RPU 60. RPU 60 is a tough, abrasion-resistant material that is a good choice for parts that require rigidity, strength, and durability.

Transcription

1 RPU 60 VERSION 1 TECHNICAL DATA SHEET 8/1/16 V3.3 RPU 60 RPU 60 is a tough, abrasion-resistant material that is a good choice for parts that require rigidity, strength, and durability. NOTES Test specimens were prepared using Carbon M1 printer and a Type B cassette. Print parameters were generated using software v Tensile data were generated using printed Type V samples (per ASTM D638). All other test specimens were printed following standard ASTM test geometries. All test specimens were printed, cleaned, and post-processed per instructions provided in the Carbon User Manual. Liquid property measurements were carried out using fully mixed resins. Results provided herein are representative of these processes and may vary if these established protocols are not followed.

2 RPU 60 VERSION 1 TECHNICAL DATA SHEET 8/1/16 V3.3 Tensile Properties ASTM D638 Ultimate Tensile Strength 48 ± 8 MPa 7000 ± 1000 psi Tensile Strength at Yield 42 ± 2 MPa 6100 ± 200 psi Elongation at Yield 6 ± 1 % 6 ± 1 % Modulus 1600 ± 100 MPa 230 ± 15 ksi Elongation-at-Break 130 ± 10 % 130 ± 10 % Flexural Properties ASTM D790 Flexural Strength 42 ± 2 MPa 6000 ± 250 psi Flexural Modulus 1450 ± 500 MPa 210 ± 8 ksi Impact Properties ASTM D256, ASTM D4812 IMPACT STRENGTH IMPACT STRENGTH IMPACT ENERGY Machined Izod notch 29 ± 1 J/m 0.54 ± 0.02 ft-lb/in. 2.8 ± 0.1 kj/m ± 0.1 ft-lb/in 2 Izod Unnotched 770 ± 40 J/m 14 ± 1 ft-lb/in. 75 ± 5 kj/m 2 35 ± 2 ft-lb/in 2

3 RPU 60 VERSION 1 TECHNICAL DATA SHEET 8/1/16 V3.3 Thermal 0.45 MPa/66 psi (ASTM 1.82 MPa/264 psi (ASTM D648) 58 C 136 F 49 C 120 F Tg (DMA, E ) 64 C 147 F Tg (DMA, tan(d)) 100 C 212 F Coefficient of Thermal Expansion (ASTM E228) 180 ppm/ C Liquid Properties Viscosity (@25 C, cp) 5500 ± 500 Liquid Density C) 1.02

4 RPU 61 VERSION 1 TECHNICAL DATA SHEET 7/7/16 V1.2 RPU 61 RPU 61 is a tough, and abrasion-resistant higher resolution material that is a good choice for parts that require rigidity, strength, and durability. NOTES Test specimens were prepared using a Carbon M1 printer and a Type C cassette. Print parameters were generated using software Tensile data were generated using printed Type V samples (per ASTM D638). All other test specimens were printed following standard ASTM test geometries. All test specimens were printed, cleaned, and post-processed per instructions provided in the Carbon User Manual. Liquid property measurements were carried out using fully mixed resins. Results provided herein are representative of these processes and may vary if these established protocols are not followed.

5 RPU 61 VERSION 1 TECHNICAL DATA SHEET 7/7/16 V1.2 Tensile Properties ASTM D638 Ultimate Tensile Strength 42 ± 3 MPa 6100 ± 450 psi Tensile Strength at Yield 40 ± 2 MPa 5800 ± 290 psi Elongation at Yield 6 ± 1 % 6 ± 1 % Modulus 1500 ± 100 MPa 218 ± 15 ksi Elongation-at-Break 120 ± 10 % 120 ± 10 % Flexural Properties ASTM D790 Flexural Strength 37 ± 2 MPa 5400 ± 300 psi Flexural Modulus 1100 ± 100 MPa 160 ± 15 ksi Impact Properties ASTM D256, ASTM D4812, ISO 179 IMPACT STRENGTH Machined notch, Izod 27 ± 2 J/m 0.5 ± 0.04 ft-lb/in. Unnotched, Izod 1200 ± 200 J/m 22 ± 4 ft-lb/in. Machined notch, Charpy 2.2 ± 0.4 kj/m ± 0.2 ft-lb/in 2

6 RPU 61 VERSION 1 TECHNICAL DATA SHEET 7/7/16 V1.2 Thermal 0.45 MPa/66 psi (ASTM 1.82 MPa/264 psi (ASTM D648) 59 C 137 F 48 C 119 F Tg (DMA, E ) 53 C 128 F Tg (DMA, tan(d)) 98 C 208 F Coefficient of Thermal Expansion (ASTM D696) 66 ppm/ C Dielectric Properties Dissipation Factor (ASTM D150, 1 MHz) Dielectric Constant, k (ASTM D150, 1 MHz) 3.10 Liquid Properties Viscosity (@25 C, cp) 6000 ± 500 Liquid Density C)

7 RPU 70 VERSION 1 TECHNICAL DATA SHEET 8/1/16 V3.3 RPU 70 RPU 70 is a tough, heat resistant material that is a good choice for parts requiring strength, toughness, and moderate heat resistance. NOTES Test specimens were prepared using Carbon M1 printer and a Type B cassette. Print parameters were generated using software v Tensile data were generated using printed Type V samples (per ASTM D638). All other test specimens were printed following standard ASTM test geometries. All test specimens were printed, cleaned, and post-processed per instructions provided in the Carbon User Manual. Liquid property measurements were carried out using fully mixed resins. Results provided herein are representative of these processes and may vary if these established protocols are not followed.

8 RPU 70 VERSION 1 TECHNICAL DATA SHEET 8/1/16 V3.3 Tensile Properties ASTM D638 Ultimate Tensile Strength 45 ± 2 MPa 6500 ± 300 psi Tensile Strength at Yield 45 ± 2 MPa 6500 ± 300 psi Modulus 1900 ± 200 MPa 290 ± 30 ksi Elongation-at-Break 100 ± 20 % 100 ± 20 % Flexural Properties ASTM D790 Flexural Strength 62 ± 9 MPa 9000 ± 1300 psi Flexural Modulus 1800 ± 300 MPa 261 ± 40 ksi Impact Properties ASTM D256, ASTM D4812 IMPACT STRENGTH IMPACT STRENGTH IMPACT ENERGY Machined Izod notch 22 ± 1 J/m 0.41 ± 0.02 ft-lb/in. 2.2 ± 0.1 kj/m ± 0.05 ft-lb/in 2 Izod Unnotched 530 ± 30 J/m 9.9 ± 0.5 ft-lb/in. 52 ± 3 kj/m 2 25 ± 2 ft-lb/in 2

9 RPU 70 VERSION 1 TECHNICAL DATA SHEET 8/1/16 V3.3 Thermal 0.45 MPa/66 psi (ASTM 1.82 MPa/264 psi (ASTM D648) 70 C 160 F 55 C 130 F Tg (DMA, E ) 80 C 176 F Tg (DMA, tan(d)) 119 C 246 F Coefficient of Thermal Expansion (ASTM E228) 160 ppm/ C Liquid Properties Viscosity (@25 C, cp) 2200 ± 100 Liquid Density C) 1.01