: 0,25V; 0,25V 64B: 0,25V 773: 0,25V 774: 0,25V 1/28/2013 4/11

5 124 / 125 / 127 Type Codes DCR IDC L Tolerance (Ω) max. (A) max. (μh) H2 1, , ,80 1H3 1,3-0, ,00-2H1 2,1-0, ,00-2H2 2,2-0,014 0,010-7,00 8,50 2H4 2, , ,00 2H5 2,5 0, , H7 2, , ,00 3H1 3,1-0, ,00-3H3 3,3-0,014 0,013-6,75 7,80 3H5 3, , ,50 3H9 3,9 0, , H4 4,4-0, ,00-4H7 4,7 0,018 0,018 0,016 5,70 6,20 6,80 5H6 5, , ,70 5H8 5,8-0, ,40-6H1 6, , ,60 6H8 6,8 0,023 0,023 0,014 4,90 5,90 6,40 7H5 7,5-0, ,20-7H6 7, , ,90 8H2 8,2 0, , ,028 0,025 0,022 4,50 4,00 5, ,038 0,027 0,024 4,00 3,50 4, M 0,050 0,030 0,027 3,20 3,30 4, ,057 0,034 0,039 3,10 3,00 3, ,066 0,036 0,043 2,90 2,80 3, ,080 0,051 0,046 2,80 2,30 3, ,097 0,057 0,065 2,70 2,10 3, ,132 0,068 0,073 2,10 2,00 2, ,150 0,075 0,100 1,90 1,80 2, ,190 0,110 0,110 1,80 1,70 2, ,220 0,120 0,140 1,50 1,50 2, ,260 0,140 0,160 1,30 1,40 1, ,308 0,160 0,220 1,20 1,30 1, ,380 0,170 0,250 1,10 1,10 1, ,530 0,230 0,280 0,95 1,00 1, ,620 0,290 0,350 0,85 0,90 1, ,700 0,400 0,390 0,80 0,80 1, ,876 0,460 0,560 0,60 0,75 1, ,990 0,510 0,640 0,50 0,68 0, ,690 0,700-0,65 0, ,770 0,980-0,58 0, ,860 1,070-0,54 0, ,200 1,460-0,48 0, ,340 1,640-0,43 0, ,530 1,820-0,40 0,55 Measuring Freq: 124: 0,25V 125: 0,25V; 0,25V 127: 0,25V; 0,25V 1/28/2013 5/11

6 H27 Type Codes L (uh) 4U7 4,7 Tolerance Test Condition DCR (Ω) Max IDC (A) Max 0,016 15,9 6U8 6,8 0,021 13,3 8U2 8,2 0,023 12, ,024 11, ,031 9, ,040 7, ,070 6, ,080 5, ,105 4, M 100KHz, 0,25V 0,143 3, ,163 3, ,247 3, ,376 2, ,574 2, ,861 1, ,080 1, ,470 1, ,660 1,14 1/28/2013 6/11

7 Tape and Reel Dimensions INDUCTORS Type Tape size Parts Per Reel W P 13 62B B H unit: mm 1/28/2013 7/11

8 Cover Tape Peel off Strength Peel-off force should be in the range 0,1N~0,6N at a peel-off speed of 300±10 mm/min Storage Temperature: 25±3 C Humidity < 80%RH Caracteristics Operating temperature range except H27: -40 C to +85 C Operating temperature range H27: -40 C to +105 C Rated DC Current except H27: The DC current at which the inductance becomes 25% lower than its initial value or when t=40 C, whichever is lower. (Ta=25 C) Rated DC Current H27: The DC current at which the inductance becomes 30% lower than its initial value. (Ta=25 C) Lead Free Reflow Soldering Profile Stock period The performance of these products, including the solderability, is guaranteed for 6 month after production date code, provided that they remain packed as they were when delivered and stored at a temperature of 25 C ± 3 C and a relative humidity less than 80%RH 1/28/2013 8/11

9 Environmental Test Test Items Specifications Test Conditions / Test Methods High temperature Storage Low temperature Storage test Humidity test Thermal shock test Mechanical Test No case deformation or change in appearance. L/L 10% Temperature 85±2 C, Time: 48±2 hours, Tested after 1hour at room temperature. Temperature -40 C, Time: 48±2 hours, Tested after 1hour at room temperature. Temperature 40±2 C, 90~95% relative humidity Time: 96±2 hours, apply rated current, Tested after 1hour at room temperature. First -25 C 30minutes then 25 C 10 minutes last 85 C 30 minutes, as 1 cycle. Go through 5 cycles. Tested after 1 hour at room temperature. Test Items Specifications Test Conditions / Test Methods Solderability test Heat endurance of Reflow soldering Vibration test Shock resistance Terminal area must have 90% minimum solder coverage. No case deformation or change in appearance. L/L 10% Product with Lead-free terminal: Dip pads in flux then dip in solder pot at 245±5 C for 3±0,5 seconds. Refer to the reflow soldering condition. Go through 3 times. Apply frequency 10~55Hz. 1,5mm amplitude in each of perpendicular direction for 2 hours. Drop down with 981m/s 2 (100G) shock attitude upon a rubber block method shock testing machine, for 1 time. In each of three orientations. 1/28/2013 9/11

10 For this part: It does not use the materials that include the substances specified in RoHS, the detail refer to the part of prohibition or exclusion items in RoHS (2002/95/EC). Cadmium and cadmium compounds (permissive content<100 ppm) Lead and lead compounds (permissive content<1000 ppm) Exceptions specified: Lead contained in the glass of cathode ray tubes, electronic components and fluorescent tubes. The glass material used in the electronic components, which includes resistor elements, conductive pastes (silver or copper ones), adhesives, glass frit and sealing materials. Mercury and its mercury compounds (permissive content<1000 ppm) Hexavalent chromium compounds (permissive content<1000 ppm) Polybrominated biphenyls (PBB) (permissive content<1000 ppm) Polybrominated diphenylethers (PBDE) (permissive content<1000 ppm) 1/28/ /11

11 Published by GmbH Mathildenstr. 10A; Starnberg; Germany 2013 GmbH. All Rights Reserved. The following applies to all products named in this publication: 1. The information describes the type of component and shall not be considered as assured characteristics. 2. Terms of delivery and rights to change design reserved. 3. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. Nevertheless, we explicitly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether a product with the properties described in the product specification is suitable for use in a particular customer application. 4. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 5. The warnings, cautions and product-specific notes must be observed. 6. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous ). Useful information on this will be found in our Material Data Sheets. Should you have any more detailed questions, please contact our sales offices. 7. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true for the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. 8. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the General conditions for the supply of products and services of the electrical and electronics industry published by the German Electrical and Electronics Industry Association (ZVEI), available at 9. As far as patents or other rights of third parties are concerned, liability is only assumed for components per se, not for applications, processes and circuits implemented within components or assemblies. 10. The trade name is a trademark registered or pending in Europe and in other countries. 1/28/ /11