Product Data FASSON Polyimide I Matt White - S #SCK

Transcription

1 Facestock A matt white topcoted polyimide film with very high dimensional stability, heat and chemical. The high opacity white topcoat is specifically designed for thermal transfer printing and offers excellent scratch, scuff, UV, high temperature and solvent. Basis weight: 72 g/m² ISO 536 Caliper: 0,043 mm ISO 534 Adhesive S8088 is a high performance acrylic adhesive with excellent heat and chemical. Type: Solvent acrylic Coat weight: 27 g/m² Initial Tack: 220 N/m FTM 9 glass Peel Adhesion: 330 N/m FTM 2 steel 24 hrs. Min. application temperature: +10 C Min. service temperature: -40 C Max. peak temperature: +280 C Liner 50#SCK: siliconized, bleached, super-calendered kraft liner. Good die-cutting and matrix stripping. Suitable for roll-to-roll conversion. Basis weight: 80 g/m² ISO 536 Caliper: 0,081 mm ISO 534 Opacity: 70 % DIN Tensile Strength: 163 N/15mm MD This liner is not recommended for sheeting. Total construction caliper 0,151 mm Typical Values Typical values, not for specification use: see Appendix 1. Applications and use Polyimide I Matt White-S8088 was specially developed for labeling printed circuit boards prior to soldering. The construction is designed to withstand reflow processes regardless if the label is on top or bottom of the board. It can also withstand two cycles of reflow processes when surface mounting elements to both sides of the board. The product is also designed to be used in the wave solder process even when directly exposed to the solder bath. The matt topcoat had been formulated to prevent solder balls forming on top of the label. Application tests are recommended. Printing and conversion The topcoat is designed for thermal transfer and flexo printing. When used with an appropriate ribbon it will withstand temperature spikes up to 280ºC. Due to the thinness of the facestock, automatic dispensing and application should be thoroughly tested prior to committing to production. This product is designed for roll-to-roll conversion. It is not recommended for sheeting. UL approval This product is UL recognized for indoor use and exposure to wave solder applications; the file number is MH For specific information on approved conditions, see appendix 2. RoHS / Regulation 2002/95/EU The substances listed in article 4 lid 1 of 2002/95/EU (RoHS) are not intentionally used in this product. The concentration limits of these substances will not exceed the set maximum concentration limits as provided in the proposed amendment for 2002/95/EU. Shelf life One years when stored at 22 C and 50 %rh.

2 Appendix 1: Performance Data Note: the following technical data should be considered representative or typical only and should not be used for specification purposes. Peel Adhesion: FTM1: 180, 300 mm/min in N/25mm. Surface dwell time 20 min dwell time 24 hrs Epoxy Printed Circuit Board 4,5 7 Stainless steel 4,5 6,5 Short term high temperature The label material has been tested on Epoxy Printed Circuit Board. A typical reflow solder profile with a maximum temperature of 240 C has been processed. No visible changes could be noticed. Print is still legible. Chemical Resistance The performance results are based on simulation of a typical PCB cleaning process including a simulation of a solder process. Cleaning agent Cleaner agent base Process Wash time Temperature ( C) Rinse time Rinse Temperature ( C) Visual appearance Vigon US 1 Water based Ultrasonic 10 min min 80 No change Vigon A200 1 Water based Spray-in-air 10 min min 80 No change Vigon A250 1 Water based Spray-in-air 10 min min 80 No change Vigon A300 1 Water based Spray-in-air 10 min min 80 No change Zestron FA+ 1 Semi-aqueous Dip tank 10 min min 80 No change Zestron VD 1 Solvent based closed-loop processes with steam rinsing Zestron CE 1 Solvent based closed-loop processes with steam rinsing 10 min min 80 No change 10 min min 80 No change Atron AC205 1 Water based Spray-in-air 10 min min 80 No change Aquanox A4625B 2 Water based Spray-in-air 15 min 65 5 min 51 No change Aquanox A Water based Spray-in-air 15 min 65 4 min 51 No change 1 Dr. O.K. Wack-Chemie GmbH 2 Kyzen Corporation

3 Thermal Transfer Printing: Printability Physical Resistance Flat head printers: Ribbon Settings speed energy Print Quality 1 ANSI Grade 2 Scratch Armor AXR A Dai Nippon R A Dai Nippon R A Iimak SP A ITW B A Ricoh B110 A A Ricoh B110 CR A Sony TR A The print tests were performed with the printer Zebra Stripe S-500. Near edge printers: Ribbon Settings Print Quality 1 ANSI Grade 2 Tape Scratch Ricoh B120 Ec 4 /s ++ A ++ - Sony TR /s ++ A ++ o The print tests were performed with the printer Avery TTX 450 Near Edge. 1 Print Quality: ++: excellent +: good o: acceptable -: poor 2 ANSI (American National Standards Institute) Grade,information about barcode quality: A: excellent B: good C: acceptable D: readable with difficulty Tape Chemical Resistance The printed samples passed a simulation of a typical PCB cleaning processes (including solder process simulation) as described beforehand. Afterwards the evaluation took place. AXR7+ R300 R510 SP330 B324 B110 B110A TR6075 CR Vigon US 3 + NT o o + Vigon A NT Vigon A NT + + o Vigon A NT o + + Zestron FA+ 3 o NT o + o o - o Zestron VD 3 + NT + NT + + o NT Zestron CE 3 - NT + NT Atron AC NT NT + o NT Aquanox A4625B 4 + NT + NT NT + + NT Aquanox A NT + NT NT + NT +: good (no change) o: acceptable (minor change, still readable) -: poor NT.: not tested 3 Dr. O.K. Wack-Chemie GmbH 4 Kyzen Corporation

4 Appendix 2: Compliance Data UL Underwriters Laboratories File Number: MH27538 This material is UL recognized for exposure indoors to high humidity or occasional exposure to water. Substrate Minimum Temperature ( C) Maximum Temperature ( C) Aluminum Galvanized steel Stainless steel Epoxy Resin PWB The UL recognition includes wave solder applications at 300 C for 5 seconds on Epoxy Resin PWB. The UL certification includes the printing with one or more of the following thermal transfer ribbons: DNP "R-510" and "R-300", and ITW "B324".

5 Warranty All statements, technical information and recommendations about AVERY DENNISON products are based upon tests believed to be reliable but do not constitute a guarantee or warranty. All AVERY DENNISON products are sold with the understanding that PURCHASER has independently determined the suitability of such products for its purposes. AVERY DENNISON products are warranted to be free of defects in material or workmanship for a period of one year from the date of shipment. Any product shown to the satisfaction of AVERY DENNISON within the time provided to be so defective shall be replaced without charge or AVERY DENNISON may issue credit in such amount as it deems reasonable however, in no event shall AVERY DENNISON be responsible for claims beyond the replacement value of the defective product or in any way liable or responsible for consequential or incidental damages. NO EXPRESS WARRANTIES AND NO IMPLIED WARRANTIES, WHETHER OF MERCHANTIBILITY OR FITNESS FOR ANY PARTICULAR USE, OR OTHERWISE, EXCEPT AS SET FORTH ABOVE (WHICH IS MADE EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES) SHALL APPLY TO PRODUCTS SOLD BY AVERY DENNISON. AVERY DENNISON SPECIFICALLY DISCLAIMS AND EXCLUDES ALL OTHER SUCH WARRANTIES. NO WAIVER, ALTERATION, ADDITION OR MODIFICATION OF THE FOREGOING CONDITIONS SHALL BE VALID UNLESS MADE IN WRITING AND SIGNED BY AN EXECUTIVE OFFICER OF AVERY DENNISON. No salesman, representative, or agent of AVERY DENNISON is authorized to give any guarantee, warranty or make any representation contrary to the above.